Search Documents

By Christopher Andreae

Years before iron and steel works were established at Sydney, several thriving although short-lived iron works operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron works. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principal fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel works dominated production for Nova Scotia and the rest of Canada. Two sites achieved prominence in the nineteenthcentury Nova Scotia iron industry: Londonderry and Ferrona (Fig. 1). Londonderry, the larger and longerlasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace. But once the furnace was blown out in 1904, the population gradually drifted away.

Jan 1, 1999

By Christopher Andreae

"Years before the present iron and steel works were established at Sydney, several thriving although short-lived iron work s operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron work s. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principle fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel work s dominated production for Nova Scotia and the rest of Canada.Two sites achieved prominence in the nineteenth-century Nova Scotia iron industry: Londonderry and Ferrona. Londonderry, the larger and longer-lasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2,600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace, but once the furnace was blown out in 1904, the population gradually drifted away.Early HistoryThe history of Nova Scotia's iron industry began in 1604 when Samuel Champlain became the first European to identify iron ore in the future province. Despite this early acknowledgment, iron was not smelted commercially in Nova Scotia for another two hundred years. Although primitive smelters of the period produced more iron than could be used locally, early settlers depended on imports of iron from Britain and the United States."

Jan 1, 1983

By P. J. D. Lloyd

INTRODUCTION The mining of gold commenced on the Witwatersrand in 1884, and reached a mature state by about 1910, when nearly 20 million metric tons were mined. Mining has continued on the central Witwatersrand, the area of the first mining, at a similar rate until recent years. As a result, well over 1 billion tons of gold mining wastes have been dumped along a line over 80 km long, centred on Johannesburg and stretching from Randfontein in the west to Nigel in the east. (see Figure 1). The population of this conurbation, which straddles the line of mining, has grown to about 5 million. In 1922 uranium was first discovered as a constituent of the ore (and thus of the wastes). Investigations in the 1940's revealed that values near Johannesburg were low, but that, at the western and eastern ends of the central Witwatersrand line, and in the new areas centred on the towns of Carletonville, Klerksdorp and Welkom up to 200 km from Johannesburg, values were adequate to permit uranium recovery. Commercial production commenced in 1952, and by 1979 over 100 000 tons of uranium oxide had been produced. There thus arises on the central Witwatersrand nearly 1,3 billion tons of slimes containing an average of about 0,005% uranium and about 1,8% FeS2. The material grading is about 70%-75µm, and the primary mineral is silica (over 85%). The material is contained in dams constructed hydraulically. A typical dam has an area of about 100 hectares and there are over 6000 ha under slimes dams in the area of concern. The treatment of these dams for uranium recovery commenced in 1977. The situation has thus arisen whereby potential uranium ores have unwittingly been dumped in significant quantities within a major metropolis over a period of nearly a century. The purpose of this note is to review the experience arising from the potential hazard over a considerable time.

Jan 1, 1980

By R. C. J. Goode, W. S. Rapson, W. R. Lawrie, L. W. P. Van Der Bosch

W. R. Lawrie (Member): As all the Institute members present are aware, the Ninth Commonwealth Mining and Metallurgical Congress was held in Great Britain from 3rd to 24th May, 1969. The Congress opened in London and the first week was devoted to technical sessions. Several receptions and other forms of entertainment were held in the evenings. The Congress was attended by some 1 200 delegates, many of whom were accompanied by their wives. As can be imagined a large organisation was needed to cater for all the whims of these delegates, to arrange accommodation and to provide transport for the technical trips, for the receptions and for the sight-seeing tours. Papers presented at the technical sessions proved of great interest. It was stimulating to hear of the developments taking place in the various branches of mining and metallurgy. The discussions which developed between men from so many different countries were thought provoking, led to new friendships and most of us made valuable contacts for the future. There were 141 papers presented in the one week. They were given in four separate halls with two, three and sometimes four papers coming up for discussion in each of the three sessions per day in each hall. Among the more interesting subjects were those concerning off-shore drilling and the facilities for production of petroleum and natural gas. Beach mining at Consolidated Diamond Mines drew a large audience. Automation, mechanization and other technical developments were well described and we were brought up to date with modern techniques of mineral prospecting. There was general discussion on the future of the mineral industries together with comments on the consumption and price trends of these metals and minerals. The future of uranium, of vital interest to us in South Africa, came in for much debate. During the first week, besides attending the technical sessions and seeing some of the sights of London, we were royally entertained. There was a banquet, attended by some I 400 people, where we were welcomed by Princess Alexandra, a reception by H.M. Government in the Banqueting House, and we were entertained at the House of Lords on a terrace overlooking the bustling and rather muddy river Thames. Then there was the visit to the Glyndebourne Opera. It is only in London that at 3 o'clock of an afternoon, nearly 1 000 people all togged up in dress suits and long dresses and carrying packets of sandwiches for supper could arrive at a station to catch a train, and not even cause a stir of interest or a raised eyebrow! This is the way we travelled 60 miles to the opera from London. Surely there can be no more picturesque or romantic a setting for an opera than this large 400-year old red brick manor house nestling in the green valleys of the unspoilt Sussex countryside. It was a glorious evening and though we returned somewhat late and tired, not one of us would have missed this experience. After the first week in London there was a choice of tours of one week to London and the Home Counties, Cornwall, a Geological tour to Scotland, South Wales, and North England. These were followed by further one week tours to Yorkshire and Lancashire, Scotland, West Country and Midlands, a Geological tour of Wales, and a Mining and Geological tour to Jurassic Iron Mines. We then returned to London for the final session and closing banquet. Post-congress tours were arranged to Europe and to Ireland. It was a wonderful Congress, a great experience, we made many friends and may there be many more congresses! . L. W. P. van den Bosch (Member): Much has already been said in appreciation of the excellent organisation and arrangements made for the delegates who attended this Congress. This report is confined to a brief discussion of the personal impressions gained from the papers presented and the technical visits attended. The papers covered a wide variety of subjects ranging from highly theoretical observations to practical descriptions of operations. There were three main themes, VIZ: 1. The attention given to research and its forceful application to practical operation. 2. A steady development in mechanization and automation leading to savings in manpower. 3. Improvization, modernization and adaptation of exisitng facilities. Thoughts on these themes can best be illustrated by comments on some of the industries visited. COAL The National Coal Board (N.C.B.) has been most progressive and all of us have heard of the Bevercotes Colliery with its completely automatic mining and coal handling equipment. This was not, unfortunately, on show but there is no doubt that this is one of the greatest advances in coal mining leading towards continuous production. Coal in Britain is fighting for its life against oil, North Sea gas, imported gases and nuclear power. Output is dropping, the less efficient collieries are closing down and efficiencies are steadily rising as the following tabulation indicates: In 1931: 1 million men produced 300 million tons of coal In 1947: 0.7 million men produced 230 million tons of coal In 1968: 0.4 million men produced 160 million tons of coal

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

By William E. Ford, Edward Salisbury Dana

The Niobates (Columbates) and Tantalates are chiefly salts of metaniobic and metatantalic acid, RNb2O6 and RTa2O6; also in part Pyroniobates, R2Nb2O7, etc. Titanium is prominent in a number of the species, which are hence intermediate between the niobates and titanates. Niobium and tanta¬lum also enter into the composition of a few rare silicates, as wöhlerite, låvenite, etc. The following groups may be mentioned: The isometric PYROCHLORE GROUP, including pyrochlore, microlite, etc. The tetragonal FERGUSONITE Group, including fergusonite and sipylite. The orthorhombic COLUMBITE Group, including columbite and tantalite. Also the orthorhombic SAMARSKITE GROUP, including yttrotantalite, samarskite, and ånnerodite. The species belonging in this class are for the most part rare, and are hence but briefly described.

Jan 1, 1922

"In 1989, improved milling and recoveries resulted in a record production of 7 722 200 Ib Nb2P5 at the Niobec Mine. At the beginning of 1990, proven and probable reserves stood at 11 952 000 tons grading 0.65% Nb205. This year, the world steel market has slowed and as a result, niobium consumption is down. Consequently, production at the mine dropped 14% for the second quarter.IntroductionThe Niobec Mine is located approximately nine miles northwest of Chicoutimi, Quebec, (Fig. I). After ten years of production, the Niobec Mine is the only operating niobium mine in North America and the second largest producer of niobium in the world after Brazil.The Niobec Mine is a joint venture held equally by Teck Corporation and Carnbior. Teck Corporation operates the mine while Cambior is responsible for marketing and selling the niobium pentoxide concentrate (Nb2P5).The deposit was discovered in 1964 following an airborne radiometric survey in search of uranium. However, mining of the deposit did not begin until 1976. The initial production capacity of 1500 tons per day was increased several times to the present capacity of 2450 tons . The deposit is considered as an ample source of pyrochlore concentrate for at least 15 years at the present production rate.Niobium, also known as columbium, is a greyish-white metal used primarily as an alloy in various steels and other metals. The use of niobium in alloys heightens tensile strength and improves corrosion resistance while at the same time reducing the weight of the alloy. Niobium is also used in the fabrication of steel for the aerospace, automobile, and oil and gas pipeline industries. Although substitutes for niobium exist, their use often results in diminished performance and net cost increases."

Jan 1, 1990

By Sarah Belair, Gauthier Deblonde, Valerie Weigel, Alexandre Chagnes, Gerard Cote

"Niobium and tantalum are strategic metals for electronic and alloys industries. They are produced by pyrometallurgy and hydrometallurgy but most of the niobium and tantalum production processes are not environmentally friendly. For instance, in the hydrometallurgical route, niobium and tantalum separation can only be achieved by liquid-liquid extraction in the presence of hydrofluoric acid by taking advantage of the difference in niobium(V) and tantalum(V) speciation in fluoride-based media. Therefore, the environmental footprint of hydrometallurgical processes for the production of niobium and tantalum could be clearly lowered by replacing HF or NH4F by greener media such as alkaline solutions in which high solubility of niobium(V) and tantalum(V) can be achieved.The development of such new efficient and environmentally friendly hydrometallurgical processes requires a fine description of the physicochemistry of niobium(V) and tantalum(V) in alkaline solutions. Unfortunately, literature data show a huge discrepancy on niobium(V) and tantalum(V) speciation in such media. This paper gives a brief overview of the niobium(V)-tantalum(V) production processes and paves the way to the development of alternative processes in alkaline media by presenting and discussing recent advances in the physicochemistry of niobium(V) and tantalum(V) in these media.INTRODUCTIONNiobium and tantalum are strategic metals since they are used for the production of alloys and super alloys, capacitors and magnets in strategic industries such as electronic, aeronautics and automobile. The main sources of niobium and tantalum are given in Table 1."

Jan 1, 2016

By Mathias Woydt

The tribological and mechanical properties of binderless and metal-bonded niobium carbides (8 or 12 vol.-% of Cobalt, 12 vol.-% of Fe3Al) are presented. Rotating disks made of niobium carbide bearing hard metals were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0,1 m/s to 12,0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, ?x= 0,2 mm, 2/50/98% rel. humidity, n= 105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 8 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal bonded NbCs exhibited low wear rates under dry sliding associated with high P?V load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples.

Jul 31, 2018

By Beatriz Pereda, Ana Clara Fonseca da Silva, Tiago Seixas Bittencourt

Reinforcing steel bars are usually specified based on mechanical properties with flexibility in chemical composition and processing. Most developments, in these steels, are normally focused on alloy and process design to reach minimum cost and conformity to specification. Processing routes using quenching and self-tempering (QST) and accelerated cooling are the most common. Microalloying with V and Nb have been used in rebar. When acicular constituents must be avoided, a combination of Nb microalloying with judicious control of cooling is one of the preferred options. Niobium can contribute to improvement in tensile properties through austenitic grain size control during hot working, precipitation hardening due to carbonitrides or clusters, and hardenability increase. In the present work the alloy design and development processes of a Nb microalloyed steel for rebars are presented. The designed steel has fulfilled the required specification and is under regular production. Austenitic grain size refining – when comparing with the “basic composition” normally used was observed, even without any change in the thermomechanical processing cycle. There are indications that precipitation hardening may also occur. Results indicate that Nb is a good alternative as a microalloying element in rebars.

Oct 1, 2019

By J. Whyatt

A package of bench design programs is being publicly released by the National Institute for Occupational Safety and Health (NIOSH). These programs are designed to provide a probabilistic estimate of the likelihood that various widths of catch bench will be retained. Program modules address the mechanisms of plane, plane step path, and wedge failure. Results are drawn from statistical and geostatistical descriptions of fracture characteristics and other input parameters, and reported as the statistical chance that a given width of catch bench will survive, that is, that a catch bench will remain wide enough to catch rolling and sliding material and prevent such material from posing hazards to miners operating below. The capabilities and application of this software are demonstrated through a case example. Comparing bench width estimates obtained using geologic data with actual widths is a key step in verifying that a program is appropriate for particular site conditions and that proper statistical descriptions of fracture parameters for that site have been developed. Such verification efforts improve confidence, and hence usefulness, of this method for designing future slope benches. Development and release of these programs appears particularly timely given recent progress in photoanalysis methods, which promise to greatly reduce the cost of collecting fracture data.

Jan 1, 2004

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 established the Office of Mine Safety and Health (OMSH) within NIOSH and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. Subsequently, Congress provided additional funding to NIOSH to initiate and continue the program. OMSHR has fulfilled this Congressional mandate through annual Broad Agency Announcement (BAA) solicitations, directed Requests for Proposals (RFP) and Inter-Agency Agreements (IAA), and has further expanded the program through capacity building BAA contracts with U.S. university mining departments in the areas of mine ventilation and ground control. This paper describes the extramural funding program and broadly examines the results of the 150+ contracts issued to date, grouped into key focus areas. INTRODUCTION The Mine Improvement and New Emergency Response Act (MINER Act) of 20061 established the Office of Mine Safety and Health Research (functioning as the Office of Mine Safety and Health Research or OMSHR) within the National Institute for Occupational Safety and Health (NIOSH), and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued over 150 contracts focused on worker health and safety. Initial funding for this program was provided by Congress through two Emergency Supplemental Appropriations (ESA) and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation; ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website2 and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously.3"

Jan 1, 2018

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By Peter Zhang, Daniel Su, Bo Kim, Berk Tulu

This paper summarizes significant findings from the ongoing NIOSH Gas Well Stability research over the past decade; in particular, the important ground control engineering considerations. Longwall-induced surface and subsurface deformations may induce gas well casing deformations and stresses, depending on a few parameters such as overburden depth, overburden geology, topographic relief, strata dip, gas well setback distance, and a gas well casing cementing alternative. Overburden depth to the mining seam is one of the most influential factors; shallow overburden depth induces large horizontal displacement and resulting casing deformation and stress, while deep overburden depth induces large longwall-induced vertical pressure. Overburden geology is another important factor affecting the longwall- induced casing deformations and stresses; the large contrast of bending stiffness at the soft-to-hard rock interfaces tends to induce large casing deformations and stresses. Large surface topographic relief and the presence of soft-to-hard rock interfaces below the stream valley bottoms may shift longwall-induced subsurface gas well casing deformations closer to the surface, thus having less impact on underground. mining operations. Strata dip magnifies longwall-induced deformations by 20% per degree of strata dip for down dip longwall excavations. The gas well setback distance is also a critical geometric parameter; the effect of longwall-induced deformation decreases exponentially as the setback distance increases. Longwall-induced casing deformation and stress will be mitigated or totally uncoupled for uncemented production casing.

Jun 25, 2024

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By Peter Zhang, Daniel Su, Bo Kim, Zoheir Khademian

Building on the research results and knowledge obtained from the ongoing National Institute for Occupational Safety and Health (NIOSH) Gas Well Stability Research, researchers from the NIOSH provided detailed analyses on potential longwall mining and gas well casing interactions at an unconventional shale gas well pad in a West Virginia longwall mine. Following the recommendations from recent research findings, the 5-1/2-inch production casings in all five wells were left uncemented from 4,200 feet below the surface to the surface. Prior to the first longwall panel excavation, NIOSH researchers conducted sophisticated three-dimensional numerical modeling to predict longwall-induced deformations and gas well casing stresses, which were compared with post-first panel and post-second panel mining 40-arm caliper surveys. The pre-mining predictions and comparisons with post-mining 40-arm caliper surveys were presented to all parties involved, including the coal and gas operators, Mine Safety and Health Administration (MSHA), Pennsylvania Department of Environmental Protection (PADEP), and West Virginia Department of Mines (WVDOM), prior to the re-entry operation on December 13, 2022. To date, the re-entry operation is a resounding success.

Jul 1, 2023

By Robert F. Randolph, Dana C. Reinke, Richard L. Unger

Purpose The NIOSH Hearing Loss Simulator is a software training and communication tool for promoting hearing loss prevention. It allows a user or trainer to demonstrate the effects of noise exposure on hearing without experiencing an actual noise-induced hearing loss. Estimates of the effects of different levels of noise exposure are based on the American National Standard Determination of Occupational Noise Exposure and Estimation of Noise-Induced Hearing Impairment, otherwise known as ANSI S3.44. This standard specifies the predicted hearing loss for noise-exposed populations of individuals based on risk factors that include gender, age, sound levels (in A-weighted decibels or dBA), and years of exposure. Algorithms specified in the standard were derived from empirical studies of populations that had no exposure to loud noise and other populations that had experienced various levels and durations of noise exposure. This manual explains the major objectives that can be addressed with the simulator and training scenarios that can be applied to real-life, real-worker scenarios. The majority of this guide explains the simulator's functions in detail. Simulator users are encouraged to read this manual while learning how to run the software. [ ] Training Objectives The main objective of the Hearing Loss Simulator is to increase motivation for taking effective hearing prevention action by demonstrating simulated noise-induced hearing losses. [The Simulator can also help teach the following facts about hearing loss. Hearing loss is affected by noise levels. Hearing loss worsens as the noise exposure duration increases. Hearing loss can become permanent. Hearing loss makes it harder to hear what others say. Most hearing loss is not caused by age. Speech is made up of both low and high pitch sounds. Hearing loss due to noise makes it harder to hear high pitch sounds. Hearing loss due to noise has less of an effect on hearing low pitch sounds.]

Jan 3, 2008

With a growing concern over mine fires, prevention and suppression are hot topics. NIOSH researchers Michael Trevits, Alex Smith and Edward Thimons discuss their research in the area. The leading causes of US mine fires include flame cutting and, welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions and spontaneous combustion. From 1990 through 2007, there were 1601 reportable fires that occurred in the US mining industry -an average of 89 fires per year. The fact that mine fires are occurring with alarming regularity reinforces the importance of recognizing and eliminating the potential hazards. These statistics also show the need for improved control and suppression technology to ensure worker health and safety if a mine fire does occur.

Jan 1, 2008

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010