Search Documents

By E. J. Roberts, E. B. Fitch

THE mechanism of classification by settling pools is most simply shown in the case of batch sedimentation such as was analyzed by Oden.1 The batch model will be considered, therefore, and it will be shown that the same mechanism applies to continuous operation. Classification in Batch Settling Pools: Consider a beaker or tank of slurry containing particles so dispersed that they can settle independently of one another under the influence of gravity. Originally all particle sizes are uniformly distributed throughout the suspension. All particles start immediately to settle towards the bottom at rates determined by their size, shape, and density—among other factors. Particles reaching the bottom settle out of suspension. After some given time the slurry above the deposited solids is siphoned off or otherwise removed, leaving the deposited solids behind. The deposited solids, together with entrained and any unremoved supernatant slurry, represent the underflow of a classifier. The slurry removed represents the overflow. There is a certain separation, size of particle which during the sedimentation has just time to settle from the top surface of the slurry to the level at which underflow and overflow are parted. All particles with a faster settling rate will have dropped to below this level, no matter where in the beaker they started from originally, and therefore will be absent from the overflow. Particles with a slower settling rate will not reach this level if they started from the top of the slurry, but a portion of them,

Jan 1, 1957

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,' we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany' obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.'r3 In the present investigation, 1:l mix-

Jan 1, 1963

By W. J. Tait, A. E. Craig, E. P. McCurdy

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951

By E. P. McCurdy, W. J. Tait, A. E. Craig

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951

By W. J. Tait, A. E. Craig, E. P. McCurdy

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By E. P. McCurdy, W. J. Tait, A. E. Craig

C. M. Marquard—The problem of the automatic control of a grinding-classification circuit is not nearly as simple as has been indicated and it cannot be universally solved through the application of this device. The sound emanating from a ball mill such as the metallic clink of the balls against the liners can at times be misleading. The fact that the sound level due to the balls hitting the liners may be at a minimum does not necessarily mean that the mill is properly loaded. I have in mind an ore we treat that has a soft talcy gangue. The soft fluffy nature of this material makes the sound from the ball mill a most misleading parameter that is worthless as a means for controlling the amount of ore fed to the mill. In every milling plant there are transportation lags due to the time it takes the ore to travel from the mill bins to the ball mill. In many plants there may be several different transportation lags due to varying distances of bins from ball mill. These transportation lags can most seriously affect the operation of a controller. It has been found that under many circumstances the transportation lags can be so bad as to cause the controller to hunt seriously. Hunting can and in many cases does become so serious as to render automatic control impossible because of the surges it causes. While it is possible to compensate for this type of lag, this apparatus does not lend itself readily to accomplish the required compensation. Further, if there are groups of bins at various distances from the ball mill, compensation for one may not be sufficient or may be too great for another. Each milling plant presents a separate problem. The apparatus as presently described does not appear sufficiently flexible to accomplish this. It should be noted that the load on the classifier rakes is determined by measuring the current input to the rake drive motor. Variations in line voltage will

Jan 1, 1951

By S. A. Falconer

Much attention and publicity has been given, during recent years, to grinding, classification, flotation, and thickening. The various technical papers, and symposiums held to discuss these important phases of milling, have contributed to a better understanding of the fundamental principles and operating variables involved. Another important part of milling— to the flotation operator—is a treatment step to which frequently too little attention is given—"conditioning," or the treatment the ground mineral pulp receives before it enters the flotation machines. "Conditioning" is a hackneyed and frequently misused term, commonly employed to describe the pretreatment of surfaces of minerals in ore pulps or mill products prior to froth flotation. In general, such pretreatment is for the purpose of changing the flotation characteristics of these mineral sur- faces to enable them to respond in some desired predetermined manner when subjected to flotation. Taggartl states that the function of conditioning is "either to insure selective collector coating of one mineral species while another species is not; or to take such steps as will compensate for departure therefrom." As 0. C. Ralston has stated? ... we are still faced with the fact that some mineral particles are water-avid, others air-avid, and that by properly modifying them they may be enhanced or diminished in desirable or undesirable avidity. Coatings on minerals must still be assumed to fall into three classes: (1) a coating of immiscible oil, (2) a layer of adsorbed substance, (3) a chemically produced coating. It is submitted that the process of preparing mineral surfaces for subsequent flotation treatment should take into consideration physical as well as chemical means for altering the normal flotation response of the mineral surfaces. A more descriptive word than "conditioning" is needed to designate broadly these procedures. The minerals in many ores cannot be made to respond in a normal manner to usual methods of "conditioning" with selectivity modifying reagents, until they have been cleansed, or interfering slimes and soluble salts have been removed from the ore. Therefore, it appears important to include under the general subject of "conditioning" a discussion of the purposes, methods used, and some of the advantages of these pretreatment steps. This is dealt with under the subject heading " Initial Treatment of Mineral Surfaces and Ore Pulps." Under this broader interpretation, the methods employed for treating mineral surfaces to alter their flotation characteristics may be divided into three general classes: 1. Physical methods.

Jan 1, 1950

By J. E. Forciea, R. W. Salmi

Operating and research personnel at U.S. Steel's Pilotac concentrator have evolved specifications for magnetic separators suitable for use in beneficiation of Mesabi magnetic taconite. These specifications were developed as a result of investigations into the operating and metallurgical problems at the Pilotac concentrator over a period of some ten years. This paper discusses primary magnetic separator specifications, but much of the information is also pertinent to secondary and tertiary magnetic separators. Of particular significance is the proposal of a new basis for specifying the magnetic field which includes consideration of both field strength and field gradient. Other areas of discussion include flowsheet service, operating conditions such as drum speed and pulp level, tank configuration, magnet strength including field gradient, sleeve bearing design, designation of corrosion resistant materials and other details that result in a metallurgically efficient machine that has low repair and maintenance requirements. The mechanical and metallurgical design of magnetic separators at the Pilotac plant, Minnesota Ore Operations, United States Steel Corp. has progressed from the original single-stage, belt-type machines to the present multiple-stage, drum-type units, In ten years of operation, the plant operating and research personnel, in consultation with manufacturers, have made design changes to improve mechanical, electrical and magnetic features to meet process needs as flowsheet designs developed and to incorporate new permanent magnet materials as they became available. Separator specifications were an end result of this effort. The latest specifications which were developed for the Minnesota Ore Operations' plant were not all-inclusive listings; they covered only those points indicated by plant experience. For example, magnet pole piece design and dimensions were not stated. The manufacturers were given freedom to use any design as long as the field pattern was as specified. The selection of the items to be included in the specifications was undoubtedly influenced by particular conditions at Pilotac such as composition of plant water, concentration characteristics of the ore, repair and maintenance facilities available and the research programs that had been conducted. Only the developments leading to the specifications for a primary or "cobber" magnetic separator are presented in this paper. However, the same general concepts are used to specify secondary and tertiary separators. The areas of interest discussed include flowsheet service, tank configuration, magnet design, bearings, materials of construction, and some minor mechanical details. FLOWSHEET SERVICE The primary magnetic separators in the Pilotac Concentrator flowsheet are located after the first stage of grinding as shown in Fig. 1.

Jan 1, 1965

By R. H. Walpole, J. M. Kane

IN all probability the mining and metallurgical industry as a whole can demonstrate a larger ecorlomic return from installation of dust-control equipment than any other major industrial group. This fact has partially accounted for the marked increase of dust-control installations made during the past decade. While the primary objectives for installation of dust-collecting systems are improved working and operating conditions for men and equipment, the fact that an economic return can be anticipated on salvageable materials is an added advantage which shows in partial or complete equipment write-off. The conditions apply to most phases of the mining, milling, and smelting industry, both non-metallic and metallic. As with any mechanical devices, selection of suitable dust collector equipment involves evaluation of available products with characteristics most nearly meeting conditions of the application at hand. When there is valuable product to be collected, and/or when there are possibilities of air pollution or public nuisance, collector selection is often guided by the maxim of "highest available collection efficiency at reasonable cost and reasonable maintenance." A brief review of dust collector designs will permit outlining of major characteristics of each group. Final selection will involve detailed data against a background of the problem under consideration. The dry centrifugal collectors, see Fig. 1, represent a group of low cost units with minimum maintenance. They are subject to abrasion under heavy abrasive dust loads and to plugging with moist materials. Efficiency drops off rapidly on particle sizes below the 10 to 20 micron group. Because of the large amounts of —10 micron particles in most mining dust problems, they will normally be used as primary collectors and will be followed by high efficiency units. This combination is cspecially popular where the bulk of material is desired in a dry state with wet collection indicated for the final cleanup portion. In remote plant locations, dry centrifugal~ can be used alone if product in dust form has no value or if dust loading is light enough to eliminate a nuisance in the plant area. Where high efficiency dust colleotion equipment must be selected, choice will normally involve fabric arresters, wet collectors, or high voltage Electro-Static precip-itators. Fabric arresters, see Fig. 2, rely on the passing of dust-laden air at low velocity through filter fabric. Velocity ranges from 1 to 3 fpm for the usual installation and may be as high as 10 to 20 fpm in arrangements where automatic frequent vibration or continuous cleaning of the filter media is employed. Fabric is normally suspended in either stocking type or in an enlvelope shape. Collection efficiency is excellent even on sub-micron particle sizes. Equipment is bulky, must be vibrated to remove the collected dust load, and is restricted in applications from temperature and moisture standpoints. Condensation of moisture on the fabric filter mcdia causes plugging of the passages with great reduction in air flow. Temperatures for the usual medias of cotton or wool are 180" and 200°F maximum, although the introduction of synthetic materials such as nylon, orlon, and glass cloth have increased the possibilities of this type of collector for higher temperature applications. The wet-type collector may employ a number of different principles so that entering dust particles in the gas stream are wetted and removed. Principles usually include impingement on collector surface or water droplets, often in combination with centrifugal forces. Variety of wet collector designs is indicated by typical collectors illustrated in Figs. 3 and 4. Collection efficiency is a function of the particular design, although the better collectors will have high collection efficiency on particles in the 1-micron range. Wet collectors have the advantage of handling hot or moist gases, take up small space, and eliminate secondary dust problems during the disposal of the material. At times collection of the material wet is a disadvantage. Wet collectors may also be subject to corrosion and freezing factors. The high voltage Electro-Static precipitator, see Fig. 5, is probably the most expensive type of high efficiency collector. It finds its applications generally in problems in which collectors previously discussed cannot be employed. Its collection efficiency is based on its design features and can be excellent on the finest of fume particles. Material is normally collected dry. Gas temperatures are of no great concern as long as condensation does not occur within the dry type of precipitator and the temperatures do not exceed the limits for materials used in its construction. As with the fabric arrester, provisions

Jan 1, 1954

By C. W. Hoffman, W. R. Hinken

Probability sizing, a fairly recent development in the field of particle separation, is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages of probability sizing vs. conventional screening methods are: (1) reduced space requirements for a high capacity unit, (2) fewer moving parts, (3) more versatile product sizing selection, (4) reduced maintenance requirements, and (5) lower power consumption. Screening is a necessary part of virtually every crushing circuit. At some stage in the process, particle separation becomes a controlling factor in the operation. The basic type of screen in use today is the vibrating unit, which usually employs a mechanical vibrator of one type or another to obtain sizing and material transportation across the screen surface. The vibrating screen has its limitations and inherent problems. Operators must live with: (1) high maintenance — worn rods, screen cloth, spacers, cross members, chutes, etc., (2) low capacity in relation to floor space requirements, (3) extreme noise levels, (4) high power consumption, and (5) structural problems in the screens and supporting steelwork. All plant operators have become tolerant of these drawbacks through the years, and little innovation has been developed in screening. The vibrating screens in use today incorporate improved metals, more efficient power sources, better lubricants, and increased manufacturing skill, but the basic machine itself remains unchanged. Screening is a relatively small part of most plants' operating expenditures and gets relatively little attention from research and development. The HiProb sizer is a new approach to the problem of particle separation on a high tonnage basis. Developed by Dr. Fredrik Mogensen (president of Fred-rik Mogensen, A. B. of Djursholn, Sweden), this unit has found its primary acceptance in the sizing of wet or dry materials in the fine ranges. Climax has been working cooperatively with Mine and Smelter Supply Company, the United States licensee, on the adaptation of the sizer to obtain consistent recovery at a high tonnage rate on a — 3/8-in. separation. This was a new application for the sizer and opened up a whole new field of problems. Dr. Mogensen's machine utilizes the control of normal probability of falling particles and is designed to eliminate some of the undesirable features of vibrating screens mentioned earlier. The machine is light, compact, consumes less power than conventional screens and has a low noise level. PRINCIPLES Probability sizing is a process designed to allow solid particles to segregate with a high ratio of the materials reporting into their respective size fractions with a minimum amount of misplaced particles. Sizing is defined in this paper as segregation of dry solid particles into fractions of comparable sizes. Probability is usually estimated as the ratio of the number of ways an event might occur vs. the total number of allowable ways. The probability process described depends upon the fact that particles falling through a network will segregate across the sizing surface even though all openings are larger than the particles. The degree of segregation is dependent upon the particle size and the trajectory applied by the sizing network to each falling particle. Specifically, the process utilizes a maze made up of screen cloth to control the path of a particle in free fall as illustrated in Fig. 1. The usefulness of this probability sizing process is dependent upon the degree of efficiency of an effective maze. Primarily, a maze must be extremely flexible to meet the multi-faceted nature of solid particles and, at the same time, the degree of control must be reproducible so that a desired separation is predictable. Dr. Fredrik Mogensen has formulated a maze that is not only flexible and easily controlled, but, mote importantly, easily adaptable to a working machine.

Jan 1, 1970

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.' The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By K. E. Merklin, F. D. DeVaney

Students of the modern blast furnace seem unanimously agreed that they are observing a major revolution in practice. Rather than changing construction and operation of the furnaces, most of the great advances now under way deal with the raw materials feed. Prepared burdens have gained increasing significance during recent years. Sizing, concentration, and agglomeration have all become bywords to greater production and reduced operating costs. The remarkable results with test furnaces in which self-fluxing sinter makes up part or all of the ore charge foretell even greater improvements. Other investigators have reported many of these advances, and it is enough to predict here that more and more operators will turn to the use of self-fluxing sinter. This change in the operator's requirements comes at a time when one major section of the iron ore regions, the Mesabi, is finding it difficult to maintain, let alone improve, the tonnage and grade of its shipping product. To meet the new demands with respect to quality and structure, the iron ore producers of this area turned first to screening, crushing, and concentrating intermediate ores. More recently, declining higher-grade reserves have led to multimillion-dollar investments in plants to treat the low-grade magnetic taconites.1,2 To yield a suitable concentrate, the Minnesota magnetic taconites must be ground to about 80 pct through 325 mesh, too fine to be charged directly to the blast furnace or to make acceptable feed to the sinter strand. The pelletizing process was developed to meet the structure requirements laid down by the blast furnace operators. Taconite producers are succeeding in their efforts just when the attention of the blast furnace man is being drawn to the great advantages of self-fluxing sinter.3 The taconite operators are ready with an alternative. Why not produce sclf-flus ing pellets? At the Hibbing laboratory of Pickands Mather & Co., where much of the early work was done that led to Erie Mining's 7.5-million ton taconite plant at Hoyt Lakes, Minn., preliminary investigations have been made. Present Taconite Operations: Details of this work will be clarified by a brief review of agglomeration practice in commercial taconite plants. After the taconite has been ground to about 80 pct through 325 mesh to liberate the magnetite grains, the ore is concentrated on magnetic separators, thickened, and filtered to about 10 pct moisture. This structure and moisture fit in closely with the conditions required to produce good balls. It has been found with taconite concentrates that at least 60 pct of the feed to the balling drum must be —325 mesh to obtain good ball compaction within reasonable time. The filter cake moisture usually permits a slight water addition at the balling drum, and further balling control is obtained by adding about 12 Ib of bentonite and 1 1/2 lb of soda ash per dry short ton of concentrate. These additives, and occasionally small quantities of fine coal, are thoroughly mixed with the filter cake ahead of balling. The swelling property of bentonite improves the green and dry strength of the balls so they can be handled without breakage until they are fired. Soda ash is added for pH control to insure maximum performance of the bentonite, and coal is added for more heat in the firing process when required. The balls, normally 3/8 to l-in. diam, are brought to a temperature of 2350" to 2500°F in the indurating furnace. Heat for this process comes from three sources: 1) fuel burned in the combustion chamber, 2) oxidation of the magnetite concentrates to hematite, and 3) coal added to the balls. Pellet strength is developed by grain growth and bridging and, if enough slag-forming constituents are present, by slag bonding. Conversion to hematite is usually close to 100 pct in the fired pellets. Batch Test Procedures: Initial studies of self-fluxing pellets were made by producing balls on a batch basis under carefully controlled laboratory conditions. The l-in. balls, uniform in size, were fired in an oxidizing atmosphere in a standard laboratory muffle furnace. The firing procedure consisted of

Jan 1, 1961

By D. F. Kaufman, H. R. Spedden, A. M. Gaudin

MANY studies of comminution have been made to ascertain the size distribution of the product and to evaluate the work of comminution in the light of the size distributions of the feed and product. Up to now, these studies have been essentially statistical in character, that is, a certain lot of feed was subjected to comminution in some specified way, and the aggregate product was fractionated into sizes, thereby losing all knowledge of individual relationship of feed to product pieces. Radioactive tracers offer a means to do something in this respect which could not be done before, namely, to follow the rupturing of some particular piece in its normal environment of other pieces. That is, it permits going beyond the usual statistical limitations of size distribution studies to what may be termed a personalized or individualized study. The purpose of this paper is to present some preliminary experiments conducted with this tool. The method employed was to mark radioactively some constituent of a feed. It is possible, of course, to consider the preparation of two lots of material of which one is radioactive and the other is not, and to blend the two ahead of the comminuting step; but to do so is open to the objection that the two preparations may not be identical. Therefore a technique has been chosen that removes this objection by merely taking out a size fraction of a comminution feed, rendering that fraction radioactive by exposure to a neutron flux, and then by returning it to Table I. Size Distribution of Offspring Albite Particles Originally 28/35 Mesh and in Admixture with Other Sizes After Grinding 2 min in a Steel Ball Mill Specific Activity ' Cumu- Corrected Distrl- latlve Size for Back- butlon In Distri- Fractlon ground, Weight, Product, button, of Product, cpm/gm g Pctb Pct Mesh (A). (W) (P) (ZP) + 28 0 56.0 0 100.1 28/35 62.6 54.0 24.8 75.3 35/48 62.8 59.4 27.7 47.6 48/65 41.1 53.0 16.2 31.4 65/100 29.6 45.7 10.2 21.2 100/150 23.7 37.0 6.6 14.6 150/200 23.3 25.1 4.4 10.2 200/270 20.1 19.0 2.9 7.3 270/400 17.8 21.2 2.9 4.4 -400 22.9 25.2 4.4 — 100.1 a These activity determinations were made in rapid succession in the order given. The specific activity (Ao) of the active 28/35 mesh fraction of the feed was measured at the beginning, after the measurement on the 65/100 mesh size fraction of the product, and; The end. The decay-corrected activities at those times were 246.7, 241.0. and 236.9 cpm per gm. The weight (W0) of the active 28/35 mesh fraction in the feed was 55.0. b Example of calculation for P in the 65/100 mesh oroduct frac- A W tion; A = 29.6, W = 45.7, Ao = 242.7, Wo = 55.0: P = — x — Ao Wo = 0.102 = 10.2 pet. the remainder of the charge for the comminution experiment. A relatively simple procedure was developed by which albite, containing sodium, was activated in the M.I.T. cyclotron. The cyclotron makes highspeed deuterons which impinge on a beryllium target, thereby producing a concentrated neutron flux. The mineral was exposed to this flux for 2 hr. This treatment changed enough of the sodium to sodium 24 (14.8 hr half-life, 1.4 mev ß) as to make detection and measurement easy. The nuclear reactions taking place were: 11Na23 (n,?) 11Na24 (irradiation) 11Na24 ß,?,? 12Mg24 (decay) The detailed technique of the experimentation was as follows: 40 kg of hand-sorted, lump albite were crushed to pass 10 mesh. After careful mixing of the lot, a screen analysis was made. The whole lot of material was fractionated on standard Tyler screens from 14 down to 200 mesh. Samples for experiments were compounded from these fractions in accordance with the screen analysis. When it was desired to make an experiment in which, for example, the 28/35 mesh size fraction was to be studied, the blend of size fractions was made as indicated above, except that the 28/35 mesh size fraction was added only after irradiation in the cyclotron. The blended charge containing the activated albite was ground for 2 min in a laboratory ball mill with a steel ball charge of controlled size distribution. The ground product was carefully sized on a set of Tyler screens in a Ro-tap. Each size was analyzed for radioactivity by the use of an end-window Geiger-Mueller counter and standard scaling circuit. This analysis was carried out in detail as follows: a 20-g sample was placed in a Petri dish, packed carefully to obtain reproducible geometric distribution with reference to the Geiger-Mueller tube, and the activity was counted for a 2-min period. Several determinations of the activity of the active size fraction in the feed were made at various times to establish the decay in activity with time. Linear interpolation was used to evaluate the activity that the active size fraction in the feed would have had at any given instant. The ratio of the observed activity in a size fraction of the product to the activity that the active size fraction in the feed would have had at the same time gives the fraction in the product size that came from the irradiated size in the feed. The general formula for finding the distribution, P, of a specific individual size fraction in the feed

Jan 1, 1952

By F. M. Lewis, J. F. Myers

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By F. M. Lewis, J. F. Myers

W. I. Garms-—The authors state that when they added 11 tons of balls to the 45 pct volume ball load, the power needle did not budge. The question arises as to whether any increase in capacity accompanied the 11-ton addition. It is hardly conceivable that all of the balls making up the 11-ton addition were sterile. However, as the work done in the ball mill is not by kilo-watthours per se or balls per se but by kilowatthour-balls, it is possible that the kilowatthourballs in the mill before the 11-ton addition had a different amperage, voltage or robustage than those in the mill after the addition and that the overall outcome was that equal work was done before and after the addition. The authors can keep the efficiency that they got with the 45 pct volume 1-in. ball charge and get additional capacity by putting more kilowatthourballs to work in the form of the addition of 11 tons of 2-in. balls to the present ball charge, and subsequent makeup additions by weight of 20 pct 2-in. balls and 80 pct 1-in. balls. J. F. Myers (authors' reply)-—Mr. Garms points his finger at the 11 tons of "sterile" balls added to the Tri-cone mill. A fact so interesting to us that we felt it should be reported. Clearly, ball slippage at the existing mill speed prevented any further transfer of power from the shell to the ball mass. We agree that the kilowatthourballs would increase, were we charging rough 2-in. balls as suggested by Mr. Garms. The assumption is, of course, that we would get a corresponding increase in work done. Our reported data (CIME meeting, Vancouver, 1946) shows a gain of work accomplished of 7.6 pct as we decreased the ball size from 2 in. to 11/2 in. and a further gain of work accomplished of 2.1 pct when we went from 11/2 in. to 1 in. The small ball results reported by H. R. Banks at Chapman Camp are also very convincing. In the case of 2-in. balls they would take the conventional ball path and start cascading. They would thus destroy the classifying pool over the "foot" of the

Jan 1, 1951