Search Documents

By Guy N. Bjorge, A. J. M. Ross, S. J. Staple, J. D. Johnson, J. F. Wiggert

In recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No. 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B. & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Furthermore, assurance of safety and uninterrupted operation required two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent. Plans for New Shaft The B. & M. shaft, begun in 1878 before much was known of the form and extent of the orebodies, was too near the ore and was endangered by ground movement. In 1924 this shaft was seriously threatened and sinking of the B. & M. No. 2 shaft, to supplant it, was begun. The latter was completed to the 1550-ft. level in 1928. In the meantime ground movement at the B. & M. shaft had practically stopped and, though loss of the shaft constantly threatened, ore hoisting was con-

Jan 1, 1937

By Earl F. Hanson

Fires in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of $61,996,719. General Layout of the Mine The No. 2 shaft, which is the main working shaft of the Tintic Standard, is within the main orebody and is connected with the five other shafts. Their respective positions with respect to the No. 2 shaft are as follows: North Lily, 2770 ft. northwest with drift connections on the 700 and 900-ft. levels; No. 3 shaft, 670 ft. east connected through the 700-ft. level; Eureka Standard, 4550 ft. south, connected on the 900-ft. level; No. 1 shaft, 1470 ft. southwest, with connecting drifts on the 900 and 1250-ft. levels; Eureka Lilly, 2000 ft. southwest, with connecting drift and raise through the 1250-ft. level. The Tintic Standard orebody consists essentially of one continuous oreshoot extending from the 600-ft. level to the 1450-ft. level, with a cross-sectional area of approximately 70,000 sq. ft. at both top and bottom, reaching a maximum area of 215,000 sq. ft. between the 1100

Jan 1, 1937

By Walter S. Weeks

The process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. Case I If compressed air is allowed to expand to the atmospheric pressure through an orifice in an air line that is supplied by a running compressor, no cooling results except the negligible one due to the JouleThompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected. Symbols P1 Absolute pressure in pipe line, lb. per sq. ft. P3 Atmospheric pressure, lb. per sq. ft. V1 Volume occupied by 1 lb. air in pipe. V3 Volume occupied by 1 lb. air at P3. C, Specific heat of air at constant volume, B.t.u. per lb. per deg. F. C, Specific heat at constant pressure, B.t.u. per lb, per deg. F. T1 Absolute temperature of air in pipe, deg. F. T8 Absolute temperature of air outside after expansion and mixing and coming to rest. j Mechanical equivalent of heat (778 ft. lb.) R Gas constant for air, ft-lb. per deg. F. = 53.3. Formulas Consider 1 lb. of air moving out of a pipe. The air behind it does work on it to the extent of P1V1 ft-lb. This work is really done by the thrust of the piston of the compressor and does not come from any energy that exists in the air in the pipe. The pound of air contains

Jan 1, 1937

By J. William Fehnel

The health hazard due to the inhalation of certain dusts in the mining industry has been recognized, but was not subject to state or federal inquiry in the United States until about 1916. Reports on miners' phthisis and associated effect of dust inhalation were published as early as 1903 in South Africa and in 1906 in Australia. A report was made by Lanzal in January 1917 of a study of 433 cases of miners' consumption among zinc miners in southwestern Missouri. In a preliminary report issued in 1915 Lanza and Higgins2 concluded that, while there were general causes, such as housing and working conditions, that tended to produce a high incidence of tuberculosis, the flint dust constituted an unusual element of danger, to which it was reasonable to attribute the unusual prevalence of tuberculosis. Later a clinic established under the joint sponsorship of the United States Bureau of Mines, the mine owners, and the Metropolitan Life Insurance Co. carried on an extensive study covering a period of five years. The results of this study have borne out the conclusions reached in the earlier surveys. The early surveys in this country indicated the necessity of determining the extent of the dust pollution of air associated with the various mining operations. The first determinations were reported on the weight basis, undoubtedly to make comparisons with work previously done in Australia. Later studies of dust in industry led to the development of more refined methods of sampling and enumeration on the basis of count in place of weight, so that by 1919 Knowles3 reported 53 methods.

Jan 1, 1937

By R. S. Archibald, L. S. Chabot

The Blueberry mine is about 10 miles west of Ishpeming, Marquette County, Michigan. The property consists of about 2000 acres in sees. 3, 4 and 5, T. 47, N.R. 28W. and secs. 32, 33 and 34, T. 48, N.R. 28W., and, excepting one intervening 80-acre tract, contains the iron formation for a length of about 21/4 miles. The property is traversed by State Highway M-28 and is served by three railways, the Chicago & Northwestern, the Duluth, South Shore & Atlantic, and the Lake Superior & Ishpeming. The Northwestern transports the ore to a dock at Escanaba; the other railways, to Marquette. Ore for Chicago goes via Escanaba and that for Lower Lake ports, as Detroit, Cleveland, and Buffalo, via Marquette. History The presence of iron formation in this property has been known for many years, and mining operations on a small scale have been carried on intermittently. The Dexter mine, on the SE.1/4 of the NW.1/4 of sec. 3, was worked from 1883 to 1897 and 118,000 tons of ore was mined. From 1907 to 1915 extensive exploration was carried on over the whole of sec. 3, including 79 diamond-drill holes with a total footage of 26,000 ft. The Chase mine, on the NE.1/4 of the NE.1/4 of sec. 3, was developed from this exploration work, but after about 200,000 tons had been mined the property was abandoned. From 1908 to 1910 exploration was carried on by another company on sec. 4, 47-28, including four drill holes with a total footage of about 5000 ft. Much of the drilling on sec. 3 and of the exploration work on sec. 4 are within the present developed area of the Blueberry mine. A general campaign of diamond-drill exploration was undertaken in 1924, and within a year a considerable amount of ore was developed. The Ford Motor Co. then took an option on the property and carried on check drilling and diamond-drill work until the spring of 1926, when enough ore had been developed to warrant the sinking of a shaft

Jan 1, 1937

By C. A. Pierce

Underground operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Government came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting requirements of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1937

By John J. Croston

The year 1935 witnessed one of the world's oldest industries—gold mining—attain the stature of a billion dollar business. Preliminary estimates indicate that somewhat over 30,000,000 oz. of gold was produced, the largest output ever recorded and exceeding the previous year by more than 11 per cent. Of this huge total the Witwatersrand field produced about 10,800,000 oz., compared with 10,480,000 oz. in 1934. Russia was apparently the stellar performer, and from incomplete data it appears that between five and five and a half million ounces were produced by the Soviets compared with 4,200,000 last year and 2,814,000 in 1933. The United States nosed Canada out of third place with a production of 3,546,000 oz. against 2,916,000 in 1934, while Canada increased her total from 2,965,000 to 3,291,000 oz. Similarly, gains of lesser magnitude were made in Australia, the Gold Coast and other countries. As a result of great activity in developing outlying areas on the Rand, and the great number of new companies building mills in Canada, Australia, the Gold Coast and the United States, the years 1936 and 1937 should see new high records, as these new producers will more than offset any decline in the older properties. The whole world has become "gold conscious" during the past three years. It has been the subject of innumerable articles by economists and others, but, unfortunately, because of their lack of actual mining knowledge, they have treated the production of gold as a static affair, ignoring geological and technical factors. It is hardly necessary to draw attention to the fact that the world's gold-mining industry was slowly but steadily shrinking in importance, owing to the gradual depletion of known deposits that were profitable to work at costs existing prior to 1929. The International Geological Congress at Pretoria and the League of Nations Committee drew attention to the estimates of the mining experts of the various governments predicting a steady falling off in world production. On the Rand there

Jan 1, 1937

By George B. Holderer

The relation between man-hours of labor and production may be correlated for any industry, and already it has been widely used in piecework studies. It is not in general use as yet for recording labor efficiency of an enterprise or an industry. An exception to this is the Cement Institute, which tabulates the man-hours used in each operation and thus gets the total man-hours per barrel of cement. The writer knows of one steel company that keeps a complete record of man-hours for every operation from mining the ore to finishing the product. No doubt many others find the information useful, and such a study could be of value to the mineral industries.

Jan 1, 1937

By Donald E. Cummings

Certain dusts are dangerous when inhaled, but most hazardous of all dusts are quartz or other forms of pure crystalline silica. The inhalation of dusts containing silica in combination with other elements gives rise to changes in the lung which differ from those produced by pure silica. As a generality, silicates are less dangerous than pure crystalline silica and vary greatly among themselves in harmfulness. Repeated analyses have shown that approximately 70 per cent of the total number of particles involved in any dust-producing operation are below 1 to 2 microns in diameter. (A micron is approximately 1/25,000 in.) Similar studies of dusts recovered from silicotic lungs post mortem have demonstrated essentially the same size frequency distribution, except that the upper limit of size retained in the air sacs is approximately 10 microns. Experiments carried on by Gardner and the author have further demonstrated that greater changes were produced by a fixed weight of very fine quartz particles (2 to 3 microns and smaller) than by the same weight of slightly larger particles (8 to 10 microns). Any attempt to control a dust hazard should therefore be directed toward the removal from the working atmosphere of particles less than 10 microns in size, and particularly those below 3 microns. All industrial hygienists agree on this matter, but there remains considerable dispute as to the lower limit of particle size capable of causing injury. It has been generally conceded, however, that particles of harmful dusts smaller than 1/4 to 1/2, micron are not essentially concerned in the development of pulmonary fibrosis. This opinion is partly substantiated by the existence of large numbers of these small particles in practically all atmospheres that are not associated with any known hazard. Such particles are so small that they have very little mass, fail to settle even in quiet air, and probably are not easily retained in the lung. Until further research proves that they are involved in the dangers provoked by the inhalation of certain dusts, engineers will generally agree that it is better to disregard them.

Jan 1, 1937

By V. R. Garfias

Even before the arrival of Cortes in 1519, the history of Mexico was closely linked to that of its mineral production; the mining activities of the Aztecs being thus described by Clavigero, one of the early historians: In the mountains of Anahuac there abound in veins all kinds of metals, and infinite variety of other fossiliferous products. The Aztecs obtained gold from the countries of the Cohuijques, of the Mixtecas, of the Zapotecas and from various other places. They gathered that precious metal usually in gain, from the sands of the rivers, keeping a certain portion for the crown. They obtained silver from the mines of Taxco, of Tzumpango and others; however, this metal was not as esteemed by them as by other neighboring nations. They had two kinds of copper; one hard, which they used instead of iron to make sickles, lancea and all kinds of rural and military instruments and another, soft, with which they made kettles, goblets and other receptacles. This metal abounds mainly in the province of Zacatula and in that of Cohuijques, which at present is in the kingdom of Michoacan. They obtained tin from the mines of Taxco and lead from those of Izmiquilpan, located in the country of the Otomies. From the tin they made money, and the lead, we know they sold in the market places, but we ignore the uses to which they applied it. They also had mines of iron in Tlaxcala, in Taxco and in other places; but they either had not discovered them, or did not know how to make use of the metal they contained. In Chilapa there were mines of mercury, and in other places there were mines of sulphur, alum, vitriol, cinnabar, cohre and of a white earth which they esteemed highly. As regards mercury and vitriol, we do not know of what use they were to them; the other metals they used in paintings and dyes. There were then great abundance of amber and asphalt—bitumen of Judea—on the coast of the seas and many cities of that territory paid tribute of one and the other to the kingdom of Mexico. They mounted the amber in gold, and it was only used as ornament and display by them. With the asphalt they made certain perfumes. The following extracts dealing with pre-Colonial gold are taken from the famous " Cartas de RelaciÓn " to Charles V, in which Cortes described the progress of the Conquest: . . . here there came two chiefs who owned lands in the valley; one four leagues down the valley and the other two leagues up the valley and they gave me some gold necklaces of little value and seven or eight girls. . . . . . . that day I left the City of Churultecal and traveled four leagues to some villages of the City of Cuasucingo where the natives received me very well and gave me women and pieces of gold. . . .

Jan 1, 1937

By Albert H. Fay, William B. Plank

In practically all rock-excavation problem there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation. Scope of Work The section of the roadway involved was about 200 ft. long and on a 6' curve. It was necessary to relocate points on the curve, from which all faults and cleavage planes were located and measured by the use of transit and clinometer. A plan (Fig. 1) showing the blasting tunnel, the roadway, and traces of the faults and cleavage planes on the level of the roadway, was prepared; also 13 cross-sections at varying intervals, showing the original face of the hill and the face after the blast. The original and final profiles of the rock face, taken from the plans of the State engineers, are shown in Figs. 2, 3 and 4.

Jan 1, 1937

By Charles W. Wright

At most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bulldozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners' are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1937

By G. C. Bateman

The Workmen's Compensation Act of Ontario was passed in 1915 and Miners' Phthisis was added to the list of compensable industrial diseases in 1916. Under this provision of the Act only about two cases were compensated per year. In 1924, The Department of Public Health made a survey of miners in the four principal camps—Sudbury, Porcupine, Kirkland Lake and Cobalt—and the survey indicated that an alarming proportion of the men exposed to dust had silicosis in one or other of its several stages. A number of conferences were held between representatives of the Department of Mines, the Department of Public Health, the Compensation Board and the mine operators. The operators were advised that in the earliest stages of silicosis there was no physical disability and if men in that stage were removed from underground there would be little danger of permanent disability. They were further advised that if active steps were taken at once to compensate men that had some real disability and remove from the mines men in the early stages of silicosis, the first cost would be the greatest and thereafter their liability should decrease. As a result of this advice, and having at that time no reason to doubt the findings of the survey, the operators agreed to do all that was asked of them and cooperate with the Government in the steps believed necessary to meet the situation, and to provide compensation for the men affected. Amendments in 1926 Arrangements were made for the necessary amendments to the Mines Act and the Workmen's Compensation Act and these amendments were passed in 1926. The Amendment to the Mines Act provided that all underground employees must be the holders of certificates certifying that they were free from tuberculosis of the respiratory organs and further provided that the certificates must be renewed annually. The Government, however, at that time refused to adopt a form of certificate for applicants certifying as to their physical fitness for underground work. The Amendments to the Compensation Act defined both silicosis and

Jan 1, 1937

By N. O. Johnson

The Hog Mountain mine is a pyritic-gold property in the north central part of Tallapoosa County, Alabama, at an elevation of 800 ft. in the southern Appalachian region. It is 13 miles by a good secondary road from Alexander City, a station on the Central of Georgia Railroad. Since its discovery in 1839, the mine has been worked intermittently. The records of past operations are few and are scattered over a long period of time; however, available information indicates a production of approximately 12,000 oz. of gold prior to the present company's activities, which started in 1933. Additional 7844 oz. has been produced under the direction of the present management. The ore from stopes has averaged 0.200 oz. gold per ton; the ore from development, 0.136 oz. gold per ton. Silver, copper, iron and sulphur are also present but to date are of minor importance. The grade of ore in comparatively narrow veins makes necessary extreme vigilance in the methods of mining. Geology Wall Rock.—Hog Mountain consists of a quartz-diorite intrusion approximately 5000 ft. long by 1200 ft. wide. Its resistance to weathering, as compared to the surrounding schists, has led to the formation of a conspicuous ridge rising 400 ft. above the adjacent country. All the mining operations are confined within the limits of this quartz-diorite formation. Except where there is excessive shearing, either parallel or at flat angles to the quartz veins, all the walls of the stopes within the limits of the veins are strong enough to make timbering unnecessary. Where shearing exists, there may be a sloughing off of the walls, especially in the process of drawing the ore. When this occurs, stulls are placed in the stope, either while the stope is advancing, or while ore is being drawn from a completed stope. In general, very little timber is required. Veins.—The quartz veins have been deposited along fracture planes in the quartz diorite. There are 20 principal veins, all of which are roughly parallel and strike at right angles to the long axis of the formation.

Jan 1, 1937

By Samuel M. Shallcross

The principal function of the Bell limestone mine, of the American Lime & Stone Co., at Bellefonte, Pa., is to supply raw material to the company's modern rotary kiln plant at Bellefonte. Because mining costs are naturally higher than many open quarries with more favorably lying strata, it cannot compete, except to a limited extent, in the markets for road material and fluxing stone. In the broad sense, mining does have an advantage over the average open quarry when the end products are designed for and controlled by process and final inspection for the exacting demands of the industrial and chemical markets. Approximately 80 per cent of the output of the Bell mine is sold in the industrial and chemical markets. And as higher standards are set each year for construction and agricultural work, the remainder of the mine output goes to these two classes. Mining produces more fines than open quarries, and these fines are difficult to market; on the other hand, owing to absence of contaminating clay and impure rock, a greater percentage of the output of a mine is marketable. Because of the great production of fines, rotary kilns for lime burning are necessary when the stone must be mined. In 1921 the American Lime & Stone Co. operated 19 quarries and 72 lime shaft kilns spread over an area of 40 miles between Bellefonte and Altoona, Pa. At that time the lime-production capacity of the 72 kilns amounted to approximately 700 tons per day. After 15 years the company operates three rotary kilns and six shaft kilns, with a combined output of approximately 500 tons of lime per day, concentrated in its single Bellefonte plant (Fig. 1). Its only stone-producing plants are now the limestone mine at Bellefonte and a construction-stone open quarry at Union Furnace, near Tyrone, Pennsylvania. Since the middle of 1922, the management of the American Lime R. Stone Co. has been under the direction and ownership of the Warner Company, of Philadelphia. To the Warner Company's experience, gained through successful operation of lime plants in eastern Pennsylvania for many years, and the successful solution of material-handling problems

Jan 1, 1937

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

By Walter W. Bradley

Mining by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being discharged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,' in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Commission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however, through what is known as the Trinity and Klamath River Fish and Game District. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1937

By John J. Croston

In the closing months of 1936 the copper industry gave every evidence that it was at last on the threshold of an improved era. At the beginning of the year prices stood at 91/4c, which in itself was a great improvement over prices prevailing for the three previous years. Industry generally was showing signs of moving forward in this country, and business was definitely good in certain foreign quarters. The threat of war and preparations for rearmament in Europe and Asia acted as a further stimulus to purchasing. By midsummer the situation had so improved and stocks had been so reduced that the cartel of foreign producers (including American producers with foreign mines) decided to increase the production quota to 75 per cent on Aug. 1. Large-scale buying gave continued strength to the price and by Oct. 1 the quota was increased to 80 per cent, and again on Oct. 15, to 85 per cent. Notwithstanding this the price of copper continued its advance and on Nov. 1, with stocks declining continuously, the cartel increased operations to 95 per cent, then to 105 per cent on Nov. 5. In the meantime the domestic producers, because of the great increase in home consumption, had increased their production by nearly one-half. At the close of the year copper sold at 126 per pound, and since the turn of the present year has reached 17c. This rapid increase has not been wholly justified. Much of the increase was due to the legitimate demands of recovering industry, but rearmament orders plus accumulation of reserve stocks in case of war, purchases in anticipation of labor strikes and purely speculative activities on the London Metal Exchange accounted for the balance. Certainly in view of the state of industry and the general world price level, it appears unnecessarily high. Talk of a copper shortage is sheer nonsense, the recent condition in the market being created by overbuying, leaving but a small volume for speculative supplies. It takes some months for an increase in mine output to reach the market, but production is again overtaking apparent consumption, stocks have begun to increase, and this, together with the reopening of many small

Jan 1, 1937

By Charles A. Kumke

The ('slot" system of mining in use at the Golden Queen mine, Mojave, Calif., does not involve any new mining methods. It is, however, a new combination and adaptation of several stoping systems in common practice. The first plans for stoping operations at the Golden Queen mine called for ordinary shrinkage stopes. The hanging wall of the vein, where exposed, is a very hard felsite with a dip varying from 50° to 70°. The vein itself is quartz, shattered and fractured enough to make it easy to drill and blast to a clean hanging wall. There is no well defined footwall. The footwall limits had to be determined by assays as the metal content faded out into the felsite. Two shrinkage stopes, each approximately 200 ft. long, were laid out and started on the 200-ft. level. One of these stopes, varying in width from 8 to 18 ft., was carried on up to the top limits of the ore, approximately 120 ft., without a break in the operation. The shrinkage system proved entirely satisfactory and low costs resulted from this operation. In the final drawing of this stope, two timbermen followed down on the ore, scaling the hanging wall clean of small fragments and placing an occasional long stull from foot to hanging wall where it was deemed necessary. Few such stulls, however, were required. The hanging wall stood up very well until the stope was entirely emptied of ore. Waste fill was then put into the stope by the glory-hole method, through a waste raise that had previously been run to surface from the middle of the stope. The second shrinkage stope ran into difficulties about 35 ft. above the sill floor. Up to this point the maximum width of the ore had been about 15 ft. The ore suddenly widened into the footwall to a distance of 40 ft. in the north end of the stope. In extending the stoping operations over this, width, it was soon found that the vein material would not arch and support itself. Drilling in this end of the stope was then entirely too hazardous, and all operations were stopped. The ore was drawn through the chutes below as rapidly as possible and as soon as the stope was entirely

Jan 1, 1937

By Theodore Hatch

The pneumatic rock drill operates essentially as a crusher. The rock is shattered into a powder that is removed from the drill hole by the air stream introduced through the hollow drill steel. Particles thus produced vary in size from 1/4 in. or larger down to diameters too small to be revealed by the ordinary microscope. The power consumed by the drill is proportional to the new surface area of the powdered material, therefore the greater the proportion of "dost" produced, the higher the power consumption and the lower the drilling speed. A considerable amount of material ejected from the hole settles on the rock and much of this falls back as the mound builds up to be crushed further before it is removed again. The cushion of dust at the bottom of the hole reduces the effectiveness of the blow of the bit and thus lowers the rate of drilling. The unfavorable working conditions created by the dust also reduce the drilling speed by lowering the efficiency of the operator. Thus, the dust produced by rock drills constitutes a serious drawback to economical performance on all drilling operations. To the economic objections, one must add the more important objection to the health hazard created when the dust contains free silica (quartz). The silicosis problem is a familiar one in many mines, tunnels, and other underground operations as well as in quarries and other types of open rock excavation. Dust is a necessary end product of all pneumatic drilling operations. Its production cannot be eliminated although the proportion of microscopic particles can be reduced by using improved drill steel, proper methods of sharpening, more efficient drills, etc.—improvements that increase the drilling speed largely by increasing the size of the cuttings. The absolute improvement secured in this way is not great, however, and the pneumatic drill must always remain a dust-producing machine. Definite benefits do result, on the other hand, from the use of dust-control equipment that captures the dust as it emerges from the hole and conveys it to a remote point of discharge. Dust production continues, but dust dispersion into the atmosphere is prevented. The dust is removed as rapidly as it is formed, with the following results: (I) The silicosis

Jan 1, 1937