Search Documents

By C. M. Means

Considering the hazard involved in mining operations, statistics show that a very small percentage of accidents is chargeable to electricity. These accidents do represent quite a large percentage of those that are preventable and they are the direct result of the introduction, for purely economical reasons, of a dangerous element. The introduction of electricity in mines should decrease the hazard, and in no case should electricity be applied to the mechanical operation of equipment if by so doing the dangers incidental to mining are increased. The greater number of accidents are the result of persons coming in contact with exposed conductors at potentials varying from 258 to 508 volts direct current. The use of alternating current at higher potentials than these is quite common in large mines, but it is very rare that an accident happens from this source. This is explained by the fact that where these high voltages are warranted, proper precautions are taken, and the installations are directed by those who fully appreciate the dangers incidental to the work. Direct current is in much more general use than alternating current because of its adaptability to haulage locomotives and the low cost of installation in small operations. We are, however, coming to a more extended application of alternating current for the operation of mechanical devices used in connection with mining. Our underground direct-current wiring system is an evolution from the surface trolley and feeder systems. This is probably due to the fact that our earlier successful applications were electric locomotives, which required the use of a trolley wire. The trolley current has been almost banished from industrial establishments on the surface because of the hazard involved, yet we use it indiscriminately underground, where the dangers from accidental contact or fire are infinitely greater., This does not mean that the underground trolley systems should be eliminated, but it does imply the proper safeguarding of such equipment as is necessarily a part of the trolley systems. It is a fact that the men now employed in the installation and maintenance of mining equipment may be in many cases incompetent or not thoroughly familiar with the work, but they are the men who must do the work and, in order to do it properly, it is necessary that they be educated

Jan 1, 1915

By Irving H. Wentworth

The little town of San Nicolás, Tamaulipas, Mexico, lies approximately 60 miles east of Linares, situated in the State of Nuevo Leon, and 150 miles SE. of Monterey, as shown in the sketch-map, Fig. 1. The place is reached from Monterey by the Tampico train as far as Linares, a distance of 92 miles, and then by coach the rest of the way. It is situated in a narrow valley between low hills, the houses forming one main street and a plaza. It is peopled by about 500 inhabitants. The climate is temperate, the thermometer ranging from 90" in summer to a few degrees below freezing-point in winter; but this severe weather only lasts a day or two at a time, when the " northers " blow. There are no streams in the vicinity, but water sufficient for the use of the people is obtained from wells. The rainfall is about the same as that in the rest of NE. Mexico. The rainy months are July, August, and September. The rest of the year is practically dry, with an occasional showery day or two during the winter, when a " norther " is blowing. Timber is abundant in many localities. There are two varieties of oak, besides mesquite, ebony, "maguira," "patol," and a number of other kinds of trees indigenous to this region. I. History. On the discovery of the silver-lead bearing veins occurring in this district, the mining-camp of San Nicolás was founded in 1767 by the Spaniards, and numerous mines were opened and worked for a distance of about 3 miles east and 5 miles west of the town. At the western extremity and near the Car-rolefia mine, a small town called San Pedro was huilt. The

Jan 1, 1913

By Edward C. Morse

The metallurgical history of Republic has been completely reviewed in a paper presented at a previous meeting of the Spokane Local Section by Professor Thomson;' therefore, the present paper will be confined to matters directly pertaining to the San Poil mill: When I came to Republic last fall to look over the situation there was a plant in operation successfully treating the tailings from one of the earlier mills in the camp. I refer to the mill of the Rathfon Reduction Co. This mill was operating in accordance with modern cyaniding practice, and I was given to understand that the work was very satisfactory and profitable, else it would not have been continued as long as it was. At that time I obtained much metallurgical information of value from Harry W. Newton, Superintendent of the mill of the North Washington Power & Reduction Co. I took a number of samples from the San Poil mine, with the view of determining if Mr. Newton's experience with the ores from the other mines applied to the San Poil ores. I made a large number of tests under a variety of conditions, and found that it was possible to extract as high as 98 per cent, of the values from San Poil ore by the laboratory-tests when the ore was pulverized to 200-mesh and treated with a solution of a strength of 5 Ib. of KCN to the ton. A fairly strong solution was required because of the proportion of silver in the ore, which makes it, from a metallurgical point of view, practically

Jan 1, 1913

By Joseph W. Richards

This method of briquetting flue-dust, or flue-dust mixed with fine ores, or, in a few exceptional cases, coke-dust, has come into large commercial use in Europe, and a small plant is already in operation in the United States. It promisea to become of such great importance to the iron industry of the United States that the following description will certainly interest the majority of our pig-iron producers. Discovered in 1908, the process Tests upon the observation of Dr. Schumacher that blast-furnace flue-dust, while possessing of itself no binding or cementing properties, acquires strong cementing properties if mixed with a very small amount of certain salt solutions, the amount of which is so small that the resulting cementation appears to be rather by catalytic action of the salts added than by the mass-action of such chemicals. To be more specific, fresh blast-furnace flue-dust mixed with from 5 to 10 per cent. of its weight of magnesium chloride or calcium chloride solution—that is to say, with from 0.25 to 2 per cent. of its weight of magnesium chloride or calcium chloride—acquires the property of setting within a short time, from 15 to 60 min., and forming a hard cemented briquette. Alkaline solutions appear to have no action such as described, and they even interfere, if present, with the action of the magnesium and calcium solutions. When treated in this way the flue-dust briquette sets very hard, apparently from pure excess of cementing- and setting-power. It is, therefore, possible to mix with the flue-dust a considerable proportion of inert ore or like material, which has no setting-power by this process, and thus to make a compound briquette containing large quantities of ore mixed with flue-dust, but in which the flue-dust may be regarded as the cement or binding-material. A particularly strongly cementing flue-

Jan 1, 1913

By Ernest Stütz

The problem of increasing blast-furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenh?ttenleute at D?sseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: " The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and it is not any more a question of what is the cost of briquetting a ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron." Dr. A. Weiskopf, of Hannover, admirably condenses in these words

Jan 1, 1914

By Richard Moldenke

One of the little-known characteristics of cast iron, which nevertheless has an important bearing on results where accuracy in machining is essential, is the ability of this material to ease up internal strains when allowed to remain quiescent for a more or less extended period of time. It seems as if the molecules in such a casting, by virtueof their "mobility," can adjust their relative positions to an extent sufficient to overcome some of the existing stresses. The following instance will perhaps give a fair idea of the condition a casting may be in when just shaken out of the sand. A very large sheave-wheel, after shaking out, was taken outdoors to be cleaned and made ready for turning up. It was leaned against the side of the building, but before much could be done an arm tore apart with a loud report. Investigation showed that the sun had been shining on the upper rim, thus adding a slight strain to those already existing within the arm and thus overbalancing the strength of the metal in tension. Had this sheave been kept under cover for a while, or at least until machined, the strains would have eased off sufficiently to allow the sun to look upon it without disaster. It will not be necessary to multiply examples. Every engineer knows the danger of water-hammer in pipe lines, particularly if the latter are of cast iron. Every mechanic knows, or should know, that it is not good to strike a fitting that is under steam pressure. It will be necessary to say a few words on the "internal strains" in castings—the so-called "casting strains" we hear so much about. We all know that to get a casting reasonably true to the dimensions wanted requires a slightly larger pattern. The usual allowance for gray iron is 1/8 in. to the foot (1 cm. per meter) and 1/4 in. to the foot (2 cm. per meter) for white iron (all dimensions). This reduction in length, breadth and thickness in a casting is erroneously called "shrinkage." It should be called "contraction," as for practical purposes it is simply the difference in dimensions of the casting red-hot and cold. The real "shrinkage" covers an entirely different situation. When a

Jan 1, 1917

By Frederick F. Sharpless

The term "segregation," as here used, means the separation of certain natural resources into groups, consisting of one or more members, with the idea that when thus segregated, each group may be more easily and effectively administrated. We may, for example, consider surface rights as distinct from underground rights, and stop there; or we may go further, and deal separately with timber, water, and agricultural rights, or, going underground, we might deal separately with such groups as precious and base metals, clay, oil, gas, etc. The present paper contemplates only the separation so far as practicable, for administrative purposes, of surface from mineral rights. " Classification," in this paper, has reference to the groups into which the government has divided, is dividing, or will hereafter divide its natural resources; first, into the broad classes of mineral and agricultural lands; and, second, into coal, oil, phosphate, brine lands, etc., the central idea being the separation into natural groups for the purpose of simplifying administration and for the purpose of encouraging maximum development and minimum waste. The two subjects are in some respects quite distinct, but as my argument develops, I think it will be obvious why they are discussed in the same paper. In the pursuit of our professions as mining engineers, geologists, or operators, we are continually confronted by conditions with which our present mining laws or regulations are incompatible. It may be a conflict, hardship or injustice, a piece of favoritism, or of unnecessary red tape; or we may see lack of development in a promising locality, and wonder what is the reason. Often we can see where a modification, slight or radical, in the laws would have obviated the difficulty without doing harm to any of those immediately concerned. Such alterations as individuals could intelligently suggest would be based on a relatively small number of situations occurring in their experiences. The published replies to the queries formulated by the various committees on mining law appear generally to reflect personal experience. Concerning a few points, there is a marked uniforhity of opinion, while on other points opinions

Jan 1, 1915

By B. G. Klugh

In a paper before the Institute at Wilkes-Barre, Pa., June, 1911,' Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author² described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some techuical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taker] from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, slid its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sinterecl is intimately nlixed with

Jan 1, 1913

By William Hutton Blauvelt

The type of gas producer in which the ashes are fluxed and run off as slag was among the very earliest made. Ebelmen built the first one in 1840 at Audincourt, France, only a year after the installation of the first gas producer of which we have record. Charcoal was used as the fuel, with blast-furnace slag and clay as flux. My interest in this type of producer began when as a boy I saw the fluxing producer at Chester, N. J., which was invented by W. J. Taylor, and described by him in 1881.' This producer was invented independently by Mr. Taylor to meet the difficulties he experienced in making producer gas for roasting sulphurous iron ores. It will be of interest to review briefly his description of his producer. It was built like a small blast furnace, having a hearth 24 in. in diameter and 24 in. high. The bosh angle was 25' from the vertical; the diameter at the bosh 4 ft. and at the top 3 ft.; the total height 12 ft. The producer contained one water-cooled tuyere 12 in. above the bottom, with a 1.5-in. nozzle. Depth of the coal above the tuyere, 6 ft. Mr. Taylor mixed the coal with from 30 to 40 per cent. of basic blast-furnace slag to flux the ash. Occasionally some limestone was also used, but never limestone alone, as the use of the furnace cinder gave a larger volume of slag and made it easier to maintain a proper fluidity. The producer was blown with a small Weimer blowing engine, delivering 300 ft. of air per minute, at from 1 to 1.5 lb. pressure. The slag was tapped every 2 hr. and was black and glassy in appearance. Broken or egg size anthracite was used. The fine sizes of anthracite could not be made to work. Mr. Taylor expressed the belief that bituminous coal could be used if not too fine, but no experiments were made with this coal. Runs were made of four weeks' duration, with no stops or changes. Mr. Taylor reported the following advantages: 1. Excellent gas, very uniform in quality. The high fuel bed permitted no air to pass unconsumed, and the gas was almost entirely free from carbonic acid.

Jan 1, 1914

By Edward Keller

In a paper, entitled A Uniform Method for the Assay of 'Copper Material for Gold and Silver,' A. R. Ledoux invited the assayers of this country to contribute to a symposium, in which the results of their assays of given samples of copper-matte and metallic copper would be made comparable. This symposiun 2 appeared about one year thereafter; and through it and its discussion, first became generally known the fact that the gold-yield by the all-fire method of assaying is usually higher than by the so-called combination (wet and dry) method, in which nitric acid is employed as a solvent for the copper. In the publication alluded to, the supposed cause of gold-losses in the latter method was declared to be the solvent action of copper nitrate, or of the reduction-products of the nitric acid, upon the gold. Up to a very recent date, gold has been held to be insoluble in pure nitric acid. (The solvent action of any chlorine present in the nitric acid must here properly be disregarded as belonging in the realm of carelessness.) Among later allusions to this topic, W. R. Van Liew3 ascribes the solution of the gold in the combination-assay entirely to the action of nitrous acid at the high reaction-temperature of copper and nitric acid; F. B. Flinn4 believes the low result in gold to be due exclusively to mechanical losses—finely-divided gold penetrating through the filter-paper—but presents no experimental data confirmative of this belief; and 0. Pufah]5 attributes the solubility of' the gold in some coppers to the presence of selenium—a view which appears to be shared by many as-

Jan 1, 1913

By William R. Rumbold

When I was in South Africa during the latter part of 1904, there were three known tin-fields, which may be called the Cape Town, the Bushveld, and the Swaziland fields. The Cape Town Tin-Field. This district is situated near Kuils river, 20 miles west of Cape Town, and 5 miles from Kuils River station on the Cape Town & Stellenbosch railway. The deposits are in granite, intrusive in the Malmesbury beds, which are supposed to be of Silurian or Cambrian age. The granite, resisting denudation better than the surrounding shales, has formed low-lying hills, the highest of which, the Bottlelary Berg, is 1,510 ft. above sea-level. The rock consists of quartz, orthoclase feldspar, and biotite mica; tourmaline is also present. The feldspar occurs in large crystals. The rock is generally decomposed on the surface, and the decomposition sometimes extends as deep as 100 ft. This formation—granite intrusive in Silurian shales— extends for many miles to the northeast, but so far as I know the Kuils River deposits are the only ones now known to occur in it, though probably further prospecting will reveal other deposits. This particular discovery was accidental; alluvial tin being found in the course of boring for oil. The Kuils River Deposit. This deposit comprises both lode and alluvial tin. The lode strikes N-S., and dips about 30' E. into the hill. It is 5 ft. wide, and composed of dense white quartz, in which pinkish-gray cassiterite is distributed in large crystals. The vein also contains considerable quantities of wolframite. Fig. 1 is a rough plan of the relative positions of the lode and the alluvial deposit, the latter, as shown, following the course of a stream, while the lode crops out on the hillside ,

Jan 1, 1909

By Charles P. Williams

The determinations of the specific gravities of a number of samples of lead produced in Missouri, which form the subject of this note, were undertaken with the view of ascertaining if any approximation to the purity of such leads could be reached in this manner. The results would seem to indicate that, whatever value the method may have in the case of the crude and more impure

By Edwin A. Sperry

In 1892 I tested an ore, which was peculiarly difficult to treat, on several concentrators then in general use, including t,he Frue-vanner, the Luhrig table and the Cornish buddle. Owing to the character of the ore it had to be crushed- to a very fine state of division, and the results obtained were far from satisfactory; a large proportion of the values was lost in the slimes, which indicated the necessity of a very careful sizing before dressing. Even after reworking some of the slime-tailings, the results, in my opinion, were not as good aa those which might be obtained on a table designed more especially for the handling of slime. Although the subject of slime-concentration has occupied the attention of many engineers who have threshed the field quite thoroughly, the results obtained in my work led to a careful

Jan 1, 1904

By R. Dawson Hall

The stresses in the simplest structures are often those we find most difficult to analyze. The most complex condition in mine stresses is found in simple tunnels where the roof, the sides, and the floor are a monolith. The functions of the parts are like the parts themselves not distinct and spccialized, and the problems to be solved are like those in a metal structure with riveted joints or a redundancy of bars. This difficulty explains perhaps why the condition has not been treated. But just because it cannot be discussed in its entirety is no reason why it should be treated as an action of parts with spccialized functions as a roof beam with supports and a foundation. The problern cannot be ignored on the ground that it is not of sufficient importance to warrant careful consideration, because conditions of complete monolithism, of which the tunnel is the type, are found materially unchanged in room-and-pillar and in longwall work. This unity between roof, sides, and floor, which to the coal miner is a difficult conception, really deserves a scientific appellation, and perhaps holoid (from holos, whole, and eidos, form) will serve the purpose as well as any other. In a simple tunnel the roof, the sides, and the floor form integral parts of one and the same structure, and the distortion of one cannot be conceived without a consequent strain in the others. Thus when the roof of the tunnel droops by reason of its weight, the upper parts of the sides are drawn in becausc they are integrally connected with the roof and must approach each other whenever, by the sagging of the roof, the distance between any two points in it is diminished. (See Fig. 1.) Thc sides in their turn operate on the floor of the holoid structure, producing a tensile stress. The writer has always been impressed with the value of soap as a means of illustrating the action of mine stresses. With that idea in mind' a cake of naphtha soap measuring 43/8 by 2¼ by 19i in. was taken and a tunnel was made through it 13/4 in. long, 21/2 in. wide and 1¼ in. high. (See Fig. 2.) A load was then placed at the mid-span of the tunnel. Eventually, the upper bar, or "roof," broke at the

Jan 1, 1916

By E. F. Loiseau

In a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it mas expected that a plan devised by Dr. Charles N. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee's sale, and the oven was modified, according to Dr. Cresson's plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust nixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one half of the lumps produced by the press. The plan mas abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is usually dry pitch, which is prepared by separating from the tar, at a temperature of 572' Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392' Fahrenheit. But with common tar very weak fuels are obtained, which do riot burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By L. C. Graton, Joseph Murdoch

I. Introduction......................... 26 1. The Relations of Scale in Geologic Work........ 26 2. General Characteristics of Copper Sulphide Ores..... 29 3. Scope of Present Study................. 31 11. Description of the Important Minerals............ 36 1. Pyrite....................... 36 2. Pyrrhotite....................... 41 3. Chalcopyrite...................... 41 4. Bornite........................ 40 5. Covellite....................... 50 6. Chalcocite....................... 52 7. Enargite...................... 59 8. Tetrahedrite and Tennantite.............. 61 III. Conclusions.......................... 62 I. Introduction. The Relations of Scale in Geologic Work. Many features of human accomplishment rest upon the possibility of representing natural objects on a scale of different magnitude from the actual one. Most drawings, for example, are of very different scale from that of the object depicted, and indeed are useful mainly 011 this account. More important than the question of mere convenience, however, is that of meeting the physical limitations of vision.' Thus, a mural

Jan 1, 1914

By Dorsey Hager

One of the most interesting fields in North America was discovered, early in 1922, near the towns of Sunburst and Kevin, Toole County, Mont. This field produces oil from the Jurassic beds, which heretofore have been of but little importance as oil producers, and promses to be the

Jan 1, 1923

By Dorsey Hager

One of the most interesting fields in North America was discovered, early in 1922, near the towns of Sunburst and Kevin, Toole County, Mont. This field produces oil from the Jurassic beds, which heretofore have been of but little importance as oil producers, and promses to be the

Jan 1, 1923

By Frank Alfred Fahrenwald

A complete list of the elements as given for 1915 includes 18 that melt above 1,700" C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures*and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,' of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation. , Historical.—The alloys of tungsten and molybdenum have received very little consideration during the past. A review of available literature reveals very little regarding this system, and that which has been recorded seems to be at fault. Mennicke2 writes, "Die bekannteste Verbindung

Jan 1, 1917

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915