Search Documents

By Samuel W. Woods

The Tacoma, Washington plant is one of six plants in the United States Gypsum Company's Acoustical and Mineral Fiber Division. The Tacoma facility was acquired in 1959 along with six other mineral wool plants from the American Rock Wool Company. Originally, the Tacoma plant was built as a carbide plant during the Second World War and after that was converted and operated as a mineral wool plant by several insulation companies. Through these early years, the use of raw materials at Tacoma consisted primarily of slags along with small percentages and various combinations of silica (in various forms such as gravel), limestone and basalt. These raw materials were melted in cupolas using coke as the heat source. Raw material usage and types as well as mineral wool production methods and equipment remained without major changes for many years.

Jan 1, 1983

By William F. Lawrence

Research performed by the West Virginia University Coal Research Bureau under the sponsorship of the U. S. Bureau of Mines has demonstrated that coal-ash can be converted into mineral wool insulation of a quality equal to commercial grade mineral wool. An unexpected benefit has been gained due to the discovery that the usual and costly fluxing agents employed when using conventional raw materials are not required when producing mineral wool from coal-ash. Because coal-ash sources are commonly located close to mineral wool marketing areas and because mineral wool is seldom shipped far as a result of its low weight and high volume, the use of coal-ash may offer the mineral wool producing industry profitable opportunities. Moreover, coal-ash produced from experimental limestone based air pollution control processes also yields high quality mineral wool which may aid in retarding corrosion of metals contacted by the wool. In addition, internal fluxing effects and possible sulfur oxide utilization could provide economic advantages to the use of these "modified" ashes.

Jan 1, 1969

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970

By Kenneth M. Ritchie

Mineral wool is a term applied to man-made fibers of silicate glass with useful properties resulting from their fibrous nature. In contrast with crystalline fibrous minerals such as asbestos, mineral wool fibers are amorphous, solid filaments produced by drawing from molten liquid and subsequent cooling. Chemically they are silicate glass with varying percentages of metallic oxides, especially those of aluminum, calcium, magnesium, iron, and in glass wool, sodium, potassium and boron. Other elements such as manganese, titanium, sulfur, etc., result from their presence in the raw materials used and are not purposely added. In the United States, mineral wool is a generic term and may be applied to rock, slag or glass wool. In Europe, glass silk and silicate cotton are products in the same category, but the term mineral wool is less commonly used. Current usage is to ignore the actual source and to differentiate products on a composition basis; thus rock and slag wools have about 35-45 pct of silica, while glass wool has 54 to 60 pct. Much mineral wool of slag origin is called "rock wool," and this practice is increasing, although wool made of slag from lead or copper refining is often referred to as "lead slag wool." Its greenish-gray to greenish-black dark color, due to 5-25 pct Fe (reported as FeO), distinguishes it from "white" wools made from iron, blast furnace slag containing only 1-2 pct FeO or Fe203. Most mineral wool is used for thermal insulation against heat and cold; sound absorption and isolation are probably the next most important uses. Both its thermal and acoustic values result primarily from the physical structure of the heterogeneous mixture of fibers and air which is the form in which the fibers are first obtained and handled. For this reason, within fairly wide limits, differences in chemical composition are relatively unimportant, and for most conventional applications all types are competitive in properties and value. Mineral wool intended for extreme conditions of high temperature, acid resistance and special purposes must have a chemical composition which will insure the desired properties. This may differ greatly from that of ordinary wools; for example one product approximately 98 pct Si02 and another consisting of 50 pct A1203 and 50 pct Si02 are produced and sold for high temperature service up to 2000°F or more. These are considerably more expensive to manufacture and their cost limits their use. Historical The manufacture of mineral wool consists fundamentally of a process which subjects molten material to shear and/or tensile forces that draw them into fibers. The liquids are cooled at a rate which solidifies them quickly. As a solid glass they are technically super-cooled liquids since they have no true melting point. The drawing out of glass into thin rods, filaments and tubes was known from very early times, and present day continuous production of glass filament for textiles was evolved gradually by adapting hand methods to automatic machinery. Rock and slag wool manufacture had a somewhat different development. Early explorers reported finding filamentous material

Jan 1, 1960

By J. E. Castle

THE title of this article is descriptive, but not complete, for psychological evaluation is almost as important as rigid economic evaluation. This refers to those human traits that cause people to be too optimistic about the projects they are sponsoring, to overlook obvious weaknesses, to base decisions on incomplete and inaccurate data, and to gloss over embarrassing problems. Investment of capital in a new industrial mineral project is warranted only after rigorous economic analyses based on unquestionable facts. A plunge into production cannot be justified solely because these minerals have been deposited in the ground and are therefore free. There are no specially favorable economic laws that make the business of industrial minerals more attractive than any other. The factors of supply and demand, marketing, technological changes, taxes, competition, and fluctuating prices apply as much to industrial minerals as to other business enterprises. What is more, industrial minerals are subject to the higher risks that all mining enterprises face.

Jan 6, 1958

By G W. Scott, R C. Johnson

Hypogene alteration zones have been described as a precursor to high-grade haematite deposits in Australia, Brazil and elsewhere. This alteration is described as being below or distal and is typically magnetite-carbonate-silicates reflecting Mg - Fe metasomatism. This paper describes, without genetic implication, the mineral zonation and possible structural control on mineralogic variation within the Tilden Mine, a concentrating grade haematite deposit in Michigan, USA. In contrast to the high-grade deposits, these variations are not peripheral to the orebodies but are the ore. The deposit occurs within the Negaunee Iron Formation, along the southern margin of the Paleoproterozoic Marquette Range Supergroup basin. The regional structure is a fault-bounded west plunging syncline within the crustal scale Great Lakes Tectonic Zone, which forms the boundary between Archean granite-greenstone and gneissic terranes. Local structure consists of second-order anticlines and synclines with variable northwest and southwest plunges. The interaction of sedimentation and diagenesis within growth fault controlled basins, along with a possible metamorphic and/or hydrothermal overprint has resulted in a complex series of ore types. For modelling purposes, the deposit is divided into geologic domains based on both lithology and metallurgical response in the laboratory and in the plant. Mineralogic variation is recognised within individual mineral grains; at blast pattern (10 - 15 m) and development drill hole (100 m) scales.

Jan 1, 2007

By Will H. Coghill

The scope of this paper is such that it was deemed advisable to group the contents into several main sections. They are: Section 1. Geography and Geology. Section II. Historical Review. (a) Mining and Smelting in Alabama. (b) Milling. (c) Summary of Milling Research. These two sections are primarily a bibliography and summary of the research on the Birmingham Red Mountain ores up to the middle 1040's. Section III. Status of the Birmingham Iron Industry. This sect ion points out the extent to which the findings of the iron-ore research have been applied on a commercial scale. Also, a very brief description of the dependent and allied industries is included. The value of the Birmingham iron ore is greatly enhanced by the proximity of coal and dolomite. Thus the coal and coke industry and the dolomite industry are closely allied with and to a large extent dependent upon the possibilities of economic utilization of the Red Mountain iron ores. Section IV. Beneficiation Investigations of the Red Mountain Iron Ores. This is a record of the most recent, hitherto unpublished work of the Southern Experiment Station of the Federal Bureau of Mines, Tuscaloosa, Ala., on the chemical and physical composition not only of the Big seam but of most of the iron-bearing rock strata of Red Mountain.

Jan 1, 1946

By Max W. Ball

THE geologist or mining engineer, whose work takes him into the western United States, whether for the Government or private enterprises, is likely to be called upon to classify public lands as to their mineral character, or to review such classification already made, usually by a Government geologist or mineral inspector. The public-land law covering the matter is clear and logical, and a knowledge of its simpler principles is necessary to intelligent classification work. There are two classes of cases in which a classification of lands as mineral or non-mineral may be required: .first, cases in which lands classified as mineral will be retained by the Government and lands classified as non-mineral alienated; second, cases in which lands classified as mineral will be alienated and lands classified as non-mineral retained.

Jan 1, 1921

By Waldemar W. Koczkodaj, William O. MacKasey

Abstract - A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simplified case of volcanic-associated massive sulfide type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of nonmeasurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to refine at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By Waldemar W. Koczkodaj, William O. MacKasey

A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simpli?ed case of volcanic-associated massive sul?de type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of non-measurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to re?ne at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By J. A. Herbst

During the last decade it has been established that conventional mineral-processing control strategies based on classical control theory result in significant increases in plant throughput and operating-cost savings. It has, however, also been recognized that conventional strategies have important limitations for complex multivariable mineral-processing systems. These limitations center around the fact that single-input/single- output control linkings often result in highly undesirable interactions between controllers. During the last few years new and promising approaches to solving this problem have emerged. These approaches are based on the use of on-line dynamic models to make predictions which are useful for control decision-making. This paper presents a brief summary of the state-of-the-art for mineral-processing control in 1984. This summary is followed by a review of recent developments in model-based control strategies including those in optimal control, self- tuning regulators and decoupling control. Expected trends for the future in the control of mineral-processing operations are discussed.

Jan 1, 1984

By Miguel Rivera F.

El presente texto señala el origen de las menas del yacimiento de la Quebrada de Tuco (Ancash), las cuales se relacionan con las exploraciones como en la evaluación de un yacimiento ubicado. Este yacimiento mineral está formado por unos mantos y vetas de sulfuros, con valores de plata magnesio, zinc, plomo y cobre, acerca del cual se han pronunciado algunos geólogos con opiniones diversas. Para ello, se realizó una investigación mineralógica a nivel microscópico, que se relaciona con la información que evidencia sobre el origen del yacimiento y su relación con diversos fenómenos geológicos.

Sep 1, 1985

By Edward Bullard

El presente texto señala los problemas tecnológicos, económicos y políticos que plantea la explotación de minerales de los fondos marinos. En ese sentido, las investigaciones internacionales realizadas sobre el Mar Rojo durante la última década y el proyecto JOJDES en el Atlántico proporcionan un conocimiento completo de las posibilidades del beneficio de los minerales.

Mar 1, 1975

By M. Iberico

A partir de los años 70 se incrementó el proceso de exploración y desarrollo de los yacimientos mineros submarinos. En este sentido, el presente trabajo describe el origen de los depósitos a partir de los descubrimientos de módulos manganíferos en el océano pacífico que hicieron Thompson y Murray. Posteriormente Buchanam demuestra la existencia de módulos ferro-manganíferos en aguas poco profundas ( 200 m. ), de composición diferente de las provenientes de aguas profundas. De otro lado, el trabajo señala también la división de los minerales marinos en tres categorías: las sales disueltas y en organismos, los sedimentos y depósitos en el suelo profundo submarino y los depósitos consolidados e inconsolidados de la plataforma continental. Por último, se describe los procesos de beneficio y las ventajas de la explotación de los recursos submarinos en el futuro de la minería submarina.

Nov 20, 1972

The El Pe±on gold-silver deposit comprises four epithermal, low-sulfidation veins, which contain 2.9 million oz Au and 48 million oz Ag. Provisional data on alteration mineralogy, fluid inclusions, and vein textures constrain the chemistry and hydrology of the hydrothermal system responsible for ore mineralisation at El Pe±on. Alteration minerals include quartz, adularia, albite, illite, smectite, calcite, chlorite, and pyrite. Alteration minerals suggest the existence of near neutral pH, low salinity hydrothermal fluids, which circulated over an area greater than 18 km2. Complex mineral zonation patterns result from variations in host rock permeability and composition, overprinting alteration possibly produced by thermal waters from surficial and peripheral parts of the hydrothermal system, and supergene weathering in the hyperarid environment. Upflow zones were focused along N-S and NE trending structures, producing crustiform quartz-adularia+carbonate veins. Fluid inclusion data indicate vein deposition from low salinity (

Jan 1, 2002

By S Meffre, S Golding, K Zaw, J McPhie, R James, S Suphananthi

The Chatree deposit is located in the central portion of Loei Fold Belt, which extends from Lao PDR in the north through centralThailand to Cambodia in the south. Epithermal gold-silver mineralisation at Chatree occurs as veins/veinlets and stockworks with minor breccia in volcaniclastic and volcano-sedimentary rocks of andesitic to basaltic andesite composition and Permo-Triassic age. This preliminary oxygen isotope study mainly focuses on vein quartz of Au-Ag bearing mineralization (Stage 2) and a few samples of late Stage 4 quartz ¦ calcite veins. Quartz from Au-Ag bearing mineralisation has oxygen isotope values ranging from 8.1 to 12.3ë with the lowest values generally occurring at the deeper level (140 m below the surface). The late barren quartz ¦ calcite veins (Stage 4) tend to have higher oxygen isotope values ranging from 11.9 to 12.0ë. The oxygen isotope composition of the Chatree ore fluids were calculated at 250¦C, 300¦C and 350¦C based on homogenisation temperatures of fluid inclusions. The calculated oxygen isotopic composition of the Chatree ore fluid ranges between -1 and 6ë that overlaps with both meteoric and magmatic compositions. This shift in oxygen isotope compositions may relate to processes such as water rock-interaction and/or mixing of meteoric and magmatic fluids. It is interesting to note that the lowest quartz oxygen isotope values are spatially more or less confined to the prominent structures in the centre of the major ore zones. These structures may have been acted as conduits for higher temperature magmatic fluids. The quartz oxygen isotope values increase outwards from the centre of the main ore zones to the margin of the pits possibly due to mixing of magmatic fluids with lower temperature meteoric water. Whole rock oxygen and hydrogen isotope studies are in progress to investigate isotopic trends in the wall rock away from the ore zone. The systematic variation of oxygen isotopes in quartz from the mineralised veins and adjacent wall rocks could potentially be used as a vector to ore. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By D Craw, L Cox, R J. Norris

The Rise and Shine Shear Zone is a mineralised low-angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. The zone is commonly believed to be similar to the actively mined Macraes deposit. The Rise and Shine Shear Zone occurs in the immediate footwall of the Thomsons Gorge Fault, a regional scale Cretaceous normal fault that juxtaposes chlorite zone schist against biotite zone schist. Most mineralised rocks are deformed and record a progression from early stages of semiductile deformation to more brittle cataclasis. Folds in mineralised rocks trend northwards. The mineralised schist is hydrothermally altered with variable silicification, sericitisation, chloritisation, replacement of titanite by rutile and carbonate alteration. Gold is associated with pyrite and arsenopyrite and occurs in both ductile and brittle microstructures. Sheared and mineralised schist is cut by north-striking fault zones which host mineralised quartz veins. Veins in the shear zone contain hydrothermal albite. Trace element analyses show enrichment in As, U, Th and rare earth elements. Many of the above features are similar to Macraes deposit, but there are important differences. In particular, the Macraes deposit is hosted in lower grade rocks and truncated beneath by a normal fault, Macraes has no U or Th enrichment, Macraes veins have no albite and folds at Macraes trend NW-W. Rise and Shine mineralised rocks have no Cr enrichment and no hydrothermal graphite.

Jan 1, 2005

By Ian J. Graham, Cornel E. J. de Ronde

New Zealand lies astride a convergent plate boundary that extends north-eastwards from the Taupo Volcanic Zone (TVZ) to Tonga. This boundary is marked by the Kermadec arc, c. 1200 km of which falls within New Zealand’s EEZ, and which is host to numerous volcanic edifices both on the arc and in a zone immediately behind the arc to the west. In 1999, thirteen volcanic centres in the southern 260 km of the arc were surveyed for their hydrothermal plumes with seven of them discharging vent fluids into the surrounding ocean. Three of the seven volcanic centres have had mineralised rocks recovered from them during dredging and submersible operations, namely Brothers, Rumble II West and Clark. Presentday plume data combined with mineralogical evidence indicate that the vent sites at Rumble II West and Clark are waning, although the presence of Cu-rich sulphides in samples recovered from Rumble II West suggest there may be a massive sulphide (Cu-Zn-Pb-Ba ± Au) deposit located within the caldera. Brothers volcanic centre is host to the largest polymetallic mineral deposit discovered along the Kermadec arc and has numerous, up to 7 m tall chimneys within a c. 600 x 200 m area located on its NW caldera wall. Geochemical data indicate that concentrations of base metals are variable and depend critically on sample type. When combined with mineralogical and plume data, this indicates addition of a magmatic fluid component to the vent fluids.

Aug 24, 2006

The Hunter Fracture Zone can be traced into the Fiji group, and onshore SE Viti Levu in the form of NE-trending morphostructures. NW- trending morphostructures offset the NE elements. Structural mapping of Suva Harbour indicates that the NE elements are grabens bordered by faulted monoclines. Faulting is characterised by block-rotations and dip-slip displacements. The NW morphostructures are faults displaying elements of both dip-slip and strike-slip movement. Structural overprinting suggests that the NW faults represent the youngest phase of deformation, and current seismic activity occurs on this trend. A conceptual, geomechanical model of the deformation invokes toppling and wedge failure at the edge of the Fiji platform, translating material downslope into the Hunter Fracture Zone. The interference pattern produced by the superposition of the NW on the NE structures consists of a series of circular features bearing superficial resemblance to volcanic centres. Known mineral deposits in SE Viti Levu correspond closely to these features. The formation of the circular features postdates mineral genesis, suggesting that the features provide a focus for the enhanced exposure of mineral deposits rather than a source of mineralisation. There is a close association between mineralised exposures and interference patterns in extensional structures in SE Viti Levu, and a correlation between these structures onshore, and the Hunter Fracture Zone cum South New Hebrides Trench offshore. Future mineral exploration in the SW Pacific will benefit by closer consideration of the geologic structure of Pacific islands bordering the extensional regimes of deep oceanic trenches.

Jan 1, 1987

By B A. Mowat, T M. Leach

The Morobe Goldfield inPapua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23 t) and Edie Creek (4 t) and geological resources have been established at Hidden Valley (78 t), Kerimenge (36 t) and Hamata (30 t).Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.   It is proposed that magmatic fluids which evolved from parent melts to the high level Edie porphyry stocks mixed with convecting meteoric fluids and were channelled along major structure and diatreme contacts. Proximal to the intrusives, gold mineralisation is associated with deposition of pyrite-hematite-quartz+/-magnetite-gold (Hamata) and pyritebasemetals-quartz-gold (Wau). The mineralising fluids were hot, and periodically saline due to pulses of magmatic fluid. Gold is non-refractory and occurs as 20 to 30 micron blebs within the pyrite.   More distal from the intrusives or under late cooler conditions, mixing of cool dilute meteoric and magmatic fluids resulted in gold deposition associated with arsenic rich pyrite-and arsenopyrite-mineralisation (Kerimenge, Hamata and Edie Creek). Gold is refractory and occurs within the sulfides either as sub-micron inclusion or within the lattice.   CO2 and H2S gases which evolved off the upwelling hydrothermal fluids as a result of boiling and pressure reductions, condensed within superficial groundwater and formed cool oxygenated bicarbonate fluids. These fluids percolated back down the structures depositing manganocarbonate in the upper parts of the hydrothermal system. At deeper levels in the system mixing of the descending bicarbonate fluid with upwelling mineralised fluids deposited manganocarbonate-quartz-sulfides nonrefractory gold (Hidden Valley, Wau and Edie Creek).   At Kerimenge the cool bicarbonate fluids have also quenched a late stage magmatic fluid rising along high permeability structures. The quenching has resulted in deposition of non-refractory gold mineralisation associated with hessite (Ag2Te)-tennantite-chalcopyrite deposition.   Within the Morobe Goldfield, a transition from deeper level pyrite-quartz+/-hematite-magnetite to intermediate level quartz sulfide and quartz-carbonate-sulfide deposition to upper level, massive manganocarbonate deposition is recognized. Gold mineralisation can occur within all levels up the system.

Jan 1, 1995