Search Documents

By W. E. Ruder

It has been pointed out by Stead1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly' well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Ar2. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703" C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750" C. for 0.5 per cent. Si to 860" for 6 per cent. alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730" and 750:. In the preliminary experiments, some of which have been described in a previous paper, it was found that practically all of these steels, when annealed to 1,200" C. or higher, showed grains of comparatively large size. These grains varied in size, however, from about 4 sq. mm. to 50 sq. cm. (see Figs. 1 and 2) under the same conditions of anneal, and it was for the purpose of determining the cause of this difference in size that the experiments herein described were undertaken. From a preliminary study of the chemical composition of the specimens

Jan 1, 1914

By Zay Jeffries

The object of the present paper is to enlarge somewhat on the general principles advanced in my discussion1 of Mathewson and Phillips' article on The Recrystallization of Cold-Worked Alpha Brass on Anneal-- ing.2 It will also serve as an acknowledgment of Prof. Howe's most important remarks on my contribution. In this paper the writer has adopted Prof. Howe's suggestion to substitute the term "germinative temperature'' for "critical temperature for grain growth." Instead of being an exact or certain temperature it should be considered that the germinative temperature phenomenon exists throughout a small temperature range. v Factors Influencing Fast Growth Phenomena The development of grains of macroscopic size at the germinative temperature should be considered the extreme condition of a general rule. When considered in this light it is not strange that the development of these large grains should be the exception and not the rule. The principal factors influencing the operation of the laws of fast growth temperature are as follows: . 1. Rate of heating. In the original paper,' the germinative temperature was defined as "the minimum temperature at which two adjacent grains can coalesce to form one larger grain, provided that this larger grain will have sufficiently increased its power of attack, to enable it to absorb adjacent grains which cannot coalesce with each other. Time is always to be understood as a factor governing the first stage of grain growth." If the time of heating is short, the germinative temperature is raised. The formation of large grains in metals may occur at relatively high temperatures when the rate of heating is rapid. It is to be understood that in such cases, grain growth

Jan 1, 1917

By R. S. Archer

The proper representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem, the complete solution of which will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the Al point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A1 point is an open question, but that complete graphitization (to less than 0.10 per cent, combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440" F. It is the

Jan 1, 1922

By R. S. Archer

The proper representation of equilibria involving graphitic carbon in the constitutional diagram of the iron-carbon system is admittedly an unsolved problem, the complete solution of which will probably require the establishment of more experimental evidence than is at this time available. The object of this paper is to present the author's observations on some of the phenomena in question and his interpretation of this and other recorded evidence. The chief of the recently disputed questions upon which the author has experimental evidence concerns the occurrence of graphitization at temperatures below the Al point. In a paper1 presented at the September, 1919, meeting of this Institute, the following is found: "the results given would seem to indicate that the graphite eutectoid lies at a smaller value of carbon content than has been previously supposed. At least this is true unless there is either a marked formation of graphite eutectoid at these rates of cooling, or a decomposition of pearlite into graphite, both rather unlikely suppositions, but not impossible ones." In a discussion of this paper, H. A. Schwartz2 takes the position that the possibility of graphitization occurring below the A1 point is an open question, but that complete graphitization (to less than 0.10 per cent, combined carbon) commonly occurs above this temperature. Another opinion from the malleable castings industry is found in a recent paper3 by Touceda: "Also the carbide of iron can be broken up into its two soft constituents at the temperature referred to. This temperature is called the critical temperature, or critical range, and for air-furnace hard-iron castings it is in the vicinity of 1440" F. It is the

Jan 1, 1922

By William E. Greenawalt

Ever since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydroelectric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods. Electrolytic methods are ideally adapted to hydroelectric development, for the load is constant throughout the full twenty-four hours, and the cost of both installation and operation of hydroelectric plants is not appreciably greater when operating for twenty-four hours than when operating for eight or ten hours; whereas, in fuel-power generation, as also in smelting, the cost is more or less in proportion to the fuel and power used. Nevertheless, fuel-power generation presents advantages in electrolytic methods, as the power plant may be located in a favorable place while the leaching and electrolytic plants may be located at the mine. The ultimate possibilities of the wet methods have yet to be determined. The possibilities of smelting have been thoroughly worked out; there is no unsolved major problem in copper smelting, and it has practically reached the limit of its possibilities. It seems hardly probable that any future improvement, either of method or apparatus, will greatly

Jan 1, 1924

By R. W. Young, Arthur F. Taggart

The tests herein described are part of an extended series of expel<ments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. Introduction In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of. copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper,. zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot. Floor sweepings occur in all shapes: spirals, thin shavings, pins and pin-like pieces, wire, rods, and buffing-wheel dust are the commonest.

Jan 1, 1916

By E. G. Banks

This paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine—more especially that produced in the upper levels—contains a large proportion of hard, chalce-donic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to obtain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded : Per Cent. Per Cent. On 50-mes11, .- 0.1 On l20-mesh ..8.77 On 60-mesh, . 8-74 On 150-mesh,.... 7.48 On 80-mesh,... 16.06 Passed 150-mesh,... 55.19 On 100-mesh,.... 3.66 The stamp-dnty was 2.89 short tons per stamp per day, or a total of 260 tons daily. Although the extraction on this pulp was: gold, from 88 to 90 per cent., and silver, from 74 to 78 per cent., it was recognized that finer grinding of the sands would prove beneficial, provided a machine could be found to do this work economically. Various grinding-mills and pans were tried, but without satisfactory results, the particles of sand being so hard that the capacity of any of the machines was too small to be economical. The results of grinding in tube-mills in other countries were so satisfactory that three tube-mills mere erected at the Waihi

Jan 1, 1908

By H. R. Tunnell

Every one connected with a mine knows that it is hard to keep down the costs of moving ore from the place where it is broken to the shaft or portal. Considered broadly, the subject of handling would cover all work done in a mine, but here it has been limited to handling ore in stopes and drifts, through chutes, and on levels. Good ventilation and a strict enforcement of rules for the prevention of dust safeguard the health of the men and lower transportation costs. Handling ORe in Stopes and Drifts The object of all stoping is to mine ore of good grade at low cost. In Butte, most of the ore is mined, from veins dipping from 60° to the horizontal to those which are vertical, by means of square-set, rill, timbered-rill, and back-filling stopes. When blasted, a part of the rock is carried by gravity to the grizzlies over the chutes, the rest is shoveled. Rock, when broken in a stope, may be deflected by inclined floors or slides toward the top of a chute leading to the level below. Ore broken clean enough to ship should be carried, by the force of its fall, into a chute or.as nearly into that chute as the safety of the stope and the men permits. Ore that requires sorting, about 80 per cent. of all ore mined, is caught on a grizzly and the waste picked out. Waste rock broken in a stope is used to fill that stope and should be blasted into the gob with as little handling as possible. About two-thirds of all the ore mined in Butte comes from square-set stopes; this method was used in nearly all cases until 1912, when the rill method of stoping was introduced in the Tramway mine, of the Anaconda Copper Mining Co. The shoveling and timbering costs in square-set stopes are high when compared with the costs in the rill stopes. All the ore cannot be carried to the chute, in falling from place, unless the chutes are very close together or the distance from the back of the stope to the top of the chute is sufficient to slide all the ore broken. The number of chutes is limited by the tendency of the ground to cave; if carried too close together the stope is weakened. Small stopes, or blocks,

Jan 1, 1923

By H. R. Tunnell

Every one connected with a mine knows that it is hard to keep down the costs of moving ore from the place where it is broken to the shaft or portal. Considered broadly, the subject of handling would cover all work done in a mine, but here it has been limited to handling ore in stopes and drifts, through chutes, and on levels. Good ventilation and a strict enforcement of rules for the prevention of dust safeguard the health of the men and lower transportation costs. Handling ORe in Stopes and Drifts The object of all stoping is to mine ore of good grade at low cost. In Butte, most of the ore is mined, from veins dipping from 60° to the horizontal to those which are vertical, by means of square-set, rill, timbered-rill, and back-filling stopes. When blasted, a part of the rock is carried by gravity to the grizzlies over the chutes, the rest is shoveled. Rock, when broken in a stope, may be deflected by inclined floors or slides toward the top of a chute leading to the level below. Ore broken clean enough to ship should be carried, by the force of its fall, into a chute or.as nearly into that chute as the safety of the stope and the men permits. Ore that requires sorting, about 80 per cent. of all ore mined, is caught on a grizzly and the waste picked out. Waste rock broken in a stope is used to fill that stope and should be blasted into the gob with as little handling as possible. About two-thirds of all the ore mined in Butte comes from square-set stopes; this method was used in nearly all cases until 1912, when the rill method of stoping was introduced in the Tramway mine, of the Anaconda Copper Mining Co. The shoveling and timbering costs in square-set stopes are high when compared with the costs in the rill stopes. All the ore cannot be carried to the chute, in falling from place, unless the chutes are very close together or the distance from the back of the stope to the top of the chute is sufficient to slide all the ore broken. The number of chutes is limited by the tendency of the ground to cave; if carried too close together the stope is weakened. Small stopes, or blocks,

Jan 1, 1923

By G. D. Van Ardsdale, A. W. Hudson

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,&apos; a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By A. W. Hudson, G. D. Van Ardsdale

Heap leaching, as practiced at Rio Tinto, Spain, while one of the oldest, and probably one of the cheapest, methods of extracting copper from its ores, has not had, until recently, other than experimental application in this country. This has been due partly to a mistaken idea that the Rio Tinto ores possess some obscure and mysterious quality that renders them alone suitable to the process, partly to the fact that tests properly made meant the expenditure of large sums of money and several years time, and partly to the fact that favorable commercial and other conditions are not often found. This paper gives some views on the chemistry and mechanism of the method, an account of the preliminary experiments, and the final plans adopted for a large-scale installation of the method by the Phelps Dodge Corpn. for treating low-grade ore from Sacramento Hill, Bisbee. If results comparable with those obtained from the test heap are to be had from the large plant, this plant will operate on the lowest-grade sulfide ore now being treated commercially in the country. The method has several advantages: The installation cost is low. Interest charges must, of course, be made both on the cost of the ore delivered to the plant and for the plant itself, but as these are low, there is considerable advantage in the ability to regulate output by more or less complete shutdowns in accordance with market and other conditions. The amount of labor needed is small, and the cement copper produced may be considered nearer a finished product than the sulfide concentrates from a mill, and certainly means less installation cost per ton to put into final form by present methods. At Bisbee, conditions were favorable for a trial of the method for, in the preparation of the Sacramento Hill orebody for steam shoveling,&apos; a large amount of material below concentrating grade had to be moved to

Jan 1, 1923

By F. Louis Grammer

The rapid advances on the mechanical side of blast-furnace practice have not always been accompanied by a proper appreciation of the metallurgical requirements. This is illustrated occasionally by the improper use of automatic barrow chargingdevices and bins (introduced at the expense of accuracy in weight), with ores of irregular composition or ores that have been poorly graded. The 100-ft. blast-furnace has not always been advantageous, and in many instances the increase in the number of tuyeres, from 8 or 12 to 20, has resulted in decreased output. The data pertaining to this division of blast-furnace practice are now sufficiently complete to allow inferences to be made. The use of fine ores has indicated the manner in which large outputs could be obtained, as it has emphasized the fact that intimacy of contact. between gases and ore, and coke and air, were more important than the time of exposnre. It was reasonable to suppose that if more points of contact were made between the air and the coke, their union would occur in a shorter period of time, and the coke would be burned more rapidly in the same-sized hearth, and an increased output thereby obtained. In consequence of this theory, many furnace men upon relining a furnace increased the number of tuyeres from 8 or 12 to 20, or even more, frequently with unfortunate results. If the number of tuyeres in an old furnace is

Jan 1, 1904

By Jos. Van Ackeren

Although the Siemens regenerator principle was introduced into byproduct coke-oven design about 40 years ago, many problems of construction, and particularly of heat distribution and pressure conditions, have not been fully solved. Heat should be applied to the walls of a coke oven in such a way that the coking of the charge of coal will be completed everywhere at the same time, and at approximately the same temperature. This means that the application of heat should be uniform from the top to the bottom of the coal mass (except for the thin layer at the top that is purposely kept at a somewhat lower temperature to reduce cracking of the byproducts); also that a little more heat must be applied to the coke end than to the pusher end, because the coal mass is a little thicker at that end. As a modern coke oven is about 40 ft. long and 12 ft. high, a real problem is involved in the proper application of heat to the oven walls so as to secure quick coking time (without endangering the walls through local overheating) and produce coke made at a uniform temperature. Design of Ovens In all regenerative ovens, the points of combustion are arranged in duplicate sets, one set operating in one-half the area of the heating wall and the other set alternately operating in the other half. Because of the reversal of the flow of gases, the points of maximum and minimum temperatures are alternately located at the same places, thus preventing dangerous local overheating. The practicability of the principle of reversal of flow seems to have been recognized at an early date, and has been applied with every conceivable flue arrangement, combustion chamber, and means of air and gas supply. To summarize the various principles that have proved useful for the control of oven-wall temperature, the best practice seems to have resulted from the acceptance of the use of vertical flues; the separate supply of air and gas to the base of these flues, with the resulting flame

Jan 1, 1923

By Jos. Van Ackeren

Although the Siemens regenerator principle was introduced into byproduct coke-oven design about 40 years ago, many problems of construction, and particularly of heat distribution and pressure conditions, have not been fully solved. Heat should be applied to the walls of a coke oven in such a way that the coking of the charge of coal will be completed everywhere at the same time, and at approximately the same temperature. This means that the application of heat should be uniform from the top to the bottom of the coal mass (except for the thin layer at the top that is purposely kept at a somewhat lower temperature to reduce cracking of the byproducts); also that a little more heat must be applied to the coke end than to the pusher end, because the coal mass is a little thicker at that end. As a modern coke oven is about 40 ft. long and 12 ft. high, a real problem is involved in the proper application of heat to the oven walls so as to secure quick coking time (without endangering the walls through local overheating) and produce coke made at a uniform temperature. Design of Ovens In all regenerative ovens, the points of combustion are arranged in duplicate sets, one set operating in one-half the area of the heating wall and the other set alternately operating in the other half. Because of the reversal of the flow of gases, the points of maximum and minimum temperatures are alternately located at the same places, thus preventing dangerous local overheating. The practicability of the principle of reversal of flow seems to have been recognized at an early date, and has been applied with every conceivable flue arrangement, combustion chamber, and means of air and gas supply. To summarize the various principles that have proved useful for the control of oven-wall temperature, the best practice seems to have resulted from the acceptance of the use of vertical flues; the separate supply of air and gas to the base of these flues, with the resulting flame

Jan 1, 1923

By T. F. Witherbee

The following calculation of heat requirement covers the working of the furnace from January 25th to February 14th, inclusive. A short time previous to the first date the furnace had been working rather badly, so that 300 lbs. of ore and 500 lbs. of limestone were taken off. Within the time mentioned the quality of the iron passed

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300&apos; F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300&apos; F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By C. R. Wohrman

A melt of pure electrolytic iron with about 0.4 per cent. sulfur and 7 per cent. manganese was prepared in connection with a study of inclusions in iron. The alloy darkened rapidly when etched with a 10 per cent, alcoholic solution of nitric acid, and microscopic examination revealed the presence of a semimartensitic, semi-Widmanstättian structure (Figs. 1 and 2) closely resembling the structures found by Benedicks in his artificially prepared "meteoric iron."&apos; The structures found by Benedicks were readily explained by the presence in his alloy of the two well-known iron-nickel solid solutions, taenite and kamacite, and of their eutectoid (?) aggregate, plessite. By analogy, one would infer the existence of similar phases in the iron-manganese alloy just described, such an inference being strengthened by the similarity displayed in many ways by nickel and manganese in their effects on iron. Iron-manganese Alloys are Regarded as Homogeneous Heterogeneity of iron-manganese alloys has not been recognized heretofore, judging from the data of standard metallographic books and those of original papers. In fact, iron and manganese are quite generally regarded as completely miscible in the solid state. Dr. Rosenhain,2 for example, writes: Alloys of group (a), of which those of gold-silver, iron-manganese, and copper-nickel are examples, when allowed to crystallize sufficiently slowly to attain their condition of final equilibrium, present a microstructure exactly similar to that of a pure metal—the homogeneous character of the molten solution is in that case so completely maintained that the microscope cannot detect the presence of any second constituent. Guillet and Portevin3 refer to the iron-manganese system as an example of the "case of metals completely miscible in the solid state."

By Walter Mathesius

The use of high blast heats on furnaces melting Mesaba ores is still the exception, the average blast temperatures carried on Mesaba stacks seldom reaching 1,100" F. Some 15 years ago, when the use of fine Mesaba ores in larger proportions to the total burden first came into practice, it was found difficult to employ even those blast heats which it had been possible &apos; to carry with the Old Range ores. The furnaces refused to "take" high heats, and would persistently labor with irregular stock movement, which impaired the practice and increased the coke consumption. By lowering the blast temperature, the working of the furnace became smoother, and experience taught that with the softer and more easily reduced Mesaba ores, satisfactory practice could be obtained with comparatively low blast heats. Therefore a large number of Mesaba furnaces have ever since been operated on very low blast temperatures, ranging between 800" and 1,000" F. In the face of these difficulties, furnace men were slow to recognize that furnaces could be so designed as to permit a free movement of the charges in combination with the use of higher heats. Since higher blast temperatures did not seem to offer great advantages in the smelting of Mesaba ores, investments in hot-blast stoves were not as attractive to the furnace man as labor-saving devices and means of obtaining greater tonnages. The effect of this preference is keenly felt at the present time. It has brought about the peculiar situation, that the majority of our furnace plants (among them some of the most progressive) lack modern and efficient stove equipment. The result is that, even where the proper furnace lines have been adopted and conditions are now favorable to the successful employment of higher blast temperatures, the heats required for the greatest fuel economy are not available. In an endeavor to obtain results, even with inadequate equipment, we find that, at many plants, the stoves are worked far beyond their capacity. This leads, in many instances, to a situation in which the coke saving in the

Jan 1, 1915