Search Documents

By Owen Matthews

THE property of Cochenour Willans Gold Mines, Limited, is in Dome township, Red Lake area, northwestern Ontario, a hundred miles north of Kenora and close to the Manitoba border. 'Planes of Canadian Pacific Air Lines, Limited, serve the district daily, except Sundays, from Kenora, Ontario, and Lac du Bonnet, Manitoba, passengers being trans-ported from Winnipeg to Lac du Bonnet by car. Freight is handled by the Patricia Transportation Company. It is brought in from Hudson, Ontario, on the Canadian National railway, in summer by water and in winter by tractor trains over the frozen lakes. The first staking on the property was done during the 'rush' of 1926 and 1927 by William M. Cochenour, and on April 30th, 1928, a syndicate was formed, taking in claims of W. M. Cochenour and Dan Willans and H. G. Young. Surface trenching was carried on almost continuously until 1934. In October, 1932, Ventures Limited took an option on the property, and in December of that year they carried out an extensive diamond drilling programme, but considering the results did not justify further work, they relinquished the option. In July, 1934, further surface work was carried out under the supervision of W. P. Mackle and, on the strength of his report, Noah Timmins Incorporated took an option on the property and agreed to make an initial expenditure of $100,000 on development work. This was carried out under the direction of Hollinger Consolidated Gold Mines and included the sinking of a shaft to a depth of 165 feet, establishment of a level at the 150-foot horizon, and some 1,900 lineal feet of drifting and cross-cutting. The results obtained from this work were not considered of sufficient promise and the option was terminated in August, 1935. Mr. Cochenour then approached Alex Mackenzie and associates, and the present Company, Cochenour Willans Gold Mines, Limited, was organized on April 9th, 1936, and sufficient money was raised to continue operations. Under the direction of W. P. Mackle, the shaft was deepened and a second level was established at the 275-foot horizon; but, due to several adverse reports by outside engineers, it was found impossible to raise sufficient money to carry on the work and operations were suspended in December, 1937. In January, 1939, an agreement was entered into with Gold Eagle Gold Mines for the milling in their plant of some Cochenour ore. A total of 4,959 tons was treated, and the results were so encouraging that further finances were raised by C. A. Gentles & Company, of Toronto. Following further development in the mine, it was decided to erect a mill. Construction was started on September 1st and the mill was turned over on November 29th. The first gold brick was poured on December 23rd.

Jan 1, 1942

IN presenting a'description of milling and treatment methods at the Waihi mine, it is advisable to first traverse a good deal of the past history of the mine, and show the various steps which have led up to present-day practice. The record of the company is one of steady, solid advancement, both in metallurgical and financial results. This is illustrated by the following figures, dating back from 1897...

Jan 1, 1912

By K. Mikulash

"Agnico-Eagle Mines Limited is located at Joutel in North-Western Québec. The mine is about four miles north-west from the town on the left bank of the Harricana River. The present mining is 1,800 feet deep with an extensive geological development below this level.HISTORY The development of the ore body started sometimes in 1967 and then the operation ceased in 1969 and again reopened in 1973 due to higher prices of gold. During these periods of active development, a considerable metallurgical research has been done by different laboratories and research and design companies.The original capacities of the Mill differed as much as 30%. So did the concept of the ore treatment. The original design of the mill was for 200 TPD of ore with straight cyanidation. The problems with low gold extraction, high reagent consumption and poor filtration resulted in a decrease of the expected mill output to an initial 550 TPD with gold recoveries in the order of 40 to 60%.Although the studies and research work done on the ore varied, all of them had a common conclusion: a very fine grind is needed to expose gold. The mining method (sub-level blast hole mining) now provides the ore that differs from that on which the metallurgical test work was conducted and the original capacity calculations had been done.These variations in the concept consequently led to the conclusion that the size of gold is a determining factor for the process.Kilborn Engineering provided the original design with the Leslie Eng¬ineering completing the design. The metallurgical test work has been done by the Department of Energy, Mines & Resources, Lakefield Research of Canada, Kilborn Engineering and Sidam Incorporated.The new flotation section with secondary grinding has been designed and put into operation by the company in December 1975 with the results yet to be evaluated."

Jan 1, 1976

By Howard G. L

The gold treatment plant of Great Western Consolidated N.L. is at Bullfinch, Western Australia, 22 miles north of Southern Cross, which is 100 miles west of Kalgoorlie. A railway to Southern Cross connects the mine with the main Perth-Kalgoorlie line.The plant, which commenced operations on the 31st October, 1952, was, designed by Messrs. Alex: Stewart & Co. in consultation with the technical staff of Western Mining Corporation Ltd. to treat 1,000 long tons a day, made up of approximately equal parts of quarry oxidized ore and underground sulphide ore, by moderately coarse grinding (2-3 per cent plus 65 mesh Tyler) and straight cyanidation without straking. The design had to allow for future treatment of all sulphide ore at the rate of 40,000 tons per 28-day periodand to make provision for the possible later inclusion of preaeration treatment.The test work on .which design was based was done on representative development samples, the mine being divided into zones for this purpose, to check possible local variations from average treatment behaviour. Proposed mill feed mixtures were made up from time to time for complete ore dressing tests, which were conducted in the Western Mining Corporation laboratory at Kalgoorlie.The chief feature of the design was that the plant had to handle the extremes of very soft, poor settling and filtering oxidized ore and very hard, good settling and filtering sulphide ore. On one hand, crushers and mills had to be large enough to handle the sulphide ore and on the other, thickeners and filters had to be large enough to handle the oxidized ores.The design is marked by simplicity, the use of large units of equipment, and flexibility to cope with a variety of ores.

Jan 1, 1956

By Ed Ramsay

The Hill is a cyanidation plant with flotation and roasting. The grinding and treatment have at the present time a capacity of 1400 tons of ore per day and the precipitation has a capacity of 6000 tons per day. The ore is delivered by a 36" conveyor belt and tripper to 8 mill bins having a capacity of 6000 tons. The ore from these bins is discharged onto 20" gathering conveyor belts which are regulated with p.i.v. speed changers to control the belt weight. A weightometer determines the tonnage milled. The feed enters the 8' x 12' rod mill through a rubber lined chute and the product is discharged through a launder to a 7' rake classifier in closed circuit with 10' by 6' hardinge ball mill. Lime slurry is added at the rake classifier to give a strength of .30#/ton. The classifier sand is fed into the ball mill with a scoop feeder and the mill discharge flows in a launder back to the classifier. The classifier overflow is pumped to a 24' by 12' bowl classifier in closed circuit with a 8' by 15' regrind mill. The bowl classifier sands are fed to this mill and the mill discharge is pumped back to the bowl. The bowl overflow at 8% - 200 mesh is the final product from the grinding circuit.

Jan 1, 1975

By Ed Ramsay

The Kerr Addison process involves the cyanidation, flotation, and roasting of graphitic gold ore. The grinding and treatment section of the present mill has at the present time a capacity of 1400 stpd and the precipitation section has a capacity of 6000 stpd. The grind is maintained at 80%, -200 mesh, and a gold recovery of 92% is obtained in the cyanidation circuit. With flotation and roasting, the overall gold recovery is increased to 98%.

Jan 1, 1978

An account of milling "methods and costs at Mount Isa Mines Limited up to the year 1938 has been published. The present paper outlines the methods since adopted in the milling of lead-zinc ores and presents a description of the equipment now being provided for the milling of copper ore.The programme approved for the mining, milling and smelting of both lead-zinc and copper ores involves the milling 9f 50,000 tons of lead-:-zinc ore and 35,000 tons of copper ore per month.The crushed ores will be delivered to the surface from alternate levels through No. 2 Ore shaft and conveyed to their respective crude ore bins at the crushing plant. The ores will be crushed and milled in separate circuits in common buildings and the tailings will be stored on a common tailings dump. The water services to the two circuits will be separate.LEAD ZINC PLANTCrushing PlantThe crushing plant described in the previous paper was located adjacent to the Urquhart shaft. The crushing plant had grown considerably over the years by the addition of a 4ft. BY-mons shorthead crusher and a set of Traylor 72 in. x 20 in. crushing rolls and, whilst operating satisfactorily, was difficult to maintain and cramped in many places. As a satisfactory layout for the new copper crushing plant could not be made in the vicinity of the, existing plant, it was decided to construct a new plant on the western side of theconcentrator building and provide identical equipment in...

Jan 1, 1953

By Harry J. Cain

Introduction The property of Pioneer Gold Mines of B. C., Limited, is located in the Lillooet mining district of British Columbia, on Cadwallader creek, 54 miles distant by motor road from Shalalth, a station on the Pacific Great Eastern railway. Milling by the present Company was commenced in 1924, a small amalgamation plant, consisting of a crusher, Bryan mill, and plates being operated until 1928. Tailing from this plant was impounded and later treated in the 100-ton continuous counter-current decantation cyanide plant which was erected during 1927-28 and placed in operation during May of 1928. A second cyanide plant, employing continuous counter-current decantation, having a nominal capacity of 200 tons, has been erected during the past few months and was put into operation during September of the present year. The ultimate capacity of the combined units of the present mill has not been determined, but it is expected to be much in excess of the rated capacity. The Ore The ore, as received at the mill, consists chiefly of quartz carrying free gold, with small amounts of pyrite, arsenopyrite, and pyrrhotite in evidence, though probably amounting to less than one per cent of the total. Some gold is very closely associated with the sulphides. The country rock is a basic igneous rock, probably an augite diorite. Near the vein it is highly altered to sericite, which slimes readily on grinding, and does not settle very well. The quartz is of two types, clear and ribbon. In the latter, the ribbons, which are not much thicker than paper, consist of shattered sulphides. In crushing this ribbon quartz, breakage is often along the streaks, exposing these shattered faces to advantage in subsequent treatment. While gold is the metal for which the ore is mined, some silver is also present and is paid for by the mint. It is, however, unimportant from a commercial viewpoint. From the standpoint of crushing and grinding, the ore might be termed 'medium 'hard'.

Jan 1, 1932

By HENRY JULLUM

THE ARGONAUT' mill stands at the crest and spreads down the western slope' of a hill, which incidentally covers the' outcrop of the Argonaut vein' at this point. The collar of the main shaft of the mine is situated on the eastern slope of the same hill 120 ft. below the highest ?point. The present mill, built in 1916, was designed to treat 250 tons per 24-hr. day. This capacity has not been attained recently owing to the inability of the mine to produce enough ore while extensive development and underground construction were under way. At present, however, the mine is more than able to take care of the mill requirements.

Jan 1, 1932

By Jackson R. Pellett

INTRODUCTION The Friedensville mine is situated in Upper Saucon Township, Le- high County, Pennsylvania, in the southern central part of the Allentown quadrangle of the United States Geological Survey, approximately 5 miles southeast of the City of Allentown and 4 miles south of the City of Bethlehem. Zinc was first discovered in the Friedensville area early in the 19th century and several mines were operating during the latter part of the century. Zinc oxide was produced in 1853 and zinc metal in 1859. All mining in the area ceased in 1893 chiefly because of an unfavorable economic situation caused by a severe ground water problem and competition from the higher grade ores in New Jersey. Property acquisition by the New Jersey Zinc Company began in 1899 and periodic exploratory drilling was carried on until 1940 when sufficient reserves were proved for development of a mine. Shaft sinking was undertaken in 1947 and, due to severe hydrologic conditions, was not completed until 1952. Production began in 1958 and today the mine is producing about 64,000 tons of zinc concentrate per annum. The concentrates are trucked to the Company's smelter at Palmerton, Pennsylvania, approximately 30 miles north of Friedensville. The mine also produces from its mill tailings industrial and agricultural grades of limestone for commercial markets.

Jan 1, 1970

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydro-separation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement.† About 3130 tons of limestone, 620 tons 0f clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5,800,000 bbl, of cement. Following are some of the cement requirements of the Shasta Dam specifications: [PERCENT Chemical composition: Loss in ignition2.25 Insoluble residue0.75 SO32.25 MgO5.00 Uncombined lime in clinker (CaO)1 .25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 3,5 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O7)Not more than 7 Tetracalcium aluminoferrite (4CaO.A12O3.Fe203) Not more than 0 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength-in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1941

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. [t] About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5.800,000 bbl. of cement. Following are some of the cement require¬ments of the Shasta Dam specifications: [PER CEN'I Chemical composition: Loss in ignition2.25 Insoluble residue0.75 S032.25 M905.00 Uncombined lime in clinker (CaO)T.25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 35 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 6,5 Tricalcium aluminate (3CaO.Al203)Not more than 7 Tetracalcium aluminoferrite (4CaO.A1203.Fe203) Not more than 20 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following: [ ]

Jan 1, 1941

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements Construction of the plant, haying originally a design capacity of 7000 bbl of cement per clay, was started in June 1939, and the first clinker was ground on the following Christmas Day At present the capacity is about 12,000 bbl of finished cement per 24 hr , most of the production being low-heat cement † About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output Occasionally iron oxide is added to the clay to obtain the desired composition This, together with the gypsum, is purchased from outside sources Up to the present time, the corporation has produced low-heat, normal, moderate¬ heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements Most of the present production is for Shasta Dam, near Redding, Calif , the told demand being 5,800,000 bbl of cement Following are sonic of the cement requirements of the Shasta D [im] specifications [ ] The average specific surface in the bin s sampled shill be not less Ulan 1800 sq cm per gram and no individual sample less thin 1600 sq centimeters Compressive strength The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2 75 parts fine testing sand, by weight, shall be equal to or greater thin the following

Jan 1, 1941

By J. R. Hart, V. C. Smith, V. P. Babarovich-Hansen, J. H. Schubert

"An introduction and case study of Mintek's latest generation of Milling Circuit controller, the MillStarTM with IES (Interpreting Expert System) is presented. This paper also describes as a case study its installation on a Southern African base metals concentrator plant which has demonstrated improved operation, greatly reduced variation in product quality, as well as increased capacity and availability of the circuit.In this case study, the MillStarTMw as installed along with several other enhancements, including hydrocyclone underflow monitoring, product particle size estimation and flotation circuit stabilisation. MillStarTM utilised the particle size measurement to control grind to within 2% of setpoint, all the while ensuring sump level control, density control as well as mill power optimisation. Mintek' s expertise in the modelling of tumbling mills allowed the development of a specialised optimising controller that ensured the mill was kept in the most efficient operating region.MillStarTM augments the automatic control with useful user interface features, such as on-line trends of any logged variables, historic data warehousing and retrieval and production summary reports.A novel feature that distinguishes the MillStarTMi s the IES (Interpreting Expert System). This is a feature of the software that works with the automatic control code to generate explanations for control actions made by the controller. Often complex control systems are mysterious in nature, reducing trust and eventually resulting in them being switched off. The IES method of exposing the heart of the controller has proved popular and is seen to have potential as a training tool. 314"

Jan 1, 2000

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By O. P. Dolph

SPANIARDS were probably the first to mine the rich surface ore in the veins cutting the rhyolite capping that outcrops on the hills of La Mazata, oil the Allyones side of the Magdalena valley in Jalisco, Mexico, although the name comes from a word of Indian origin meaning "deer". The camp is about 12 km. west of Magdalena, a town on the Southern Pacific Railroad, and about 17 km. north of Etzatlán, on the Mexican National Railroad, at an elevation of 4500 ft. The climate is subtropical with no extremes of heat or cold, the rainy season beginning in June and ending in October.

Jan 1, 1938

By J. M. Morris

THE point to be made most clear in this paper is the economic value of flotation in the Benguet mill flow sheet. It is rather a statement of effect with no attempt at a technical explanation of the cause. Certain well-known, easily understood reagents, mechanisms and principles have been adapted to the conditions at Benguet, and have proved to be more successful than was demonstrated in the laboratory. The mechanical and metallurgical development of this particular operation was arrived at by trial and error, with fortunately very little error. Changes were slow, of necessity, which in the end proved a blessing in that time was afforded for observation and analysis of the disturbing factors; and as a result each change was a definite step towards higher efficiency. Many of these steps were unpredictable from labora-tory work because of the varied and differing characteristics of ores met with in daily operation of the mill, which were practically impossible to reproduce on a laboratory scale. The Benguet mill receives daily ores that differ as much as if they were delivered from three different properties. There is first the surface and upper-level zone, which produces an oxidized secondary ore contain-ing considerable iron oxide, manganese oxide and some organic matter. Formerly, most of this ore consisted of very soft fill with some hard rock mixed in. It also contained an unusual amount of iron and aluminum sulfate, which formed hydrates upon entering the alkaline cyanide solu-tion and caused excessive frothing. When flotation was introduced in the Benguet mill the general char-acteristics of this upper-level ore had changed considerably, in that it was practically all newly mined, fairly hard ore. It still contained many of the same disturbing elements, but was somewhat simpler to treat than formerly. The small proportion of fines is still troublesome in flotation, and plant practice probably does not show more than 80 per cent extraction on this small portion of the ore. No definite figure on this is available, as this particular ore is delivered at irregular intervals

Jan 1, 1936

By Stuart M. Jones

This paper describes the state of the art of grinding in the Copper Industry today including descriptions of the largest equipment and design features which allow processing of as much as 100,000 mtpd in a single mill line. We include a typical flowsheet, control philosophies, and maintenance techniques which result in low cost production which is essential in today's market.

Jan 1, 1999

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023

By W. L. Zeigler

THE year 1930 in the Ceur d? Alene district was one of curtailment in production. Many of the small properties were closed entirely and only three large. producers, the Bunker Hill & Sullivan, Hecla, and the Morning mines were left producing at capacity. No innovations in milling were evident, but progress was made in reducing costs as is always necessary in times of low metal prices. One new concentrator was constructed, a 500-ton daily capacity selective flotation plant for, the Jack Waite Mining Co. This mill uses coarse crushing, followed by hand sorting, for both a high-grade ship- ping ore and waste. The remainder of the ore leaving the sorting belt is crushed in a new type Traylor reduction crusher to %-in. size and stored in large capacity mill ore-bins. The grinding is done with ball mills, in closed circuit with a Dorr classifier to 75 per cent - 200 mesh. Minerals Separation 24-in. flotation machines are used both for a lead and a zinc concentrate, with double cleaning in each case. The concentrates are dewatered in Dorr thickeners and filtered on Oliver late-type filters.

Jan 1, 1931