Search Documents

By Charles Wright

AT most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bull-dozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1935

By Carl Allen

INTRODUCTION IN any discussion of mining one is repeatedly confronted with the difficulty of dealing with so many variable conditions. It is not an exact science and in the choice of a method each varying factor has a certain weight, which, in many cases, experience alone can determine. In mathematical terms, it is a function of many variables. A discussion of mining also loses much of its value unless, costs are considered, because the expectation of profit is the only excuse for carrying on mining at all. As conditions vary they cause fluctuations in cost and there are few operations to which a definite cost can be assigned. The character of the ore may make it difficult to drill, yet because of the ease with which it breaks the total cost of drilling and blasting may be low. In preparing this article the attempt has been, not to cover the whole field of mining, but to describe the different methods of stoping and mining which have distinct principles. In addition to this an effort has been made to show the advantage of dissecting the methods into their detailed operations and applying to these a mathematical study as an aid to the judgment in determining which is the best method to adopt, or in attempting to reduce the cost of a method already in use. Methods of mining include stoping, caving, and various methods of working large deposits which, in addition to the method of actually breaking the ore, require elaborate and definite plans of, development of the orebody. The ordinary methods of stoping are too familiar to all for any elaborate discussion, but it has seemed advisable to review the subject and give the principal advantages' and disadvantages of the different methods.

Jan 8, 1914

By Graham Crutchfield

THE W. I. Cook pool in Shackelford County, Texas, has been the subject of a number of papers and articles. Its unique position both as to operation and development has made it an ideal location for unit repressuring. The major portion of the pool is located on the W. I. Cook ranch and most of the oil leases are owned by Roeser & Pendleton, FIG. 1.-PRODUCING SAND CONTOURS, COOK POOL, JAN. 1, 1931. Inc. and the Continental Oil Co. and operated by Roeser & Pendleton, Inc. The Humble Oil & Refining Co. and Tom James operate producing leases which have a vital bearing on the unity of the pool. Both have cooperated in the repressuring project. Practically the entire royalty is .owned by Mrs. W. I. Cook and she has given the operators her entire cooperation in all phases of unit repressuring.

Jan 1, 1931

Mining regulatory authorities worldwide mandate frequent inspection of winder ropes used in shaft-equipped underground mines and ski lifts. Visual inspections are effective in identifying and assessing the type and severity of damage found in the exterior of the rope. In addition, electromagnetic or permanent magnet-based methods are used to identify broken wires, corrosion damage and other anomalies that occur anywhere within the core of wire ropes made of steel, which is a ferromagnetic material. The magnetic methods yield the loss of metallic area due to wire breaks and other damage in the ropeÆs section as well as local flaws that give rise to discontinuities in the magnetic field. The quantitative measurement of the loss of metallic area is indirectly related to the loss of breaking strength that is commonly used as a rope discard criterion. The ropes used in a mine winder in the Goldfields of Western Australia are inspected using Meraster 120B permanent magnet-based rope tester and their condition is assessed against published discard criteria.

Jan 1, 2003

By R. Debkowski

Mining methods used to protect the workings in underground salt mines against the destructive activity of natural factors are presented in this paper. Major hazards and methods of elimination of their impact on the stability of workings, were determined. Old and modern technical means and technologies used for protection and preservation of the selected most interesting sites were characterized. The results of surveys and studies allowed proposing the change of mine structure i.e. dividing it into monumental and not-monumental part, which should improve execution of necessary protective works.

Jan 1, 2006

P'his per describes the training and methods development programme in the Concen- trators at Isa Mine. The benefits of such a prosoo .n:e '.__-. _ 'ueen highlighted.

Jan 1, 1978

By Vaughan R. Voller

"Numerical methods for dealing with a temperature dependent conductivity are discussed. An approach based on a local application of a Kirchhoff transformation at the discrete level is presented. The application of this transformation - that does not require any inversion- is demonstrated on solving a two-dimensional test problem.IntroductionMuch is said in the recent literature on the modeling necessity of obtaining appropriate thermo-physical properties; in particular the requirement to account for properties that are ""strong"" functions of the depended variables, e.g., Temperature. Of course obtaining appropriate thermo-physical properties serves no purpose unless they can be accurately integrated into a discrete numerical calculation. The purpose of this paper is to examine how temperature dependent conductivities that exhibit discontinuities or rapid changes can be handled in a numerical code.The discussion will be made in the context of a control volume finite element method [1]. After a brief outline of control volume finite element fundamentals basic methods of dealing with discontinuous or rapidly changing thermal conductivity are discussed. This is followed by the presentation of the recently proposed local Kirchhoff method [2,3], The paper concludes with an investigation of the performance of the various conductivity schemes in solving two dimensional problems. This testing clearly shows the advantages (accuracy and implementation) in using the local Kirchhoff method."

Jan 1, 2001

By G. A. Hazen, S. M. Sargand

This study monitored longwall mining subsidence profiles over three panels that were mined beneath state highways in southeastern Ohio. The average maximum subsidence was 1.07 m (3.5 ft). The average maximum compressive strain recorded was 0.008 mm/mm. Three predictive methods for the determination of displacements and strains were compared: the National Coal Board (NCB) graphical method, the profile method with empirical constants determined for southeastern Ohio, and a finite element excavation program. Excellent subsidence agreement was found with the profile method, and reasonable strain agreement was determined with the finite element program.

Jan 1, 1987

By P D. Munro

The spatial distribution of ore with similar processing properties or domains within an orebody may be identified early in the assessment of an orebody to provide a sound basis for later development of the orebody. The assignment of domains in the primary sulfide portion of an orebody is often more difficult than recognition of the oxidised, supergene and related domains usually located towards the top of the mineralised volume. This paper will discuss some approaches to assigning domains within the primary sulfide portion of an orebody. The processing properties of each mining block will be known if the contained domain(s) and their proportions are known. The use of both physical and chemical ore properties to assign the domains is discussed. The domains based on similar processing properties do not necessarily coincide with geological zones assigned by geoscientists. As part of assessing the physical properties of ore, the modal analysis of the ore with respect to the valuable sulfide minerals and the sulfide and non sulfide gangue minerals has to be known, along with the traditionally used elemental assays for valuable and penalty elements. Two scales for determining other physical ore properties will be considered: the mesoscopic scale (examined by human eye) and the microscopic scale (examined via a microscope under high magnification). The strengths and weaknesses of the data obtained at the two scales are discussed in the paper. Broadly, data collected at the mesoscopic scale are much less expensive but the types of data available are more limited. Methods for evaluation of chemical ore properties are also discussed. After establishing a basis for establishing the spatial distribution of domains, variability testing is required to verify the integrity of the designated domains. In contrast, each block of ore in some orebodies has been assessed principally via the results of a laboratory separation on a number of drill core samples or composites from throughout the block, with minimal or no attention to the concept of domains.

Jan 1, 2008

By L. P. Fatti

An important feature affecting the classification of a remotely sensed scene is that the data are, in general, spatially correlated. Various approaches are discussed towards incorporating the correlation between neighbouring pixels when they are classified on the basis of their spectral reflectance data.

Jan 1, 1987

By Fred N. Kissell, Jerry C. J. Tien, Edward D. Thimons

At coal mine working faces, simultaneous application of three basic elements reduces the methane explosion hazard: (1) adequate ventilation, (2) regular monitoring of gas concentrations, and (3) the elimination of ignition sources. This paper reviews the application of these elements in a manner relevant to Chinese coal mines. Adequate ventilation is provided by using the mine entries to convey air for the long distances between the mine portal and the working sections (main ventilation systems) and then using line brattice or ventilation duct (face ventilation systems) to convey air the last hundred meters to the working face where coal is broken and removed. The air quantity provided is enough to safely dilute methane and the air velocity is enough to prevent layering. Gas concentrations are regularly monitored in accordance with regulations using knowledge of the circumstances under which the highest concentrations are likely to be found. Ignition sources are eliminated by ensuring that electrical equipment does not ignite methane, that sparking from cutter picks is minimized, and that smoking by workers is strictly forbidden. Risk-reduction studies using fault-tree analysis have shown that large reductions in explosion risk only result from multiple preventive actions. For example, a ventilation upgrade or a methane monitor upgrade by itself offers risk reductions under 50 pct. A risk reduction of 90 pct. or more would typically require much more. Other studies have shown that the everyday vigilance of those working underground is as important as engineering design.

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

Provide the mining industry with a method for determining the gas content of ore bodies and associated strata for use in mine planning, Approach Samples of various rock types are collected and tested to determine gas content in conjunction with sample size, the collection method (i.e. whether the sample was collected from a core sample or by hand) mine gas emission, and the geologic location from which the sample was taken, such as near a fault, outburst area, or other geologic anomaly. How It Works Two methods were developed by the Bureau of Mines to determine the gas contents of rock samples. The first method developed involved dissolving minerals to measure gas emission. This method, however, can only be used with soluble minerals. A second method, therefore, was developed for use with insoluble minerals. With this method, the sample is crushed in a ball mill. Although the dissolution method is faster and more accurate to use, the crushing method is also advantageous because its use can more closely approximate a mining situation; the sample is crushed as in mining and the amount of gas released relates to the amount of gas that would be released during a mining operation. The dissolution method is applied to soluble minerals, such as rock, salt, or trona, in a sealed chamber. Gases released during dissolution are collected for analysis by gas chromatography. One advantage in using the dissolution method is that the test apparatus is relatively inexpensive. In addition, test can be performed at any scale, from single crystal samples to a solution mining operation.

Jan 1, 1983

By J. G. Thompson

PROJECT 8411 of the U. S. Bureau of Standards, sponsored by the Iron and Steel Division of the A.I.M.E., is an attempt to define more concisely than has been possible heretofore the accuracy and the Limits ' of usefulness of the ' various methods now in use for the determination of oxygen as it exists in ferrous materials. It originated in correspondence between John Johnston and other metallurgists, and was brought to the attention of the Iron and Steel Division of the Institute at the Annual Meeting in February, 1933. As reported in MINING AND MET,ALLURGY, Vol. 14, page 152, March, 1933, "Dr. Johnston introduced, and those present adopted, a resolution that the Iron and Steel Division of the A.I.M.E., believing that a careful comparison of the several methods now in use for the analysis of steel for nonmetallic elements such as oxygen is highly desirable, heartily endorses the proposal that the U. S. Bureau of Standards act as a clearing house " in this matter, undertaking the final preparation and allocation of identical samples to those laboratories willing to collaborate in this important question, and collate the results re- ported back to the Bureau.'"

Jan 1, 1934

By T. Bajpayee, L. Prosser, A. Iannacchione, G. Esterhuizen

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques to help identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk-analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and could provide the kind of information needed by on-site personnel responsible for worker safety to mitigate roof fall injuries.

By T. Bajpayee, L. Prosser, A. Iannacchione

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques that will help to identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and can provide the kind of information, needed by on-site personnel responsible for worker safety, to mitigate roof fall injuries.

Jan 1, 2007

By R. T. Mishler

I WISH to express my keen appreciation of the article on the above subject by Coe and Clevenger.1 It has been doubly interesting to me, for the reason that the experience recorded and the principles evolved practically parallel the results of similar investigations made by myself and others at The Lucky Tiger Mine, El Tigre, Sonora, Mex. An outline of the work at El Tigre may aid in confirming the principles expressed by Coe and Clevenger. El Tigre has the unenviable distinction of possessing a slime with a much lower settling rate than any recorded in the article discussed. Under most favorable conditions the settling rate is about one-third that reported for the Liberty Bell mill, and one-tenth that reported for the Nipissing, Golden Cycle, and Presidio mills. This slow settling characteristic of Tigre ore has necessitated careful investigation of settling phenomena throughout the various evolutions of the plant. PREVIOUS SETTLING INVESTIGATION AT TIGRE During construction work at the mill, the Metallurgical Engineer in charge, D. L. H. Forbes, ran a series of experiments on settling. His tests proved that deep settling tanks were not ordinarily necessary. The use of tanks 2 or 3 ft. in depth was suggested.2 Later experiments demonstrated that the following principles of settling applied to Tigre pulp.3 1. In settling dilute pulp, settling rates are independent of pulp depth. 2. In settling thick pulp, settling rates are approximately proportional to pulp depth.4

Jan 3, 1917

H. S. COE, St. Louis, MO. (written discussion *)-I feel much gratified that Mr. Mishler has confirmed those principles of slime settlement expressed by Mr. Clevenger and myself. I wish to state that, when we wrote the article referred to by. Mr. Mishler we had not seen his earlier article in which he gave a formula to be applied to the settling rate off feed pulp for determining thickener area required at El Tigre. It has been my experience that in cyanide work the settling area required is determined by the settling rate of the feed pulp for perhaps 20 per cent. of all of the ores to be encountered. For the other ores, the area required is greater than that indicated by the settling rate of the feed and corre-sponds to the settlement of a somewhat thicker free-settling pulp. Mr. Mishler, in his paper, has thoroughly outlined a set of tests for determining thickener capacity, which, if carefully carried out, should be entirely reliable, provided allowance is made for changes in the mill feed from time to time. Two features of his paper, I, believe; need comment. In speaking of the time required for slime to flocculate after being fed, Mr. Mishler quite properly states that the actual settling rate for the feed pulp can-not be that of completely flocculated pulp because of this time lost in flocculation. It seems to me, however, that this feature cannot be of very great importance, for the following reason: The upper zones of pulp in a thickener may be, and often are, as thin as the feed pulp. If, therefore, the feed be introduced at sufficient depth below the pulp surface to prevent agitation at the surface, there will be ample time for it to become flocculated before it becomes the surface layer, and it, will

Jan 1, 1918

By John W. Nebgen

Surface water quality is determined by complicated interactions between water and land. Runoff--the flow of waters in surface streams and rivers-¬represents the total amount of water collected in a drainage basin or watershed that appears at the outlet of the basin. As the water flows through the basin, it is in contact with land and can pick up impurities from the land. Thus, surface waters are not pure--they contain impurities, or "pollutants," in vary¬ing concentrations determined by the nature of the land which they drain. The composition of surface waters thus tends to represent a steady state equilibrium between interactions of water and land. However, when man utilizes the land in the drainage basin or watershed, the natural equilibrium between water in the runoff and the land is disturbed. Such disturbances usually effect adverse changes in surface water quality, as new equilibrium conditions between land and water are established. These adverse changes in surface water quality can be thought of as "nonpoint pollution." Esti¬mation of nonpoint pollutant loads thus ultimately reduces to determining the magnitude of the differences between water qualities before and after man's disturbance of land within a watershed. The important key in making such an estimation lies in the determination of water quality in the natural or "back¬ground" condition of the watershed. In subsequent discussion in this paper, tools for making an estimation of background water quality will be described.

Jan 1, 1975

By Dean Ilievski

Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known: This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal "best" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.

Jan 1, 1996