Search Documents

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By B. M. Larsen

In endeavoring to put the art of the steelmaker on a more scientific basis, as a means of securing closer control of the product, we must be severely critical of the basis of any theory we use. In particular, we must be careful to distinguish between factors that are primary and those of only secondary impartance. The concentration relations that determine the slag-metal equilibria, which are usually more or less closely attained, are of course of primary significance, but a, dear picture of the whole process requires that the actual rates of the several reactions be taken properly into account. At the high temperature of the steelmaking furnace, all reactions might be thought to be very rapid, but some of them in fact are not; the essential causes of this condition are important to a proper understanding of the process. This paper aims to present, and to justify, the viewpoint that the most significant reaction is the oxidation of carhon in the metal, the progress of which determines the oxygen pressure levels in slag and metal and produces stirring effects, all of which influence the course of the process as a whole. Reaction Rates at Steelmaking Temperatures General experience in reaction rates makes it almost certain that at steelmaking temperatures equilibrium is attained practically instantaneously when the reactants are well distributed in a single liquid phase —that is, in the so-called homogeneous reactions. The actual slowness of some of the reactions in the open-hearth furnace must therefore be attributed to a relatively slow rate of diffusion within the slag or metal phase, which limits the rate at which the reactants can meet each other in the liquid steel or at its surface. That the reactions can be made to go with great rapidity, by proper mixing and stirring of the reacting phases, is indicated by the following illustrations: 1. In the Bessemer process there is intimate contact between air and the whole mass of metal, and the reactions are complete in a few minutes. 2. Perrinl has demonstrated that by pouring liquid steel into slag contained in a deep ladle, and thereby producing almost a slag-metal emulsion, the phosphorus or oxygen content of the steel is adjustcd immediately. 3. Barret, Holbrook and Wood2 observed a quite rapid rate of desulphurization when powdered calcium carbide was stirred vigorously into liquid iron. 4. When a spoonful of liquid steel is poured into a. mold containing aluminum wire, the formation and precipitation of alumina occurs in the fraction of a second required to freeze the surface layer of the tiny ingot. The first three examples all show that any means of increasing the effective surface between slag and metal and promoting intimate mixture of the reacting phases, thereby obviating the limitation imposed by diffusion, will enhance the speed of the steelmaking process.

Jan 1, 1941

By William Carton, Cyril U. Cooledge

BecauSe the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It mas clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stapes below with disastrous results to men and mine. The method of mining developed during the years 1928,1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. Geological Structure The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1940

By Cyril U. Cooledge, William Carton

BecauSe the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It mas clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stapes below with disastrous results to men and mine. The method of mining developed during the years 1928,1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. Geological Structure The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1940

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By Cyril Stanley Smith

For many years sulphur and its congeners selenium and tellurium have been regarded as very harmful elements in copper and copper-rich alloys. Like many similar prejudices, this has been found to be partly wrong. All three of these elements actually have no great effect on the working properties of copper and its alloys, and are desirable additions in that they considerably enhance the machinability of alloys in which they are present. Because of their possible commercial importance, a study of the machinability and other properties of the pure binary alloys was made, as described in this paper, and the effect of selenium on a large number of copper alloys was determined. The current opinion regarding the deleterious effects of elements in this group undoubtedly arose because of occasional failures of tough-pitch copper containing unusually high tellurium, and because of the well-known fact that sulphur causes spewing and unsoundness in tough-pitch copper. Siebe,1 also Deretchey and Margolina,2 studied the effect of sulphur on copper and showed that in the absence of oxygen it was present in the form of copper sulphide, which was less harmful to the properties than an equivalent amount of copper oxide. No data have been published on selenium and tellurium, although the statement is often made, following Eggleston,3 that tellurium makes copper hot-short. Copper specifications call for only traces of these elements. Skowronski and Mosher4 give data on the effect of selenium and tellurium on the conductivity of tough-pitch copper. In private communication Mr. Skowronski says that the samples were hot-forged from small castings and drawn to 0.081 in. diameter, but it should not be inferred from this that these elements are harmless to the working properties of wirebars and commercial shapes. Constitution and Microstructure Constitution.—Sulphur, selenium and tellurium exist in their alloys with copper in the form of copper sulphide, selenide or telluride. These compounds are practically insoluble in the solid state and possess limited

Jan 1, 1938

By Albert J. Phillips

When brasses containing from 61 to 62.5 per cent. copper are very rapidly cooled from temperatures near their melting point to below 0" C., unusual results are obtained. These results are quite unexplainable from a consideration of the old copper-zinc constitutional diagram but they can be satisfactorily explained by means of the diagram revised by Genders and Bailey1 (Fig. 1). Experiments on a 60/40 Brass If an alloy containing 60 per cent. copper is heated to any temperature between approximately 760' C. and its melting point, it will consist entirely of beta. Upon slowly cooling, alpha will start to separate just below 760" C. Since this alpha will contain nearly 65 per cent, copper, the beta will be impoverished by its separation. As the temperature decreases the composition of the separating alpha will approach approximately 61 per cent. and the beta in contact with the alpha will maintain an equilibrium composition approaching 54.5 per cent. copper. If the rate of cooling is extremely slow, especially at the lower temperatures, stable equilibrium will be established by diffusion through the alpha and beta so that eventually 85 per cent. of the alloy will consist of alpha containing 61 per cent. copper, while 15 per cent. will be beta containing 54.5 per cent. copper. With a faster cooling rate diffusion cannot keep apace and the constituents will be cored, the alpha varying from 65 to 61 per cent. copper and the beta from 60 to 54.5 copper. In this case the amount of alpha will be less than 85 per cent. and the beta will be increased correspondingly. The general structure thus obtained is illustrated in Fig. 2. When a more rapid rate of cooling is effected by quenching in water, the alloy is retained largely in the beta form. However, the crystals of beta are usually outlined with dark fringes which at high magnifications are found to be very fine alpha-beta structures almost martensitic in appearance. The separation of this fringe can be greatly suppressed

Jan 1, 1930

By Cyril Stanley Smith

Although alloys of copper and silicon were examined several years ago,' and their excellent mechanical properties were shown, it was not until C. B. Jacobs 2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. Review of Previous WORK on the BinaRy Systems There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described," which indicate that there is a change in solubility with temperature. Copper-silicon System The copper-silicon system has been studied in detail by the author and is described in two papers published in 1928.V he portion of the diagram up to 8 per cent. silicon, as determined by this research, is reproduced in Fig. 1. The author's previous papers include a complete review of the work of other investigators and it is not necessary to deal further with this system here. Copper-manganese System The copper-manganese system has been investigated by several workers, notably Lewis,5 Wologdine,6 Sahmen7 and Schemtschuschny,

Jan 1, 1930

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By H. C. Jennison

Two distinct types of defects occur at times in copper wire as a result of the use of dies of improper design or undesirable wire-drawing practice. The conditions under which these defects may be produced, as well as precautions to be taken in order to prevent them, have been known to The American Brass Co. for many years. The quality of the copper wire bars and rods has too often and unjustly been held responsible for these particular defects and it is to correct any such belief that this paper is presented. An extremely high quality of electrolytic copper has been supplied to the trade by all refineries for the last 20 years at least. The purity of the copper would average well above 99.900 per cent. The casting of the wire bars has been handled in a generally satisfactory manner. The bars have been cast sound, with a flat to slightly crowning set and have been free from sloppy edges, cold sets, etc. In other words, the wire bars have met A. S. T. M. specifications and have been generally satisfactory. For the most part, they have been everything that could be desired from a quality standpoint yet most of the wire mills in this country and in Europe have at times held the quality of the copper responsible for the two types of defects described in this paper. As a matter of fact, these defects are produced entirely in the wire mills. The author has visited many of the large wire mills in the United States and in Europe to investigate these defects. In some cases the trouble has been so serious that the wire mill has ceased operations. At times the wire mills are reluctant to believe that they are responsible for the defective product. The effect of die design, wire-drawing practice, etc., upon the quality of copper wire has received little study on the part of wire mills, particularly those that have commenced operations in the last few years. Two Types of Defects One type of defect is generally known in this country as "check marks;" in Europe it is termed "crowfeet" (Fig. 1). This defect occurs in the surface of the copper wire, in the form of V's, which are always

Jan 1, 1930

By C. T. Eddy, R. W. Drier

The conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in properry. or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest. Effect of Direction of Drawing In 1928 some work was done on hard-drawn copper wires to determine whether wire drawn in a continuous machine (that is, all in one direction) would have a different structure from wire that had a reversal in direction at some stage of the drawing process. The diffraction spectra obtained indicated that as the position of the wire rayed approached the core, a preferential crystal orientation existed, and that the closer to the core the more preferred was the orientation. The data obtained partly corroborated the work done by Schmidt and Wassermanl and by Clark.2 Samples Used in Following Investigation The samples selected for use in both the diffraction work and the resistivity measurements were taken from Nos. 6, 8, 10 and 12 gage

Jan 1, 1930

By Earle E. Schumacher, W. C. Ellis, John F. Eckel

Copper-calcium alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiensl have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1930

By C. H. Mathewson, Kent R. Van Horn

Copper and the copper-base solid solutions readily form twin crystals when plastically deformed at a suitably elevated temperature or annealed after cold deformation. In fact, no feature of the microstructure of these materials is more prominent or characteristic than these straight-sided bands or simple lines of division which sometimes come from groups of thin polysynthetic lamellae, penetrating part way or wholly through the parent grain substance, but often divide the grain into a few or perhaps only two crystallographically related parts. Nearly always the bands as seen in the usual microscopic examination of a specimen come into vivid contrast with the adjacent crystalline material owing to the inherent difference in orientation. Bands which under special conditions of orientation cannot be seen with vertically incident light are often visible under oblique illumination and, when this fails, contrasting effects usually may be obtained by using polarized light. There is no longer any doubt that these synthetic banded structures obtained in the ordinary course of working and annealing are due to twinning of the spinel type which was observed long ago in a number of metals crystallizing in the isometric system.' It has been customary in metallurgical literature to designate these synthetic twins, which grow into prominence during an annealing process, as "annealing twins" without regard to the actual mode of their formation, which is, indeed, obscure and with scant recognition of the fact that prior deformation is essential, no twins having been observed in metal of known unstrained history. This is questionable; especially in view of the fact that in a number of metals and minerals, reorientation into the twin configuration is known to occur as a result of a simple shearing mechanism along the recognized twinning planes and the

Jan 1, 1930

By Daniel R. Hull, H. F. Silliman, Earl W. Palmer

The brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6¾ in. wide by I in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breakdown rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause—however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

By H. F. Silliman, Daniel R. Hull, Earl W. Palmer

The brass-rolling industry has not had a great deal of experience with antimony in its product. There have been some recent excursions with antimony as a corrosion inhibitor in tubes, but in sheet brass it has been regarded with apprehension and generally avoided. This is not to say that contaminations have never occurred, and probably a great many brass mill men have had their own ideas on the effect of such contamination. Our own views were based upon certain experiences some years ago with strip castings that split lengthwise in the early stages of rolling. The nature of this splitting is shown in Fig. I, from a photograph taken in 1922 as a record of 20 bars of 65-35 common brass made with an antimonial brand of copper. These bars were cast 6¾ in. wide by I in. thick by 45 in. long. In the first pass through the rolls, 19 of the 20 split lengthwise throughout their length, while each half curved outward in a wide arc as it emerged from the rolls. In those days, if splitting was not a frequent occurrence, it was not unfamiliar. One can recall periods of short duration when large amounts of common brass would behave in this way. There was nothing imaginary about these spells. The affected metal would split lengthwise in the breakdown rolls, and no maneuvering of mill practice made any difference. The condition would descend like a plague, demoralize the mill for several days, and disappear. It is doubtful if anyone knew the cause—however many explanations may have been current. In 1921 a quantity of split brass was traced to the use of fired small-arms

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943