Search Documents

By R. Gray

"Experience from Australia has identified what is referred to as non-conventional surface subsidence behaviour. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence”, and far-field horizontal movements – even occurring beyond conventional “angle of draw” limits. This paper discusses such behaviour recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900ft to the north, mining at depths of 330 – 720ft. Investigations (including a subsequent ground movement monitoring program) found a range of evidence in the vicinity suggesting that valley closure and far-field horizontal movements may have occurred resulting from the adjacent mining. The paper discusses the phenomenon of non-conventional subsidence behaviour and the Ryerson State Park case study, including an assessment of mining, geology and subsidence impacts and suggested ground behavioural mechanisms. INTRODUCTION Non-Conventional Subsidence The conventional understanding of coal mine subsidence on which most current subsidence understanding and prediction techniques are based, includes the concept of angle of draw which effectively limits the lateral extent of subsidence effects and impacts. Within this zone – above and marginally beyond the boundary of mining – downward vertical subsidence is the dominant component, together with localised horizontal movements towards the mined region, with related tilts and strains. However, more recent experience from Australia over the last two or three decades has identified what is referred to as non-conventional surface subsidence behaviour. This is found to occur in areas of irregular surface topography or variable terrain, and is characterised by phenomena such as valley closure, valley floor uplift or upsidence, and far-field horizontal movements, all of which can occur beyond the conventional angle of draw limits. NSW Department of Planning (2008) defined the conditions for both conventional and non-conventional subsidence behaviour as follows: “The conventional or general model of surface subsidence, which finds worldwide acceptance, is based on assuming the following site conditions:"

Jan 1, 2015

By P Aguilera, C Guerrero, M Tucker

With the advent of Electronic Detonator Systems in the global mining industry, as well as the development of high precision pyrotechnic delays, the measurement and analysis of delay performance (usually measured in terms of dispersion about a batch mean û precision, and the deviation of that mean from the nominal detonation time û accuracy), has become an important issue. Through the non-conventional use of existing Velocity of Detonation (VoD) measurement technology, it has been shown to be feasible to measure the precision and accuracy of delay detonator series connected in the same manner as a typical open pit bench hook up. This paper describes the work undertaken to compare and contrast performance results obtained using a range of instrumentation including High Speed Video (HSV) filming, digital counter timing using a Hewlett Packard Universal Counter and a digital VoD measurement device. The results obtained demonstrated the practical feasibility of using the latter technology in order to obtain relatively large amounts of data in a time-efficient manner, with a precision of better than 0.5 microseconds, if required. The results also confirmed the close statistical agreement obtained between the three forms of performance measurement, therefore permitting the substitution of the VoD measurement technique for the more capital cost intensive HSV technique and the slow, sample-by-sample HP Universal Counter method. This paper describes the methodology applied and the results obtained.

Jan 1, 2004

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By E. D. Musin, S. S. Gudkov, A. V. Epiforov, S. V. Balikov

The standard technology for processing of gold-bearing sulfide raw material has many problems associated with the use of cyanide as a gold lixiviant. Therefore, many tests to find alternative gold recovery methods are being undertaken. This paper describes some technological solutions, which can become alternatives to cyanide technology in the future. Pressure oxidation (POX) of refractory gold-bearing sulfide concentrates from five different Russian gold deposits were investigated. Concentrate 1 was gold-copper concentrate. Concentrate 2 was gold-pyrite concentrate. Concentrates 3-5 were pyrite-arsenopyrite double refractory concentrates. The POX tests were at temperatures of 110, 200 and 220 °C and oxygen pressures of 1.5, 2.4 and 3.0 MPa were carried out. Gold lixiviants, such as chloride, thiosulfate, sulfite and thiocyanate were tested. The recovery of gold from sulfide gold-bearing concentrates by non-cyanide methods was 97- 99%, and from double refractory concentrates, 86-93%. The tested reagents are less toxic than cyanide, and their use will reduce of the cost of gold production. These methods make it possible to recover gold in acidic media, and eliminate the washing operation and POX slurry neutralisation. In addition, precious metals recovery from POX cakes using lead reduction smelting was investigated. It was shown that the “POX-pyrometallurgical” technology for double refractory concentrates processing could be used with recoveries of gold and silver of 97 and 96%, respectively. Keywords: Recovery of gold, refractory sulfide gold-bearing concentrates, double refractory concentrates, pressure oxidation, non-cyanide lixiviants of gold, chloride autoclave leaching, thiosulfate leaching, thiocyanate leaching, sulfite leaching, reduction smelting, POX-pyrometallurgical technology

Jan 1, 2020

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By A. M. Venter

"SynopsisThe availability of advanced characterization techniques is integral to the development of advanced materials, not only during development phases, but in the manufactured components as well. At Necsa, two modern neutron diffractometers equipped with in-situ sample environments, as well as complementary X-ray diffraction instruments, are now available as User Facilities within the National System of Innovation in support of the South African research and industrial communities. Neutrons and X-rays, owing to their different interaction mechanisms with matter, offer complementary techniques for probing crystalline materials. Both techniques enable nondestructive investigation of phenomena such as chemical phase composition, residual stress, and texture (preferred crystallite orientation). More specifically, the superior penetration capabilities of thermal neutrons into most materials allows for the analysis of bulk or localized depth-resolved properties in a wide variety of materials and components. Materials that can be investigated include metals, alloys, composites, ceramics, and coated systems. In particular, depth-resolved analyses using neutron diffraction complements surface investigations using laboratory X-rays in many scientific and engineering topics. The diffraction techniques can add significant downstream value to the anticipated nuclear industry development activities.IntroductionMaterials characterization is central in understanding the relationship between the structure, properties, and performance in order to engineer materials that fit the performance criteria for specific applications. This is conveniently represented in the form of a tetrahedron, generally known as the material science paradigm (Figure 1).The availability of advanced characterization techniques is integral to the development of advanced metals, not only during development phases, but in the form of manufactured components. At Necsa (South African Nuclear Energy Corporation), modern X-ray and neutron diffraction instruments are now accessible to the South African research and industrial communities. These facilities enable nondestructive investigations of materials and components that could add significant downstream value to the anticipated nuclear industry development activities."

Jan 1, 2015

For the last few years, a new and innovative technique has been successfully used to determine refractory and castable thickness in various metallurgical vessels. The acousto ultrasonic-echo (AU-E) technique uses stress waves to detect metal penetration and delaminations within refractory linings. In addition, it is capable of measuring the thickness of refractory layers and build-up material. The inspection and measurements can be carried out while the furnace is in full operation. The present paper discusses the principles of the AU-E technique, and its advantages and limitations. A number of case studies are presented to demonstrate various capabilities of this new Non-Destructive Testing (NDT) technique.

Jan 1, 2005

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Harold N. Miller

Lost time and services caused by electrical equipment breakdown or cable faults can often be substantially reduced by the use of direct-current high-voltage testing as a maintenance tool. This paper discusses the relative merits of alternating-current versus direct-current testing, pointing out the advantages in size and cost of equipment and more definitive results achieved through the use of D.C. General principles of direct-current high-volt-age testing, types of testing, methods of performing the actual test and interpreting the results are explained. ?The value of insulation resistance measurements and their relationship to high-voltage testing is discussed. Pinpointing the physical location of a cable defect using a fault locator or thumper is described. Reference is made to several organizations that have effected considerable savings with high-voltage test programs. Introduction T HE past decades have seen great advances in the field of electrical power distribution and application. Motor generators, power-operated equipment, cables, etc., have all gone through various stages of improvement both in efficiency and reliability. Un-fortunately, however, power failures and equipment breakdown still occur -frequently with disastrous effects in loss of time,

Jan 1, 1965

By Tom Shumka

INTRODUCTION ?This bull gear inspection technique was developed to provide more accurate data and faster inspection times than current techniques used today. ?Eddy Current Array (ECA) is a non-destructive testing technique that provides the ability to electronically drive multiple eddy current coils, which are placed side by side in the same probe assembly. Each individual eddy current coil in the probe produces a signal relative to the phase and amplitude of the structure below it. ?This data is referenced to an encoded position and time and represented graphically as a C-scan image. Most conventional eddy current flaw detection techniques can be reproduced with ECA inspections; however, the remarkable advantages of ECA technology allow improved inspection capabilities and significant time-savings.

Oct 1, 2010

By Houquan Zhang, Yu Wu, Yanlong Chen, Zhenfu Luo, Aihong Lu

"A non-destructive detection scheme for bolt installation quality was designed by adopting the method of non-destructive detection on bolt installation quality. Based on the field measurements, a random non-destructive detection method for determining the characteristic length including anchoring length, free segment length and initial axial load of bolt was discussed, and the characteristics of increasing bolt axial load in the initial stable stage was obtained. The results show that the bolt axial load and deformation of surrounding rocks correlate each other. Compared with the traditional detection technique for bolt installation quality, the non-destructive detection method has obvious advantages such as random, accuracy, and economic. The method provides a reliable basis for bolt support optimization and stability control of surrounding rocks.INTRODUCTIONBolt support in roadway can make the surrounding rocks and bolt form a structure in the early stage of roadway development through the bolt pre-tension, which can maximize the self-bearing capacity of surrounding rocks. Thus it is a form of active support (Kang, 2007). In order to make the bolt play an active supporting role, it needs to ensure the installation quality of bolting. Thus the bolts can supply a high initial anchoring force and control the deformation of surrounding rocks (Shan, 2009; Wei, 2012). Moreover, bolt supporting is a concealed work. Once installation quality problems appear; it will be difficult for effective detection and screening (Xie, 2008).THE PROBLEMS OF BOLT INSTALLATION QUALITY IN COAL MINE AND ITS DETECTIONThe Problems of the In Situ Bolt InstallationDue to the problems in installation environment, machine, and technique, and workers proficiency (Li, 2003), there are many problems exist in bolt installation. If the borehole depth is too long, the anchoring agent will accumulate at the bottom of the bore, which reduces the anchoring length. Furthermore, if the borehole depth is short due to the poor geological condition, the exposed part of the bolt will be too Jong and the pallet cannot cling to the rock face, which prevent the pre-tension from being applied. The pre-tension is very important for bolt installation. If pre-tension is insufficient the rock bolt cannot control the deformation of surrounding rock efficiently and the bolt anchoring force will decrease considerably. The bolt length is another important parameter for anchoring quality, which will affect the control area of bolt supporting. In addition, the cleanness of drill hole has a great influence on the effective anchorage length of bolt. If the drill hole cleaning is not enough, it will directly affect the anchoring agent and the contact area of surrounding rocks, which will decrease the effective anchorage length and initial anchor-force."

Jan 1, 2016

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By George Piscsalko

"Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.IntroductionDrilled shafts and Augered Cast-in-Place (ACIP) piles have been increasingly used over the past several years due to several reasons including the reduced noise and vibration, speed of installation for ACIP piles, and the large axial and lateral capacities which are attainable for very large drilled shafts. ACIP piles are drilled and cast without any visual inspection. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2017

By George Piscsalko

Quality control of drilled shafts and ACIP piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult to properly inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. In other cases, such as ACIP piles, it is impossible to inspect the shaft in any manner prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity in drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity over 100% of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube typically 12 to 48 hours after concrete placement, or from embedding thermal wires within the shaft prior to concrete placement and monitoring them with unattended data collectors for 12 to 48 hours after concrete placement. This Thermal Integrity Profile method will be described in detail and several case histories will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing, and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

By Edmund J. Cardoza

WELCOME TO THE DEEP FOUNDATIONS INSTITUTE 26TH ANNUAL CONFERENCE AND WELCOME ESPECIALLY TO THIS SEMINAR ON NON-DESTRUCTIVE TESTING OF DRILLED SHAFTS, PRESENTED BY MEMBERS OF THE DFI DRILLED SHAFT COMMITTEE. MY NAME IS ED CARDOZA; I AM A VICE PRESIDENT WITH THE MILLGARD CORPORATION, A DRILLED SHAFT CONSTRUCTOR FOCUSING PRIMARLY IN THE EASTERN HALF OF THE UNITED STATES.

Jan 1, 2001

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014