Search Documents

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain <0.3% Cr203, and chromite is almost always less than 50 mp in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratiform and alpine complexes tend to be either ore grade (>25% chromite) or very low grade (<2% chromite); intermediate rocks are scarce. In most complexes, large tonnages exist only in the <2% chromite rocks and the composition of the chromite in those rocks may be unsuitable for metallurgical use. Some nickel laterite districts contain more than lo8 tons of material with 2.0 to 5.5% Cr203, and hence, chromium could be a byproduct of nickel in some laterite districts. In addition, some chromiferous sand placers may contain tens to hundreds of millions of tons of material between 2 and 5% Cr203

Jan 1, 1983

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By B Clements, R Dunne, J Dioses, S Hart

In April 2003 plant upgrades in the æLow GradeÆ Cadia Hill circuit were undertaken in order to improve concentrate quality and metal recoveries from the flotation circuit. The major changes involved: circuit reconfiguration to allow all concentrates to be reground to less than 38 ¦m prior to final cleaning; increasing ball charge in the regrind mill to fully utilise all of the installed power; desliming of the cleaner scavenger concentrate to improve the circuit water balance; and the inclusion of a gravity concentrator in the regrind circuit to recover more free gold to bullion.Once the flotation circuit had stabilised under the new operating conditions concentrate launder modifications and increased froth crowding on the scavenger flotation cells permitted the introduction of stronger collectors without compromising concentrate quality or circuit stability.Twelve months on, the copper concentrate grade has increased by two per cent and metal recoveries increased by three per cent and seven per cent for copper and gold respectively. The project capital outlay of approximately $2.0 million has been repaid in less than three months. This paper will review the project from the design, construction and commissioning perspective as well as the subsequent debottlenecking exercise that was required to eventually yield the full benefits of this upgrade.

Jan 1, 2005

By Y. M. Shneerson, I. V. Fomenko, M. A. Pleshkov, E. A. Ospanov, A. A. Shakhalov, S. S. Naboychenko

Low-grade copper concentrates (with copper content less than 20%) often contain impurities such as arsenic, zinc, lead, mercury, antimony and bismuth. The pyrometallurgical treatment of such concentrates is associated with several problems, which will ultimately affect the cost and the quality of copper cathodes as well as by-products. SRC Hydrometallurgy proposed a complex hydrometallurgical technology which allows the removal of impurities and the enrichment of low-grade copper concentrates to a quality which will be more suitable for pyrometallurgical processing. Laboratory batch tests and pilot plant results for the pressure leaching steps are shown in this paper. The key parameters of the leaching steps were determined and optimized. The quality of possible by-products were also determined. The developed flowsheet includes two pressure leaching steps: pressure oxidation (POX) and hydrothermal alteration (HTA). Both operations are carried out at 170°C with subsequent flotation of POX and HTA residues and recovery of copper, zinc and lead into separate concentrates for further processing. The development of the flowsheet was based on the Balkhash Zinc Plant (Balkhash, Kazakhstan), which had been non-operational since 2009. The developed flowsheet for processing of low-grade concentrates will utilize 80% of the existing equipment of the Balkhash Zinc Plant, thus leading to a significant reduction in required capital expenditure. INTRODUCTION As the age of copper mining operations advance, copper grades continue to diminish and impurity levels increase. Therefore, copper producers are forced to look for new innovative hydrometallurgical technologies which are able to handle low-grade raw materials and solve problems associated with impurities in an economically justifiable way. New technologies allow to extract valuable components selectively and to process low-grade concentrates which had previously been marked as non-technological and economically unviable. Hydrometallurgical technologies for processing of copper-containing materials can be divided into two main categories: chloride and sulfate (atmospheric, autoclave and bacterial) based technologies. Since the 1970s, many autoclave techniques for the processing of copper-containing materials have been developed and implemented (Naboichenko, 2002; Dreisinger, 2005; Habashi, 2009; Shneerson, 2011). The mineralogical composition of the ore (or concentrates), geographical location of the deposit, distance from industrial areas, availability of existing treatment facilities, availability of skilled labor, cost of electricity and cost of neutralization are some of the factors which are usually considered when the appropriate technology is selected (Halbe, 2002).

Jan 1, 2019

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By L. W. Vigrass

Porous and permeable rocks deeply buried in sedimentary basins contain immense volumes of hot water with the potential to supply low-grade heat energy. A part of Canada with sizeable potential for low-grade geothermal energy is the northern Williston Basin of southern Saskatchewan. In this region, the University of Regina has conducted a geological study investigating the feasibility of producing large quantities of warm water suitable for space heating in the Regina - Moose Jaw area. The study has shown that the most favourable geothermal reservoirs are in the Basal Clastic Unit (Cambrian Ordovician), which, at an approximate depth of 2,000 metres has predicted temperatures of 71°C to 74°C. We anticipate sustainable flow rates from these reservoirs of 100 to 300 ms/hr. The water contains about 150,000ppm of total dissolved solids, mostly sodium chloride. It is anticipated that the sulphate content will be 3,000 to 6,000 ppm, that the dissolved oxygen and hydrogen sulphide content will be small, and that the waters will be neutral to slightly alkaline. It is anticipated that the piezometric level will be 46 m below the ground surface for reservoirs in the upper part of the Basal Clastic Unit and 141m below the ground surface for the lower reservoirs of the unit. Plans are to build a low-grade geothermal research, testing and demonstration facility at the University of Regina. To be a practical demonstration, the facility will have to handle very large volumes of water. Because of high salinity, the water will be re injected into a subsurface reservoir. We do not anticipate insurmountable problems because of salinities or as a result of corrosion provided that the waters are not aerated during handling

Jan 1, 1979

By L. E. Fischer

The background for the 630-million-dollar-plus iron ore project at Kudremukh is outlined. The system and plants for mining, crushing, concentrating, transporting via a slurry pipeline, filtering and shiploading 7.5 million metric tons of iron ore per year are fully described. The mode of operation and the problems encountered in such a transfer of North American technology to developing countries are analyzed. Difficulties encountered during construction are discussed and the progress milestones made over a two-year period are enumerated.

Jan 1, 1979

By R. W. Diamond

Low-grade ores can be designated by two main classifications: (1) simple low-grade ores, and (2) complex low-grade ores. As a rule the first type has a relatively small metal content, although low- grade iron ores contain a rather high percentage of metal. As the simple type is the one that is ordinarily in mind when the term "low-grade ore" is used, the paper will be devoted mainly to ores in this general category. Cheap treatment is the prime requirement in utilizing low-grade ores of the simple type, although in some cases the value of nonmetallic by-products, such as limestone for fer- tilizer and silica for flux, allows a little more lati- tude than in the usual situation. When the costs are divided under the three headings-mining, milling, and smelting-it is apparent that the last group will not constitute an important factor as a rule because the high concentrating ratio makes the smelting cost per ton of ore fairly low.

Jan 1, 1949

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

By F. Bourgeois, J. A. Herbst, R. P. King

The ultrafast load cell (UFLC) has proved to be an exceptionally good device for the study of the fundamental processes associated with the impact fracture of particulate material. A new high- sensitivity UFLC has been commissioned at the Utah Comminution Center for the study of low-impact energy single-particle fracture. The force-time histories of individual fracture events have been measured. The force and energy absorbed at crack initiation have been measured at several particle sizes. The mass specific energy for fracture and the associated breakage function have been determined. The distributions of particle breakage energy and particle strength have been measured as a function of particle size.

Jan 1, 1992

Lead removal has been problematic in nickel production by electrowinning from chloride solutions, as developed by Falconbridge. The C12 leach liquor needs to be diluted by electrolyte to allow precipitation of the lead prior to electrowinning. This results in higher solution purification costs and an aversion to consider lead contaminated (secondary) feeds. In this paper, the electrowinning of nickel chloride is carried out in a membrane equipped electrolytic cell. When lead containing nickel solutions are fed into the anode compartment and the anolyte is separated from the catholyte with a cation exchange membrane, lead remains in the anolyte due to the presence of a negatively charged chloride complex. The positive nickel ions migrate preferentially through the membrane to the catholyte, allowing a lower lead nickel cathode to be produced. Lead concentration in the catholyte and the cathode product has been tested as a function of lead concentration in the anolyte. Results are presented and discussed.

Jan 1, 1998

By E. Douglas Sethness

The uranium industry is booming. In Texas alone, there are about 22 different companies with active exploration programs. Twelve solution mines have been permitted; three surface mines have been authorized; and two mills are currently in operation. However, the industry also has a problem, and that is the disposal of radioactive wastes. Over the past several years, stories concerning nuclear wastes have appeared frequently in the news. One of the most frequently cited cases occurred in Grand Junction, Colorado. In 1966, after ten years of investigations, the U. S. Public Health Service (PHS) discovered that tailings from a uranium mill were being used as fill material and aggregate for local construction purposes. It was estimated that between 150,000 and 200,000 tons of material had been removed and used under streets, driveways, swimming pools, and sewer lines. In addition, tailings had been used under concrete slabs and around foundations of occupiable structures. Further studies prompted the Surgeon General to warn that the risk of leukemia and lung cancer could be doubled at the measured radiation levels. More recently, the L. B. Foster Company discovered that its building site in Washington, West Virginia, was radioactive. While digging a foundation, the ground erupted and a ball of fire 30 feet high shot out. Evidently, the dirt was laced with radioactive thorium and zirconium, a potentially explosive mixture contained in a Nigerian sand which had been used by the previous site owners in the manufacture of nuclear fuel rods. Just this month we have read about legal suits to stop exploration for a nuclear waste disposal site in Randall County, Texas. The U. S. Department of Energy is trying to locate a deep underground nuclear waste depository for final burial of over 76 million gallons of high-level wastes. The problem is acute, the wastes are accumulating at a rate of about 300,000 gallons per year. Nor do these numbers include the spent fuel elements from nuclear power plants that are in temporary storage facilities. Fortunately, public awareness of these and other related issues is high. Unfortunately, the differences in the waste products from the nuclear fuel cycle are not always apparent to the general public. There are two distinct types of radioactive wastes: "high-level", which consist of spent fuel or wastes from the reprocessing of spent fuel; and "low-level", which, in general, are by-product wastes. There are numerous non-technical definitions that can be applied to help the layman differentiate between high-level and low-level wastes. For this latter purpose, it is best to think of them in terms of what we can see and feel. In general, high-level wastes are physically hot and can cause acute radiation sickness in a short period of time. Low-level wastes are not hot, but may cause chronic health effects after long exposure. The wastes which we are concerned with in the uranium mining and milling industry are low-level wastes. As recently as ten years ago, there were very few controls or regulations governing tailings disposal methods. At the same time, mine reclamation was not enforced through either state or Federal laws and the long-term viability of abandoned tailings ponds was not assured. The regulatory climate has changed significantly in the last decade, however. The low-level radioactive wastes generated by uranium mining and milling are generally contained in a tailings pond. Approximately 85-97% of the total radioactivity contained in uranium ore is present in the mill waste that goes to such tailings ponds. The isotope Radium-226 is probably the most potentially harmful radioactive parameter in the ponds. Radium emits gamma radiation and is also an alpha particle emitter. Because gamma radiation is very penetrating, it presents a potential health problem when a source is located external to the body. Gamma radiation will go through the body, causing damage to each cell encountered on the way. Although alpha particles have very little penetration capability, they can cause extensive cell damage. For this reason, alpha particles are a problem after inhalation or ingestion. Radium creates a health hazard by both of these mechanisms. Radium decays to radon gas which can be inhaled and serve as an alpha particle emitter. Additionally, radium is very soluble and readily enters the natural hydrologic cycle if allowed to leach from a tailings pond. With a half-life of 1620 years, radium has plenty of time to be taken into the food chain and end up in our bodies, emitting alpha particles. Because the potential health problems are better understood today than ten years ago, and because the Nuclear Regulatory Commission (NRC) has developed increasingly stringent government regulations, the uranium mining industry applies a high level of technology to the disposal of nuclear wastes. In most cases, low-level radioactive wastes are disposed of at or near the site where they are produced. There are six commercial burial grounds for low-level wastes, but it would not be economical to ship all mine or milling wastes to these sites. The on-site disposal methods most often used are ponding

Jan 1, 1979

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018

By Virgil A. Marple, Susanne V. Hering

"5.1 IntroductionTraditional impactors do not offer much size resolution for submicrometer particles; typically their finest size cut is around 0.4 µ.m. Yet for many aerosol applications it is useful to be able to size segregate aerosols in the size range below 0.4 µ.m. Diesel emissions, welding fumes, cigarette smokes and photochemically generated smog aerosols typically exhibit mass median diameters between 0.1 and 0.6 µ.m. When sampling these aerosols with a traditional impactor, fifty percent or more of the aerosol mass can penetrate the final impactor stage. Allhough the material can still be collected on a backup filter, the filter gives no size resolution. As a result, the investigator has no size information on a substantial portion of the sample. One needs a sampler that size-segregates the majority of the aerosol mass. A lower size cut of 0.1 µ.m or less is required for most combustion smokes and smog aerosol s.To obtain smaller cutpoints two types of impactors have been developed, namely low-pressure impactors and micro-orifice impactors. Both instruments can provide cutpoints as small as 0.05 µ.m. Low-pressure impactors were introduced more than twenty years ago (Stem et al., 1962), and a variety of these samplers are in use today. Micro-orifice impactors have been developed at the University of Minnesota within the last five years (Marple et al., 1981 ). To date theirs are the only examples of these instruments in use.5.2 Operating PrinciplesThe low-pressure and micro-orifice impactors use two different approaches to achieve their very small particle-size cuts. Low pressure impactors resemble ordinary impactors, but are operated at reduced pressures of 5-40 kPa (0.05 - 0.4 atm). They take advantage of the decreased aerodynamic drag on particles that occurs when the mean free path in the air is as large or larger than the particle diameter. Micro-orifice impactors operate at near atmospheric pressure, but employ very small orifices, 40 µ.m to 200 µ.m in diameter. The streamlines of the air impinging upon the impaction plate have correspondingly smaller radii of curvature; the air is accelerated more quickly, making it more difficult for the particles to follow. The basic operating principles for both types of impactors are evident from the particle Stokes number, defined as:"

Mar 1, 1989

By Andrew J. Petruska, Austin F. Oltmanns

The paper proposes a capacitive load cell for detecting changes in material and tool wear conditions for conical picks used in underground mining. The current process is dangerous and subjective, relying on human operators near the cutting interface. The new sensor aims to improve worker safety by allowing operators to perform their functions from a greater distance.

Aug 1, 2023

By Andrew J. Petruska, Austin F. Oltmanns

This work proposes a capacitive load cell for conical picks to enable underground continuous mining machine operators to perform their roles away from known hazardous regions near the machine. The load cell is embedded in commercially available flexible printed circuit board, integrates with the target tooling, and demonstrates in situ force sensing of vibration signatures for continuous mining cutting tools. Changes in material constitution, tool mass, and tool geometry cause modal variations in vibrational response measurable with force sensors at the cutting interface. Time-series measurements are captured during rock cutting tests using a linear cutting machine. These measurements are segmented into small windows, less than 0.25 s, and are preprocessed using the fast Fourier transform, which highlights the modal variations. The transformed measurements are then classified into different material and wear categories using support-vector machines with the radial basis function kernel. Different normalization schemes and Fourier transform methods are tested for signal preprocessing. Results show that the power spectral density measurements with normally distributed coefficients give good results for material classification, while the normalized time-domain measurements give better results for wear classification. Under laboratory conditions, this technique is shown to classify material and wear categories with F1 score above 0.85 out of 1.0 for our experiment. This technology could be used to assist operators in assessing material and wear conditions from a safer distance. It has applications in the coal mining industry as well as other applications which use conical picks such as road milling.

Mar 25, 2023

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal&apos;s organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors&apos; recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By P. D. Rao, D. E. Walsh

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal&apos;s organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherit and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors&apos; remit research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Feb 24, 1997

By Roger E. Scholl

Data on off-site low-rise building damage from underground nuclear testing at the Nevada Test Site (NTS) of the United States Atomic Energy Commission (AEC) [The AEC has been called the United States Energy Research ant Development Administration (ERDA) since 1975, but because the data presented here were gathered between 1966 and 1970, the AEC rather than ERDA is referred to in this paper.] are available for seven large tests in the period from 1966 to 1970. The data, while sparse, provide an adequate sample for the investigation of motion-damage relationships. Damage in the study is statistically described in terms of the incidence of damage complaints, the incidence of buildings damaged, and damage cost. Using 5%damped response spectrum acceleration amplitude to characterize ground motion, the plotted data fit reasonably well with previous motion-damage relationships established from extensive data available from the 1969 RULISON underground nuclear explosion (UNE) experiment conducted in western Colorado.

Jan 1, 1976