Search Documents

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.' Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution. ALTHOUGH cyanide solvents are used very ex-x*. tensively for the recovery of gold from ores and concentrates, the normal rate of solution of the precious metal as determined by Barsky, Swainson, and Hedley,1 and others2 is less than about 3 mg per sq cm of exposed gold surface per hour, corresponding to a corrosion depth of approximately 1.5 microns (0.00006 in.) per hr. Although the slow rate may be increased to some extent in certain cases, as, for example, when the the gold is partially imbedded in iron pyrites,3 the leaching operation is generally the most time-consuming step of the cyanide process. Frequently it is necessary for the leaching solvents to remain in contact with the ores for 50 to 200 hr in order to dissolve all of the gold particles.' Not only does the slow solution rate cause some increase in the capital costs, but the cyanide consumption also may be increased because of vaporization of hydrocyanic acid and secondary reactions with minerals such as malachite (CuCO3 • Cu(OH)2), and pyrrhotite, which often are associated with gold. It is not surprising that numerous attempts have been made to accelerate the dissolution of gold in cyanide solutions. Experimental Gold Leaf Test: The gold leaf test was apparently originated by M. Faraday, who, by means of it, discovered that dilute cyanide solutions would dissolve gold readily in the presence of oxygen. The usefulness and reliability of the test have been discussed elsewhere.5,6 Essentially, the method consists of determining the time required for 5-ml portions of cyanide solvents to dissolve squares of 23 carat gold leaf, 0.5 cm on edge, when shaken in 10-ml test tubes with the solvents. The weight of gold leaf per test was 0.051 mg as determined by the direct weighing of a leaf 8.6x8.6 cm (weight = 15 mg) and measuring the area of the test sample (0.25 sq cm). Gold leaf is of remarkably uniform thickness.6 Since gold leaf, like native gold, contains small amounts of copper and silver, the results are comparable with those one might expect in cyaniding gold ores. As six or more tests can be made simul- taneously, the relative efficiencies of the solvents can be evaluated readily. All dilute solutions of lead, bismuth, thallium and mercury salts were prepared by the ordinary dilution method used by chemists. Our C.P. sodium cyanide and buffering reagents had no detectable amounts of either sulphide ion or heavy metals. Soluble Sulphides in the Cyanide Process: The action of soluble sulphides is of interest in the study of the dissolution of gold in cyanide solutions. That gold ores which contain compounds of arsenic and antimony often are not amenable to direct cyanide treatment is well known, and it said that arsenic and antimony are "cyanicides."7 It is commonly believed that part of the sulphur content of such ores is soluble in alkaline solutions to give sulphide ion, which reacts with the free cyanide content of the leaching solutions to form inert thio-cyanates or reacts with the dissolved oxygen to form sulphites or sulphates.8 A purpose of this paper is to demonstrate that sulphide ion may behave in a manner that cannot be explained by either the oxygen-depletion or thiocyanate formation theories and to prove directly that concentrations of sulphide ion which cannot be detected even by colorimetric methods may retard the dissolution of gold.

Jan 1, 1951

By E. M. Tory, P. T. Shannon

An analysis of batch and continuous thickening in terms of the movement of planes of constant concentration (i.e. continuity waves) is presented. Use of solids flux as a primary variable greatly facilitates the analysis and clarifies the relationship between batch and continuous thickening. An "ideal" slurry is defined as one whose settling rate is a function only of the local solids concentration. An analysis of continuous thickening of this ideal slurry in an ideal thickener explains many aspects of the steady — and unsteady — state behavior of real slurries, such as the main features of a thickener's "solids profile" (including the break attributed to rake action), the sudden appearance at abnormally high feed rates of a zone of constant concentration and the velocity with which it rises, and the effect of detention time at constant weight of sludge per unit area. Where deviations exist, they are explained in terms of the batch settling behavior of real slurries. The purpose of this paper is to interpret continuous thickening phenomena in terms of batch settling behavior. Both types of thickening may be considered as the process of propagating concentration changes, due to the downward movement of the solids, from the bottom of the settling vessel upward through the slurry.' These concentration changes may be either finite or infinitesimal as in the case of the propagation of a continuous concentration gradient. The slurry itself may be moving downward as in the case of continuous thickening. The downward velocity of the slurry may be such that the concentration changes being propagated up from below remain stationary relative to the thickener walls. This is the case for steady-state thickening. It seems appropriate to analyze continuous thickening in terms of the movement of planes of constant concentration. This has already been done for batch settling."3 Although our main interest is in real slurries, there are certain aspects of both types of settling which can be deduced from a theoretical analysis of highly idealized systems. To this end, an "ideal slurry" is defined as one for which the dimensionless settling rate at any point is a function only of the local solids concentration.1,2 An "ideal thickener" is one in which there is no radial variation in either the solids concentration or in the downward component of slurry velocity. The underflow outlet is a point sink. It is to be expected that the behavior of non-ideal systems will deviate in some measure from theoretical results. However, the same characteristics which cause deviations in continuous thickening should be evident in batch settling, permitting a rational explanation of the former in terms of the latter. PREDICTED RESULTS FOR AN IDEAL SLURRY IN AN IDEAL CONTINUOUS THICKENER General Theory: In continuous thickening, the downward solids flux (mass/area-time) relative to the thickener, G, results from two different

Jan 1, 1967

By Robert C. Emmett, Donald A. Dahlstrom

FOR many years gravitational classification has been employed as a basic tool in beneficiation of minerals and coal. While improvements have been made to increase efficiency and fields of application, the basic flow pattern has remained relatively unchanged in most gravitational classifiers. Feed slurry is introduced into a settling pool wherein the coarser solids settle against either an upward or horizontal fluid current, or a combination of both, and are withdrawn in a concentrated underflow stream. The finer solids below the classification point possess too low a settling velocity and thus are primarily swept out through a weir overflow by the bulk of the fluid. Because of its simplicity, efficiency, and low power and maintenance costs, gravitational classification finds a wide acceptance for separations in the range of 20 to 325 mesh. Two factors resulting from the basic flow pattern employed in gravitational classification present difficult problems for certain installations. If classification at 60 to 200 mesh of separation is desired, capacity in terms of gallons of overflow per minute per square foot of settling pool area must be low to allow required solids to settle to the underflow. If a thousand or more gal per min of feed slurry must be handled, either a very large classifier or a number of smaller units must be employed, taking up floor space and head room. Examples of this are the large classifiers, wetting tanks, or settling tanks used in the coal industry for recovery of process water from fine solids. Units as large as 50 or 60 ft in diam and 60 ft high, requiring substantial amounts of steel, are not uncommon. A second factor is the lack of self-regulation in gravitational classification. As overflow rate increases, mesh of separation increases correspond-ingly. This normally heightens difficulties of bene-ficiation. If a fine mesh of separation is required at varying feed rates, the problem is more than doubled in complexity. One of the primary advantages of gravitational classification is low power requirement. Gravity feeds or very low pressure heads are employed. However, fluid energy is still present in the inlet stream and provision must be made to dissipate it properly to obtain uniform upward or horizontal currents. Rather than waste this energy, it would be desirable to utilize it to secure a greater degree of self-regulation and simultaneously increase classification capacity per square foot of area. A free vortex could be realized by a tangential entry of feed, resulting in generation of centrifugal force to complement force of gravity in its action. With greater force it should be possible to gain finer separation at any overflow rate per square foot of settling pool area as compared with conventional gravitational classification. Furthermore, as feed rate increases, centrifugal force will also increase and at least partially offset faster currents sweeping solid particles to the overflow. A more stable classification point should result. The liquid-solid cyclone is the most common application of a free vortex in the beneficiation field.' Many previous papers have emphasized uniformity of flow pattern within the cyclone which is largely responsible for the sharp classification that can be obtained.'-4 If a free vortex can be maintained in a non-pressurized vessel with a free surface it may be possible to realize a third advantage of sharper classification. This open-top cyclone would then achieve a minimum energy loss comparable to that with conventional classifiers, and a mesh of separation coarser than 150 mesh, extending the range of application of the free vortex. This is not presently possible with ordinary cyclones. To test the applicability of the free vortex to gravitational classification, a 30-in. diameter open-top cyclone was constructed at Northwestern University. The cylindrical section was 30 in. high and the conical section included an angle of 60". The feed nozzle was a standard 4-in. pipe entering tan-gentially, with centerline 17 1/2 in. below the top of the cyclone. The conical section was flanged near

Jan 1, 1954

By C. C. Harris

The characteristics of some common size distribution equations are critically discussed. A generalized form of several well-known size distribution equations is obtained from a differential equation describing statistical distributions. The equation contains three parameters and can describe the major features of size distributions in the fine and the coarse size regions. A graphical method for its implementation is provided. The application of this and other equations to sets of data are compared both for the quality of fit and from a comminution kinetics viewpoint. If a narrow size range of a brittle material is broken sufficiently to obliterate the feed sizes, but not so severely that excessive secondary breakage occurs, a plot of cumulative fraction by weight undersize (Y) vs. sieve size (X) on a log log grid (sometimes called the Gates-Gaudin-Schuhmann plot)1-3 gives a straight line of slope ~ 1 over much of its range. On closer inspection, deviations in the extreme coarse range covering perhaps 10 to 30% of the total sample may be apparent (frequently, a change in slope from ~ 1 to a value different from unity) together with over-all slight irregular departures from a smooth line. One model of breakage postulates that the same fracture pattern persists throughout all size ranges.4 The fracture pattern is characterized by the slope of the line on a log log grid. Accordingly, a distribution of sizes broken in the manner specified earlier is expected to produce a size distribution having the same slope as that of a broken narrow size range. Additionally, the slight irregularities mentioned above should even out in the summation process, giving a smooth straight line of slope ~1 on a log log plot. This idealized state of affairs does not, however, describe the distribution of a multi-event process such as that for a tumbling mill product. On the average, these curves (plotted again log log) tend to have a slope in the fine region different from and usually less than unity,5 while the coarse size region curves with increasing slope for cases of mild reduction, and with decreasing slope when moderate or severe size reduction has occurred. In addition, there are usually slight irregular deviations from a smooth curve. Most curves display two distinct regions — fine and coarse — and a few curves show one or more intermediate regions. Feed size studies6,7 show an effect which theory is required to explain. For the same material, mill loading and other operating conditions, and the same time of grinding, plotting the dimensionless ratios Y vs. X/(feed size) does not reduce the size distribution data to the same curve. Y vs. X does not correlate the coarse region, but it can provide a crude correlation of the fine region which improves as size diminishes and as grinding time increases. The size distribution in the coarse region is somewhat more dependent on the feed size than is the distribution in the fine region wherein the degree of dependence diminishes as time proceeds; the distribution of sizes in the fine region are determined largely by the nature of the material and the comminution conditions. A comprehensive model of comminution must recognize that several different patterns or modes of breakage can occur in a mill; 5,8,9 that there can be some selection in that some size ranges are broken more than others; and that, while some particles may be the product of a single fracture event, or may even remain unbroken, others result from multiple rebreak-age. Thus, breakage in a tumbling mill is more complex than the Schuhmann4 model admits in that several different types of comminution micro-events* occur rather than just one type, and these events, though different in size scale, are of the same overall pattern as that which is visualized by the model. The concept of an average comminution micro-event has, therefore, a mathematical rather than a physical connotation, at least for tumbling milling. Equations with which to describe particle size distributions have been sought for over half a century.10-13 No equation presently in general use was first derived from an analysis of the statistical mechanics of breakage; whatever theoretical basis the existing

Jan 1, 1969

By J. E. Lawver, J. L. Wright, H. R. Kokat

Mesabi semitaconite and oxidized taconite ores that cannot be concentrated by froth flotation can be rendered amenable to flotation through partial concentration in a high-in tensity wet magnetic separator. Since 1964, a method for accomplishing this precon-centration has been under development at the Minnesota Mines Experiment Station, where several hundred tons of ore have been successfully processed. This paper is an analysis of the performance of the separators used at the Station. At present the United States is producing about 85 million tons of iron ore a year, and nearly 55 million tons of this comes from Minnesota. Nearly half of Minnesota's production is in the form of magnetite taconite pellets —the remainder being wash ore and gravity concentrates. As the demands of the blast furnace operators become more stringent - and they are becoming more so yearly — these demands are met by improved iron ore beneficiation technology. Furthermore, there is no doubt that as magnetite taconite, gravity ores, and wash ores are exhausted, new processes will be developed to produce a product comparable to magnetite taconite pellets from Minnesota's vast reserves of oxidized taconite and semitaconite. The magnetite taconite ores are rather easily bene-ficiated by conventional, low-intensity (500- to 1400-gauss) magnetic separators, followed, in some plants, by froth flotation of the magnetic concentrates.

Jan 1, 1969

By A. Y. Bethune, W. G. Woolf

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By W. G. Woolf, A. Y. Bethune

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process' for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt's earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.'s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By C. H. Snyder

Tlie paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented. THE various units used in conventional mining are well-built. Generally the universal under -cutter, driven by approximately 50 hp, weighs approximately 25,000 lb, and is a very strong piece of machinery. The drilling machine is not as husky as an undercutter, generally is driven by approximately 15 hp, weighs about 9000 lb, but is a well-constructed, sturdy mechanism. The loader, usually 60 hp, weighs approximately 24,000 lb, and certainly is a strong, rugged unit. The working parts of all three of these sturdy conventional units have been made of tough steel alloys for some time. With the use of three machines having a combined horsepower of approximately 125, with a combined weight of approximately 60,000 lb, and with the possible inherent advantage of single purpose machines performing a single function, the use of considerable explosives has been required to complete the conventional mining cycle. It was therefore our thought, upon conception of the first Colmol,* a machine which was to do the work accomplished by the three conventional units plus explosives, that it must be a rugged mechanism. Now, after building several units, after going through many and varied experiments, and after the expense of some million-odd dollars, we find we have observed and learned nothing that contradicts our original thinking. A continuous miner, if it is to give satisfactory performance, must be a rugged piece of machinery. Ruggedness has been, and is constantly, in the minds of our engineers in designing the Colmol. Improvements where they have been required have been in the direction of more weight, more horse power, better alloys, bigger hydraulic pumps and motors; in short, always, toward more torque, greater strength, more ruggedness. Now not only the finest steel alloys are utilized but more than 100 Timken roller bearings are used. The following is some pertinent data on models being built and to be built: The low unit: Cutting height, 30 to 42 in. By changing the upper gear case the maximum cutting height can be increased to 61 in., giving a variable cutting height of from 30 to 61 in. Width of cut, 9 ft 6 in. Width of body, 75 in. over tracks. Height of body, 271/2 in. Overall length, 23 ft. Driven by three 50-hp motors or a total of 150 hp. Weight, 26 tons. The intermediate unit: Cutting height, 451/2 to 72 in. Width of cut, 9 ft 8 in. Width of body, 77 in. over tracks. Height of body, 43 in. Overall length, 26 ft. Driven by three 70-hp motors or a total of 210 hp. Weight, 35 tons.

Jan 1, 1951

By C. H. Snyder

Tlie paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented. THE various units used in conventional mining are well-built. Generally the universal under -cutter, driven by approximately 50 hp, weighs approximately 25,000 lb, and is a very strong piece of machinery. The drilling machine is not as husky as an undercutter, generally is driven by approximately 15 hp, weighs about 9000 lb, but is a well-constructed, sturdy mechanism. The loader, usually 60 hp, weighs approximately 24,000 lb, and certainly is a strong, rugged unit. The working parts of all three of these sturdy conventional units have been made of tough steel alloys for some time. With the use of three machines having a combined horsepower of approximately 125, with a combined weight of approximately 60,000 lb, and with the possible inherent advantage of single purpose machines performing a single function, the use of considerable explosives has been required to complete the conventional mining cycle. It was therefore our thought, upon conception of the first Colmol,* a machine which was to do the work accomplished by the three conventional units plus explosives, that it must be a rugged mechanism. Now, after building several units, after going through many and varied experiments, and after the expense of some million-odd dollars, we find we have observed and learned nothing that contradicts our original thinking. A continuous miner, if it is to give satisfactory performance, must be a rugged piece of machinery. Ruggedness has been, and is constantly, in the minds of our engineers in designing the Colmol. Improvements where they have been required have been in the direction of more weight, more horse power, better alloys, bigger hydraulic pumps and motors; in short, always, toward more torque, greater strength, more ruggedness. Now not only the finest steel alloys are utilized but more than 100 Timken roller bearings are used. The following is some pertinent data on models being built and to be built: The low unit: Cutting height, 30 to 42 in. By changing the upper gear case the maximum cutting height can be increased to 61 in., giving a variable cutting height of from 30 to 61 in. Width of cut, 9 ft 6 in. Width of body, 75 in. over tracks. Height of body, 271/2 in. Overall length, 23 ft. Driven by three 50-hp motors or a total of 150 hp. Weight, 26 tons. The intermediate unit: Cutting height, 451/2 to 72 in. Width of cut, 9 ft 8 in. Width of body, 77 in. over tracks. Height of body, 43 in. Overall length, 26 ft. Driven by three 70-hp motors or a total of 210 hp. Weight, 35 tons.

Jan 1, 1951

By Edward Martinez

The reactions occurring in the copper segregation process were studied by heating mixtures of chryso-colla, salt, and a reducing agent. The techniques used in this investigation were differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). The initial chloridizing of the oxide copper occurs below 500°C and cupric chloride may be the compound formed. Volatilization and reduction of the copper chloride take place above 550°C, although these reactions do occur to some extent below 550°C. A difference in the distribution of the metallic copper in the reducing agent was found when sodium chloride was used compared to magnesium or calcium chloride. Segregation was obtained with mixtures of cupric oxide, salt, and charcoal with no quartz or silicate present. Preliminary tests indicate that segregation may occur even in the absence of water vapor. The DTA and TGA techniques were found to be of great value in studying these reactions. The copper segregation process is a method for treating oxide copper ores. The ore is heated, most commonly in a kiln, with a reducing agent and a halide salt, generally sodium chloride, to approximately 700°-750°C and held for 30 to 60 min. The addition of the salt results in the migration and reduction of the oxide copper to metallic copper on the surface of the reducing agent rather than in the original mineral structure. The metallic copper can then be recovered by a subsequent leaching or flotation step.1-4 Experimental work in 1923 on oxide copper ores from the Sagasca mines in Chile led to the discovery of the reduction process. It was found that during the reduction of the copper mineral with coal, at about 700°C, the copper migrated to the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge. The ratio of salt to reducing agent may vary somewhat, but in general 0.5% to 1.5% sodium chloride and 0.5% to 1.0% coal or coke have been mixed with the ore. Less than stoichiometric amounts of salt are required to convert all the oxide copper to a chloride, so that a cycle of reactions appears to be occurring. Several investigations reported in the literature have proposed reactions to explain the mechanism of the process.5-10 There appears to be general agreement that water is necessary for the reactions to occur; that once the sodium chloride reacts with silica or silicates in the ore, the hydrochloric acid formed will convert the cupric oxide in the mineral structure to cuprous chloride. However, there appears to be a conflict of opinion on the reactions involved in the reduction of the cuprous chloride to metallic copper on the surface of the carbon. Rey has indicated that salt, water vapor, and

Jan 1, 1968

By J. Steininger

The Hallimond tube flotation of sphalerite and pyrite with sulfhydryl collectors has been found to be inhibited near neutral pH in the presence of copper salts. Alkalimetric titration studies of the reactions between collector and activator indicate that this effect is apparently related to the formation of basic copper collector complexes. The conditions of formation of these compounds and their stability are in good agreement with the depression observed in flotation experiments. The general procedure employed in the flotation of zinc sulfide minerals requires activation of the mineral surface by heavy metal ions, usually copper, which react more easily than zinc with the common short-chain ionic sulfhydryl collectors.' Commercially, zinc flotation is carried out under alkaline conditions (pH 7 to 10.5), but small-scale experiments indicate that zinc sulfide minerals can also be activated and collected under acid conditions. Selectivity, however, becomes poor at low pH and undesirable materials such as pyrite, silicates and carbonates tend to report in the float. Several years ago, Wark and Sutherland~, measured the contact angles of air bubbles on copper-activated sphalerite immersed in various sulfhydryl collector solutions. When represented, as in Fig. 1, on pH-sodium cyanide diagrams, the results are characterized by 'islands' of non-contact near neutral pH and

Jan 1, 1969

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By K. E. Merklin, F. D. DeVaney

In the past most of the research in pelletizing has as its aim the production of a physically strong pellet. Now that this problem is solved, more attention is being paid to uniformity in grade and chemical composition. Consideration has been given in recent years to a study of additives which will make pellets partially or fully fluxed. Blast furnace tests show fluxed pellets to have advantages over both fluxed sinter and acid pellets. Lower slag volumes are used more frequently in the blast furnace and the uniformity of the charge, both physically and chemically, is becoming increasingly important. A considerable improvement can be secured by having all of the flux uniformly distributed through the pellets in a calcined state. A fluxed pellet, therefore, should be a superior product. The use of an ore burden that contains an appropriate quantity of fluxing materials is not new to the blast furnace industry. For years the Minette ores of France and Germany, the Clinton ores of the Birmingham, Ala., areas, as well as others, which are low in iron but contain calcium carbonate in sufficient quantities to give them self-fluxing properties, have proven economical. The adaption of the sintering process to the preparation of ore burdens provided a means for artifically associating the fluxstone with the iron ore prior to charging to the blast furnace. In 1944 Torpl discussed the effects of using lime in sinter made in Sweden on the sinter's metallurgical performance in a blast furnace. Hessle2 reported in 1945 on the advantages of using lime in sinter to increase the sintering plants' capacity and reduce fuel requirements. Robinson3 discussed the use of lime in Swedish sintering practice at the 1950 Blast Furnace, Coke Oven, and Raw Materials meeting. One of the suggested advantages was the combining of lime with silica to prevent the formation of a fayalite slag, which is difficult to reduce in the blast furnace. Nilson4 at the same meeting commented briefly on experimental work that had just started in the U. S. on the use of lime in sinter. The literature tends to indicate that most of this early work was directed towards improvement in sinter physical quality, and the fact that the feed to the blast furnace was partially fluxed was incidental. It was not long, however, before blast furnace advantages were being claimed. The matter was forcibly called to the attention of North American operators by reports of remarkable production records established by the Russians using fluxed sinter. The leading step was taken on this continent by the Steel Company of Canada in 1957; McMahon5 reported on the marked improvement in performance of an 18-ft blast furnace using fluxed sinter at its Hamilton works. Other North American operators quickly followed theStelco lead.

Jan 1, 1963

By Vernon F. Swanson

An equation has been developed which will permit the direct determination of free settling velocity of any sized particle encountered in mineral benefici-ation. The equation is based on Newton's Law with the friction factor defined as a function of the laminar boundary layer. Development of the equation is described first from an empirical trial-and-error approach. Examples are given of actual settling data from the literature versus calculated data to prove the validity of the new equation. Newton's law of resistance of a fluid to flow around a sphere is expressed in Eq. 1. Free settling velocities can be determined by setting Eq. 1 equal to the gravitational force on a particle and solving for V. Experience has shown that when the solids are greater than 1 mm in diam, or when Reynold's number for the system is greater than 800-1000, the friction factor term, fD, essentially becomes a constant, and Eq. 2-b becomes Newton's equation for free-settling and is applicable under the conditions stated. Another special condition exists for particles smaller than 0.05 mm or when Reynold's number for the system is less than three. In this case fD=24/NRor24µ/pL,dV,. Eq. 2-b can then be rewritten as

Jan 1, 1968

By H. Evans, L. A. Hunt

The raw materials used in the blast furnaces at the Geneva Works of U.S. Steel Corp. have a high degree of variability in size-consist and chemical content. To overcome the problems caused by the use of highly variable raw materials in the blast-furnace operation, large blending piles are used. An investigation of the blending system showed that variability was significantly reduced by the use of these blending piles. This paper describes the blending system, the method used to evaluate the effect of the blending system, and the results of the investigation. The remarkable improvement in blast-furnace performance since World War II has been in large measure due to the use of beneficiated burdens to reduce the variation of both chemical analysis and size consist. This practice allows the operator better control of his blast furnace, enabling him to operate more economically and to produce chemically uniform hot metal. Planning for uniformity usually begins during mining by extracting ore from several locations within a pit to produce a final product with a specified analysis. Another approach is to stockpile ores having widely varying analyses in individual piles and then drawing the required amounts from each stockpile to provide a blend with a predetermined analysis. A further improvement in blending procedures is to take ores from several sources, bedding them horizontally in layers and reclaiming by vertical slicing from the blended pile. The last procedure, when properly executed, is one of the best methods for achieving maximum uniformity with highly variable ores. U.S. Steel Corp.'s Geneva Works initially obtained iron ore for their blast furnaces from the Cedar City area of southern Utah. These ores were formed primarily by the replacement of limestone and siltstone formations with solutions containing iron and several other elements. The original iron content of the ores in the ground varied from a high of 70% to practically zero with a minimum acceptable iron content for shipping of 37%. Substantial amounts of silica, calcium, magnesium and alumina were found in the ores along with minor amounts of copper, lead, zinc, nickel, titanium, manganese, phosphorus and sulfur which were sometimes present in detrimental amounts. Iron-to-silica ratios varied considerably throughout

Jan 1, 1968

By Gordon E. Agar, David M. Hopstock

This paper describes the procedures and results of a series of experiments conducted to determine the depressing effect of sodium, calcium and magnesium ions on the amine flotation of quartz. It also presents an analysis of the experimental results by the electrical double layer theory. The flotation of quartz with primary amines has been practiced on a large scale in the phosphate industry for many years. Some glass sand —and recently iron ore — has also been treated by this flotation technique. These applications have been highly successful and demonstrate that a complete mastery of all the details of an operation is not needed to achieve an economic success. There are times, though, when it becomes important to recognize, both qualitatively and quantitatively, the effects of some previously ignored variables. The effects of cations on the amine flotation process, particularly those ions that contribute to water hardness and abound in sea water, are a case in point. In conjunction with the development of a cationic flotation reagent for separating quartz from apatite, it became necessary to quantify the influence of calcium and magnesium on the separation. In order to strengthen and broaden current understanding of the flotation process, the results were interpreted by means of the electrical double layer theory. THEORETICAL BACKGROUND Assume that, given the same equipment, procedure, and time, the recovery of quartz by amine flotation is a function of only the adsorption density of aminium ions in the Stern layer, i.e., that for any given adsorption density there exists only one recovery percentage. By the Stern-Grahame treatment of the electrical double layer,'-' for any ionic species in a solution in equilibrium with quartz,

Jan 1, 1969

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.' In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By R. C. Ferguson, Harlowe Hardinge

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951

By Harlowe Hardinge, R. C. Ferguson

Laboratory and plant data covering 12 different operations show that lower than "standard" ball mill speeds increase grinding efficiency. In the case of high pulp-level mills, the gain is so great that the increase in capital cost of the larger lower speed mill will pay for itself in less than a year's time. THE object of this paper is to show the economic advantage of operating ball mills at relatively slow speeds. Although many operators know that grinding costs are reduced by operating mills at low speeds, they seldom do so for a variety of reasons. When capital is limited, first cost is of primary importance, and installation of the less costly, highspeed mill is favored. When materials are in short supply, as during a war period, capacity rather than economy is the primary consideration. Existing mills are then speeded up to provide the desired increase in capacity, and new mills are purchased without consideration of maximum grinding efficiency. When the mill speed is increased to secure more production, the increase in grinding costs is often obscured by the total benefit derived from the additional output. This increase in grinding cost is seldom recognized as being sufficient to be worth correcting. For these reasons one may be lead to the erroneous conclusion that slow-speed operation is only occasionally applicable. The effect of mill speed on grinding efficiency has been studied in laboratory tests."! The results of some of these tests are given in tables I and I1 and fig. 1. In these tabulations, batch tests using ore charges of 125 to 200 lb were considered comparable to high pulp-level operation and charges of 50 to 100 lb comparable to low pulp-level operation. For the high pulp-level operation, these tests indicate the existence of a maximum in efficiency for operation at a speed of 50 pct of critical, both for the soft (dolomite) and hard (chert) ore. In low pulp-level operation, a decrease in speed increases the efficiency of grinding dolomite; no maximum of efficiency appears in the range of speeds tested. The results with chert were inconclusive. If the performance of large mills is indicated

Jan 1, 1951