Search Documents

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

By Steve Collinsworth, Nils Heinke

In 1989, I realized the definite need for change in the Blast Hole Drilling Industry. With over 25 years of experience in dealing with the industry, I am well inGormed and educated concerning the problems that occur in Blast Hole Drilling. After continues interaction with the Drill & Blast Superintendents, Drillers, Purchasing Agents, Mechanics, and others in the field, a basic understanding was developed as to the origins of the main problems that the industry f&s with their drillings programs.

Jan 1, 1997

By S Bailey

In-field sampling programs generally take time, equating to money, and unless you have an onsite laboratory, you have the issue of having to wait long periods for your data. Until recently, field portable X-ray fl uorescence (FPXRF) analysers, which can help provide instant indicative results, were not able to detect penalty elements, such as Al and Si, or do so reliably enough to act upon.The purpose then of this field test then was to show that the latest FPXRF devices are capable of producing reliable readings on field samples of variable grain size, in particular for Al and Si, such that the readings still correlate well with the assay for those samples and thus be reliable for an iron ore grade control application.We tested RC chip samples on-site in the Pilbara, Western Australia, with the Niton, analysing for a range of elements including Fe, Mn, Al and Si and then compared the results for those elements against assay data for the same. A strong correlation would tell us that the FPXRF results were reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for the all of the four elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 0.998).The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF.The data showed allowed for two conclusions:1. the FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with assay, is reliable for a fi eld application in drilling and grade control; and2. the greatest limitation to data quality is sample preparation.

Jul 11, 2011

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By Fatemeh Saeidi, Malcolm S. Powell, Mohsen Yahyaei

In order to deal with the problems of existing comminution models a new approach towards the development of mechanistic models has been made so as to better understand the physics of milling processes and environments. Despite enormous improvement in this field a comprehensive study of rock breakage characterisation, appropriate for use in these types of models, is still scarce. This paper reviews the existing models of comminution according to ore characterisation techniques and parameters. The authors have looked into the existing testing methods and their applied mechanisms of breakage, using standard test results available at the JKMRC. The study includes classifying testing devices such as the drop weight tester, rotary breakage tester, slow compression, and piston and die based on the few major fundamental mechanisms of breakage that are experienced by rocks in the breakage process. The paper compares the range of particle size and energy utilisation, applied strain rates and loading mechanisms for the equipment. The product size distributions from the various equipment is compared for equivalent input energies, various loading rates but the same level of energy intensity, a broad range of energy including low energy utilisation and fines generation rate for equivalent specific energy input. The results clearly show that the outcomes and conclusions on competence and energy for breakage are a function of the test method that is applied. In ongoing work, it is proposed to investigate common tests that can be applied to characterising ores in a manner suited to modelling a range of comminution devices.

Jan 1, 2014

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By P. M. Solozhenkin, O. I. Solozhenkin

Currently lead nitrate is used as the recommended activator in Au-Sb flotation. However, due to high levels of hazard, the application of lead nitrate constitutes a potential risk for human health and ecosystems. To mitigate the harmful impact of activators on the environment, further research on activation by alternative reagents has been launched to promote the efficiency of antimony ores. In the present study, adsorption of lead, copper and zinc cations has been investigated by nuclear quadrupole resonance (NQR), which has revealed copper and zinc cations penetration into the mineral lattice, although lead cations remain adsorbed on the mineral surface. However, the combination of zinc and copper cations leads to preferential volumetric adsorption of zinc in the mineral lattice and further surface adsorption of copper which positively affects the activation process. It has been established that activation of stibnite can be achieved effectively with the mixture of Cu2+:Zn2+=1:1 as much as with lead cations in antimony ore flotation. As a part of this work, the computational modelling has been used in prognosis of reagent activity evaluation (PRAE) for stibnite and aurostibite flotation by sulfhydryl collectors. The lower PRAE value the stronger the ability of a collector to form a stable complex with a mineral. PRAE has shown a strong negative trend to complex formation on the mineral surface of aurostibite and stibnite. Based on these studies, several collectors have been proposed for effective flotation. To verify the feasibility of proposed collectors tetramethyl (ethyl) thiuram disulfides (TMTD and TETD) have been used for flotation of stibnite, sphalerite, pyrite and arsenopyrite. Flotation performance has been improved significantly with TMTD that allows the avoidance of lead nitrate application and increases the recovery of antimony by 8,16%. Keywords: Stibnite, aurostibite, activation, lead, copper, flotation reagents

Jan 1, 2020

By T. Yue, Z. Gao, X. Tong, R. Liu

"Lead ions (lead nitrate) were introduced to modify the surface properties of scheelite, effectively and selectively improving the flotability of scheelite, with benzohydroxamic acid (BHA) serving as the collector. A series of experiments about the mode of addition and the ratio of lead ion to BHA were conducted and indicated Pb-BHA complexes were the active species responsible for the flotation. And two adsorption models of BHA on the surface of scheelite were established. For both the two adding methods, some kind of complexes formed by lead ions and BHA played a key role in the flotation process. Zeta potential, FTIR, and XPS studies indicated that the adsorption amount and intensity of BHA on the surface of scheetlie were larger by adding the reagents as a mixture. The mixed addition is conducive to form Pb-BHA complexes and improve the adsorption efficiency of BHA on the surface of scheelite, as well as the recovery of scheelite. INTRODUCTION Scheelite, as an important tungsten-bearing mineral, is nowadays utilized mainly by flotation (YIN and WANG, 2014; Sun et al., 2011; Gao et al., 2015; Gao et al., 2015). Flotation separation of scheelite from calcium minerals creates difficulties because of the existence of the same cation in the minerals and similar physico-chemical characteristics such as solubility, hardness, specific gravity, point of zero charge (PZC), etc. (Arnold and Warren, 1974; Deng et al., 2016; Deng et al., 2015; Ozcan and Bulutcu, 1993a; Yongxin and Changgen, 1983). The conventional collectors used in the flotation of scheelite ores are generally fatty acids or fatty acid derivatives (Bo et al., 2015; Oliveira and Sampaio, 1988; Shi et al., 2014; Sivamohan, 1988; Yongxin and Changgen, 1983). It is difficult to separate scheelite, especially from calcite, with these reagents because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface (Atademir et al., 1979; Changgen and Yongxin, 1983; Hiçyìlmaz et al., 1993; Hu et al., 2011). Therefore, it is almost impossible to separate them by fatty acid flotation without using any selective depressant. Although oleoyl sarcosine was used as a selective collector in the flotation of fluorite and siliceous scheelite ores (Ozcan and Bulutcu, 1993b; Ozcan et al., 1994), this selectivity is inadequate for a low-grade calcitic scheelite ore. Unfortunately, reagents such as organic colloids (dextrine, starch), quebracho, sodium phosphates, sodium silicate solutions containing polyvalent cations (hydrosols), etc. (Bo et al., 2015; Schubert et al., 1990; Shi et al., 2014; Yongxin and Changgen, 1983), used for calcite depression also depress scheelite to a large extent. Cationic collectors, such as amine and quarternary ammonium (Yang et al., 2015) and collector mixture (Gao et al., 2015) have been used to improve the scheelite flotation. However they have not been applied in industry due to the poor separation from silicate minerals."

Jan 1, 2017

By D J. Alchin

Most of South AfricaÆs high-grade iron ore resources are hosted within a fault-controlled structural basin in rocks of the Palaeoproterozoic Transvaal Supergroup in the Northern Cape Province of South Africa. Iron mineralisation occurs as individual orebodies in fault-bounded basins or as fold-controlled concordant lenses around an unconformity plane above the Kuruman Banded Iron Formation. The Sishen mine near Kathu and the beeshoek mine and Sishen South deposit near Postmasburg lie on the northern and southern border of a major domal structure known as the Maremane dome, respectively. The effects and structural constraints of at least three orogenic compressive episodes and several intermittent extensional episodes on the formation, erosion and preservation of iron mineralisation on the Maremane dome and surrounding environs were investigated. Ventersdorp impactogenal rift basin development at ~2.78 - 2.64 Ga, finalised with the deposition of the volcano-sedimentary Vryburg Formation during the thermal subsidence stage at ~2.64 - 2.6 Ga, and was followed by tectonic quiescence/stability and an extensive marine transgression across the entire Kaapvaal craton. The drowning event led to the formation of a carbonate platform with the deposition of the Schmidtsdrif and Campbellrand subgroups conformably above the Vryburg Formation at ~2.6 - 2.52 Ga. The initiation of distal (to the west of the Kaapvaal craton) off-craton oceanic rifting, causing submarine volcanism and associated hydrothermal activity, led to the deposition of initially manganiferous chert (Wolhaarkop Formation) followed by banded ironstone formations (Manganore Iron/Kuruman Formation) of the Asbestos Hill Subgroup at ~2.52 - 2.46 Ga. Initial passive margin rifting along the N-S oriented western edge of the Kaapvaal craton, initiated at the end of Ghaap Group time (during Koegas Subgroup deposition) at ~2.46 - 2.35 Ga, formed a prominent system of N-S striking, westerly dipping normal faults. Easterly directed crustal compression in post-Ghaap Group time in response to the Kalahari Orogeny (accretion of Rehoboth craton along western edge (Kalahari suture zone) of the Kaapvaal craton at ~2.35 - 2.24 Ma led to the formation of large-scale regional, N-trending F1-folds. Partial to complete inversion of the Koegas passive margin rift system (ie reverse dip-slip reactivation of the N-S striking normal fault system to high-angle reverse faults and dextral strike-slip reactivation of the Ventersdorp rift system developed in the Archaean basement), was followed by uplift, erosion and formation of a regional angular unconformity (Postmasburg unconformity). Uplift was accompanied by deposition of fluvio-glacial sediments of the Makganyene Formation (Lower Postmasburg Group) within an intracratonic peripheral foreland basin setting unconformable above Ghaap Group strata at ~2.35 - 2.24 Ga. Post-orogenic crustal relaxation and rifting caused extensional reactivation of the N-trending Palaeoproterozoic passive margin rift system and NE-trending Neoarchaean Ventersdorp impactogenal rift system, forming a fault-controlled depository for the volcano-sedimentary Upper Postmasburg Group at ~2.24 - 2.1 Ga. Deceleration in rifting was succeeded by thermal subsidence of the Upper Postmasburg Group rift, erosion, formation of a regional angular unconformity and deposition of clastic sediments of the Lower Olifantshoek Supergroup unconformable above Postmasburg Group strata at ~2.1 - 1.93 Ga. Renewed rifting led to the deposition of volcano-sedimentary units of the Upper Olifantshoek Supergroup within a rift system superimposed on the Postmasburg Group rift depository at ~1.93 - 1.83 Ga. Easterly directed crustal compression during the Kheis Orogeny at ~1.83 - 1.73 Ga led to renewed inversion of rift structures of the Postmasburg Group and Olifantshoek Supergroup depository, N-trending F2 folding and thin-skinned thrusting of older rock units eastwards over the cratonic cover, thereby utilising planes of weakness in the strata such as prominent unconformities and lithological contrast boundaries as principal dTcollements. NNW-directed crustal compression in response to Lomanian (Namaqua-Natal) Orogeny at ~1.15 - 1.0 G along the southern margin of the Kaapvaal craton, resulted in minor sinistral strike-slip reactivation of the N-S striking fault system, the formation of extensional NNW-SSE striking fracture/fault zones and the development of ENE-trending F3 folds forming a F2/F3 fold interference pattern. Post-Lomanian tectonic events (eg the Pan-African Orogeny at ~650 - 500 Ma, the Cape Orogeny at ~310 - 240 Ma, and the Gondwana breakup at 205 - 120 Ma), caused only comparatively minor extensional reactivation of the pre-existing fault systems. Iron mineralisation was ultimately preserved from erosion by Kheis Orogeny-related N-trending F2 synclines and Lomanian Orogeny-related ENE-trending F3 synclines, in particular areas of interference between F2 and F3 synclines representing comparatively deep semi-circular trough- like depressions, as well as in half grabens formed adjacent to reactivated westerly dipping N-S normal faults. Support for relating the iron and manganese mineralisation to structurally controlled hydrothermal fluid flow during the Kheis orogenic event has also been found, and ongoing research is aimed at confirming and refining the hydrothermal model for iron ore mineralisation in the Northern Cape.

Jan 1, 2007

By M. G. Bakker, D. D. Murphy, D. R. Spears

The US Bureau of Mines studied the mechanism of shear flocculation of silica with stearic acid. At pH 6 and 12, shear flocculation of silica was not observed with the addition of up to 4.5 x 10-4 M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations = 10-4 M (22.5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labeled with a doxyl group. The presence of the spin-labeling group did not greatly affect the shear flocculation properties of stearic acid. Adsorption of labeled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicated that the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-5 M (22.5 lb/st). The results are discussed in terms of a possible mechanism for shear flocculation.

Jan 1, 1995

By D. D. Murphy

The Bureau of Mines has studied the mechanism of shear-flocculation of silica with stearic acid. At pH 6 and 12, shear-flocculation of silica was not observed with up to 10-4M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations 10-4 M (5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labelled with a doxyl group. The presence of the spin-labelling group did not greatly affect the shear-flocculation properties of stearic acid. Adsorption of labelled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicate the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-414 (5 lb/st). The results are discussed in terms of a possible mechanism for shear-flocculation.

Jan 1, 1993

By F. Dehghani, M. Kebe, H. Askari-Sabzkoohi, T. Ghosh

The depletion of bauxite reserves around the world has necessitated the search for viable alternative sources of aluminum. The major non-bauxite source of aluminum is alunite [KAl3 (SO4)2(OH)6]. Lixiviation is the common industrial process to recover aluminum from alunite. Due to the presence of quartz (40%) as the main gangue mineral, this process causes the formation of Sodium aluminosilicate and Potassium aluminosilicate complexes that leads to loss of alunite, and chemical reagents. Thus, pre-concentration of alunite is required to remove the gangue minerals. Because of the low degrees of freedom (DOF) of alunite, froth flotation, as a preconcentration method, is a viable alternative to increase selectivity in downstream processes. In this work, the possibility of Alunite preconcentration with micro flotation and mechanical flotation cells was studied. The influence of type and dosage of collector, pH, solid percent, particles sizes were considered on the flotation. Flotation tests were designed based on Taguchi method, followed by performing based on surface charge differential between alunite and quartz on direct and revers flotation. In the reverse flotation, Ca+ 2 and Ba+ 2 were used to activate the quartz surface. Under optimum conditions of reverse flotation, alunite grade and recovery were 40% and 62.1% respectively. In the direct flotation, the surface of alunite was activated by F- . The grade and recovery were 50 and 89%, respectively.

Mar 2, 2022

By M I. Pownceby, N A. S Webster, J R. Manuel, J M. F Clout, E Donskoi, N A. Ware

The relative influences of sinter mineralogy, sintering temperature, solid and pore macro- and microstructure on iron ore sinter physical strength are not yet fully understood. Whilst a range of analysis techniques have been used by researchers to evaluate sinter physical properties and sinter mineralogy, none have been able to directly link sinter mineralogy and physical strength under controlled conditions. CSIRO has developed a unique laboratory method to study the fundamental melting properties of fine iron ores in a laboratory furnace under a controlled temperature and gas atmosphere environment designed to simulate the industrial sintering process. Compacted tablet samples for a 0.41 per cent and a 2.5 per cent Al2O3 series were fired in a tube furnace at various temperatures, cooled, then tumbled using a modified Bond abrasion test apparatus to determine a relative tumble index (TI) at each temperature. Quantitative XRD (QXRD) analysis was then carried out on the tumbled samples and optical image analysis (OIA) was conducted on polished sections of a separately fired compact in each case. The amount of total SFCA was found to decrease with increasing firing temperature for both alumina series with the total amount of SFCA higher in the 2.5 per cent Al2O3 series compared to 0.41 per cent Al2O3 series samples. The increase in the amount of magnetite and hematite with increasing firing temperature was largely at the expense of a decrease in total SFCA. Overall, there was good agreement between the quantitative mineralogy determined from QXRD versus OIA for SFCA, hematite and magnetite. Qualitative analysis of high magnification images of the sinter correlated with both the OIA and QXRD results.

Sep 18, 2023

By Julie Hunt

Rimfire Minerals Corporation: early stage precious metal exploration specialists with discovery opportunities in partnership with major and mid-tier gold producers or prominent junior exploration firms. Mike Roberts, Senior Geologist

May 1, 2006

By Thomas Kuhn

Germany?s industry heavily depends on the continuous import of mineral commodities such as manganese, copper, nickel, and molybdenum. Due to the strong increase in metal prices since 2002 Germany?s federal geological survey, the Bundesanstalt für Geowissenschaften und Rohstoffe (Federal Institute for Geosciences and Natural Resources, hereafter called BGR) applied for a license area for the exploration of deep-sea manganese nodules in the Pacific manganese nodule belt between the Clarion and Clipperton fracture zones. A 75,000 km2 covering license area was eventually granted to the BGR by the International Seabed Authority (ISA) in 2006. It is separated into two parts: ?W1? (17,000 km2) and ?E1? (58,000 km2; Fig. 1). The BGR obtained initial information on the abundance and grade of nodules in the license area from samples collected during three cruises with R/V Valdivia and one cruise with R/V Sonne between 1976 and 1978 (Rühlemann et al., 2009). Since the accuracy of navigational data obtained during these cruises is outdated and sample coverage is unevenly distributed and sparse in many parts of the license area, BGR has started a new exploration program to investigate the German license area according to the rules, regulations and procedures issued by the ISA for the exploration of Mn nodules in the Area.

Jan 1, 2010

By Andrew Z. Boeckelmann, David S. Graham, Paul J. Axtell

In the last fifteen years, several research studies have evaluated the ability to detect various types of deep foundation concrete integrity flaws with crosshole sonic logging (CSL) and thermal integrity profiling (TIP). This paper synthesizes the findings from the research, focusing on two studies that included CSL and TIP testing of drilled shafts with various types of flaws. The first, a 2016 research study of test shafts for the Wisconsin DOT, included inclusions inside and outside the reinforcing cage, intentional tremie withdrawal during concreting, and soft bottom flaws. The second, a 2021 study of production shafts for the Missouri DOT, included one shaft with and another without soft bottom conditions. After synthesizing the ability of each test method to detect each type of flaw, the paper presents recommendations for improving how CSL and TIP results are evaluated in practice. The recommendations highlight DFI‟s CSL interpretation protocol as well as the importance of evaluating TIP data versus time, not just depth. The paper includes example temperature-versus-time plots for various types of flaws and emphasizes how temperature-versus-time evaluation can be used to distinguish soft bottom conditions from standard bottom-of-shaft temperature roll off.

Oct 1, 2022

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987