Search Documents

By H. T. Clark, H. K. Work

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By H. K. Work, H. T. Clark

The instrument for the rapid determination of carbon in steel, described in this paper, was developed originally to facilitate the operation of the pilot-sized open-hearth furnace in the Jones & Laughlin Research and Eevelopment Laboratory. In this small furnace, with its shallow bath, the drop in carbon is accelerated, and a rapid, reliable test for carbon content is indispensable. This problem becomes rather acute when it is desired to finish heats at a carbon content higher than can be estimated with any degree of accuracy by the fracture test. Several independent methods for determining carbon were investigated, therefore, and it was found that a relatively simple magnetic device could be made to give reproducible results. A laboratory instrument was designed and set up for the use of the furnace operators. It was tested exhaustively in the laboratory and was used with considerable success for following the carbon content in the furnace bath. As soon as sufficient data had been compiled to indicate that the instrument might have a wider application, a more rugged model was constructed and placed in the mill to be tested on commercial heats. Finally, about a year ago, instruments were furnished to the plant open-hearth shops, and these have been in use since that time. As a matter of convenience, the instrument has been named the "Carbanalyzer," and will be referred to by this designation in the following pages. $ Eaklier Investigations While by far the greatest number of magnetic investigations in which the carbon content of ferromagnetic materials was considered have had to do with the evaluation of the magnetic properties of steels of known

Jan 1, 1940

By J. M. Gaines, C. H. Herty, M. W. Lightner, H. Freeman

Few subjects have attracted the attention of metallurgists more than oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction; vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;' furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A12O3, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet extraction methods3 give only the more insoluble oxides SiO2 and A12O3, though the iodine method gives MnO to an uncertain degree (information that may be more misleading than no information

Jan 1, 1930

By G. Van Esbroeck, M. Van Weyenbergh

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

By M. Van Weyenbergh, G. Van Esbroeck

The copper mines of the Katanga region in the Belgian Congo lie along the same mineralized belt as those of Northern Rhodesia. There are two distinct types of deposits in that belt, the dolomitic and the quartzitic. In the dolomitic type the metallic minerals are found in a dolomitic limestone country rock. Through oxidation and enrichment, large deposits of high-grade oxidized copper ores were formed, some of which are being worked by the Union Minière du Haut Katanga. Such deposits are all in Katanga. The quartzitic deposits are found in Katanga and Northern Rhodesia. Here the primary mineralization occurred in sandstones and quartzites, in horizons stratigraphically lower than the dolomites. These rocks are not favorable to secondary enrichment and the oxidized zone is poorer than the sulphide zone, which alone contains the ore. There are also in Katanga a few ore-bearing veins. One of them is being worked in the Prince Leopold mine at Kipushi. Prince Leopold Mine The Kipushi ore body fills a fault vein and invades the wall rocks more or less extensively by metasomatic replacement. The vein strikes north-northeast and south-southwest and dips to the west. The variable dip averages 60' to a depth of 300 ft., and more uniformly 80' below 400 ft. In the upper section the average width is 200 ft. and below the width is about 150 ft. The length of the ore body is 2300 feet. The eastern side of the vein—the footwall—is dolomitic and contains irregular masses of ore sometimes extending 100 ft. or more from the main

Jan 1, 1940

By G. R. Fritterer

Investigators in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial temperatures; i. e., 1000 to 1800 C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree. New Thermoelectric Materials A thorough survey of the literature on thermoelectricity revealed that present-day thermocouples could not meet the specifications mentioned above because their thermoelements are metallic. Metals have a marked tendency to deteriorate chemically and their melting points limit their use to low temperatures. Refractory substances, however, are usually resistant to chemical attack and are quite stable at high temperatures. Hence a survey of refractory substances having thermoelectric possibilities was made. One class of thermocouples considered was that in which carbon and a carbide of some metal or nonmetal were the thermoelements. Previous investigators neglected to study this field but certain recommendations were made by them for the use of couples in which carbon served as one element. These proposals are listed in Table 1. The couples suggested are unsatisfactory because of their low thermoelectric powers, the low melting points of their metallic elements, etc. The

Jan 1, 1933

By Robert H. Aborn, J. J. B. Rutherford

It is now well known that troublesome intercrystalline corrosion may occur in austenitic stainless steels following exposure of the metal to a temperature within the range 1000° to 1500° F. (540° to 815° C.). The present paper describes a satisfactory method of estimating the extent of such corrosion, based on the measurement of the electrical resistance of a specimen before and after attack. This new method enabled us to study quantitatively the effect of several factors upon intergranular corrosion in the 18 Cr, 8 Ni type of alloy. The results show that susceptibility to this attack increases with increasing carbon content and grain size and appears to pass through a maximum for certain combinations of temperature of sensitization and period during which the alloy was maintained at that temperature; and are in complete accord with our interpretation of the mechanism of this phenomenon. The method is probably applicable to other metals or alloys subject to intercrystalline attack, such as the aluminum alloys of the duralumin type. The methods hitherto in use for estimating the degree of intergranular attack fall into three types: (1) microscopic examinationll (2) macroscopic examination of fractures, and (3) determination of the time required for complete failure or disintegration.2 None of these lends itself very well to a measurement of the extent of corrosion. The first two are qualitative in nature and the third provides an arbitrary value largely dependent on individual judgment, since failure is a progressive phenomenon and not a sudden event. Our experience is that weight-loss determinations, although valuable in some types of corrosion investigations, bear no simple relation to intercrystalline corrosion in this type of alloy, as is to be expected since the phenomenon probably involves only the thinnest films between adjacent metallic grains. Measurement of electrical resistance has been used recently in the study of some types of corrosion,3 but seems not to have been applied to

Jan 1, 1932

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By R. S. McCaffery, R. G. Stephenson

The statistical analysis of blast-furnace data was undertaken to determine some of the relations which exist between the variables involved in furnace operation, and particularly to show the effect of variation of slag composition on such economically important factors as coke consumption, daily tonnage of pig iron and sulfur elimination. It' was desired to correlate the results obtained in commercial practice with those predicted from a study of the quaternary system lime-alumina-silica-magnesia. This paper presents the results of a preliminary study of blast-furnace daily operating reports, and is intended to indicate the suitability of our method of attack and something of the results that may be expected from an extended statistical examination of such data. It has been shown that blast-furnace slags are not composed of oxides, as reported by chemical analysis, but are actually composed of several compounds, each made up of two or more of the oxides present.' These compounds persist in the liquid state, and the properties of a slag are the properties of a mixture of these compounds, and not of a mixture of the ultimate oxides. The oxides lime, alumina, silica and magnesia make up 94 to 96 per cent. of the usual blast-furnace slag, and assuming that we may neglect the remainder of the components, we may determine the minerals present, and their relative proportions, from a study of the quaternary system involving these four oxides. Operating reports from 15 furnaces were available for this investigation. Complete slag analyses for one slag per day were available, per-mittling the calculation of the mineral composition of the slags used. Basic, malleable and foundry irons, with silicon varying from 0.75 to 4.50 per cent. were included in the reports for this examination.

Jan 1, 1931

By E. A. Anderson, C. W. Siller, Gerald Edmunds

In the pressurc die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger arid a complcte shutdown of the equipment. All of the zinc alloys used for pressure dir-rnsting today contain approximately 4 per cent of aLUminum, which is more than suffieient to make plunger opcration feasible. The clearancc bet,ween the plunger and its bushing is an important matter. As the space bccomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still uscd in some machines. However, the rate at which the plunger c1earance. increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new matcrinls more: capable of retaining the desired clearance during long periods of use. Today marly die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger. operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the pluriger will operatc for a long time, of course.. The authors have developed a laboratory apparat,us in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clearance area.

Jan 1, 1940

By Gerald Edmunds, C. W. Siller, E. A. Anderson

In the pressurc die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger arid a complcte shutdown of the equipment. All of the zinc alloys used for pressure dir-rnsting today contain approximately 4 per cent of aLUminum, which is more than suffieient to make plunger opcration feasible. The clearancc bet,ween the plunger and its bushing is an important matter. As the space bccomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still uscd in some machines. However, the rate at which the plunger c1earance. increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new matcrinls more: capable of retaining the desired clearance during long periods of use. Today marly die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger. operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the pluriger will operatc for a long time, of course.. The authors have developed a laboratory apparat,us in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clearance area.

Jan 1, 1940

By Frank Foote, Eric R. Jette

In a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be considered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe3O4 instead of the original Fe4O4. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously determined fact that the FeO lattice is ionic (i, e., consists of Fe++ and O? ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1. The purpose of the present investigation was to determine the limits of this homogeneity range by means of the X-ray structure analysis. This method has been applied frequently to the study of solid solutions by Westgren and his coworkers as well as by other investigators. The principle is simple: if the change in lattice constant with composition is

Jan 1, 1933

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By John E. Dorn, Oscar E. Harder

The phenomenon of diffusion, according to the most prevalent conceptions at the present time, undoubtedly played an important part in the formation and distribution of metals and minerals in the earth's crust. Apparently there is good evidence that in the geological rate of cooling diffusion caused numerous materials to separate into individual masses or into duplex structures. As is well known, the early steels were made by cementation; that is, by heating wrought ferrous metal in contact with carburizing materials so as to produce a relatively high carbon content on the surface. If the process was continued long enough, the carbon diffused throughout the piece. A more homogeneous product depended upon further heating and forging, so that the carbon diffused to a fairly uniform concentration throughout the metal. In the modern metallurgical industry, diffusion is the basis for many operations; for example, the production of hard surfaces on steels by carburizing, nitriding, cementing with chromium, silicon, boron and beryllium. Castings or ingots as they solidify do not have homogeneous structures, but these structures are made largely homogeneous by suitable process of heat-treating and the resulting diffusion. It is in modern physical metallurgy, however, that we become greatly concerned about the mechanism of the phenomenon of diffusion. The rates of diffusion, effect of temperature and time on diffusion, and the relation of diffusion to the many properties of the parent metal and the diffusing metal have become important; also, we are concerned with the diffusion of a single metal into a complex alloy. For example, what is the mechanism whereby carbon and nitrogen travel into steel? What is the effect of alloying elements in the ferrous material on the rates of diffusions? What is the effect of simultaneous diffusion of carbon and nitrogen? How does chromium, beryllium, boron, or the like, diffuse into the steel, and what are the effects of alloying elements in the steel previous to the cementation process? These inquiries are by no means limited

Jan 1, 1938

By Oscar E. Harder, John E. Dorn

The phenomenon of diffusion, according to the most prevalent conceptions at the present time, undoubtedly played an important part in the formation and distribution of metals and minerals in the earth's crust. Apparently there is good evidence that in the geological rate of cooling diffusion caused numerous materials to separate into individual masses or into duplex structures. As is well known, the early steels were made by cementation; that is, by heating wrought ferrous metal in contact with carburizing materials so as to produce a relatively high carbon content on the surface. If the process was continued long enough, the carbon diffused throughout the piece. A more homogeneous product depended upon further heating and forging, so that the carbon diffused to a fairly uniform concentration throughout the metal. In the modern metallurgical industry, diffusion is the basis for many operations; for example, the production of hard surfaces on steels by carburizing, nitriding, cementing with chromium, silicon, boron and beryllium. Castings or ingots as they solidify do not have homogeneous structures, but these structures are made largely homogeneous by suitable process of heat-treating and the resulting diffusion. It is in modern physical metallurgy, however, that we become greatly concerned about the mechanism of the phenomenon of diffusion. The rates of diffusion, effect of temperature and time on diffusion, and the relation of diffusion to the many properties of the parent metal and the diffusing metal have become important; also, we are concerned with the diffusion of a single metal into a complex alloy. For example, what is the mechanism whereby carbon and nitrogen travel into steel? What is the effect of alloying elements in the ferrous material on the rates of diffusions? What is the effect of simultaneous diffusion of carbon and nitrogen? How does chromium, beryllium, boron, or the like, diffuse into the steel, and what are the effects of alloying elements in the steel previous to the cementation process? These inquiries are by no means limited

Jan 1, 1938

By Chu-Phay Yap

This is the first of a series of theoretical papers on the iron-carbon system. A simple critical analysis of the ordinary constitution diagram of the iron-carbon system yields valuable information regarding the nature of the equilibria in the liquid and solid states. It is shown, for example, that the solute in the melt is Fe3C, but in solid Fe (austenite) the solute is carbon. The thermodynamic laws of the depression in the freezing point of solid solutions have been developed and discussed. Using the usual method of plotting the logarithm value of the concentration of the solvent (in this case, the ratio of concentrations of the solvent in the liquid and solid phases) against 1/T, curves are obtained. A rigorous thermodynamic analysis of these curves has been shown to yield considerable information regarding the internal equilibria of the system, with which the phase rule does not deal altogether. In this way, it is shown again that the solute in the melt is Fe3C, but in the solid rFe the solute is carbon. Various heats of reaction (fusion and transition) and other thermal data have been derived: and discussed with a view to correlating the conflicting experimental data obtained by different investigators of the system.

Jan 1, 1931

On the following pages are abstracts of papers published by the Institute during the year 1931 as Technical Publications, Preprints, and in bound volumes. For abstracts of papers that appear in bound volumes in 1931 but that were published as Technical Publications in 1930, see the Transactions, 1930. Papers that appear in the volume in which this list is printed are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 616. The abstracts are grouped as follows: Page Page Metal Mining....................... 578 ing and Metallography of Non-Milling and Concentration........... 578 ferrous Alloys)................586 IronandSteel...................... 580 Coal Division.. ................ 592 Petroleum and Gas.............. 598 Mctallurgy......................... 585 .............. 613 Institute of Metals Division (Found- Geophysical Prospecting......... 613 Metal Mining Use of Models for the Study of Mining Problems. By Philip B. Bucky. (Tech. Pub. No. 425, 12,000 words.)—This paper describes a research project undertaken to provide a means of studying the behavior of weighty structures such as mines, dams, foundations, etc., with models of the same material in the laboratory. The paper shows that in general it can be done. The underlying theory is explained, the apparatus which was developed and built to do this is described, and the results of laboratory experiments with sandstone mine structures are given. There is discussion of the accuracy of results with the present equipment, the model size necessary, and of the size and type of equipment necessary for the obtaining of results of practical value in the field. Milling and Concentration Ball Mill Studies, I. By A. W. Fahrenwald and Harold E. Lee. (Tech. Pub. No. 375. 25,000 words.)—This paper presents the results of an extensive experimental study of some of the numerous elements entering into ball mill grinding. All apparatus used was equipped with ball bearings. Every experiment was accompanied by a power measurement accurate to 0.005 hp. Quartz was used. Each element studied, such as ball load, was varied systematically. Power curves were obtained for the mill for three general sets of conditions; namely, (1) balls only (2) balls and quartz and (3) balls, quartz and water. For each general condition, power curves were obtained for various mill speeds, ball loads and ball sizes. For conditions 2 and 3, feed sizc and weight and pulp dilution also were studied as variables. The mill output, in grams of finished product per unit of time, was obtained for each test. In a general way, output (mill capacity) paralleled the power data and this attached

Jan 1, 1931

On the Art of Metallography (Howe Memorial Lecture), by F. F. Lucas; Beneficiation of Iron Ore. Abstract of paper by C. E. Williams followed by Round Table Discussion; A Statistical Analysis of Blast-furnace Data, by R. 8. McCaffery and R. G. Stephenson; Air Discharge of Circular Tuyeres, by R. S. McCaffery and D. E. Krause; Open-hearth Steel Process as a Problem in Chemical Kinetics. by E. R. Jette; Carbon-oxygen Equilibrium in Liquid Iron, by H. C. Vacher and E. H. Hamilton; A Thermodynamic Study of the Phasial Equilibria in the Bystem Iron-carbon (Abstract), by Yap, Chu-Phay; Influence of Dissolved Carbide on the Equilibria of the System Iron-carbon (Abstract), by Yap, Chu-Phay; Inclusions and Their Effect on Impact Strength of Steel, I and 11, by A. B. Kinzel and W. Crafts: Method for Electrolytic Extraction of MnO, MnS, FeS and Si02, Inclusions from Plain Carbon Steels, by G. R. Fitterer; Permanent Growth of Gray Cast Iron, by W. E. Remmers; Some Notes on Blue Brittleness, by L. R. van Wert; Austenite-pearlite Transformation and the Transition Constituents, by A. Sauveur; Age-hardening of Austenite, by F. R. Hensel; Transformational Characteristics of Iron-manganese Alloys, by H. Scott; Composition Limits of the Alpha-gamma Loop in the Iron-tungsten System, by W. P. Sykes; Magnetic Properties Versus AUotropic Transformations of Iron Alloys, by T. D. Yensen and N. A. Ziegler; Dilatometric Study of Chrome-nickel-iron Alloys, by V. N. Krivobok and M. Gensamer; Low-carbon Steel, by H. B. Pulsifer; Bright Annealing of Steels in Hydrogen, by F. C. KeUey; Development of Continuous Gas Carburieing, by R. J. Cowan. Transactions, Institute of Metals Division, 1931. 500 pages. Index. Papers and discussions presented before the Division at Chicago, Sept. 22-26, 1930 and New York, Feb. 16-19, 1931. X-ray MetallograpIhy: X-ray Determination of Alloy Equilibrium Diagrams (Annual Lecture), by A. F. Westgren; Suppressed Constitutional Changes in Alloys. by G. Sachs; Texture of Metals after Cold Deformation; by F. Wever. Theoretical Metallurgy: Studies upon the Widmanatitten Structure. I.—Introduction. The Aluminum-eilver System and the Copper-silicon System; by R. F. Mehl and C. S. Barrett; Studies upon the Widmanstatten Structure, 11.—The Beta Copper-einc Alloys and the Beta Copper-alumnum Alloys, by R. F. Mehl and 0. T. Mareke; Application of X-rays in the Manufacture of Telephone Apparatus, by M. Baeyerts; Thermal Conductivity of Copper Alloys. 11.—Copper-tin Alloys; 111.—Copper-phosphorus Alloys, by Cyril Stanley Smith; Thermodynamic Study of the Equilibria of the Systems Antimony-bismuth and Antimony-lead, by Yap, Chu-Phay. Ganeral: Cemented Tungsten Carbide; a Study of the Action of the Cementing Material, by L. L. Wyman and F. C. Kelley; Influence of Casting Practice on Physical Properties of Die Castings, by C. Pack; Fabrication of the Platinum Metals, by C. S. Sivil; Effect of Certain Alloying Elements on Structure and Hardness of Aluminum Bronze, by 9. F. Hermann and F. T. Sisco. The WorkinG oF Metals: Metal Working in Power Presses, by E. V. Crane; Forming Properties of Thin Sheets of Some Nonferrous Metals, by W. A. Straw, M. D. Helfrick and C. R. Fischrupp; Die Pressing of Braas and Copper Alloys, by J. R. Freeman. Jr.; Plasticity of Copper-sina Alloys at Elevated Temperatures. by A. Morris: Directional Properties in Cold-rolled and Annealed Copper, by A. Phillips and E. 9. Bunn; Effect of Combinations of Strain and Heat Treatment on Properties of Some Age-hardening Copper Alloys by W. C. Ellis and E. E. Schumacher; Constituents of Aluminum-iron-silicon Alloys, by W, L. Fink and K. R. Van Horn; Equilibrium Relations in Aluminum-antimony Alloys of High Purity, by E. H. Dix, Jr., F. KeUer and L. A. Willey; Equilibrium Relations in Aluminum-magnesium Silicide Alloys of High Purity, by E. H. Dix. Jr., F. Keller and R. W. Graham; Constitution of High-purity Aluminum-titanium Alloys, by W. L. Fink, K. R. Van Horn and P. M. Budge; Experiments on Retarding the Age-hardening of Duralumin, by E. H. Dix. Jr. and F. KeUer; Aluminum-silicon-magnesium Casting Alloys, by R. S. Archer and L. W. Kempf; Modulurr of Elasticity of Aluminum Alloys, by R. L. Templin and D. A. Paul; Quenching of Alclad Sheet in Oil, by H. C. Knerr.

Jan 1, 1931