Search Documents

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

By Klaus Schwerdtfeger

The rules of solution of oxygen from H2O-H2-He gas and of nitrogen from N2-H2 gas in shallow melts of liquid iron were measured at 1610o and 1600o C, respectiuely. Concentration profiles were detemined in the liquid iron. Tire rate data indicate that the solution process is controlled by diffusion in the iron melt. The diffusivities for oxygen and nitrogen in liquid iron, as calculated from the present data, are DFe-o = (12 ± 3) < 10-5 sq cm per sec and DFe-N = 11 ± 2) X 10-5 sq cm per sec at the temperatures employed. AN attempt was made by Shurygin and Kryukl to measure the diffusivity of oxygen in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was measured. Assuming that the rate of dissolution of silica is controlled by diffusion of oxygen in the iron, the oxygen diffusivity was computed from the rate data giving Dfe-0 = 6.1 X 5 sq cm per sec at 1600°C. Although this value seems to be of the right order of magnitude, there is no proof of the correctness of the assumptions involved in the interpretation of these rate data. The oxygen concentration in the iron at the iron-iron silicate interface was taken to be that in equilibrium with the silica-saturated silicate melt. That is, it was assumed that no concentration gradient existed in the liquid silicate. This is a questionable assumption, unless it is proved that the thickness of the silicate layer is very much smaller than that of the diffusion boundary layer in the iron. Furthermore, Shurygin et al.1 used the Levich equation2 to interpret their rate data. This equation was derived for mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich&apos;s derivations. In the present work the diffusivities of oxygen and nitrogen in liquid iron were measured at 1610" and 1600oC, respectively. EXPERIMENTAL METHOD Iron melts contained in high-purity gas-tight alumina crucibles were reacted with H2O-H2-He gas for the determination of the oxygen diffusivity and with N2-H2 gas for the determination of nitrogen diffusivity. At the end of the reaction period, the samples were quenched in a cold H2-He gas stream at the top of the furnace. Oxygen or nitrogen contents in the iron were determined by chemical analysis. Two different types of diffusion experiments were perforxed. To determine concentration profiles, a few rate measurements were made using 4-cm-deep melts. The solidified samples were sliced into discs and each disc was analyzed for oxygen or nitrogen. In another series of experiments, oxygen or nitrogen was diffused into shallow melts (about 0.5 to 1 cm in depth) and the total sample was analyzed to obtain an average concentration of the diffusate. In most experiments, 4- to 5-mm-ID alumina crucibles were used. Some experiments were also made in smaller (3 mm) and larger (7 mm) diam crucibles. This variation in diameter caused no difference in the reaction rate, within the limits of experimental uncertainty. To promote the establishment of a stable density profile in the melt, all the samples were suspended in the lower end of the hot zone so that the top of the melt was hotter by a few degrees. Molybdenum wire resistance heating was used. The reaction tube of the furnace was a gas-tight recrystal-lized alumina tube. In most experiments the furnace was heated by an ac power supply. To check the possibility of inductive stirring, some experiments were carried out in a dc operated furnace, with essentially the same results. The temperature of the furnace was controlled automatically in the usual manner. The temperature was measured with a Pt/Pt-10 pet Rh thermocouple and is estimated to be accurate within ±5°C. The iron used was prepared by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zir-conia crucible. The main impurities are: Si 0.004 pct P, S <0.002 pct Cr 0.005 pct N 0.001 pct Zr 0.002 pct O 0.003 pct Mn 0.004 pct C 0.002 pct The gas composition was controlled by constant pressure head capillary flowmeters. Oxygen was removed from the gas mixture by passing it through columns of platinized asbestos (450°C) and anhydrone. Selected H2O contents were obtained by passing the purified gas through oxalic acid dihydrate-anhydrous oxalic acid mixtures held at constant temperature in a water bath. Water vapor pressure data for the oxalic acid dihydrate-anhydrous oxalic acid equilibrium were taken from the 1iterature.3 The flow rate used was about 1.5 liters per min. The whole system was checked for tightness at regular intervals.

Jan 1, 1968

By R. J. Schaefer, M. E. Glicksman

Direct, in situ observation of metallic alloys during solidification reveals that in some systems crystal multiplication occurs by means of a dendrite remelt-ing process, without the necessity of independent nu-cleation events. The solidification is observed on optically clean surfaces of supercooled molten alloys. In one system (Sn-3 wt pct Bi) , a fine-grained equi-axed structure is produced by the complete disintegration, via remelting, of transient initial dendrites. In contrast, several other metallic systems show little or no evidence of remelting activity. The behavior of these metallic systems is consistent with that expected on the basis of published observations of dendrite remelting in transparent organic alloy systems. It is concluded that dendrite remelting is an important crystal multiplication process in some metallic alloys, but is velatively unimportant in some other alloys. The detachment of dendrite branches from the primary stem by a remelting process has been observed by Jackson, Hunt, Uhlmann, and seward1 during the solidification of some transparent organic alloy systems. The branches released by this remelting process can drift free of the primary stem and serve as seeds for the formation of numerous independent crystals. This proliferation of new crystals does not require repeated independent nucleation events, but only modification of the initial solidification structure. The mechanism of dendrite remelting, as described by Jackson et a1.1 and by Tiller and O&apos;&apos;Hara,2 is dependent on the transport of both heat and solute and is, therefore, expected to operate only in alloys, and not in pure substances. It was found in the transparent organic alloy systems that remelting occurred primarily in the constricted regions near the base of dendrite branches, where the branches had grown through the solute-rich liquid layer surrounding the primary dendrite stem. It was suggested that impure solid had formed in these constricted regions at a relatively low temperature and had later become unstable as further solidification of purer material raised the temperature. Jackson et al. proposed that the equiaxed zone of metal alloy castings originates from a similar remelting process, and they demonstrated the operation of this mechanism in "ingots" poured from saturated salt solutions. Although these substances were especially selected to show solidification behavior similar to that of metals,3 the remelting mechanism has, until now, been subject to the objection that its operation has not been directly observed in a metallic system. Considering the fact that thermal properties such as diffusivity may differ by as much as two or three orders of magnitude between metals and organic compounds, this objection was considered to be possibly serious. A method has now been developed by which it is possible to make direct optical observations of metals during solidification. This method has revealed transient solidification processes which would not be detected by metallographic examination of totally solidified specimens. In particular, a grain-refinement process in a metallic alloy has been observed to be a direct consequence of the total disintegration of an initial dendritic structure. The influence of an initial, transient solidification structure on the final solidification structure is demonstrated here for the first time in a metallic system. I) EXPERIMENTAL The technique of using a transparent flux to maintain an optically clean metal surface during solidification has been described by us elsewhere.* The

Jan 1, 1968

By O. D. Sherby, J. L. Lytton, C. R. Barrett

Randomly oriented polycryslalline copper of 99.995 pcl was tested in tension at temperatures of 626o, 496o, and 406o. The gvain-size mnge investigated was from 0.03 to 0.7 mm. Grain sizes were produced by two techniques: 1) varying the amount of prior cold work and the amealing time at constant annealing temperature so as to obtain various vecrystallized grain sizes with minimum grain growth, and 4 holding the prior cold work constant while varying the annealing time or temperature so as to obtain varying grain sizes by grain growth. Polycrystalline samples (grain size of 0.03 mm) with a strong. [001](100) texture were also studied. The relationship between the steady-state creep rate, Es, and pain size was found to be the same indepentent of the technique used to prepare the various grain sizes. For specimens with grain diameters above about 0.1 mm ea zuas esse)ztiallj~ independent of grain size, while for smaller grain diameters Cs increased slightly with decreasing grain size. Strongly textured polycrystalline copper, which contained low-angle grain boundaries, exhibited steady-state creep rates that were slightly lower than those observed in randomly oriented copper, of the same gain size. The results are explained by conside?%ng- the contribution of grain boundary shearing to the total strain and the effect of grain size on the resulting creep substructure. EXPERIMENTAL observations concerning the influence of grain size on steady-state creep rates are varied and oftentimes conflicting. Numerous early investigators found that an increase in the grain size resulted in a decrease in the high-temperature steady-state creep rate, i,.&apos;-" Other workers have foundthat ef decreases with increasing grain size up to some optimum grain size and then increases with a further increase in grain size.&apos;- &apos;&apos; It has been suggested that es, decreases with an increase in grain size only because the range of grain sizes studied normally lies to the left of the grain size for optimum creep resistance. However, sherbyl2 and Feltham and his co-worker13, 14 have found that even for small grain sizes 2, does not always decrease with an increase in grain diameter but may be proportional to the square of the grain diameter. A possible explanation for the different creep rate-grain size relationships which have been observed is that in most experimental studies different grain sizes have been prepared by annealing at various temperatures. For metals in which the impurity concentration is high (greater than about 0.1 at. pct) this type of

Jan 1, 1968

By G. B. Gibbs

Various semiempirical equations which relate defect-formation energies and entropies with elastic and thermal properties of a metal crystal are shown to be related by a simple model for lattice energy. An illustrative comparison of theory with experiment is made using self-diffilsion data for fee metals. SEVERAL workers have related the free energy of defect formation with elastic and thermal properties of a crystal lattice, particularly elastic bulk modulus and Debye temperature. The present note shows how the various approaches are related by a simple model for lattice energy. A comparison of theory with experiment is given using the self-diffusion parameters of fee metals. 1) A MODEL OF THE CRYSTAL LATTICE The internal energy per atom in a metallic lattice may be written U=Ui-Ue [1] where Ui and Ue refer to ion-ion interaction and valence electron energies, respectively. The volume per atom V has an equilibrium value 52 for which

Jan 1, 1968

By A. Grant Elliot, H. W. Lavendel

qualitative picture has been developed to describe the oxidation behavior of TaSi2-coated tantalum and CbSi2-coated columbium. These systems have a significantly lower inherent oxidation resistance than MoSi2-coated molybdenum does. This stems primarily from the fact that Ta2O5 and Cb2O5 are nearly as stable thermodynamically as SiO2, whereas MoO2 or Moos are not. Further, diffusion of silicon in the Ta- and Cb-Si system is considerably slower than in the Mo-Si system. These ,factors prohibit the mechanism of selective oxidation of- silicon which accounts for the oxidation resistance 01- MoSi2-coated molybdenum. The silicide can be stabilized by adding suitable Modifiers which increase the thermodynamic stability of the silicate formed during oxidation. Modifiers, such as aluminum, can be inroduced into solid solution in the coating. in controlled amounts through proper selection of the source in the pack cementation process of coating fov~rzatiorz. Addition of aluminum to TaSi2, coatings on tantalum was effective in moderately increasing the oxidation resistance. EXTENSIVE experimental work and analysis have established the nature of the oxidation behavior exhibited by MoSi2- and MoSi2 -coated molybdenum-base alloys, and defined the conditions for maximum protection against oxidation of the substrate.&apos;-* The oxidation resistance of MoSi2 in the temperature-pressure range of 1100°C-PO2 > 10-5 atm to 1900°C— PO2 > 10-1 atm is due to the formation at the surface of a continuous film of SiO2 which results from selective oxidation of silicon. Under the prevailing kinetic conditions, this film is stable toward the molybdenum silicide with which it comes in contact. Initially molybdenum oxidizes also, but it forms volatile species. SiO2, however, nucleates and grows as a condensed phase. Once a continuous film of SiO2 has formed, the oxidation rate falls to that observed for the oxidation of pure silicon indicative of diffusion through the oxide film as the rate-controlling mechanism. This oxidation behavior is of course highly dependent upon temperature and oxygen pressure. Bartlett and Gage13 and Bartlett, McCamont, and Gagelb define precisely this dependence in terms of the oxygen partial pressures and silicon diffusivities required to support a stable SiO2 film. At low temperatures (near 500°C—the "pest" region) silicon diffuses too slowly to be selectively oxidized. Hence, molybdenum and silicon oxidize readily in proportion to their stoi- chiometry. At high temperatures and low pressure, SiOz dissociates to form volatile SiO(g), and a protective film cannot be maintained. Application of the MoSiz/Mo system is limited to temperatures below 1900oC, the eutectic between MoSi, and MO5Si3.5 The oxidation behavior of MoSi2-coated molybdenum is essentially the same as that outlined above with the exception that the MoSi2 is not in equilibrium with the molybdenum substrate. At the temperatures under consideration silicon will diffuse rapidly into the molybdenum eventually converting the coating to MosSi3.4 The rate constant for subsequent decomposition of Mo5Si3 into Mo3Si plus silicon, and/or the diffusivity of silicon through Mo3Si then becomes low enough to allow active oxidation of both molybdenum and silicon with subsequent degradation of the specimen. A stable silica film can be formed but at temperatures and/or oxygen partial pressures higher than those required with MoSi2 present as a source of si1icon.l, 4 Because of the similarity between the silicides of molybdenum and those of columbium and tantalum one would expect similar oxidation behavior for coatings in the respective systems. This is not entirely the case, however, as shown by the experimental results reported herein. Regarding tantalum and columbium disilicide coatings on tantalum and columbium substrates, respectively, the oxygen arriving at the surface of the coating partitions itself nearly equally between the metal and the silicon, and a two-phase oxide layer (Me2O5 plus SiO2) is always formed. The diffusion of silicon in the tantalum and columbium silicides is relatively slow, compared to that in the molybdenum silicides, which further enhances this equipartitioning of oxygen. Thickening of the coating during service by inward diffusion of silicon into the substrate is correspondingly slow, and the effective thickness of the coating at the roots of cracks and defects is only slightly changed providing high probability for premature coating failure. Furthermore, the SiO2 glass that is generated is not thermodynamically stable with respect to the coating. The metal silicide tends to reduce the SiO2 liberating either free silicon or SiO. The situation can be improved by suitably modifying the coating such that the stability of the protective glass which is generated during service is increased. Thus, selective oxidation of silicon and the modifying agent will occur, and the silicide coating will not tend to reduce the oxide layer. Modifying agents can be introduced into the coating by the pack cementation process. Using sources containing the modifier at controlled chemical potentials allows control of the coating composition. Partially substituting aluminum for silicon in TaSi2 coatings by forming a Ta(Si,Al)2 solid solution was effective in moderately increasing the oxidation protection.

Jan 1, 1968

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5&apos;7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By T. F. Bower, M. C. Flemings

The classical explanation for formation of the fine equiaxed "chill zone " in ingot solidification is that local supercooling near the chill wall causes copious nucleation in this region. This work indicates, however, that convection is an essential element in formation of the chill zone. In the absence of convection, no chill zone forms even though rate of. heat extraction is extremely vapid. Alloy studied was Al-l.5 pct Cu alloy solidified against a copper chill wall. When solidification was initiated at the chill wall in absence of. cor-vection, surface grain size was large (>I cm diam). When it was initiated in the presence of convection, it was fine (<0.05 cm diam). It is concluded that some form of "crystal multiplication" plays an important role in formation of the chill zone. INGOT macrostructures are generally classed as containing one or more of the three zones: "chill zone", "columnar zone", and central "equiaxed zone". These three zones are sketched in Fig. 1; their origin has been discussed in some detail.&apos;-&apos; The classical explanation for formation of the chill zone is that supercooling occurs in the region of liquid metal adjacent the mold wall, and copious nu-cleation then takes place in this region forming numerous small crystals. The columnar region then results by growth of favorably oriented grains (den-drites) which crowd out their less favorably oriented neighbors."5 The mechanism of the columnar-equiaxed transition has been the subject of considerable interest. The generally accepted mechanism, until recently, was that constitutional supercooling developed in front of the growing columnar grains with eventual nucleation of new, equiaxed, grains ahead of the growing solid front.&apos; Recently, it became evident this explanation was not completely satisfactory and it is now evident that "crystal multiplication" plays an important role. This crystal multiplication occurs by separation of dendrite arms from growing dendrites,8?"&apos; and has been shown to be strongly influenced by convection.6, 10-13 Reduced convection results, for a given alloy, in longer columnar zone, larger columnar grains, and larger equiaxed grains.7, 12

Jan 1, 1968

By G. F. Bolling

Single crystals of each metal were deformed at 77°K and heated at constant rates, variously in the range 0.125" to 4o°Kper min from 77" to -390oK, while being monitored in an X-ray diffractometer. Changes in diffraction-peak heights and line breadths were used to ascertain the temperature ranges of recrystalliza-tion. The results were subjected to the analysis of nicholas&apos; in order to obtain the rate-controlling activation energies,Q. In this analysis no recourse to a separate and distinct nucleation stage is required and the results of studying recrystallization proved consistent with the hypothesis of a constant number of nuclei or equivalent hypotheses. The values Pb = 5.5 ± 0.5 keal per mole Zn ~ 7.5 Sn - 5 Bi - 9. 5 correspond for lead, zinc, and tin to activation energies obtained elsewhere for grain boundary migration, and for bismuth and lead to previous studies of re-crystallization by Barrett.6 This correlation allows the conclusions that interference from recovery was minimal and that the observed recrystallization rates in these pure metals are effectively governed by grain boundary migration. Good agreement was not found between the results of this kind of study in zone-refined aluminum and previous work; and supplementary isothermral experiments involving hardness tests and metallography did not resolve the discrepancy. Nevertheless, at least a range,Q = 11.5 ± 2 keal per mole, can be assigned to the activation energy for boundary migration in aluminum. An experimental study of one aspect of the recrystallization process is presented here for four metals of different crystal structure. The metals chosen for study were all zone-refined to reduce impurity effects, but the attendant high purity presented a difficulty. For any reasonably high driving force a "re-crystallization temperature", TR, is in the range of 0.25 T,, where T, is the absolute melting point, and study was therefore restricted to lower temperatures. An X-ray technique under constant heating-rate conditions adequate above 90°K was devised for the study; in consequence, a newer type of analysis following Nicholas1 had to be used to obtain quantitative information about activation energies. The standard methods of studying recrystallization have involved the comparable analyses of Johnson and Mehl2 and Avrami3 which are reviewed by Burke and Turnbull.* The general analysis4 which is applied only to isothermal studies using any of various investigative techniques states:

Jan 1, 1968

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.&apos;" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long &apos;&apos;fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By W. J. Babyak

The habit planes for hydride precipitation in large grains of alpha zirconium and Zircaloy-4 were determined in specimens containing 161 and 136 ppm hydrogen, respectively. In zirconium, the hydride platelets precipitated on various pyramidal planes inclined to the basal plane at angles ranging from 10 to 50 deg and 75 to 90 deg. Hydrides were most frequent at inclinations of about 20 deg and 90 deg. In Zircaloy-4, hydride plates were inclined to the basal plane at angles vanging from 5 to 25 deg with the predominant inclinatioiz equal to 12 deg; no platelets were found near the prism plane position. In both zircoinium and Zir-caloy-4, hydrides were principally, but not exclusively, parallel to (1011) type planes. When the Zircaloy-4 gmins were subjected to tension stresses of 12,100 psi and 19,400 psi during hydride precipitation, the hydride habit was unchanged except that precipitation favored those habit planes which were inore nearly perpendicular to the stress direction. The stress-orientatioiz effect increased with the magnitude of the stress. THE hydride habit plane in a zirconium has been determined by several investigators. Langeron and Lehr1 in 1956 found platelets parallel to (1010) slip planes. In 1962, Westlake and Fisher2 confirmed these findings and showed that hydride precipitation on twin planes, as reported by Kunz and Bibb,3 was probably due to incomplete removal of worked metal from specimen surfaces. Secondary habit planes, ( 1011) and (1015), were also found by Westlake and Fisher under particular charging conditions where a hydride layer may have existed at the hydrogenation temperature. Most recently, walters4 and westlake5 again observed the (1010) habit exclusively in zirconium. Louthan and hgermans have reported that hydrides precipitate on various ( 101l ) and (112l) planes positioned 31.5 to 90 deg to the basal plane in Zircaloy-2. The present investigation was concerned with the hydride habit in Zircaloy-4 in relation to that in zirconium and the possible change in habit when precipitation occurs under stress. The latter consideration was prompted by the stress-orientation phenomenon originally reported by Marshall and Louthan.7, 8 I) EXPERIMENTAL Materials and Specimens. Chemical analyses of all materials are given in Table I. The zirconium specimen was a 1 by 4 in. section cut from wrought crystal bar that was hot-rolled at 790°C to 0.300 in. and cold-rolled to a final thickness of 0.095 in. All surfaces were mechanically polished and then chemically polished with a solution of H2O, HNO3, and HF (10:10:l by volume) prior to annealing. Grains as long as 0.25 in. were grown by thermally cycling the specimen three times (in 10-5 mm Hg vacuum) between 825" and 1000°C at approximately 125°C per hr. The specimen was isothermally annealed at 825°C for 24, 40, and 120 hr after each cy-

Jan 1, 1968

By K. Mukai, M. Ishihara

This report is a brief discussion of the impurity levels both in primary aluminum and super-purily alnminim in connection with raw materials and proc-essing methods. Particularly, truce amounls of im-purities were analyzed by introducing nittss-speclro-gruphy and nenlron-aclivalian analysis techniques. Vanadium and gallium content in primary aluminum metal corresponded to theor amounls in anode coke. but the nickel content in primary aluminum was hide-pendent oj its amount in the anode cake. Sulfur in the anode colic might result in an increase of the iron content in the molten metal in the reduction cell. The content of sodium and calcium increased with increasing bath ratio. In the holding furnacc sodium content decreased rapidly, and nonmetallic inclusions merit separated front the mollen metal. Three-layer elctrolysis was effectire in eliminating many impuri-ties with the exception of copper, aluminum oxide. aluminum nitride, and some rare-earth elements. THE amount of impurities and nonmetallic inclusions in aluminum metal depends on impurities in the raw materials and various production processes. This paper presents an investigation of the behavior of impurities and nonmetallic inclusions in aluminum during the electrolysis process, the period in the holding furnace, and the process of three-layer electrolysis. Chemical analysis and emission spectrometric analysis have generally been used as methods to determine small amounts of impurities in both primary aluminum and super-purity aluminum; however. mass spectrography and neutron-activation analysis have been recently introduced into this field, and trace amounts of impurities can accurately be determined by these latter methods. EXPERIMENTAL WORK Common impurities were determined by means of absorptiometric. polarographic, flame-photometric. and emission-spectrometric methods. However, in the determination of trace amounts of impurities and non-metallic inclusions, the following methods were applied. In the analyses of trace impurities by mass-spec- trographic analysis, samples were exposed in the vacuum spark of double-focus ing Mattauch-Herzog type mass spectrograph (Japan Electron Optics Laboratory, Ltd.). Ilford Q2 photographic plates were used as ion detectors. Fe was used as the internal standard, and the atomic concentration of each element was calculated by the following expression and converted into the weight concentration: where E, and Ei are the exposures (coulomb) when isotopes of the internal standard and impurity elements (on which the estimate is based) show the same density, X is the percent (atomic) concentration of the standard, IF and Ii are the percent abundances of the isotopes of the standard the impurity elements (on which the estimate is based), and Ms and hfi are the mass of the isotopes of the standard and impurity elements (on which the estimate is based). The coefficient of variation in this method is about 40 pct in the range of 0.1 to 1 ppm. In neutron-activation analysis, irradiations were done in the nuclear reactors TRIGA-I1 (neutron flux: 4.7 x 10 11 n per sq cm per sec; Rikkyo University) or JRR-2 (neutron flux: 2 x 1013 n per sq cm per sec: Japan Atomic Energy Research Institute). After the chemical separation, a NaI (3 by 3 in.) scintillator connected to a 256-channel y-ray spectrometer (R.C.L.) was used for counting and recording various activated impurities. The coefficient of variation in this method is about 20 pct. In the analyses of nonmetallic inclusions, aluminum-oxide determination was carried out according to Fischer&apos;s method, 3 as follows. A slice of sample was cut off and the surface was cleaned. It was dissolved in bromine-methanol. The solution was filtered and the residue was washed. The residue was fused with potassium bisulfate flux. Then it was dissolved in weak acid, and oxine solution was added. The aluminum oxinate was extracted with benzene. Finally, aluminum was determined absorptio-metrically. Aluminum nitride determination was carried out as follows. A slice of sample was cut off and the surface was cleaned. It was put in the distillation apparatus and decomposed with sodium hydroxide solution. The solution was distilled. Then ammonia was absorbed and

Jan 1, 1967

By R. T. Southin

Cast ingots of 99.99 pct purity A1 and aluminum/copper alloys containing up to 2 pct Cu have been found to contain four zones rather than the three previously accepted, i.e., chill, colummar, and equiaxed zones. The fourth zone consists of a coarse dendritic layer across the top surface of the ingot which is open to the atmosphere. It is also found that the grains in the equiaxed region have a "cornet" shape, with a head which is coarsely dendritic and a tail which grew with the same structure as the columnar grains. Experiments using mechanical barriers, and others involving the elimination of the surface dendrile layer, have indicated that nucleation of the equiaxed zone is caused by the showering of dendritic particles from this surface dendrite layer. These particles are the dendritic heads found in the comet grains. A mechanism of nucleation and growth of these comet grains is put forward. Experiments with a number of other metals and alloys suggests that these conclusions may apply generally to ingots cast without the addition of nucleating agents, and solidified under normal conditions. THE macrostructure of cast ingots may contain the following three zones: i) a peripheral zone of fine equiaxed grains, commonly called the chill zone; ii) a zone of columnar grains extending inwards from the chill zone; iii) a central zone of equiaxed grains; these are normally larger than the chill grains. All three zones are not necessarily present in any particular ingot since their existence and magnitude depend upon the casting conditions and composition of the cast material. The mode of formation of zones i and ii is fairly well understood. However, the cause of the central equiaxed zone remains a matter of conjecture. Previous theories put forward to explain the mechanism of nucleation in the equiaxed zone have been examined by Chalmers1 and Winegard.2 At the time when the present work was carried out the most re -cent hypothesis was that due to Chalmers,1 who recognized more fully than previous workers that conditions in this zone during solidification were not conducive to nucleation. In his hypothesis, he suggested that nuclei were formed near the mould wall during the very early stages of solidification, and that they can drift into the central zone by convective motion. This was supported by evidence from experiments using mechanical barriers to stop the drift of nuclei. A similar hypothesis had previously been put forward by Genders.3 More recently, Jackson et al. 4 have observed that dendrite arms in organic compounds can melt off during solidification. They have postulated that this occurs in metals and alloys, and that the dendrite arms which have been freed from the main dendrite act as nuclei for the equiaxed zone. In the present work, critical metallographic examination has shown that there is a fourth zone in the macrostructure of cast ingots which is a dendritic layer over the top surface of the ingot. It is also shown that there is a relationship between this zone and nucleation of the equiaxed zone. EXPERIMENTAL DETAILS The alloys examined were prepared from super -purity aluminum of 99.99 pct min purity (spectro-graphically detected impurities of Cu, Fe, Si, and Mg) and copper of 99.98 pct min purity (spectrographically detected impurities of Si, Zn, As, Fe, Pb, Bi, Ni, Sn, Mn, Ag, Cr, and Al). Three compositions of ingots were examined, containing 0.0, 0.1, and 2 pct Cu, respectively. The alloys were melted in an alumina-lined salamander crucible using a medium-frequency electric induction furnace; when the appropriate casting temperature was reached, the alloys were cast without degassing or fluxing treatment. The mould used was made of electrode graphite and had the following dimensions: external diameter 6 in., height 9 in., with a mould cavity 8 in. deep and a diameter tapering from 5 in. at the top to 4 in. at the bottom. Casting temperatures used were generally in the order of 70" to 90°C above the liquidus and the mould was at room temperature before casting. Inserts kere placed in the mould cavity in some experiments. These consisted of either an 18-g stainless-steel tube of 2 in. diam held axially in the mould i in. off the bottom and extending 1 in. out of the top of the mould or a "trap-door" barrier of stainless-steel gauze of 24-mesh held horizontally in the mould 31/2 in. down from the top. The construction of this insert is shown in Fig. 1. All inserts were preheated prior to casting to prevent chilling. RESULTS The macrostructures of ingots of the three compositions are described, in terms of the three generally recognized zones, in Table I, and illustrated in Figs. 2(a) to (c). The most interesting observation in this table is that relating to the shape of the equiaxed grains, which were not in fact equiaxed but of almost tear-drop shape. Closer examination of these grains showed that each consisted of a head which had a coarse dendritic structure and a tail which always grew in the opposite direction to heat flow, and which had the same structure as that of the columnar material of the ingot concerned; i.e., in the pure aluminum and 0.1 pct Cu alloy it was cellular and in the 2 pct Cu alloy it was cellular-dendritic. Identification of original cast grains was greatly hampered in the super-purity aluminum ingots, and to a lesser degree in the 0.1 pct Cu alloy,

Jan 1, 1968

By Norman Brown, J. V. Rinnovatore

Substructures in explosively deformed and annealed ß brass have been examined by electron microscopy. In the explosively deformed condition, the structure contains a large density of straight screw type dislocations. Subsequent annealing up to 300oC produces low angle boundaries, which are characterized by superlattice dislocations, and expanded and contracted nodes. Evidence is given where two a(111) superlattice dislocations combine to form two a(001) superlattice dislocations. It is also shown that annealing at 400°C the networks disappear and that quenching from 400" C produces square and circular prismatic dislocation loops that lie on (100) and (111) planes, respectively. THE purpose of this work was to determine the effects of explosive deformation and subsequent annealing in a superlattice using electron microscopy. One of the first observations of explosively deformed structures was made by Hornbogen1 on a iron. Hornbogen found that screw dislocations were most prominent in the explosively deformed structure. He explained this result by suggesting that the edge components of dislocation loops move with the velocity of the shock front leaving a trail of extended screw components. Kressel and Brown2 observed explosively deformed Fe3A1, which is basically a body-centered type of superlattice in terms of dislocation geometry, and found that, as in the case of iron, screw dislocations were most prominent. It was also observed2 that, in cold-rolled and explosively deformed nickel, screw dislocations did not predominate, but rather a uniform network of dislocations was present in which the orientation of the dislocations was random. (Cell structures also have been observed by Nolder and Thomas3 for copper and by Johari and Thomas* for nickel). Kressel and Brown2 discussed the difference between dislocation morphology for bee and fee metals in terms of dislocation mobilities. They suggested that edge dislocations have a greater mobility than screw dislocations in bee metals but not in fee metals. Thus, the idea offered originally by Hornbogen1 is not valid since it should apply equally to fee and bee systems but does not. The results of recent work by Mikkola and cohens on explosively deformed Cu2Au are consistent with other observations for fee metals. They found that dislocations were randomly arranged but there was no significant cell formation. At high shock pressures, deformation twins are produced in fee metals.&apos; High pressures in bee metal should induce the bee — fee transformation while the metal is under pressure. EXPERIMENTAL PROCEDURE The Cu-Zn alloy used in this work contained 51.4 wt pct Cu. Specimens of 0.5 in. diam and 0.012 in.

Jan 1, 1968

By J. Gurland, A. Gangulee

The cracking of silicon particles embedded in an aluminum matrix occurs progressively over the range of plastic deformation of the composite specimen. The fracture probability of the particles increases with increasing particle size and decreasing silicon contents. The crack orientation tends to be perpendiculay to the direction of the maximum tellsile strain. An example of a direct association between matrix slip and particle cracking is shorn. ALUMINUM-SILICON alloys of commercial compositions fail by ductile fracture in three stages:&apos; I) initiation of cracks in the silicon particles, 2) growth of cracks into cavities, and 3) rupture of the aluminum matrix separating the cavities. The present work is concerned with the first stage: the initiation of cracks in the silicon particles. EXPERIMENTAL PROCEDURE Aluminum samples with 2.8, 6.1, 9.6, and 13.2 vol pet Si, respectively, were cast from commercial al- loys. Machined tensile specimens (2 in. gage length) were annealed in air at 1000°F for 100 hr, and then pulled at a strain rate of 0.025 per min. The grain size (average linear intercept) of the aluminum matrix was 0.24 and 1.6 mm in the 6.1 and 13.2 pet Si alloys, respectively. The particle size of silicon in alloys of one composition (6.1 pet Si) was varied by either modifying the castings with 0.15 pet Na or prolonging the annealing time. The average particle size was measured by linear and planar analysis, assuming spherical particles of uniform size. The particle sizes and compositions of all samples are tabulated in Fig. 8, together with the identifying symbols used in the graphs. The respective numbers of broken and unbroken silicon particles were determined from metallographically prepared longitudinal sections by counting a total of approximately 2000 particles per sample. EXPERIMENTAL RESULTS 1) Crack Initiation During Deformation as Function of Composition. Nominal stress-strain curves of four specimens of different compositions, but approximately equal particle sizes, are presented in Fig. 1. The fraction of broken particles, P (no. of broken particles/ total no. of particles), is shown in Fig. 2 as function of true stress and in Fig. 3 as function of nominal strain. The last point of each composition line in Fig. 2 rep-

Jan 1, 1968

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of&apos; heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker&apos;s Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.&apos; At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

By William C. Hagel

Oxygen-18 exchange between gaseous oxygen, held at a pressure of 125 mm Hg in a PL-IORh chamber, and splzeres of a Fe2O3 containing three or less grains was determined from 9000 to 1250°C. Isotope equilibrum on crystal surfaces appears to be quickly established, and the rate-determining factor is self-difiusion confbvrning to the relation D = 2.04 esp(- 77,900/RT) sq cin sec-&apos;. Changing sphere diameters caused no detectable variation in diffusion coefficients. Oxygen ions diffuse faster than cations at low temperatures, but a crossover may occur at about 1150°C. INVESTIGATIONS by Davies et al.&apos; and Himmel et al2 have suggested that the mechanism of iron oxidation above 600°C involves a predominance of cation migration in the wüstite (FeO) and magnetite (Fe301) layers and oxygen-ion migration in the hematite (a Fe2O3) layer. Evidence for little cation migration during hematite growth consists of: 1) the disappearance of radioactive-silver markers, presumed to vaporize from the oxide-gas interface, and 2) a large discrepancy between parabolic rate constants for magnetite oxidation and those calculated from Lindner&apos;s3 data for cation self-diffusion, D:, using Wagner&apos;s theory.4 Reversing the calculations gave anticipated self-diffusion coefficients, D:, for oxygen ions of 3.6 x 10-9 sq cm sec-1 at 1100°C and 5.9 x 10-10 sq cm sec-1 at 1000°C. Since then Kingery et a1.5 reported three values for oxygen-ion diffusion in polycrystalline, sintered hematite. These were obtained near 1200°C, at an oxygen pressure of approximately 150 mm Hg, and could be represented by the Arrhenius expression, Dg = 1 x 10 11 exp(-146,000/RT) sq cm sec-1. Extrapolation to temperatures below 1100°C infers that oxygen ions are less mobile than cations. This contradicts the aforementioned oxidation evidence and also coble7s study of the initial sintering of hematite. From the latter, apparent diffusion coefficients for the slowest rate-controlling species could be calculated, and fair agreement was found with an extension of Lindner&apos;s data for cation diffusion. Fig. 1 depicts such comparisons graphically. Three points have been included for the determinations of Himmel et al. on cation diffusion in large, natural hematite crystals surrounded by pure oxygen at atmospheric pressure. No dependence on crystal log raphic direction was noted. Since the value of 10-l4 sq cm sec-&apos; at 1000°C actually represents an upper limit, one might interpret that there is a small decrease in D: when single crystals are employed. On the whole, however, cation diffusion appears relatively well-defined,* while the few results tension to lower temperatures. After having gained experience measuring oxygen-ion diffusion in certain glasses7 and in the corundum oxide, a Cr2O3, the purpose of this work was to determine D; values for hematite and thus possibly assist a mechanistic understanding of the kinetics of the oxidation and reduction of solid iron oxides. I) EXPERIMENTAL PROCEDURE A) Material. Hematite powder of moderately high purity was received from the Columbian Carbon Co. An accompanying lot analysis listed 0.03 H2O, 0.008 weight percents, with the remainder Fe2O3. Subsequent treatments were ball milling, drying, prepressing, and hot-pressing for 60 min at 1350°C under 5000 psi. Since graphite dies coated with a slurry of alumina were used for hot-pressing, the surrounding atmosphere at temperature was sufficiently reducing to form some magnetite on the outer surface of each cylinder. After removing any attached alumina, a stabilizing anneal of 50 hr at 1300°C in oxygen was added. The final product was nonmagnetic and exceeded 97 pct of the density (5.24 g cm-3) usually given for FezO3. On polishing cylindrical ends, counts were made of the number of grain boundary intercepts per

Jan 1, 1967

By Clark L. Corey, Bogdan Lisowsky

Electrical resistivity, X-ray line positions, degree of order, and microstructures have been investigated for Ni-A1 alloys near the Ni3Al composition. The results indicate that Ni3Al undergoes disordering between 1250oC and the mp; also supersaturated y, produced in y + y&apos; alloys by gas quenching, is extensively ordered prior to y&apos; (Ni3Al) phase separation. The latter reaction, if not both, must follow the cooperative phenomena model. Shifts in line position as a function of quench-indulced super satulration are shown. Lattice pavarneters of equilibriunz and nonequilibrium phases are given. THE objective of this investigation was to determine the mechanism and kinetics of the reactions which occur in Ni3A1 and hypostoichiometric Ni3A1 alloys. The results are of particular significance relative to pre-precipitation phenomena. Early work on Ni-A1 binary compositions near the Ni3A1 composition (13.6 wt pct Al) has been adequately reviewed by Hanssen,1 whose phase diagram is presented in Fig. 1. williams2 verified the suggestion made by Taylor and Floyd3 and others4 that y&apos;, Ni3A1, may precipitate coherently on (100) planes of the y phase (see Fig. 1 for phase nomenclature); he further suggested a two-step precipitation mechanism consisting initially of probably short-range ordering followed by actual precipitation of y&apos;. The precipitation stage in low-aluminum hypo-eutectic compositions has been studied by a number of investigators;*"7 short-range order or "zone" formation have been suggested as explanations for various diffuse X-ray scattering effects. The ordering reaction in Ni3A1 alloys is characterized by a) a very rapid rate of ordering in nonstoi-chiometric compositions, b) absence of a disordered phase region for the stoichiometric compound, y&apos;, or Ni3A1, c) precipitation phenomena as a dominant aspect in hypoeutectic alloys, and d) an increase in elec-trical resistivity on ordering.&apos; The latter two factors were found by Newkirk to characterize ordering in Co-Pt, for which an extensive and detailed analysis was made.&apos; An electrical-resistivity increase on ordering has also been reported for cuAu3.10 PROCEDURE Ni-A1 alloys in the form of 1300-g chill-cast ingots were prepared by vacuum melting electrolytic nickel and high-purity (99.99 pct) aluminum. Very small heats prepared from high-purity carbonyl nickel, supplied through the courtesy of Dr. Goff of the Naval Research Laboratory, were used for comparison with the larger ingots and no differences were noted. The cast material was homogenized in purified argon for a minimum of 72 hr at 1200°C and water-quenched from 1350°C. Compositions studied are given in Table I. The 10 pct A1 alloy was both hot- and cold-rolled. X-ray superlattice line intensities and peak positions were obtained from -270 mesh filings, using CuK, radiation with a LiF crystal monochromat adjusted to receive both 01 and a2. One-degree slits and a 1/8 deg per min scan rate were used to record line traces. A standard tungsten powder, obtained through the courtesy of G.E. Research Laboratory, was used to calibrate line positions.

Jan 1, 1968

By R. T. Torgerson, W. A. Baginski

Alloying studies were conducted on modifications of Cb-10W-1OHf (C-129) alloy as part of a cooperative alloy development effort between The Boeing Co. and the Wah Chang Corp. The purpose of these studies was to develop a fabricable, high- strength columbium alloy with superior melding properties. The initial investigations of alloy modifications were conducted using laboratory-melted button ingots. An alloy with the composition exhibited excellent veld ductility, elevated-ternpevature strength, and fabricability. The yttrium-modified alloy was desigrzated C-129Y and was selected for further developrnetzt. Three prodziction heats of C-129Y weve processed into sheet. Welding, forming, and tensile proper-lies are presented for this material. Tungsten-are welds of. C-129Y exhibited a minimum bend radius of 1/2T in the as-welded conditioti compared to 8T for C-129 alloy. An investigation was conducted on Disil coating of C-129Y and test data are presented on oxidation resistance and effects of re-entry environments. The excellent combination of strength, fabricability, weldability, and low transition temperature of C-129Y alloy offers potential design advantages for use of this alloy in structures of aerospace vehicles. It is atiticipated that C-129Y will rapidly supplant C-129 and similar alloys clue to the versatility provided by its impvoved welditzg properties. COLUMBIUM alloys with improved properties are required to achieve better performance and efficiency of radiation-cooled structures for re-entry vehicles and recoverable launch systems. Cooperative work by The Boeing Co. and the Wah Chang Corp. resulted in the development several years ago of C-129 alloy, a high-strength Cb-W-Hf alloy.&apos; This alloy has received favorable consideration for many advanced designs of high-temperature structures due to its excellent combination of properties. However, this alloy exhibits low weld ductility unless given a high-temperature stress-relief treatment. For this reason the development effort was directed towards modification of the C-129 alloy composition (Cb-1OW-1OHf) to eliminate the need for post-weld heat treatment. This paper describes the successful development of an alloy meeting this requirement. This new alloy was designated C-129Y and has a nominal composition of EXPERIMENTAL PROCEDURES Alloying Studies. Various Cb-W-Hf compositions were investigated using are-melted button ingots. These buttons were hot-forged using a protective glass coating and rolled into sheet specimens. Metal-lographic examination: tensile testing, and welding studies were conducted to evaluate properties of the experimental alloys. Sheet Fabrication. Three pilot production heats of C-129Y were fabricated into sheet to establish processing techniques and to determine sheet properties. The three heats consisted of 6-in.-diam ingots weighing from 140 to 250 lb. The ingots were prepared by electron-be am melting followed by vacuum-arc melting. The hafnium and yttrium additions were made during the are-melting operation by tack welding alloy strip additions to the Cb-W master-alloy electrode. The final ingots were machined into billets with samples of the machine turnings collected for chemical analysis. Ingot breakdown methods for the three heats are as follows: Ingot Ingot Heat Size Weiaht___Breakdown Method A 6 in. 250 lb Hot extrusion B 6 in. 140 lb Hot forging C 6 in. 250 lb Hot extrusion Sheet bars from the extrusion and forging operations were conditioned, recrystallized, and rolled into sheet. Initial rolling was conducted at elevated temperatures and final rolling was conducted at room temperature.

Jan 1, 1967

By E. Buehler, R. H. Willens

A Hew melting technique has hem adapted to the rapid quenching of- alloys from the liquid state. The inelting method has no limitations on the alloys investigated for there is no reaction with crucible materials and the most refractory materials are easily melted. The vate of heating is so rapid that alloys which have a high vapor pressure constituent can be melted with a minimal loss in material. Several new superconductovs have been discoveved by vapid quenching of lolten alloys. THE rapid quenching of alloys from the liquid state has led to the discovery of many new metastable phases. The methods initially used were limited to alloys which did not react with crucible materials.1,2 There was also the unmentioned limitation in tem- perature. Alloys with melting points much greater than 2000°C could not be melted in the rapid-quench apparatus. Recently, there have been successful attempts to rapidly quench reactive alloys by Moss et at. and Matthias Moss et al. injected powdered material (325 mesh) into a high-temperature plasma and the high-velocity molten droplets impinged on a cooled copper plate. The technique innovated by Matthias was to melt the alloy in an arc furnace and splatter it against a copper plate by means of a high-velocity gas jet aimed at the melt. I) FAST COOLING APPARATUS The creation of a metastable phase in a given alloy system by rapid cooling from the melt is contingent on the quenching rate. Some alloys require very slow rates while other alloys require the ultimate in quenching rate. At the present time, the vertical-gun technique of Duwez and willens&apos; has demonstrated, in practice, the highest quenching rates and thus the best

Jan 1, 1967