Search Documents

By H. G. Doll

An earlier paper on the general subject of the SP log has analyzed the limitations of that log, in particular when dealing with thin permeable beds enclosed in thick highly resistive ones. Under such conditions, the SP log does not give a good definition of the permeable beds. Selective SP logging is a new method which gives an accurate determination of the permeable beds; even in highly resistive formations, except when the salinity of the mud is extremely high. It also permits a close approxi. mation of the static SP to be obtained. The method consists generally in controlling the potential of auxiliary electrodes located in the drill holes in the vicinity of the measuring electrode. In this manner. the flow of SP current along the drill hole is modified to counterbalance the effect of highly resistive strata. Several procedure; and arrangements used to record selective SP curves and static SP curves are explained. Field examples illustrating these methods are given and discussed. INTRODUCTION In an earlier paper,' the shape of the SP curves and the amplitude of the SP peaks were analyzed, considering how the circulation of the SP current is influenced by the subsurface media as a function of their geometrical configuration and their resistivities. It was shown, in particular. that the permeable beds situated between highly resistive formations are sometimes indistinctly indicated by the deflections of the SP log. It is the purpose of this paper to dircuss a new method now being developed, namely selective SP logging, whose principal feature is to enable a more accurate determination of the depths of the permeable beds present in highly resistive formations, such as occur in limestone fields. It will be shown also how an addi-tional curve called the static SP log can be derived from the selective SP log, or recorded directly, to facilitate the interpretation. Another purpose of the static SP log is to provide an approach toward the determination of the value of the static SP, where this value is not readily given by the SP log. This application. although less important at the present time than that mentioned above, nevertheless is of interest, inasmuch as, according to laboratory and field experiments conducted by several investigators, the determination of oil saturation of reservoirs from the data of the electric log implies the knowledge of the resistivity of the connate water,2,3 to which the static SP seems to be related.4,5,6,7 PRINCIPLE OF SELECTIVE SP LOGGING The method of selective SP logging of the formations traversed by a bore hole consists in recording two curves under the following conditions: The measuring device comprises one measuring electrode M and two additional electrodes G-G', connected to each other. located above and below

Jan 1, 1950

By Robert E. Bush, E. S. Mardock

The objective of this paper is to present practical methods of applying radioactivity logs to problems of interest both to those engaged in evaluating fundamental reservoir data as well as to those engaged in subsurface structural work. The basic theories underlying the operation of radioactivity logging methods are briefly discussed along with some of the problems arising in the interpretation of the log. Relative methods of quantitative interpretation are described, with a discussion of relative reference lines and specific examples are given showing the application of these relative quantitative interpretation methods. To show the variation of the methods described, specimen wells penetrating formations widely divergent in point of geologic age were selected to demonstrate the application. A relative reference line is determined for the Neutron Curve and by comparison to known petrophysical data such as porosities from diamond cores, a direct quantitative relationship is developed. The application of this relative calibration curve to logs of unknown wells will permit a reasonably accurate determination of porosity in limestone and dolomite formations. Specific examples are given showing the application of these relative methods of interpretation to logs of the Smackover limestone in Louisiana, the Edwards limestone and dolomites of South Texas, and Permian dolomites of West Texas. Radioactivity logs have been used extensively by the petroleum industry for a number of years and recognition of their value has grown steadily, not only as tools to aid in the solution of specific stratigraphic problems, but also as potential sources of the basic data necessary for the estimation of net pay and reserves. The value of radioactivity logs for stratigraphic work has been pointed out in the literature,1,2,4,5,6 and now has long been recognized by the industry, but the quantitative application of the logs has advanced but little beyond the stage of a strong conviction that radioactivity logging curves will some day provide the information on such important quantities as the porosity and the liquid saturation of the formations. During the past few years the staffs of the Lane-Wells Company and Well Surveys, Incorporated, have devoted a great deal of time, thought, and experimentation to the relationships existing between radioactivity curves and the lithologic conditions encountered, and this paper is, in a manner of' speaking, intended as a progress report of this work and includes suggestions which the authors have found useful in the interpretation of radioactivity logs. The section on theory is not intended as a complete exposition of the physical processes involved, but rather as a brief introduction to the reader of these processes so that he may acquire a better understanding of the behavior of the radioactivity curves under the varied conditions encountered in normal well logging. Three relative methods for using neutron logs for the quantitative estimation of porosity in limestone or dolomite are presented. These methods are based on the comparison of logs and porosity data from wells in Louisiana, South Texas, West Texas, and New Mexico. These areas were selected because not only were there more core data available from these areas but also the majority of these data were from limestone or dolomitic zones. The correlation between core data and logs is simpler for limestones and dolomites than it is for sandstones due to the fact that sandstones are more complex than limestones and differ more widely among themselves as to composition of cementing materials, siltiness, etc. When data applicable to the various types of sandstones are available, the authors hope to present a discussion similar to this paper covering sandstones or possibly a more general discussion covering all types of reservoir rocks. The relative methods for estimating porosity which are presented in this paper fall short of the absolute method sought. However, these methods possess the advantage that they can be applied to almost any neutron log as long as the range of application is held within the limits imposed by the local lithologic conditions which prevailed during calibration, i.e., these methods are for short range application only. THE THEORETICAL BASIS FOR RADIOACTIVITY LOGGING The two redioactivity logging curves commercially available today are the

Jan 1, 1950

By M. R. J. Wyllie, Walter D. Rose

The use of electrical well logs for the quantitative determination of such reservoir parameters as connate water saturation, formation permeability and connate water salinity has recently been attracting the attention of a number of workers1,2,3,4,5. While the theory of the determination of connate water salinity from the self potential S.P. log has received rather detailed treatment, relatively little attention has been paid to the theoretical aspects involved in the quantitative interpretation of resistivity data. It is clear that if electrical well logs can be used for the quantitative evaluation of physical characteristics of reservoir rock, they will provide a valuable tool to supplement cheaply information obtained by more laborious core analysis. In certain cases it is conceivable that the coring program could be considerably curtailed if the electric log could be relied upon to give reasonably accurate quantitative information. It is our object in this paper to examine the theoretical basis of quantitative log interpretation as expressed in such well-established logging concepts as formation factor and cementation factor. It is also our object to investigate the physical aspects of the rela- tionship which is presumed to exist between resistivity index and brine saturation in reservoir rock. In particular, we will endeavor to draw attention to the fact that it is possible to express these logging concepts in terms of capillary pressure-saturation relationships, permeability and tortuosity, parameters which we will consider in this paper to be fundamentally indicative of rock texture. The probability of being able to obtain from log recordings alone the data theoretically essential to permit quantitative log interpretatiou will be examined, and consideration will also be given to the problem of formulating simple semi-empirical relationships for use in the field. THEORETICAL CONSIDERATIONS The concept of formation resistivity factor, or as it is now commonly called, formation factor, appears to have been introduced by G. E. Archie",". Formation resistivity factor as defined by Archie is the resistivity of a rock 100 per cent brine-saturated divided by the resistivity of the brine. This relationship had previously been used by physical chemists and the concept is, for example, implicit in an early treatment by Fricke7 of the conductivity of aqueous slurries. Archie was able to establish the fact that although the relationship between formation factor and porosity did not change too greatly for different rock textures, the relationship between formation factor and permeability was markedly dependent on rock texture. The relationship found by Archie between formation factor and porosity was expanded by H. Guyod8. Archie had suggested that the formation factor, F, could be expressed in terms of the porosity, F, as follows: F =F-m .... (11 where, F = effective porosity fraction of the sand, and, m = an exponent greater than about 1.3. Guyod introduced the term cementation factor for the exponent, m, since it may be qualitatively shown that formation factor for any given porosity tends to increase as the sand becomes more cemented. It would appear that the concept of m as an exponent representing the cementation in a sand is strictly only of qualitative value, since the quantitative estimation of m by means other than the determination of F and F has not been possible. Guyod suggests that m can be estimated from a visual examination of a sample of rock, but this method appears to be both arbitrary and unreliable. It can be said, however, that in intergranular reservoirs of practical interest, the range of m is from about 1.4 to 3.0. A possible explanation for the fact that m is found to lie between these limits will be offered below. The determination of formation factor is an essential preliminary to the

Jan 1, 1950

By Walton J. Greer, System By John E. Owen

The guard electrode system measures the resistivity of formations by employing a thin disk of current which is caused to flow perpendicular to the bore hole. The control of this current disk is obtained in a brute force manner through the use of relatively long equipotential electrodes above and below the measuring electrode. The log obtained from the system is free of "lag," "plateau," "shadow," "reflection" and other distortions evident on conventional logs. The proportionate contributions of the hole size and invaded zone resistivity to the apparent resistivity reading are reduced when the mud and filtrate resistivities are lower. Thus, the guard system favors the use of conductive muds. The mathematical development of the theory is given in an appendix. Equations are derived to evaluate the effects of mud resistivity, hole size, invaded zone resistivity and depth, and the true formation resistivity. Sample logs from several provinces are reproduced and compared with conventional electric logs to illsutrate the much greater detailed lithology that can be presented by the guard electrode system. INTRODUCTION With increased ability of those in the petroleum industry to analyze formation characteristics from electrical resistivity data, there has become apparent the need for more precise measures of that parameter. The measurement of the resistivity of a homogeneous and isotropic material can be made simply when the body of the material is infinite in all dimensions and the measuring electrodes can be placed within the body. In such a case, the current leaving an electrode follows a spherical distribution and the mathematical expression for the potential level at any distance from that electrode can readily be derived.'.' If it is considered that the active electrodes are within a bore hole filled with mud of a resistivity different from that of the formation. the current does not flow in a spherical pattern near the current source or sink, and the calculations of potential levels become more difficult. The additional consideration of a section of formation invaded by mud filtrates, and thus having resistivity different from either that of the mud, the adjacent formations or of the undisturbed formation, makes the mathematical problem extremely complex. Should the vertical dimensions of the formations be considered as finite. the problem becomes so complex as to preclude reasonable solution. Yet, even these considerations have not described adequately the conditions encountered in a large proportion of the wells to be studied. In efforts to evaluate the effects of the various conditions. combinations of twn, three. and four electrode logging con- figurations of the conventional types have been used. The resulting logs have left much to be desired in some provinces. It has become apparent that the use of such configurations will not result in adequate measurements being made, particularly in cases where the formation is composed of thin sections. If all the current of a resistivity measuring circuit is made to flow through the formation opposite the exploring electrode, many of the shortcomings of the conventional measuring system are eliminated. In the guard electrode method of electrical well logging to be discussed in this paper, the current is so controlled by causing it to flow in a thin disk normal to the axis of the logging tool. EARLY HISTORY The guard electrode method of electrical well logging in its early years was a joint development by the Geophysical Research Corp. and the Amerada Petroleum Corp. The method was first experimentally investigated by means of model studies. The results of these studies indicated that current focusing systems properly applied to electrical well logging

Jan 1, 1951

By System By John E. Owen, Walton J. Greer

The guard electrode system measures the resistivity of formations by employing a thin disk of current which is caused to flow perpendicular to the bore hole. The control of this current disk is obtained in a brute force manner through the use of relatively long equipotential electrodes above and below the measuring electrode. The log obtained from the system is free of "lag," "plateau," "shadow," "reflection" and other distortions evident on conventional logs. The proportionate contributions of the hole size and invaded zone resistivity to the apparent resistivity reading are reduced when the mud and filtrate resistivities are lower. Thus, the guard system favors the use of conductive muds. The mathematical development of the theory is given in an appendix. Equations are derived to evaluate the effects of mud resistivity, hole size, invaded zone resistivity and depth, and the true formation resistivity. Sample logs from several provinces are reproduced and compared with conventional electric logs to illsutrate the much greater detailed lithology that can be presented by the guard electrode system. INTRODUCTION With increased ability of those in the petroleum industry to analyze formation characteristics from electrical resistivity data, there has become apparent the need for more precise measures of that parameter. The measurement of the resistivity of a homogeneous and isotropic material can be made simply when the body of the material is infinite in all dimensions and the measuring electrodes can be placed within the body. In such a case, the current leaving an electrode follows a spherical distribution and the mathematical expression for the potential level at any distance from that electrode can readily be derived.'.' If it is considered that the active electrodes are within a bore hole filled with mud of a resistivity different from that of the formation. the current does not flow in a spherical pattern near the current source or sink, and the calculations of potential levels become more difficult. The additional consideration of a section of formation invaded by mud filtrates, and thus having resistivity different from either that of the mud, the adjacent formations or of the undisturbed formation, makes the mathematical problem extremely complex. Should the vertical dimensions of the formations be considered as finite. the problem becomes so complex as to preclude reasonable solution. Yet, even these considerations have not described adequately the conditions encountered in a large proportion of the wells to be studied. In efforts to evaluate the effects of the various conditions. combinations of twn, three. and four electrode logging con- figurations of the conventional types have been used. The resulting logs have left much to be desired in some provinces. It has become apparent that the use of such configurations will not result in adequate measurements being made, particularly in cases where the formation is composed of thin sections. If all the current of a resistivity measuring circuit is made to flow through the formation opposite the exploring electrode, many of the shortcomings of the conventional measuring system are eliminated. In the guard electrode method of electrical well logging to be discussed in this paper, the current is so controlled by causing it to flow in a thin disk normal to the axis of the logging tool. EARLY HISTORY The guard electrode method of electrical well logging in its early years was a joint development by the Geophysical Research Corp. and the Amerada Petroleum Corp. The method was first experimentally investigated by means of model studies. The results of these studies indicated that current focusing systems properly applied to electrical well logging

Jan 1, 1951

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By H. G. Doll

A new electrical logging method called Laterolog is described which provides for better recording of formation resistivity. In this method a current, preferably of constant intensity, is forced into the formation perpendicularly to the wall of the hole as a sheet of predetermined thickness by means of a special electrode arrangement and of an autonlatic control system. The essential advantages of the Laterolog over the regular resistivity logs are explained. With the Laterolog, the mud column has much less influence than with conventional methods. The Laterolog is, therefore. particularly useful in wells drilled with highly conductive mud. Moreover. when the electrode system is located opposite a bed of moderate or small thickness, the disturbing effect of the adjacent formations becomes practically eliminated, provided the bed is thicker than the sheet of current. which itself is usually a few inches to a few feet thick. The sequences of beds are. therefore, much more sharply differentiated, and, in many cases, it is possible to read directly from the logs values close to the true resistivities of the formations without further corrections. Field examples are shown to illustrate the results of the method in various types of formations. INTRODUCTION As soon as it was introduced into the petroleum industry, electrical logging roved to be a powerful instrument for the delineation of the strata traversed by bore holes and for correlation of such strata." Research and engineering efforts were mostly devoted at this early time to the design of the techniqurs which could provide the best data for these purpoes. Later, attention was directed toward the quantitative analy5i.s of electrical logs, in order to obtain information on. reservoir characteristics, and, in particular, on oil and water saturation.3,4 Efforts have been made, accordingly, with a view to improving the already existing methods, or to finding new methods which could satisfy these new requirements." Quantitative analysis implies a determination as accurate as possible of the true resistivity of the formations. In fact, however; the "apparent resistivity" recorded in front of a given bed by a conventional electrical logging method is frequently quite different from the true resistivity of this bed. This is due to the combined influence of the mud column, of the adjacent formations both above and below the bed, and of the invaded zone, in which the original fluid has been more or less replaced by mud filtrate. When the beds are thick enough, and, as is frequently the case in sand and shale formations, when their resistivity is not much greater than that of the mud, it is generally possible to obtain their true resistivity directly on the electric log, or at least to obtain an approximate value which can be corrected without undue difficulty by means of recently published charts known as "departure curves."" When the beds are thin, and particularly when, in addition. their resistivity is substantially greater than that of the mud column, the apparent resistivities recorded on conventional logs are seriously affected, and it is generally very difficult, if at all possible, to estimate their true resistivity with a good enough accuracy. In the most severe cases, such as are encountered in holes drilled through hard formations with muds of high salinity, the conventional logs are so distorted and rounded that they do not even show clearly the houndaries of the different beds. In order to overcome the effect of the mud column and of the adjacent formations, it is possible to make use of appro. priate systems whereby the measurements involve a comp3ratjvelv thin slice of space at the level of the measuring device. A mention is due, in this respect, to a measuring system. called the "guarded electrode;" invented by C. Schlumberger over 20 years ago. The system, schematically represented in

Jan 1, 1951

By H. G. Doll

A new electrical logging method is described which measures the resistivity of small volumes of material near and behind the wall of the bore holes. The very small electrode systems used are supported in the face of the flexible insulator pad of appropriate dimension maintained in contact with the wall. The measurements are recorded simultaneously with two different electrode spacings. This method provides a very detailed record of the formations and particularly of the permeable beds traversed by the bore holes. The application of MicroLog to the location of permeable zones within compact formaltions, such as limestone, and to the determination of the amount of sand existing in sequences of thin shale and sand streaks is discussed. The possibility of quantitative determination, providing a step toward the evaluation of formation porosity and mud cake thickness, is also examined. Field examples illustrate the essential features of the method. INTRODUCTION In conventional electrical logging, the spontaneous potential (SP) log is used to delineate the permeable beds, and the resistivity logs are used primarily to provide indications concerning the fluid content of the beds. When the formations are much more resistive than the mud, as happens, for example, in limestone fields, the SP currents are short-circuited by the more conductive mud column, with the result that the SP log is quite rounded. In that case, the SP log generally gives the approximate location of the permeable formations but it cannot be used for an accurate determination of the boundaries of each permeable bed.' Solutions for the problem of obtaining a better determination of the permeable beds in limestone fields were developed from two angles. One approach consisted in improvements to the logging of the SP, as given by Selective SP logging and Static SP logging. These new methods, which have been described in an earlier paper,' give good results when the mud is not too salty, but they are still in a somewhat experimental stage, mostly because the development efforts have lately been concentrated on another approach to the problem, i.e., the MicroLog.

Jan 1, 1950

By M. R. J. Wyllie, H. W. Patnode

In the quantitative interpretation of electric log data it is essential to know the formation factor, defined as the ratio of the resistivity of the formation 100 per cent saturated with brine to the resistivity of the brine.' This concept implies that the formation factor for any given rock is constant irrespective of the resistivity of the brine or solution with which it is saturated. It is apparent that this can be true only when the rock matrix is wholly non-conductive. As reservoir rocks may contain clay or shale having an appreciable conductance one may expect these constituents to influence the determination of true formation factor. The formation factor may be theoretically derived from log data by dividing the resistivity of the mud filtrate invaded formation by the resistivity of the mud filtrate. Such a method of calculntion has implicit in it the assumption that the fluids in the invaded formation are wholly replaced by mud filtrate. that the solid matrix is non-conducting, and that the formation factor of the invaded zone is identical with the formation factor of the uninvaded zone. Since the validity of the first two basic assumptions regarding the insulating character of porous matrices and the displacement of the interstitial fluids in porous media do not appear to be fully established, the formation factors of a number of cores and clay slurries have been measured under conditions suitable for verifying the assumptions and the extent of any errors inherent in them. CORE STUDIES Apparatus and Procedure Resistivity measurements were made on short cylindrical permeable cores which had been previously mounted in lucite.2 The cores were clamped by means of insulated bolts between brass plates about 5 cm square and 1 cm in thickness. The plates were provided with a ring seal to prevent leakage between them and the core mount, and had a centrally located orifice so that fluids could be flowed through the mounted core. The brass mounting plates were used as electrodes and any current flow between them necessarily passed only through the constituents of the intervening core. Fluid saturation of the core, and fluid flow through the core, were effected by a centrifugal pump connected to the outflow end of the core, thus providing a differential pressure across the core of approximately one atmosphere. The procedure used was first to evacuate each core by means of the pump and then to saturate the core with an aqueous sodium chloride solution of known resistivity. The resistance of the core was measured and flow of the solution through the core continued for sufficient time to establish a constant resistance reading. After equilibrium had been reached with one solution, another sodium chloride solution of a different resistivity was flowed through the core and the flow continued until a constant resistance reading was again obtained. This procedure was continued until resistance measurements of the core had been made with a series of solutions within a salinity range from 1.0N NaCl to distilled water. The data obtained enabled the apparent formation factor of given porous rocks when saturated with fluids of different resistivity to be computed and also provided information regarding the ability of an invading fluid to displace interstitial water from a core. Results Berea Sandstone — The first core examined was a specimen of Berea sandstone." This core had been cut essentially parallel to the bedding for permeability studies. The core was clamped in the core holder and saturated with 1.0N NaCl solution and the resistance determined. It was subsequently flushed and the resistance measured when saturated in turn with 0.1N, 0.025N, 0.01N, .005N sodium chloride solutions and finally with distilled water. In flushing the core with each

Jan 1, 1950

By E. S. Mardock, Robert E. Bush

The object of this paper is to report recent developments in the quantitative interpretation of radioactivity logs. The use of reference lines is described in the application of the new zero radioactivity reference line for the determination of neutron derived porosities is discussed. Illustrated examples are shown of logs from the reef limestone of the North Snyder Field and from the Lansing-Kansas City limestone of central Kansas. A method of using an interrelation factor calculated from the neutron and gamma ray curves, called the neutron Productivity number, for the estimation of productivity from sandstone formations is discussed. When used in a relative manner the neutron productivity number has aided in Predicting whether a given zone will produce gas or liquid or whether it is too shaly to produce. Examples of logs from wells in the Freites District, Venezuela, and in East Texas are shown to illustrate the application of the neutron productivitv number. INTRODUCTION The petroleum industry was introduced to some of the preliminary results of investigations into the quantitative interpretation of radioactivity logs in October, 1949." It was stated at that time that the methods presented were entirely relative because they involved the use of reference points obtained from the radioactivity log, i.e., shale reference lines, dense zone reference lines, or a combination of both shale and dense zone reference lines. These relative methods offered many advantages to the industry in interpreting radioactivity logs in terms of porosity with particular application to limestone and dolomite reservoirs. However, these relative methods did not offer the wide range of applicability desired because the esta1)lishment of reliable reference points from shale in some areas were difficult. It was recognized that a more reliable mean; of establishing reference lines was vitally needed. Such a method is now available through the introduction of an instrumeutal zero device. It is the purpose of this paper to discuss the application of this new zero reference to the quantitative interpretation of radioactivity logs. Previously all applications of quantitative interpretations of radioactivity logs have been made in limestone reservoirs with little or no emphasis placed on sandstone reservoirs. A brief resumé of investigations into the quantitative interpretation of radioactivity logs in sandstone reservoirs is presented here. This discussion deals primarily with the interrelation of the gamma ray and neutron curves and the response of the latter to the density of the fluids filling the pore space in relatively homogeneous sandstones of uniform porosity. The authors believe that the methods presented herein are only applicable locally to specific fields and reservoirs, and that they probably do not offer a wide range of applicability. However, tile authors believe that the wider use of the new instrumental zero references in sand areas will reveal more information about the specific response of the gamma ray and neutron curves to changes in lithology and saturation. Two applications of quantitative interpretation using the new instrumental zero references are presented. Examples are given which show the comparison of logs and porosity in the limestones and dolomites of West Texas and Kansas. Logs of wells in 'Venezuela and East Texas are compared with the drill stem test data, production data, etc.. to illurtrate the interrelation of the gamma ray and neutron curve: and the rise of methods involving these interrelations to determine certain saturation variables. THE QUANTITATIVE APPLICATION OF RADIOACTIVITY LOGS TO LIMESTONE AND DOLOMITE RESERVOIRS Tile theoretical basis for the gamma ray and neutron curves has been discussed elsewhere.9 he method of recording the logs and apparatus involved has also been thoroughly covered and will not be discussed here.'."".'" It has been shown that the neutron curve responds exponentially to liquid filled porosity over the 1 1/2 to 35 per cent

Jan 1, 1951

By Robert E. Bush, E. S. Mardock

The object of this paper is to report recent developments in the quantitative interpretation of radioactivity logs. The use of reference lines is described in the application of the new zero radioactivity reference line for the determination of neutron derived porosities is discussed. Illustrated examples are shown of logs from the reef limestone of the North Snyder Field and from the Lansing-Kansas City limestone of central Kansas. A method of using an interrelation factor calculated from the neutron and gamma ray curves, called the neutron Productivity number, for the estimation of productivity from sandstone formations is discussed. When used in a relative manner the neutron productivity number has aided in Predicting whether a given zone will produce gas or liquid or whether it is too shaly to produce. Examples of logs from wells in the Freites District, Venezuela, and in East Texas are shown to illustrate the application of the neutron productivitv number. INTRODUCTION The petroleum industry was introduced to some of the preliminary results of investigations into the quantitative interpretation of radioactivity logs in October, 1949." It was stated at that time that the methods presented were entirely relative because they involved the use of reference points obtained from the radioactivity log, i.e., shale reference lines, dense zone reference lines, or a combination of both shale and dense zone reference lines. These relative methods offered many advantages to the industry in interpreting radioactivity logs in terms of porosity with particular application to limestone and dolomite reservoirs. However, these relative methods did not offer the wide range of applicability desired because the esta1)lishment of reliable reference points from shale in some areas were difficult. It was recognized that a more reliable mean; of establishing reference lines was vitally needed. Such a method is now available through the introduction of an instrumeutal zero device. It is the purpose of this paper to discuss the application of this new zero reference to the quantitative interpretation of radioactivity logs. Previously all applications of quantitative interpretations of radioactivity logs have been made in limestone reservoirs with little or no emphasis placed on sandstone reservoirs. A brief resumé of investigations into the quantitative interpretation of radioactivity logs in sandstone reservoirs is presented here. This discussion deals primarily with the interrelation of the gamma ray and neutron curves and the response of the latter to the density of the fluids filling the pore space in relatively homogeneous sandstones of uniform porosity. The authors believe that the methods presented herein are only applicable locally to specific fields and reservoirs, and that they probably do not offer a wide range of applicability. However, tile authors believe that the wider use of the new instrumental zero references in sand areas will reveal more information about the specific response of the gamma ray and neutron curves to changes in lithology and saturation. Two applications of quantitative interpretation using the new instrumental zero references are presented. Examples are given which show the comparison of logs and porosity in the limestones and dolomites of West Texas and Kansas. Logs of wells in 'Venezuela and East Texas are compared with the drill stem test data, production data, etc.. to illurtrate the interrelation of the gamma ray and neutron curve: and the rise of methods involving these interrelations to determine certain saturation variables. THE QUANTITATIVE APPLICATION OF RADIOACTIVITY LOGS TO LIMESTONE AND DOLOMITE RESERVOIRS Tile theoretical basis for the gamma ray and neutron curves has been discussed elsewhere.9 he method of recording the logs and apparatus involved has also been thoroughly covered and will not be discussed here.'."".'" It has been shown that the neutron curve responds exponentially to liquid filled porosity over the 1 1/2 to 35 per cent

Jan 1, 1951

By H. G. Doll

As a continuation of the earlier paper on the general subject of the SP log, a more complete analysis of certain features of the SP log in shaly sands is given. The pseudo-static SP in front of shaly sands is compared, on a theoretical basis, to the static SP in front of clean sands, as a function of the respective amount of shale and sand in the formation, and of the relative resistivities of the shale, of the uncontaminated part of the sand. and of the invaded zone of the sand. As a conclusion, the advantage of using reasonably conduc. tive mud in this case is shown. The discussion is illustrated by field examples. INTRODUCTION The discussion reported in the present paper is based on a theoretical analysis, and not on experiment. The field examples, joined to the text. are shown only as qualitative illustrations of the essential results of this analysis. Although the hypotheses made in the theoretical developments may perhaps be somewhat improved, it seems, nevertheless, that the results obtained account reasonably well for the actual phenomena, and give a fair approximation of their order of magnitude. The paper contains a mathematical analysis of a tri-dimen-sional distribution of potentials and current lines. due to spontaneous electromotive forces arising at the contact of shales and free electrolytes. as a function of the geometry and of the respective resistivities of the different media involved. It is assumed, although this hypothesis is not proven, that the emf's remain the same even if the shale occurs in very thin layers or in dispersed particles. It has already been pointed out 1,2,3 that, all other conditions being the same, the deflection of the SP log in front of a shaly sand is smaller than opposite a clean sand. When the thickness and the conductivity of a clean sand are large enough. the deflection of the SP log reaches a limiting value which is equal to the "static SP" of the clean sand. It is generally convenient to take the static SP of shale as the reference value or "base line." As a consequence, and for the sake of abbreviation, the expression. "static SP of a clean sand," is often used to designate the difference between the static SP of that sand and that of the shales, which difference is a measure of the total electromotive forces involved in the chain mud sand-shale. A similar limiting value is; also observed for the SP deflec-lion opposite a thick shaly sand, but it is smaller. just as if the total electromotive force involved were smaller in that case. This limiting value has been called the "Pseudo-Static SP" of the shaly sand. The static SP of a clean sand depends on the salinity of its connate water with respect to that of the mud, and, to a certain extent. on the differential pressure which controls the electro-filtration potentials, but it does not depend on the resistivity of the sand. On the contrary. the pseudo-static SP of a shaly sand depends not only on the salinity of its connate water and on the differential pressure, but also on the percentage of shale and on the resistivities of the shale, of the uncontaminated part of the sand, and of the zone invaded by the mud filtrate. If the three resistivities above were equal, the pseudo-static SP would be proportional to the percentage of sand in the shaly sand, and its departure from the static SP of a clean sand having the same connate water would simply be proportional to the percentage of shale. In that case, the pseudo-static SP of a shaly sand containing 10 per cent of shale would he 10 per cent less than the static SP of a clean sand. When. however. the sand is. on the average. substantially more resistive than the shale. the percentage of departure of the pseudo-static SP from the static SP of a clean sand is much larger than the percentage of shale. For that reason, the peaks of the SP log opposite shaly sands are systematically of smaller amplitude when the sands are oil-bearing than when they are water-bearing, all other conditions being the same. This feature is observed even when the sand beds are thick. and even when they do not contain a large percentage of shale. All this has already been described in all earlier publication", but mostly in a qualitative way. The present paper will analyze in more detail the action of the local SP currents which are generated inside of the shaly sands, and which are responsible for the abnormally low value of the pseudo-static SP. The quantitative computations have been extended to the general case of thin interbedded layers of sand and shale, where the resistivities of the shale and sand streaks do not have the same value: they are summarized in charts giving values of the pseudo-static SP of a shaly sand as a function of the different parameters involved. DEFINITIONS The static SP of a clean sand has been defined as the potential that would exist in the mud opposite that sand, were the SP current prevented from flowing. Such an ideal condition is represented on Fig. I-A. By analogy, the pseudo-static SP of a shaly sand can be defined as the potential that would exist in the hole, if the circuit shaly sand — surrounding shales — mud column were interrupted by the insulating plugs placed at the boundaries

Jan 1, 1950

By M. H. Waxman, M. Gondouin, H. J. Hill

Streaming-potential experiments were conducted within the Muddy- and Dakota-sandstone interval of a Denver basin well. Analysis of the data shows that, for this case, streaming potentials opposite sands were higher than those opposite shales when the mud was fresh. Streaming potentials opposite shales, however, were of sufficient magniiIlde to be important in SP interpretation. They were linearly dependent upon pressure differential, and they increased with mud filtrate resistivity. The magnitude of streaming potentials opposite sands was influenced by the characteristics of the original mud cake formed at the time of drilling. Use of mud samples taken at the time of logging may not always be satisfactory for determining streaming-potential corrections. Both the streaming and electrochemical potentials were found to be affected by the previous history of the borehole system. Following a change in mud characteristics, several days were required for SP stabilization. This was, in part, due to the mud cake acting as an imperfect shale membrane. INTRODUCTION Laboratory investigations by Wyllie,1 Salisch,2 Moore," Sen Gupta and Bannerjee,0 and Hill and Anderson' have shown that streaming potentials developed across mud cakes deposited on permeable filter beds are of sufficient magnitude to be critically important in SP interpretation. Streaming potentials across shales have been reported by Schenck,' Gondouin and Scala; and Hill and Anderson." The magnitude of the shale streaming potentials obtained by Schenck and by Gondouin et a1 led these authors to conclude that in many cases the shale streaming potential would approximately equal the mud-cake streaming potential. Hill and Anderson, however, obtained somewhat lower magnitudes of shale streaming potential. The field experiment described in the present paper was a cooperative project carried out by the respective operations and research departments of Schlumberger Well Surveying Corp., Shell Development Co. and Shell Oil Co. The primary objective of the experiment was to determine in the borehole the streaming-potential behavior of both shales and mud cakes under conditions approaching, as nearly as possible, those normally encountered in logging practice. METHODS AND EQUIPMENT WELL A Muddy- and Dakota-sandstone vie11 in the Denver basin was chosen for the experiment. Both sandstones were water-bearing and, since reservoir pressures in these sandstones are abnormally low (gradient of approximately 0.25 psi/ft), it was expected that studies of streaming potential could be conducted from low-pressure differentials (approximately 200 psi) to about 27000 psi by bailing mud from the hole, filling up and then applying wellhead pressure. The selected well encountered the Muddy sand-

By A. J. de Witte

INTRODUCTION The importance of determining dips of subsurface formations in wells, especially in wildcat wells, is self-evident and need not be enlarged upon. Various dipmeter instruments have been described in technical literature1,2,3,4 over the years. The introduction of the continuous dip-meters3,4 has made the earlier types obsolete. Continuous dipmeter logs are run by at least two different major service companies. Included as part of the service are a limited number of dip calculations—usually 10—made at different levels from the log. Very frequently this is the total result of a dip survey. It is believed that dipmeter surveys would be of considerably more advantage if geologists and engineers were able to make their own calculations from the original records. Determination of dips from the dipmeter record starts with the correlation of three log curves taken at different sides of the borehole. It cannot be over-emphasized that the quality of the results hinges primarily on this correlation. Nobody should be better qualified to correlate logs than a subsurface geologist or field engineer. The next requirement is to have an easy yet accurate way of computing the dip from the correlated points. Service companies use a mechanical device for this purpose. Directions for a graphical method were given in a recent article by B. 0. Prescotts. This paper describes a different graphical technique which, in our experience, is simpler, faster and at least as accurate. The entire manipulation is carried out on the stereonet in a number of easy moves. The paper is divided into two parts. This first part contains the introductory sections and full explanation of the geometry involved. The second part reviews the reading of data from an actual field log and summarizes the practical rules for computation of dips, the whole process being illustrated by an example. Following the outlined procedure, one could calculate a good many levels in a relatively short time, thus being able in particular to check suspected anomalies such as fault zones or unconformities in as close detail as the log will permit. GENERAL EXPOSITION OF THE METHOD Prnciple of the Dipmeter The position of a plane in space is defined by the location of three points, not on a straight line. Referring to Fig. I, if a borehole traverses a bedding plane, we can determine the strike and dip of the bed by finding three points which are not in line along this plane. Such points as A, B, and C are obtained with the dipmeter. The device consists of three electrodes (or caliper arms)1, 2, and 3 spaced at 120 angles, as schematically indicated, whose readings are separately recorded (Curves 1, 11, 111, to the right). When electrode 1 passes the boundary of the bed, Curve I will kick, etc. From these curves, we know the relative distances of points A, B, C, measured along the axis of the hole. If A is at zero, then B and C are at levels d1 and d2 up the hole,

Jan 1, 1957

By H. J. Beach, W. C. Goins

The laboratory development and field use of oil well cement compositions* with high resistance to drilling mud contamination are described. Resistance is obtained by adding a I-lb mixture composed of three parts paraformaldehyde to two parts sodium chromate tetra-hydrate for each sack of cement. This mixture neutralizes the cement-retarding properties of quebracho and other tannins, starch, sodium carboxymethylcellu-lose, Ignite, and monovalent salts of lignosulfonic acid. The retarding properties of calcium lignosulfonate are unaffected. The decontaminating mixture may be used in common cement (designated Type I by ASTM specifica-tions,' Class A by API Std. 10A2) or in a slow set slurry prepared from common cement by addition of calcium lignosulfonate. No changes in slurry viscosities or thickening times are caused by the protecting reagents. The method has been used in 185 field jobs where an improved success ratio has been obtained in plug setting. INTRODUCTION Field experience and laboratory investigations have established contamination by drilling mud as a major factor in oil well cement failures. During 1955, 12 attempts were required to set six open-hole cement plugs in the Timbalier Bay field, La. Eighteen to 30 hours elapsed between placing and testing the plugs in preparation for sidetracking operations. Considerations of rig time expense required immediate resetting where soft cement was drilled after a reasonable waiting period. Sea water drilling mud was used in each well and daily additions of thinners, usually lignites, had been required. Sodium carboxymethylcellulose had been added regularly to control fluid loss. The 50 per cent plug failures were attributed primarily to contamination by the mud. Similar experiences can be found in other fields along the Texas and Louisiana coasts where drilling muds normally contain large quantities of organic treating materials. Cement contamination was the subject of a survey by the Mid-Continent District Study Committee on Cementing Practices and Testing of Oil-Well Cements of the API.3 Data collected from member laboratories and released in Sept., 1951, reported the effects of a number of drilling mud treating chemicals on cement. The study revealed that many of the additives, notably the organic materials in relatively small quantities, had marked effects on the properties of cements tested. Severe losses in strength and erratic thickening time resulted from small additions of mud treating chemicals such as quebracho, starch, sodium carboxymethylcellulose, and lignite. The report included no recommendations of methods for overcoming the problem. One investigation of the contamination problem reported the successful use of activated charcoal in setting cement plugs after conventional slurries had failed.4,5 The investigation indicated that an optimum concentration of 5 per cent activated charcoal was effective in combating contamination from 16.7 volume per cent of treated mud. Laboratory and field muds were included in tests and contained varied quantities of ode or more of the following: quebracho, caustic, starch, lime, and calcium lignosulfonate. The function of the charcoal appears to be physical, removing the organic materials by adsorption. The method may be employed in API Class A or Class D (unretarded slow set) cements. The chemical approach presented here is based on

Jan 1, 1958

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By P. Majani, F. P. Kokesh, M. Grosmangin

Determination of the quality of cementation of casing in oil wells in the past has involved inflow and circulation tests to insure that the producing zones were adequately sealed off from the adjacent zones. Existing logging methods, such as temperature and radioactivity surveys, may detect the presence of cement behind the casing. However, the qualities of the cement (i.e., its hardness and particularly its bond to the casing) are not indicated. The new logging method described in this paper operates on the principle that the attenuation of a sonic pulse transmitted by a casing is greatly increased when that casing is bonded to an outer annulus of hard material (such as set cement) which has an appreciably smaller sonic-wave velocity than that of the casing. The down-hole tool contains a source of recurrent sound pulses which are detected by a receiver spaced a few feet from the source The amplitude of the detected casing-borne pulse is measured, and the resulting signal is transmitted to the surface where it is recorded vs depth. Since amplitude is a function of attenuation, the log is readily interpreted. Laboratory studies have shown straightforward relationship between attenuation and such variables as source-detector spacing and per cent of circumference bonded. It is shown that cement not set or not bonded to the casing has compara- tively little attenuating effect. Field examples show not only the cement top, but also the variation in cementation quality below the top. Further, the increase of bonding with time and after squeeze cementation is depicted. The detection of poor cement jobs is confirmed by production tests and by formation-test results. It is anticipated that the method will have wide application in evaluating cementation quality prior to formation testing in completions and recompletions. The analysis it affords may aid in further improving cementation techniques. INTRODUCTION The main purpose of oilwell cementing is to isolate a production zone from other undesirable zones. To investigate whether this purpose has been accomplished, several logging methods have been used such as temperature logs, radioactive tracer logs, etc. While these logs all respond to the presence of cement behind the casing, they do not indicate the degree of bonding of the cement to the casing. Early in the application of sonic logging, it was noticed that considerable attenuation of sound signals takes place in cemented pipe and is often made evident on the standard Sonic log by cycle skipping.' The development of a circuit capable of continuously recording the amplitude of the casing-borne sound signal has made possible an extensive series of laboratory and field tests, which gave the following results. The amplitude of a sound signal after it has traveled in a firmly cemented pipe is only a small fraction of that recorded by the same device in free pipe. This provides a wide spectrum of energy levels; for given local conditions, empirical values of the amplitude can be correlated with the quality of cementation. Interpretations made in this manner generally have been confirmed by production tests, circulation tests and squeeze cementation. The purposes of this paper are to give a general description of the new logging method and to present some laboratory and field results. CYCLE SKIPPING Early attempts to study the quality of the cement behind the casing were performed with a standard Sonic log, which measures the transit time At, and were based on the well known phenomenon of cycle skipping.' Cycle skipping normally is interpreted as being a manifestation of weak signals at the receivers. The log of Fig. 1 was run with the recording instrumentation adjusted to enhance cycle skipping. A mirror-image presentation was used for better visual interpretation. The transit time of sound in steel is about 58 microseconds/ft (corresponding to a velocity of 17,000 ft/ sec), and the portions of the log where this value is recorded are interpreted as zones with no cement bond. Where cycle skipping produces a higher value of At, weak signals (or a high rate of attenuation) are indicated, and a good cement bond may be present. The occurrence of cycle skipping, however, depends too much on instrument adjustment to give a uni-

By Leendert de Witte

A review is given of the principles on which recently proposed methods of electric log interpretation in shaly sands are based and of the evidence brought up in support of the theoretical derivations. It is. pointed out that the qualitative techniques suggested to date have a tendency to be too pessimistic in the prediction of the presence of commercial hydrocarbon accumulations. In the quantitative treatment, a new concept is introduced, namely that of strongly reduced activity of the double layer counter ions which are present near the negatively charged rock surfaces. This lemmu when applied to the calculation of the equilibrium concentratiotls of interstitial waters yields a set of very simple relations. The resulting expressions for electrochemical potentials across rock samples appear in satisfactory agreement with laboratory experiments. The formulae obtained for the electrical conductivity of shaly formatioris are of the same form as those arrived at empirirally by previous workers. Combination of the expres.riorls for potentia1s and conductivities gives a direct proof of the Tixier relation which states that for shaly water sands the product of apparent formation water resistivity and apparent formation factor equals the resistivity of the sand 100 per cent .saturated with formalion water and which was verified by the work of Wyllie and Perkins and their co-workers. The relations for the resistivities and spontaneous porer11inI.s have been extended to the case of hydrocarbon hearing shaly formations, thus laying a formal basis for the quantitative interpretation of electric logs in shaly oil sands. INTRODUCTION The presence of disseminated clays in porous rocks saturated with electrolytic solutions has a strong influence on the transference of ions taking place under electrical or chemical potential gradients. Both the electrochemical emf's in evidence on the SP curves of electric logs and the electrical conductivity measured on resistivity logs arc directly dependent on the ionic transference in the interstitial waters of the formations traversed by boreholes. A large number of researches have been carried out on the nature and magnitude of the effects of clays on ionic transference. The most recent of these have been described in papers by McCardell and Winsauer,1 2 Wyllie and Southwick,3 poupon, Loy, and Tixier,4 and by Perkins et al.5 Most of these authors consider the effects of the clays as due to the fixed negative charges on the clay lattice. These charges cause the formation of diffuse surface layers with a high concentration of positive ions. The internal solution of the shaly reservoir rock has therefore a different ionic composition and concentration than the electrolyte with which it is in equilibrium (connate water produced from the formation or mud filtrate by which the formation is invaded). To calculate the equilibrium concentration of the internal solution, use is made of the Donnan6 relation, which states that the mean ionic activities of the internal solution and of the external electrolyte must be equal. From this and the

Jan 1, 1956

By G. R. Pickett

Examples are presented which show that the velocity~ amplitude, attenuation and apparent frequency of several acoustic waves can be recorded in the borehole. Examination of such recordings, termed "character" logs, indicates that the wave types observed include a refracted compressional wave and a wave which travels with formation shear velocity. Laboratory data are used to show that compressional and shear wave velocities are dependent on porosity, effective stress and lithology; but that the change in reciprocal velocity per unit change in porosity is larger for shear waves than for compressional waves. We, therefore, conclude that. the accuracy of porosity determinations can sometimes be improved by use of shear wave velocities, provided that the shear wave amplitudes are large enough to delineate the shear arrival from the preceding compressional arrival on the character log. Borehole data are presented which show that the difference between shear wave and compressional wave reciprocal velocities can be used to predict porosities. This is a refinement which may allow the prediction of porosities from single-receiver acoustic logs without introduction of errors from borehole fluid traveltimes. Laboratory and field data are presented to show that the relationship between compressional and shear wave velocities can be used to indicate lithology. An example is presented to show that fractures usually cause a greater reduction in borehole shear wave amplitudes than in compressional wave amplitudes, an effect which may offer a more reliable means of detecting fractures. The complexity of the borehole acoustic wave train can rake presently available cement bond logs highly sensitive to the gate and bias settings used. The character log offers a means to circumvent possible misinterpretations by recording all amplitudes, from which the interpreter can select the appropriate data for evaluating the cement bond. Character logs may also be used as a quality control for open-hole transit-time logs when existence of small compressional wave amplitudes interferes with the proper functioning of bias-controlled timing devices. Evaluation of the potential uses of character log data is not complete; but a character log presented in a form convenient for routine use would be a desirable addition to currently available logs. To summarize, possible applications for such a log in formation evaluation include the following (1) quality control of transit-time logs, (2) refinement of porosity predictions, (3) determination of lithology, (4) improvement of fracture detection and (5) improvement of cement bond evaluation. Suggestions are made regarding the requirements for a suficient but practical character log for routine use. INTRODUCTION Acoustic logs have become a widely used porosity tool in formation evaluation. In addition, there is a growing application of acoustic logs in cement bond evaluation and fracture detection. These applications have mainly involved the use of logs of first-arrival transit times and amplitudes and have not included detailed studies of the complete signal. The purpose of this paper is to show that significant benefits in formation evaluation can be gained by a more complete use of the acoustic wave train generated in the borehole by an acoustic logging tool. We hope that this discussion will also stimulate further development of logs suitable for routine use so that these benefits may be realized. Examples of acoustic wave train logs, termed "character" logs, are presented to show that several identifiable acoustic waves are present in the borehole. The measurable characteristics of these acoustic waves and some of their relations to formation properties of interest are also discussed. The more obvious potential uses of character logs are listed, and some suggestions are made regarding the requirements for a sufficient but practical character log for routine use. CHARACTER LOGS Some 10 years ago, Vogel' and Summers and Broding' noted that the signals received uphole from an acoustic logging tool located in a borehole had a number of interesting characteristics. The logging tool consisted of two or more pressure transducers spaced on an acoustically insulated body (Fig. la). One of the pressure transducers was used as a transmitter to generate pressure waves in the borehole fluid. The other transducer served as a receiver to detect any pressure waves reaching it in the borehole. The receiver then converted these pressure waves to electrical signals which were transmitted to the surface and displayed on an oscilloscope as a record of time vs receiver-signal amplitude. Fig. lb is a schematic representation of a typical record. The interesting characteristics seen in the earlier' and subsequent experiments were (1)

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with