Search Documents

By P. van Zyl, M. Lombaard

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Jan 1, 2012

By Thomas Schemmel, Bertram Kesseiheim, Helge Jansen, Uwe Kreme

"During the last decades the refractory life time of the different aggregates of the secondary aluminium production was improved significantly. However, each repair and installation of refractory material affects the operating schedule and can cause costs in the million range. The downtime of just one melting furnace generate costs of 100.000 to 400.000 $ per day. Besides cooling down of the furnace and its repair, the heating-up procedure accounts for the longest time of the shutdown. Usually, heating-up of low cement or ultra low cement castables takes 120 to 150 hours. In order to reduce such expensive downtimes Refratechnik developed a unique and novel product series: Nanobond. These materials can be heated-up in only a third of the usual time. This paper talks about the theoretical aspects, as well as the mechanical and physical properties and especially practical experience of using Nanobond.Theoretical Aspects and Laboratory ResultsCement containing castables such as RCC, MCC, LCC or ULCC are considered standard in many refractory applications. Over the years a wide range of possible raw materials and practical installation methods were developed. However, all of these cement bonded refractory mixes possess one main important drawback. Such materials are characterized by the hydration of the cement bonding. As a result the physical bonded and the hydraulic water has to be removed in a relatively complicated drying procedure. The hydraulic water specifically demands a very careful and cautious heating up procedure. Most of the dreaded steam explosions can occur at a furnace temperature of approx. 250 oC. [1] To avoid such destructions, the heating-up of a new lined or repaired furnace can be very complex and slow. Depending on the furnace or the casted part a drying time of several days with long curing times are common."

Jan 1, 2012

Experimental determination of the response of an AG/SAG mill treating two components of significantly different impact resistance is challenging for two main reasons: firstly, small scale laboratory tests have yet to be confirmed as valid representations of the full scale milling environment, and secondly pilot plant testing requires 10-20 tonnes of ore per scenario which precludes the use of drill core, rendering the process very expensive. In order to mitigate these difficulties, modelling was considered as a potential way forward. However, as the JKSimMet AG/SAG model currently has no capacity to simulate the interaction of two ore types with differing impact resistance, density and/or feed size distributions, an alternative modelling approach was developed. This approach aims to essentially calibrate the AG/SAG process under a set of given conditions, for which survey data and the ore properties of the main components in the feed blend already exist. This paper describes a new conceptual model, which provides a simplified approach for investigating the multi-component behaviour of two ores of differing hardness/SG in a given AG/SAG milling environment, and which can potentially be used for scale-up from laboratory/pilot testwork and geometallurgical estimation of throughput.

Jan 1, 2012

By K. Becerra, D. G. Almond, T. D. Maru

"Nkomati Nickel Mine in South Africa processes one of the world’s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster.Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program.The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control."

Jan 1, 2012

By V. “Ram” Ramachandran

"In view of the increasing number of environmental regulations that have been promulgated all over the world in the last thirty years, non-ferrous smelters and refineries have had to learn and adapt to treating process bleed waste streams containing heavy metals. The result of such treatment invariably yields a gypsum-saturated solution containing salts such as alkali metal sulfates, chlorides and fluorides. Presence of anions such as sulfates, chlorides and fluorides in the discharge streams – presently not a major problem- are coming under increasing scrutiny and will have to be addressed in the near future. It is envisaged that discharge limits for sulfate ions will be in place in the near future. Treatment of brackish water to produce drinking water also results in brine streams containing alkali salts that have to be addressed for proper disposal. This paper reviews treatment options for such streams containing high levels of total dissolved solids with emphasis on sulfate removal. Areas covered would be: a) chemical treatment for removal of various constituents that make up the total dissolved solids b) processes for sulfate removal processes –thermal and non-thermal-to recover and reuse of treated water and c) brine use and treatment options.INTRODUCTIONThe rising cost of water and meeting the ever-changing stringent environmental discharge regulations make water recycling and reuse essential. The metallurgical industry has used water as a medium for dissolving and/or rejecting metals and chemicals in addition to removing thermal energy. Any excess process effluent is collected and sent to end-of-pipeline treatment and ultimately discharged to surface water for disposal under a permit. The conventional- and probably the cheapest way -of treating metal-bearing process effluent streams is lime neutralization followed by sulfide polishing for elimination of heavy metals to produce a stream that meets NPDES discharge limits. This results in a stream containing dissolved solids.These dissolved solids normally comprises of inorganic salts. The possible constituents are cations calcium, magnesium, sodium and potassium. The anions are sulfate, chloride, fluoride, nitrate, carbonate and bicarbonate. In addition to these constituents, the treated effluent streams contain very small amounts of heavy metals, oxyanions such as arsenites, arsenates, selenites and selenates. Process streams from gold operations contain residual cyanide. Small amounts of ammonium ions are also present in these streams based on the pH of the solution."

Jan 1, 2012

By R. M. de Carvalho

Empirical and phenomenological models of SAG and AG mills have dominated the scene for the last few decades, being used nearly every time a mill is scale-up or an attempt is made to improve its performance. However, in spite of their success, these models fail to describe the details of both the grinding environment and the breakage mechanisms. The result is a generally good track record, with a few ? but very important ? instances when these models fall short in their predictions, which can be very costly. Further, nearly all of these models require detailed calibration to industrial and pilot plant data, being costly in their application, although still with limited predictive capabilities. Recognizing these challenges, a new model framework has been proposed which overcomes the limitations of currently used models by coupling the microscale population balance model, the discrete element model and functions that describe internal classification at the mill grate. This model framework has already been applied to describe breakage in ball mills, with showing very promising results. However, in the case of SAG and AG mills a much greater level of complexity is involved in the model, given the interaction between the mechanical environment that is formed totally or, in part, by the ore itself, and the breakage response in the mill. The paper describes the model framework, demonstrating how it can address appropriately effects such as mill speed, mill filling and size distribution, on the response from the mill. Some of the advantages of the model are related to its intrinsic multi-component and dynamic nature, which allows simulating appropriately mixtures of ores of different competences in a transient manner.

Jan 1, 2012

By Andreas Ludwig, Abdellah Kharicha, Menghuai Wu

"In order to demonstrate how CFD can help scientists and engineers to better understand the fundamentals of engineering processes, a number of examples are shown and discussed. The paper will cover (i) special aspects of continuous casting of steel including turbulence, motion and entrapment of non-metallic inclusions, and impact of softreduction; (ii) multiple flow phenomena and multiscale aspects during casting of large ingots including flow induced columnar-toequiaxed transition and 3D formation of channel segregation; (iii) multiphase magneto hydrodynamics during electro-slag remelting; and (iv) melt flow and solidification of thin but large centrifugal castings.IntroductionSince the Bronze and the Iron Ages, material processing, and here especially metallurgy, has got a global importance for the economic well-being of the societies. It is thus understandable that metallurgy has changed from arts and crafts into an engineering specialty, where the knowledge of centuries has lead to an enormous commercial and technical efficiency. However, increasing competition and the necessitation of energy and CO2 reduced manufacturing methods requires the improvement of existing techniques and even the development of new, alternative production technologies. On the other hand, the opacity of liquid and solid materials and the involved high temperatures makes the experimental penetration of metallurgical processes and with that the attainment of detailed process knowledge quite difficult."

Jan 1, 2012

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012

By Tom Gabardi, Peter Clarke

"MillMapperTM is a new 3D laser scanning technology that has only recently been introduced into the North American mining industry. It enables mill operators to gain a much more complete understanding of the condition of their mill internals and to more accurately predict how liners will perform in the future. This paper describes the technology and techniques used to obtain data on internal mill conditions, how this data is processed into meaningful information which enables better prediction of liner life and gives examples of the reports provided by the software. Examples are given, using client sites data, on how this information is being used to reduce the costs and improve the revenue from SAG and ball mills.INTRODUCTION Scanalyse Pty Ltd developed the MillMapperTM technology in Australia over a number of years and has recently introduced it into North America with a significant take-up in Canada. The technology was commercially released in Australia in late 2006 and there has been significant technical development in the features provided since that time. MillMapperTM has been accepted as a useful technology in the Australasian region and more recently has been introduced to sites in Chile, Peru, Brazil, USA, Canada, Laos and South Africa. Over 100 different mills have been scanned and the technology has been thoroughly tested and validated. It has become an integral tool in condition monitoring and improvement programs for SAG and Ball mills across many sites and is now providing significant and measurable benefits to the mining industry. Some of these benefits will be described in this paper using actual examples."

Jan 1, 2012

By Fernando Aracati Botelho, Jose Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud and about 800 kg of CO2 per ton of alumina. The direct use of exhaust gases to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing its reactivity and sequester from 3 8 to 107 kg of CO2 per ton of alumina. This paper shows a pilot scale reaction of a suspension of bauxite residue-water with flue gas produced from direct burning oil, similar to the exhaust gases of a refinery. Two different types of reactors are used, a spray tower and a packed column. The inlet and exhaust gases are analyzed using electrochemical cells and non-dispersive infrared sensors. The pH of the suspension is monitored during the reaction and after to evaluate the buffer effect. 2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0. 7 to 2.0 ton of the residue known as red mud (RM) per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reusing all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated [4]. In any case they will remain as an environmental passive and needs monitoring for decades. The search of a industrial process that combines the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of large scale and economically viable ways is the main objective of this work.The use of the exhaust gases of the refmeries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester millions of tones ofCO2 plus other gases like SO2 [7] and NOx. This project studies the reaction of the exhaust gases from a boiler burning diesel with RM in different reactor types and conditions in order to obtain parameters to design equipment capable of process this reaction on a larger scale. With these objective compositions of red mud were processed with flue gas at concentration similar to the exhaust gases of the calcination process and boilers of the refmeries."

Jan 1, 2012

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya

"This paper focuses on modeling of the scanning laser epitaxy (SLE) process that is currently being investigated and developed at the Georgia Institute of Technology. SLE is a laser-based manufacturing process for the creation of equiaxed, directionally solidified and single-crystal deposits of nickel superalloys onto superalloy substrates through melting and resolidifícation of alloy powders using a scanning laser beam. The thermal modeling of the system, done in a commercial CFD software package, simulates a heat source moving over a powder bed and dynamically adjusts the property values for consolidating CMSX-4 nickel superalloy powder. The associated melting and re-solidification process is modeled using an immediate consolidation approach, and the predicted melt depth is compared with the experimental data obtained. For a given position of the beam, geometrical parameters of the melt pool are used to estimate the resulting microstructure. The influence of the processing parameters on the microstructural evolution is also discussed. This work is sponsored by the Office of Naval Research through grants N00173-07-1-G031, N00014-10-1-0526 and N00014-11-1-0670.IntroductionIn order to increase the operating temperature of gas turbine aero engines, investment cast equiaxed turbine airfoils are now often replaced with airfoils that have either directionally solidified columnar or single crystal (SX) microstructure. Wear and damage during operation limits the lifetime of these components and necessitates the replacement of numerous airfoils within the engines. Due to the high cost of producing SX cast turbine blades, the cost of replacing each blade can be several hundred to several thousand dollars. With each engine containing several hundred blades, the cost to replace all blades can reach hundreds of thousands of dollars. Hence, it is of great interest to develop a process that can restore the single crystal microstructure at the locations of material loss and allow for the blades to be repaired and reused rather than be scrapped and replaced."

Jan 1, 2012

By Peter Bigwood

Whether drilling through tough clay or breaking rock, or facing the most severe conditions including mixed face ground, perched water and running and flowing sands, working under-ground certainly comes with no shortage of challenges. In an environment where the unknown is faced on a daily basis, tunneling contractors must be able to rely on their equipment to get the job done properly. Not only that, their equipment must comply with two of the highest priorities: safety and efficiency. In addition to being the number one concern, a proven safety record provides additional benefits to a company. A safe work environment serves as a key component to company growth, including the ability to remain competitive in bidding and maintaining higher-level, more challenging projects.

Jan 1, 2012

The gases transportation and adsorption in the coal are greatly dependent on the pore-crack parameters, such as the porosity, the pore distribution, as well as the number and size of the pores. What?s more, the pore parameters of the coal are always changing with the temperature. However, the pore characteristics and their changes are extremely difficult to quantify. In this case, Fractal Theory provides a good tool to address this issue. Based on this theory, the pore distribution coupled with the size of the pores can be quantitatively described. In this paper, the equation used to calculate the Fractal Dimension of coal pores was deduced and Mercury Porosimetry was employed to test the pores distributions of coal samples at different temperature. The experimental data excellently verified the Fractal characteristics of coal pores. In addition, the experiments also indicate that the Fractal Dimension of the coal pores linearly increases with the temperature.

Jan 1, 2012

By A. Jennings

[ ] In November 2005, Essroc Cement, part of the Italcementi Group, commissioned a long overland conveyor at their Nazareth plant in Pennsylvania. This conveyor, tagged CV-105, was designed to transport 1000 tph of limestone from the quarry to the kiln, and 400 tph of hot clinker (at 300°F) at back from the kiln to a handling facility about halfway back. Conveyor CV-105 is 8969 ft (2733 m) long. It gains 152 ft (46 m) of elevation in the first 1570 ft (480 m), then is mostly flat for the remaining 7400 ft (2250 m) (Figure 1). After the limestone is discharged at the head pulley, hot clinker is loaded onto the return side of the belt. This clinker can be discharged at one of two locations.

Jan 1, 2012

By Honggang Zhong, Tan Yi, Qijie Zhai, Zhao Dan, Xinping Mao, Huigai Li

"The influence of superheat degree on the distribution and volume content of inclusions were studied in 65Mn thin slab produced by compact strip production(CSP) in Zhujiang Steel in China, The results showed that the diameters of inclusions are mainly less than 5µm. Most of the inclusions gathered at the 1/4 thickness direction for the thin slab of 27? superheat degree, compared with the center position for that of 37?. There are more inclusions larger than 50µm in the low superheat samples, which is caused by the short floating time. In addition, the inclusions were observed and analyzed by metallurgical microscope, SEM and EDS in order to ensure their composition, type and further find their source. It was find that the types of these inclusions mainly are Al2O3, SiO2,CaO and their composites, a few of them are TiN and MnS.IntroductionIt is well known that inclusions have a great impact on the strength, plasticity, fracture toughness, cutting performance, fatigue property and corrosion resistance of steels. Especially, with the demand for thinner slab, the cleanness is increasingly becoming more significant as a quality criterion[1]. High manganese and carbon steels not only demonstrate high strength but also proper plasticity. There are many problems unsolved for 65Mn steel as a result of the low solidification rate, bad thermal strength, crack sensitivity and low casting temperature[2,3].The superheat of the molten steel has a great impact on the erosion of refractory lining, molten steel fluidity and non-metallic inclusion behavior[4]. The serious erosion situation of ladle lining, nozzle and casting tundish will give rise to more inclusions at a high superheat. Meantime higher superheat will make second dendrite arm spacing coursing and element segregation which lead to inclusion, bubble formation and shrinkage cavity. On the contrary, it is hard for non-metallic inclusions to float up with a low superheat value. Inclusions of 65Mn steel, which produced in different superheat condition by CSP, were studied for the sake of higher slab properties including statistics and EDS analysis."

Jan 1, 2012

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By T. Y. Yunsel

Estimation techniques such as polygonal, triangular prism, trapezoid, isopach maps, and inverse distance methods are often used in ore or industrial minerals deposit evaluation. These techniques do not express the variability of the deposit and do not allow a determination of the reliability of the estimates. However, geostatistical methods can express a measure of the error associated with the estimates, by finding weighting coefficients for a given mining block, and can also help with data configuration that minimizes the error. This work addresses an application study on the quality and reserve characteristics of the cement raw materials of the Adana Cement Factory in Adana, Turkey, based on the spatial distribution and variability of the chemical components (Si02, CaO, A1203, Fe203). The study has been carried out using a geostatistical procedure that is useful for site assessment, characterization, and monitoring situations where data are collected spatially. Directional and omnidirectional experimental variograms of the cement raw material variables showed that neither strong geometric nor severe zonal anisotropy exists in the data. The most evident spatial dependence structure expressing the continuity for omnidirectional experimental variograms were characterized by exponential and spherical variogram models. These models have been used in cross¬-validation analysis, which proved that these models, their parameters, and kriging parameters are applicable for the study area. Quality contour maps of the deposits at given levels underground were estimated using a kriging interpolation technique. Anomalies such as bullseyes and drift were not observed in the maps that were generated. Kriged maps showed the spatial distribution of quality continuity and variability of the deposits. Grade-tonnage curves and total tonnage estimates in the particular grade were determined using ordinary kriging in order to improve the mining operation and planning. Consequently, local uncertainty and the probability of extreme values occurring are tools of prime importance for the mine planning, the optimum mix of raw materials coming from different quarry stopes.

Jan 1, 2012

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By J. L. Hoover

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect bit drill wear and use the equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel Software. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012