Search Documents

By Reuben John Mathew

"Oxygen evolution is the main anode reaction in industrial copper electrowinning. The oxygen bubbles do not conduct electricity, thus increasing the electrolyte resistance. The oxygen bubbles formed at the anode rise to the surface, occupying a larger volume of the electrolyte at the top of the cell than at the bottom. This oxygen bubble concentration gradient contributes to a gradient in electrolyte resistance and consequently a tendency toward uneven current distribution. This phenomenon increases the chance for uneven growth on the cathode and/or short-circuits, particularly on the lower portions of the cathode. This issue may be ameliorated by increasing the charge transfer resistance for oxygen evolution down the height of the anode. This concept was studied by solving the current distribution for a 2-D model of a copper electrowinning cell using COMSOL.IntroductionA copper electrowinning tankhouse aims to operate at the highest current density that will deposit on the cathode a layer of copper metal possessing the desired physical and chemical characteristics. The operating current density is directly related to the physical nature of the copper deposit on the cathode (Figure 1), limiting a copper electrowinning tankhouse to some operating current density that produces acceptable copper deposits.[!] The ratio of the operating current density to the limiting current density is typically around 0.3.[2] If the limiting current density for a cell could be raised, the operating current density could also be raised and thus result in savings in capital cost for a tankhouse. [3]The average operating current density in a copper electrowinning plant is 270A·m- 2 .[4] The value for average current density, however, obscures the fact that the face of a cathode does not experience this value equally. Indeed, the current density varies along the height of an electrode and is independent of the height of the electrode.[5] This phenomenon partly explains why the lower portions of a cathode tend to display a rougher copper deposit.In order to utilize a higher operating current density but still remain at 30% of the limiting current density, the limiting current density must be raised, but it is affected by the mass transfer regime at the electrodes. The mass transfer regime is currently poorest at the lower portions of the cathode and this is part of the reason for the tendency for poor cathode deposits to occur at the lower portion of the cathode.[6]"

Jan 1, 2012

By H. Kinilakodi

The authors previously developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the safe performance index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the health and safety risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency or the U.S. Mine Safety and Health Administration (MSHA) in recognizing and addressing emerging problems with actions that may have been able to predict high-risk conditions, the fatality and/or other serious injuries. The approach would have given extra scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By Michael Wortley

Metso?s Process Technology and Innovation group is a world leader in mineral processing consulting. A significant amount of this consulting work involves process integration and optimization (PIO) studies, which include investigating the effects of drill-and-blast design and implementation on downstream processing. Critical to these studies is the ability to track specific ore into, and through, the plant. To increase the accuracy of this ore tracking, Metso Process Technology and Innovation (PTI) developed a system to track ore using a radio frequency identification (RFID) transponders technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and, finally, into the concentrator. The system is called SmartTag. Since its commercialization in 2007, SmartTag has been used in the majority of PTI?s consulting projects, and several permanent systems have been installed worldwide.

Jan 1, 2012

By John Hickey

Management teams at mining companies begin to ask themselves whether to take a company public and, if so, how to do it as they approach the normal threshold for going public in terms of revenue and operating performance. Today, the expense of going public generally suggests the company has at least $20 million in annual revenue and at least $2 million in cash. The revenue number can be lower for mining companies with large reserves. In order to properly attract the investing public, the company must also be operationally strong with robust prospects. The company should have a strong management team and a consistent history of double-digit growth that will continue into the foreseeable future. Assuming the thresholds are met, a company?s management needs to weigh the pros and cons of going public.

Jan 1, 2012

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By O. Guyot, A. Broussaud, M. Revalor, G. Legrand, D. Kok, E. Roux

"The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance.The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness.The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock™ rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill™ system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase.The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones."

Jan 1, 2012

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By D. J. de Clerk

Global trends stipulate the need to optimize existing assets while reducing environmental impacts. This paper illustrates the procedure that was followed to achieve such goals at one of the coal burning flash dryer units at an Anglo American smelter. An in-depth study of the process and related literature led to the development and installation of a revised control philosophy. This system includes modifications to the existing regulatory control structure as well as a hybrid rule-based and model-predictive advanced process control (APC) layer. Since commissioning of the APC, this flash dryer?s average throughput has increased by more than 6%, despite higher feed moistures. Furthermore, even though coal consumption has increased slightly, operating efficiency has improved by close to 5%. This was made possible by improving stability of the drying column outlet temperature by approximately 40%, which in turn enabled selection of a more optimal setpoint. Recent data has shown that APC utilization now exceeds 95%. This is indicative of a successful controller installation with good site acceptance. The same philosophy has therefore since been rolled out to most of the other flash dryers in the group.

Jan 1, 2012

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

By B. Caro Vargas

The Toulon Tunnel project is a key component of the highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960s. The tunnel project is comprised of two separate tunnels: south and north. The north tunnel was built between 1992 and 2002 after 10 years of difficult construction. On March 15, 1996, for example, a collapse of the tunnel in the Marchand area generated a sinkhole in the city center, causing a 20-month delay. The south tunnel alignment runs parallel to the north tunnel below Toulon?s historical downtown at a depth of 20 to 40 m (65 to 131 ft) with some areas with less than 10 m (32 ft) of cover. The risk management program was studied to be a state of the art program in urban tunneling construction.

Jan 1, 2012

By A. Mitchell

On 25 August 2011, Andrew Mitchell, Lucas Moalusi, and Matthew van der Want of Bell Dewar hosted a presentation on Mining and Communities in Mooinooi, in the North-West Province. The conference was attended by traditional leaders in the North-West Province, officials from the Department of Local Government and Traditional Affairs, and executives from the mining industry. The presentation concerned traditional governance in mining, communities? rights in terms of applicable legislation, and the corporatization of community affairs.

Jan 1, 2012

By M. Abumiya, N. Onodera

"The synthesis of large scorodite particles in non-ferrous metallurgical industries usually requires a high-cost operation involving heating and high-pressure autoclaving. To overcome these obstacles, an atmospheric-pressure process for scorodite synthesis (DMSP®) was developed, in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. This process gives scorodite of good crystallinity with particle sizes as large as 15-20 µm. The solutions used for scorodite synthesis in the DMSP® are prepared from various residues containing arsenic from non-ferrous smelters. The solutions may be contaminated with Cu, Sb, and Bi, for example, and therefore the effects of such impurities on the formation of crystalline scorodite need to be investigated. In this study, the effects of Cu, Sb, and Bi contaminants on the formation behaviors of scorodite particles in the DMSP® were investigated systematically.INTRODUCTIONThe synthesis of crystalline scorodite (FeAsO4·2H2O) is a suitable method for arsenic (As) stabilization and storage of As-containing by-products such as flue gas dusts in non-ferrous smelters. It is expected that the formation of large, highly-crystalline scorodite particles would be an ideal method for avoiding the release of arsenic to the environment. Generally, autoclave methods under pressurized oxidation conditions at temperatures above 100°C have been used for the formation of arsenic minerals such as scorodite. However, the autoclave method requires sealed vessels that are resistant to high pressure, heat and acids. This process is also unfavorable on account of the high construction expenses, and high running costs as a result of vapor heat loss. Processes for synthesizing scorodite under atmospheric conditions at temperatures below 100°C which do not need an autoclave have therefore been extensively investigated (Demopoulos, Droppert, & VanWeert, 1994; Demopoulos, 1996; Demopoulos, Lagno, Wang, & Singhania, 2003; Droppert, Demopoulos, & Harris, 1996; Filippou & Demopoulos, 1997).Recently, Fujita et al. (Fujita, Taguchi, Abumiya, Matsumoto, Shibata, & Nakamura, 2008a, 2008b, 2009; Fujita, Taguchi, Kubo, Shibata, & Nakamura, 2009; Fujita, Taguchi, Shibata, & Nakamura, 2009) developed a new method for producing large scorodite crystalline particles with improved filtration and washability properties at normal atmospheric pressure and temperatures below 100°C. In the new method, oxygen gas (O2) is blown into solutions containing a high concentration of arsenic ions (As(V)) and ferrous ions (Fe(II)). The Fe(II) ions were subsequently oxidized to ferric ions (Fe(III)), resulting in the formation of large scorodite particles. High supersaturation of solutes such as Fe(III) will result in excessive nucleation, and the formation of poorly crystalline phases. The scorodite formation must therefore be conducted in a manner that avoids the critical supersaturation level being exceeded. It is supposed that the oxidation of Fe(II) to Fe(III) by O2 gas in the new method suppressed the supersaturation of Fe(III) during scorodite formation. The low Fe(III) supersaturation resulted in formations of highly crystalline scorodite particles of size of around 20 µm. In June 2008, based on the developed process described above, DOWA began experiments to verify the industrial capability of a plant with a capacity of 30 MT/month of As. It was successfully proven that it is possible to produce crystalline scorodite industrially on a commercial scale. This process was named and trademarked as DMSP® (Kubo, Abumiya, & Matsumoto, 2010)."

Jan 1, 2012

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By S. Koski, M. Schmalzel, D. A. Jacobson, S. Crosby, P. Cook, M. Mular

"Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product.The MP1250’s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint."

Jan 1, 2012

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

By F. Lombard

We consider in this paper the use of a modified version of Hotelling?s statistic in the analysis of particle size distributions. The statistic can be adversely affected by the presence of outliers among the data. We propose a competitor to the statistic that is based on ranks, and hence is less sensitive to outlier effects. The results of a Monte Carlo study suggest that the rank test is highly competitive with the Hotelling test in its ability to detect differences between two mass size distributions. The calculation of the rank statistic is explained in detail and its application is illustrated on two sets of data.

Jan 1, 2012

By Edouard Asselin, Guikuan Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe( II )-Fe(III)-H2S04 solution at 25°C and 70 °C. Results from the calculation ofspeciation in the above solution reveal that, at both 25 °C and 70 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller values for the reversible potential of the ferric/ferrous couple based on the Nemst equation. Exchange current densities of the ferric/ferrous couple were obtained by extrapolating the cathodic linear Tafel line to the reversible potential and are on the order of 10-7·10-6 A/cm2 at 25°C and 10·6-10-5 A/cm2 at 70 °C, respectively. The transfer coefficients were about 0.35-0.38 at 25°C and 0.35-0.45 at 70 °C. Polarization plots of CPC and CPP under different nominal Fe3+/Fe2+ ratios are in good agreement at 25 ·c and at 70 °C. Based on the obtained exchange current densities, the rate constant k, was calculated and is on the order of 10-1 cm/s at 25 °C and 10 1 cm/s at 70 °C.IntroductionChalcopyrite is the most abundant copper mineral in nature, accounting for about 70% of copper reserves in the world [I]. In recent years, the metallurgical industry has been searching for a hydrometallurgical process as an alternative to pyrometallurgical treatment due to high emissions of S02 and capital costs associated with smelting. Activity in this area has increased recently due to some inherent advantages associated with hydrometallurgical processing, such as the possibility of treating low-grade ores (increasingly more abundant in the case of copper) and easier control of waste, with the attendant benefits to the environment [I]. Chalcopyrite is highly refractory under most hydrometallurgical conditions, owing to the formation of an anodic passivation layer on the chalcopyrite surface which renders the process kinetics very slow. Most of the currently proposed processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Sulfuric acid is preferred over all other leaching reagents in terms of cost, environmental friendliness, and ease of its regeneration during electro-winning. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale,"

Jan 1, 2012

"Some of the tools developed for the processing of nickel laterite ore by resin-in-pulp (RIP) may be applicable to the remediation of metalliferous mine drainage (MMD). In both cases, recovery of metal value and production of a stable waste stream appropriate for long term storage is desired. MMD typically has the additional challenge of management of toxic low-value metals. Seen in this light, innovations in RIP reactor configuration, selective elution strategies and novel synthetic ion exchange resins become useful tools for taking on the MMD challenge in a way that maximizes both environmental and economic benefit. INTRODUCTIONAcid mine drainage (AMD) is a common problem in any country with significant past mining activity. When sulphide containing minerals, tailings or slag are exposed to water, oxygen and sulphur oxidizing bacteria, AMD will result. Abundant and reactive iron sulphide minerals leach first, providing acidity and the ferrous/ferric couple that can enhance the oxidation kinetics of other minerals. If this runoff contacts encounters acid consuming carbonates or silicates, the acidity may be neutralized, but certain heavy metals remain in solution and can continue to be an environmental hazard (Gray, 1997). For this reason, the remainder of this paper will refer to the broader term metalliferous mine drainage (MMD) rather than acid mine drainage. In either case, such drainage, containing high heavy metal concentrations and often significant acidity, is toxic to aquatic life and can lead to significant damage to ecosystems and to public watercourses. MMD is a problem most commonly associated with now defunct sulphide mineral mines, but similarly toxic streams can result from many types of waste, such as poorly stabilized leach tailings, slag heaps, and coal flotation tailings (Johnson and Hallberg, 2005; Lee et al., 2002; Sainz et al., 2002; Schüring et al., 1997). In any case, the management and remediation of MMD is an important ongoing problem for the resource industry, particularly for the many mines in Canada closed before the advent of more stringent environmental standards. MMD remediation represents a significant long term expense for the resource industry. Multi-disciplinary efforts to understand and mitigate this problem range from creation of artificial wetlands (Poulin and Lawrence, 1996; Sheoran and Sheoran, 2006) to sophisticated biochemical reactors and precipitation processes (Hatami, 2010). Certain remediation technologies such as ion exchange offer methods to make a saleable product by recovering valuable dissolved metals. This paper will show how these technologies can help defray the cost of remediation, and offer potential to turn a dangerous waste stream into a useful product."

Jan 1, 2012