Search Documents

By Alan D. Hartman

Standard metering of electric arc furnaces usually uses root mean square (RMS) or true root mean square (TRMS) measurements for determining power. Only sinusoidal signals are accurately described by RMS meters, and dc or high-frequency components normally are lost in standard TRMS metering. This can lead to inaccuracies when electrical signals are not sinusoidal, contain dc components, or include fast risetime perturbations, as is the case with the electric signals from an electric arc furnace. Electric arc furnace electrical waveforms, observed in research carried out by the U.S. Bureau of Mines, show high-frequency components and significant deviations from sinusoids. These perturbations and distortions make metering difficult for standard power meters. The inaccuracies in metering can cause further problems if those sensors are used in control systems. For control strategies requiring rapid response, any averaging scheme loses information that can be used in control decisions. In order to obtain better signals for both monitoring and control, a study of instantaneous, RMS, and TRMS power monitoring devices was conducted. From this study it was concluded that precision integrated circuits should be used to obtain instantaneous power with a bandwidth of at least 25 kHz. The information from these devices is more representative than that of standard meters and can be used in predictive control.

Jan 1, 2010

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By B. M. Das

Several laboratory model test results for the determination of the ultimate uplift capacity of single and group metal piles embedded in near-saturated clay have been presented. Based on the uplift test results for single piles, the variation of the adhesion factor with the undrained shear strength of clay has been determined, and an empirical correlation for estimation of the adhesion factor in soft and medium clays has been presented. The group efficiency of piles under uplifting load depends on factors such as embedment ratio, undrained shear strength of clay, the number of piles in a group, and the center-to-center spacing of the piles.

Jan 1, 2010

By P. Mikhailik

Recently, characterized by fast development high- and nano-technology, demand for rare and trace metals has increased. One of such metals is gallium. Gallium compounds, mainly GaAs, are used in medicine, to manufacture optoelectronic devices, microwave techniques, devices of solar power and infrared optics, etc. The basic gallium industrial deposits are known only on land. There are bauxites (50 ppm), nepheline rocks and ores (36-38 ppm, minerals concentrators are nepheline and sodalite), Zn-Pb-Cu ores (5000-12000 ppm, minerals concentrators are gallite, germanite, sphalerite, bornite), sulphide-polymetallic and Pb-Zn ores (10-32 ppm, minerals concentrators sphalerite, chalcopyrite) (Vershkovskya et al., 1998). High concentration of gallium are observed in hydrothermal massive sulphides of a Mid-Okinawa Trough (The South Chinese Sea) and Sujo seamount (The Philippine Sea) (Noguchi et al., 2007). As it is known, deep-sea massive sulphides and associated Fe-Mn crusts are products of hydrothermal fluid discharge. High-temperature massive sulphides precipitation are the first, and low-temperature Fe-Mn crusts deposition is the last process of hydrothermal mineralization (Cronan, 1982). Hydrogenic crusts and nodules of the World ocean are characterized by low concentration of Ga, close to clarke (19 ppm) (Kobaltbogatye.., 2002). Hydrogenic crusts from the Sea of Okhotsk are exception, because Ga concentrations are exceeded clarke in 3,5 times (Mikhailik, et al., 2009). Complex studying of Fe-Mn crusts from deep-sea basins volcanic seamounts of the Sea of Japan has shown their hydrothermal-sedimentary genesis (Mikhailik, 2009). High gallium concentration (up to 850 ppm) was established in these crusts by ICP-MS (Agilent 7500C). Microprobe research (JXA-8100) of samples Fe-Mn crusts has not revealed the gallium minerals concentrators. It suggests that, gallium in Fe-Mn crusts of the Sea of Japan is sorb substance.

Jan 1, 2010

The surface of chalcopyrite was studied in situ in aqueous solution by an atomic force microscopy (AFM). The AFM images showed that some absorbate in patches was detected on the mineral surface, after the chalcopyrite sample was soaked in 5x10-4M potassium ethyl xanthate (KEX) solution at pH 11 for 10 minutes. These patches increased in size with time elapsing. At the same time, as shown by the obtained AFM force curves, the adhesion between the AFM tip and the substrate increased greatly due to the adsorption. Rinsing with ethanol removed the absorbate from the chalcopyrite surface, as well as the big adhesion observed in KEX solution.

Jan 1, 2010

By T. Gollaher

The use of paste thickeners for mineral tailings has gained increasing acceptance by the mining industry throughout the world and in the U.S. during the last five years. Advantages of water recovery and environmental sustainability are the driving forces for paste as an alternative to conventional thickening and the slurry pond. This paper presents a summary of the differences between paste and conventional tailings thickeners, along with recent examples of full-scale paste thickener installations.

Jan 1, 2010

By Mark Jolly

"Instead of using the traditional batch casting process, the CRIMSON [1] (Constrained Rapid Induction Melting Single Shot Up-Casting) method employs a high-powered furnace to melt just enough metal to fill a single mould in a closed crucible. The crucible is transferred to a station for computer-controlled counter gravity filling of the mould for optimum filling and solidification. The CRIMSON method therefore holds the liquid aluminium for a minimum of time drastically reducing the energy losses attributed to holding the metal at temperature. With the rapid melting times achieved, of the order of minutes, there isn’t a long time at temperature for hydrogen to be absorbed or for thick layers of oxide to form. The metal is never allowed to fall under gravity and therefore any oxide formed is not entrained within the liquid. Thus higher quality castings are produced leading to a reduction in scrap rate and reduced overall energy losses.IntroductionEngineers at the University of Birmingham, England, with local company, NTec, have invented a new casting process that will reduce the energy costs of light-metal foundries. The technology, entitled CRIMSON, means that foundries need only heat the quantity of metal required to fill a single mould rather than large batches that use unnecessary energy and create waste. The complete concept of CRIMSON requires a change of philosophy in the approach to casting and requires the user to think holistically in order to reap the full benefits from the process. This paper will discuss the various aspects of energy wastage within the foundry sector and discusses the processes whereby the energy can be reduced. Primarily the author focuses on the aluminium sector but CRIMSON can be applied to many of the non-ferrous “light” alloys. Ferrous materials and non-ferrous “heavy” alloys can also benefit from some of the ideas but not necessarily directly from the application of CRIMSON."

Jan 1, 2010

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

By H. R. Shen

Cushion materials are one of the most important links in an efficient piling system. In the past, little has been done in China on this problem, so engineers are still used to those traditional woods, papers and coir ropes. In this paper, the SOA of piling cushions, their testing method and parameters used in wave equation analysis for piling are briefly reviewed. The static and dynamic mechanical characteristics of 3 types of cushion material have been determined in laboratory and suggestions about testing method and evaluation of test results are given.

Jan 1, 2010

By Valeri Mitkov

Studena Quarry is one of the main suppliers of inert materials for concretes production in Sofia. It is characterized by massif heterogeneity in density and fissuration. Failure to take into consideration this fact during the planning of the blasting works recently had unsatisfying results in their carrying out – obtaining of materials with too small dimensions or high percentage of outsize material. Series of test blasting were carried out to find the relations for calculation of the main parameters of the drilling and blasting works. The blasting network was enlarged to 6 x 6 m, the diameter of the shot-boreholes was changed from 110 to 152 mm, the stem of the boreholes was significantly reduced and the relative consumption of blasting agents as a whole was reduced to 0,37 ?g/m3.

Jan 1, 2010

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By Adam Stremcha, John MacGregor

Initial planning called for 3 separate drop shafts and 3 separate vent shafts to be pulled back from the excavated tunnel with a large diameter raise bore machine. With time constraints and the raise bore machine already in high demand on other shafts, a more “traditional” drill and blast approach was taken on a few of the larger drop shafts. This decision proved to be not only cost effective, but also reduced schedule impact as the shafts were excavated simultaneously with the other raise bores.

Jan 1, 2010

By P. K. Narasimhargahavan

This paper discusses briefly the major reasons associated with the growth and its impact on the energy requirement and Environmental imbalance. A projection based on the present global Alumina and Al requirement indicate a substantial further growth of at least 30% over the next 10 years. It is indicated that the main factors which are likely to influence investments are the environmental factors such as the Climate Change and global response to the growing energy prices and sustainable development. Each of the developed / developing nations must find response to the GHG emissions which will encourage the Al Industry to make an effective contribution to global warming while preserving the international competitiveness of the industry - a challenging task. The efforts shall concentrate on improving energy efficiency in the industry possibly of the order of 25% over the next 10 to 20 years. The developments in this line are discussed.

Jan 1, 2010

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the theory of sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of along chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals, and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even lognormal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2010

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

By Marvin B. Thompson

"The depositional model for major Illinois Basin coalbeds is well documented and defined on a regional scale. The model was a driving force during past exploration for lower sulfur and thicker coal deposits. The most attractive coal reserves were known to lie along the flanks of contemporaneous sandstone filled stream channels and were overlain by thick silty gray shale roof. At various distances away from the channels, the depositional model transitioned to black shale I limestone roof, sulfur content of the coal bed increased, and the coal bed often thinned. Understanding the character of roof rock types associated with this depositional model is essential to predicting ground control factors on both a regional scale, and on resolving roof control problems at the mine-site. Additionally, horizontal stress and overburden depth are significant factors that impact roof rock quality and ground control in Illinois Basin mines.Determining the character of several rock types, and defining the primary horizontal stress direction were crucial to a recent successful project at New Future Mine, located in southern Illinois. An inclined slope was constructed from the Illinois No. 5 Coalbed up to the Illinois No. 6 Coalbed through strata that ranged from extremely weak ""stackrock"" and a weak underclay unit, to a massive sandstone unit. Engineering geology, operations management, and Jennmar technical services personnel teamedup to select and install roof support for each strata transition. The project was completed with no injuries and no roof falls.INTRODUCTIONAbundant published information concerning coal deposition, geographic distribution, quantity, quality, and mining conditions exists for Illinois Basin coal reserves. The State of Illinois, through its State Geological Survey (ISGS), has provided decades of research, record keeping, and service to the coal industry. Other excellent sources of Illinois Basin coal information include the Indiana Geologiq1l Survey and the Kentucky Geological Survey. Past research by the U.S. Bureau of Mines (USBM) supplemented the work by the geological surveys, especially in the area of horizontal stress and mining hazards. The National Institute for Occupational Safety and Health (NIOSH) continues to produce publications focused on roof control issues common to many coal basins, including the Illinois Basin. Many of the illustrations in this paper originated in ISGS and USBM publications."

Jan 1, 2010

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies which strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 300 m. The mining method is a variation of planar open stoping. Pillars are widely employed to support the open stopes. In the deeper levels, in-stope pillars are required to fail in a stable manner soon after being cut, and the residual pillar strength is used to stabilize the hanging wall. These pillars are commonly known as crush pillars. Little work has been done in the past to determine pillar peak and residual strengths, and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to over and undersize pillars with consequential loss of ore, pillar bursts and potential collapses. This paper describes a crush pillar design methodology, and provides design charts. Three mining environments were incorporated in the investigations, which included underground and laboratory measurements, analytical solutions, numerical model sand back analyses. The results of the study are suitable for the areas where the research was carried out, and may also be applied with caution in other similar environments.

Jan 1, 2010