Search Documents

By Reamy Joyce

Conditions in underground mining are so variable that in approaching the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-urrs, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifications. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem. Variable Conditions A study was made recently of the untreated mine ties used by a bituminous coal company in two of its mines, which are about 20 miles apart. The mine ties were secured from the same sources for both mines. A careful check was made over a 10-yr. period on the life of untreated main-haulage ties, and it was found that in the mine where the haulage roads were on intake air the average life was approximately 5 yr., while in the other mine, where the haulage roads were on return air, the average life was 2 yr. A similar variability in untreated timber

Jan 1, 1940

By Reamy Joyce

Conditions in underground mining are so variable that in approaching the problem of the economies effected by the use of pressure-treated mine ties and mine timbers, it is necessary to secure specific data for each mine. Facts must first be dug out to show the service life of untreated timber and the reason for its failure. Generally speaking, decay is the usual cause of failure, but in some mines mechanical destruction is an important factor. Occasionally the two causes combine to produce fail-urrs, and it is difficult to determine positively which factor is responsible. In making comparisons, it is always necessary to start with the cost in place and for this reason there must be accurate information covering the labor cost of installation and the labor cost of renewals. When treated timber is used, it is necessary to know the specifications for the treating process, whether the timber was painted, dipped, treated open tank, or impregnated under pressure according to standard specifications. It is also necessary to know the preservative used and the amount of the preservative that was retained by the timber after treatment. It is also well to know whether the timber was thoroughly air-seasoned before treatment or was green at the time it was treated. The kind of timber available, both untreated and treated, must be known and all of the factors listed above must be taken into consideration in the study of any problem. Variable Conditions A study was made recently of the untreated mine ties used by a bituminous coal company in two of its mines, which are about 20 miles apart. The mine ties were secured from the same sources for both mines. A careful check was made over a 10-yr. period on the life of untreated main-haulage ties, and it was found that in the mine where the haulage roads were on intake air the average life was approximately 5 yr., while in the other mine, where the haulage roads were on return air, the average life was 2 yr. A similar variability in untreated timber

Jan 1, 1940

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable—now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advo- cated. The Institute should take the initiative in stimulating this practice. Introduction Training a student in geology for a career in the mineral industry is still a moot question, one that is likely to be looked at from many different angles, each of which will reflect the background of the individual considering it. From what follows, the training of petroleum geologists is omitted since, although theirs is an equally important phase of economic geology, it is based upon different essentials. The general subject was recently effectively discussed, but from a somewhat different viewpoint, by Professor McKinstry.' The practical problems that confront the young mining geologist are highly varied and in the eyes of his employer apparently almost any demands seem justified. The mining executive wants from the mining geologist results related mainly to overall operations, reports or forecasts that are largely recordable on paper and chiefly in terms of "discovery thinking." The local mining engineer may have many specific questions of his own, chiefly relating to details of geology that apply to mining practice, which he will address to the mining geologist; these usually deal with production quantities; frequently also they necessitate the immediate handling of pressing but apparently minor matters: shall the drill be moved; how soon will we encounter the watercourse which made so much trouble for us above? The client employing a consultant often wants advice or good judg-

Jan 1, 1949

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By Harry H. Power

While the attention of all engineering branches is focused today on changes and improvements in the several curricula, we are concerned here with the many questions arising in industry and college concerning the preparation for the petroleum engineering profession. The succession of problems confronting the petroleum engineer demands a degree of versatility not ordinarily encountered in other professions. As a consequence, the student cannot acquire mastery of all the several engineering branches represented in field practice, and as an alternative, he has learned to appreciate the value of thorough training in the basic or fundamental sciences as a Preliminary foundation for professional work. While our attention is directed primarily to the training of engineers in educational institutions, it is necessary that the ultimate education of the professional engineer be kept in mind. It is apparent that his success as an engineer is limited not only by his educational and job experience, but by his native endowments: mentality, Personality and health. The engineer's lack of job experiences often proves as much a handicap as the lack of adequate college training. If the final product proves to be satisfactory, both industry and technical institutions are to be congratulated. However, if the Product is found wanting, the one most responsible should For the most part, students of engineering colleges have had their interests in applied science awakened at a relatively early age. Manyof them entered college as a convenient means of acquiring a technical education, but undoubtedly would have had better prospects in a shorter program offered by institutions of non-college grade. The activating motive of practical interest is also strong in students suitable for college training, but in many cases an intellectual interest must be awakened in order that it may survive graduation. Numerous engineers believe that this progressive process of selection and determination of career aims is one of the essential services rendered by the engineering colleges. Industrialists, who are more inter. ested in quality than quantity of petroleum engineering graduates, have pointed out the good that should result if more emphasis were given to the work of eliminating the misfits. They also point out the protective measures that have been taken by other professions for the betterment of professional standards. Mention has been ,de of the beneficial results to be obtdned by collective determination of the market for the products of engineering schools, particularly in that the students unsuited to the profession would have an opportunity to prepare themselves for employment more suited to their personalities and other qualifications. In the event that such a system of coordinated personnel direction is developed by the

Jan 1, 1941

By B. W. Gonser, C. M. Heath

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By C. M. Heath, B. W. Gonser

The importance of grain size and its control in wrought brass needs no lengthy discussion, since specifications so often make exact control imperative. Aids to this control are therefore of interest. The effect of a number of different elements on the grain growth of brass under various conditions of annealing has been reported in the technical literature. In particular, a paper by Cook and Miller1 a few years ago, with the discussion that followed, gave valuable information on the effects of iron, phosphorus, manganese, aluminum, aluminum plus nickel, and aluminum plus silicon. Price12 in his discussion of that paper, added a description of some commercial brasses that exhibited a grain-refining effect owing to the presence of 2 per cent A1 and 1 per cent Ni. Gibson and Doss3 have recently given data on the effect of iron on annealing high brass. No comprehensive study, however, has been given to the effect of additions of chromium. It has been the purpose of this investigation to determine the effect of adding various amounts of chromium to a plain cartridge brass, particularly in regard to the effect on grain growth in various annealing treatments after cold-working. Prepakation of Alloys Alloys of high-purity brass of 68.5 Cu, 31.5 Zn composition were made containing from 0 to 0.17 per cent Cr. These were produced in induction furnaces, using unlined graphite crucibles to hold the charge. The melts were cast into rectangular chill molds giving ingots about % by 3 by 10 in. in size.

Jan 1, 1938

By R. V. Vines, E. M. Wise

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

By E. M. Wise, R. V. Vines

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

By Clarence Zener, Howard Clarke, Cyril Stanley Smith

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By Alan U. Seybolt

In examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was suficiently pronounced to warrant some investigation of the annealing characteristics of such compositions. Experimental Procedure The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace! under a charcoal or electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to 1/4-in. thickness, and annealed for 56 hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a 50 per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1942

By Alan U. Seybolt

In examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was suficiently pronounced to warrant some investigation of the annealing characteristics of such compositions. Experimental Procedure The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace! under a charcoal or electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to 1/4-in. thickness, and annealed for 56 hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a 50 per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1942

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940

By Tracy C. Jarrett

The alloying of various elements with gold to produce different colors is an old art, but the effect of each element or combination of elements is not generally known. Investigations have been made in this field by F. E. Carter,' E. M. Wise,2 and L. Sterner-Rainer.3 It is the intent of this paper to present in schematic diagrams the effects of various elements upon the color and the melting point of gold alloys. In this investigation 2-oz. melts made in a high-frequency inductiorl furnace were used for all tests. The melting points were determined by the use of a calibrated chromel-alumel thermocouple sealed in a thin-walled alundum tube. The couple was then submerged in the molten metal and the freezing and melting points were determined by using a Leeds and Northrup potentiometer. By checking several melts using copper, zinc and gold, it was found that the accuracy of determining the melting point was within ± 5" F. To determine the differences in colors and to classify them, a wet tissue paper was placed over the polished samples and examined under a uniform white light. The 2 by 45 by 0.045-in. samples were cut from 50 per cent cold-worked strip. The original ingot was 3 by % by % in. This visual comparison, although not scientifically exact, served as a quite satisfactory means for determining and classifying these differences. The base alloys, or "hardeners," were first made up and analyzed, after which the gold and silver were added. This method of making up the alloys was chosen so that the same base alloy could be used for the gold alloys of different karats. The first series consisted of gold, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the "hardener" and the zinc and nickel replacing copper. The second scries consisted of gold, silver, copper, zinc and nickel, the copper comprising from 85 to 65 per cent of the content of the hardener with the silver, nickel and zinc replacing copper. There was no particular reason for choosing these combinations, except that they gave a color range from red-pink to white.

Jan 1, 1940