Search Documents

By Stuart M. Lipofsky, Norm Hutchins

The Metropolitan Water District of Southern California has undertaken the Lake Mathews Outlet Facilities project to replace the existing outlet facilities. In the late1990s, consulting engineers for the District determined that the Lake Mathews Outlet Facilities were susceptible to a catastrophic failure during a seismic event. To ensure a reliable supply of water to Metropolitan’s customers in the Los Angeles area, the District decided to construct new outlet facilities. This Project consists of excavating a large diameter junction shaft, a 6.10 m (20 ft.) horseshoe tunnel, three short 4.88 m(16 ft.) horseshoe bypass tunnels, and a large excavation within a cofferdam that were all driven in difficult rock conditions. Additionally, a new concrete outlet tower was constructed and connected to the existing tunnel by the new bypass tunnels and through the junction shaft. The J.F. Shea Co., Inc. of Walnut, California, is currently finishing the construction of the Lake Mathews Outlet Facilities Project for Metropolitan. The large diameter junction shaft is 50.60 m (166 ft.) deep, excavated 16.15 m (52 ft.) in diameter and lined with a61 cm (2´-0?) thick steel reinforced concrete lining to a finished diameter of 14.63 m (48ft.). The shaft was excavated full face with one stationary shaft three-boom jumbo, modified for the large diameter. The shaft also consists of four sets of gate guides extruding from the shaft wall towards the center of the shaft that provide the ability to operate up to four mechanical gates at any time, to open or close each tunnel. This paper will present the junction shaft excavation and concrete construction techniques, including the innovative slip form method utilized to construct the junction shaft.

Jan 1, 2003

By R. Schuerch, C. Cimiotti, G. Anagnostou, J. Nickerson, P. Perazzelli

"This paper presents experiences gained from the construction of the Lake Mead Intake No. 3 project. The 4.7 km long tunnel was excavated with a hybrid TBM (able to operate in both closed and open mode). The tunnel crossed metamorphic and sedimentary rocks under a hydrostatic pressure of about 14 bar. During the excavation of the tunnel the TBM encountered difficult ground conditions caused by a combination of high water pressure, poor ground quality and locally low depth of cover. The adverse conditions required the TBM to be driven in closed mode at very high support pressures (10 – 15 bar) for approximately 60% of the tunnel length. The paper summarizes the main problems encountered during TBM excavation and analyzes the evolution of the TBM parameters over the entire tunnel length. INTRODUCTION The Lake Mead Intake No. 3 project is located approximately 30 km away from the city of Las Vegas in Nevada, USA. The project consists of the construction of a deeper third intake for the biggest reservoir in the United States, which is formed by the Hoover Dam. The construction of the new intake was required due to the constant drawdown of the lake level (more than 40 m in the past 20 years) and the consequent risk that the shallower intakes 1 & 2 may run dry. The project included the fabrication and positioning on the lake bottom of an intake riser, the excavation and lining of a 185 m deep shaft and construction of a 4.7 km long tunnel. One peculiarity of the project is that the water table is located about 140 m above the tunnel elevation (i.e. corresponding to a hydrostatic pressure of 14 bar at the current lake level). The tunnel was constructed using a tunnel boring machine (TBM) able to operate in both open and closed mode (Mc Donald & Burger, 2009). The present paper focuses on the TBM tunneling experience gained from the Lake Mead Intake No. 3 tunnel. The TBM excavation started on December 27, 2011 and finished on December 10, 2014 with the breakthrough to the intake structure at the bottom of Lake Mead. GEOLOGICAL CONDITIONS The assessment of the ground conditions encountered during construction was mainly based upon qualitative descriptions of the tunnel face conditions (during open mode operations) and analysis of the extracted muck (during closed mode operations)."

Jan 1, 2016

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By J. Chia, M. H. Kobler, J. Cheung, M. J. Robison

INTRODUCTION The Lake Merced Transport is being constructed as part of San Francisco's Clean Water Program. The Clean Water Program, which began in the early 1970's, is designed to control wet weather, storm sewage overflows into the Pacific Ocean and San Francisco Bay. To accomplish this goal, a system of large underground storage and transport facilities, pump stations, modernized treatment plants, and outfalls is being built. By 1991, eighty percent of the system had been completed and was in operation. One of the remaining projects for the Clean Water Program is the Lake Merced Transport. The Lake Merced Transport is located in the extreme southwestern portion of San Francisco, as shown in Figure 1, Project Location. The transport will convey dry weather flow from the existing Lake Merced Pump Station to the Westside Pump Station. During wet weather, the transport will fill with sewage and runoff, with a storage capacity of 36 million liters. The Lake Merced Transport was expected to be excavated entirely within the Colma Formation, an alluvial deposit consisting of weakly cemented sand. Once excavation of the access portal at the Sloat/Great Highway parking lot began, it became evident that a portion of the tunnel would be excavated through beach/dune sand. Based upon the expectations of the Geotechnical Design Summary Report (GDSR), encountering beach/

Jan 1, 1993

By Lee W. Abramson, Mee Shing Owyang

The Lake Merced Transport tunnel is 18 feet in diameter and 1.6 miles long constructed within dune sands, beach sands, and the Colma Sand Formation. It runs beneath highway right-of-way from an existing pump station near the shore of Lake Merced to a point near the Pacific Ocean, where it will connect with the existing transport/storage tunnel. The final tunnel lining was originally designed as a cast-in-place concrete lining to be constructed within steel ribs and wooden lagging initial support. The contractor opted to use a precast concrete segmental initial lining thus requiring a redesign of the final lining. The redesigned lining incorporates composite action from the initial lining thereby eliminating the need for outer steel reinforcement. A computer model was used for analyses which included operating conditions, ground and construction loads, and possible effects of liquefaction and earthquakes.

Jan 1, 1993

By R. J. Allan

"CANADA HAS A GREATER LAKE AREA than any other country. Discountin the Great Lakes, this fresh-water area, mainly in the Canadian Shield, is listed as approximately 300,000 sq. mi. Densities of lakes range up to 7,500 in a 5,294-sq. mi. area of the Shield, southwest of Reindeer Lake, Saskatchewan. Five areas chosen randomly from the Shield (Figure 1) contained sufficient lakes to provide samples at a density of at least one per 10 sq. mi. Regional geochemical surveys in the Appalachian area (Nova Scotia, Boyle et al., 1958; New Brunswick, Boyle et al., 1966) and in the Cordilleran area (Yukon, Gleeson, 1965) of Canada and in many other areas of the world have relied heavily on analyses of stream sediments. These surveys show that sampling of material related to the drainage system reflects the over-all trace element content of the rocks and surficial deposits in the drainage basin. In the Shield, the classic types of dendritic (and other) stream systems found elsewhere in the world are very rare. However, impeded and disorganized stream systems that abound with lakes can provide the exploration geochemist with an ideal composite drainage system sample in the form of lake sediment. This paper attempts to demonstrate the feasibility of, and review the theory and problems involved in, the use of lake sediment as a regional geochemical exploration medium. Most of the references to field examples are taken from a regional survey using lake bottom sediment as the sample medium over 1,500 sq. mi of the Coppermine basalt group and adjacent rocks (Figure 2). During this regional survey, detailed sampling of several lakes was carried out and the results are referred to at appropriate places in the text."

Jan 1, 1971

By W. T. Robson

LAKE Shore Mines, Limited, with property at Kirkland. Lake, Ontario, was incorporated m 1914 and commenced product10n m March, 1918, with an initial capacity of about 60 tons per day. Since that time a gradual expansion has taken place until a present capacity of approximately 2,300 tons per day has been reached, giving a total annual gold production valued at approximately $16,000,000. At the time of incorporation of the Company, the Lake Shore property consisted of four mineral claims and four fractions, totalling 171.05 acres. In 1934, four claims belonging to the Minaker Kirkland Gold Mines, Limited, were acquired and a controlling interest purchased in the Kirkland Hudson Bay Gold Mines, Limited. Both these properties adjoin the Lake Shore claims on the south. From the accompanying compilation of the world's largest gold mines for 1934 (1), it will be seen that, while Lake Shore holds sixth position in respect to the number of ounces produced, there are twenty-five gold mines which treat a greater tonnage of ore. This is an indication of probably the most unusual feature of the Kirkland Lake deposits, namely, the high aver-age tenor of the ores. coupled with the comparatively large tonnages available.

Jan 1, 1936

By F. R. Jones, B. W. Taylor, A. R. MacPherson, L. J. Lamb

"The Lake St. Joseph Iron Deposit is in Northwestern Ontario. Exploration to date by Steep Rock Iron Mines Limited has indicated an ore reserve of 683 million long tons. Metallurgical investigations have proved that suitable oxide pellets and/or superconcentrates can be economically produced from this ore. Studies of the Lake St. Joseph iron ore deposits have covered the period 1956-71, and have embodied applications of the improvement in mining and processing technology over this period. Market demand in the early 1960's for high-grade oxide pellets as a replacement for natural iron ores for the blast furnace first drew attention to the potential of the Lake St. Joseph deposit. The current market trend toward utilization of sponge iron to replace steel scrap as feed to electric furnaces and cupolas now suggests that the deposit can better be exploited as a prime source of superconcentrates."

Jan 1, 1972

By AIME AIME

ADDRESSING the Ohio Section at a recent meeting in Columbus, Ohio, R. C. Allen, executive vice-president for Oglebay, Norton & Co., Cleveland, spoke on "The Iron-Ore Industry of the Lake Superior Region in Prosperity and Depression." The speaker considered this region in connection with the problem of national security. This is the age of minerals; progress depends on them; and next to agriculture, the mineral industry is of prime importance. The United States has no shortage of minerals rather an over-supply; but many mines have been and are being exhausted. The shifting of the sources of supplies of minerals so important as copper, petroleum, and iron to other countries would create internal strains and affect international relations. There will be no early decline of ore mining in the Lake Superior region unless it is forced by unwise public policies. Iron ore is industrial strength and self-sufficiency. A study of economic geography is important for statesmen and mining men, because the minerals essential for peace and war are haphazardly or irregularly distributed throughout the world. Of these minerals, 75 per cent are owned by 10 per cent of the population, mainly peoples of Anglo-Saxon origin.

Jan 1, 1934

Lake Superior Iron Ore Association, 3100 East 45th St , Cleveland, Ohio W L Tinker, Secretary This Association does not issue scientific technical bulletins, strictly speaking, but statements, etc , are published containing information of interest to mining engineers and geologists To show the type of information published, mention may be made of material issued in 1931: 1 Directory of mine operators and statistical data. 2 A bulletin, Distribution of Lake Superior iron ores, also Eastern and foreign ore 3 A booklet, Analyses of Lake Superior iron ores, season 1931 These publications, or information on others may be had by addressing the above

Jan 1, 1933

By Alexander N. Winchell

"The iron ores of the Lake Superior region are found almost exclusively in rocks of Huronian age, the only exception of importance being in the Vermilion district. It may be estimated that about 95 per cent of the ores thus far mined have been obtained from Huronian rocks. Although these ores come from rocks of varying age and slightly varying type, they have many features in common, and therefore may readily be described together.The iron formations of the Lake Superior region consist essentially of interbanded layers of mixtures in widely varying proportions of silica and iron oxide, and are called taconite, ferruginous chert, or jaspilite. They vary considerably in hard¬ness and color, depending upon the tenor of silica and the history of the rock. Local phases of the iron bearing formation consist of cherty iron carbonates, greenalite or ferrous silicate, rocks, amphibole-magnetite masses, cherts and slates, and pyritic quartz rocks. The average iron content of all the original phases of the iron bearing formations, excluding interbedded slates, is about 25 per cent, while the average iron content for all portions of the formation, whether in the original condition or not, is about 38 per cent. It is believed that this difference is due essen¬tially to the removal of silica in solution from the. primary phases, and, of course, such removal of silica has in many cases produced material now used as iron ore, since it contains con¬siderably more than 38 per cent of iron."

Jan 1, 1920

IN accordance with a programme arranged by a committee of the Institute, consisting of Mr. William P. Shinn, of St. Louis, chairman, and Mr. Joseph D. Weeks, of Pittsburgh, secretary, the member's of the Institute, with their ladies and invited guests, assembled in Chicago on Sunday morning, August 22d. A special train, provided by the Chicago and Northwestern Railway,. left Chicago on Monday morning at 7.50 o'clock, and conveyed the party to Marquette, arriving at 9 o'clock P.M. Here the steamer Northern Queen, which had been chartered by the committee for the accommodation of the Institute, was in waiting, and the members and ladies at once took up their quarters on the boat. EXCURSIONS IN THE MARQUETTE IRON REGION. Local Committee. EXECUTIVE. -J. C. Morse, chairman; C. Y. Osburn, secretary ; D. F. Wadsworth, treasurer; C. H. Hall, H. Merry. RECEPTION.-S. P. Ely, J. P. Pendill, E. Breitung, W. F. Swift, A. P. Swineford, J. C. Fowle, C. G. Griffey. TRANSPORTATION.-Samuel Schoch, D. Morgan, D. H.. Merritt, J. Pickands. FINANCE.-Peter White, A. W. Maitland, W D. Rees, E. R. Hall. EXCURSIONS.-W. E. Dickinson, H. A. Burt, A.. Kidder, C. E. Wright. REFRESHMENTS.-J. Q. Adams, H. H. Stafford, Joseph Kirkpatrick, D. H. Bacon. On Tuesday the iron mines in the vicinity of Negaunee and Ishpeming were visited, transportation being provided by special trains on the Marquette, Houghton and Ontonagon Railroad. In the morning the McComber, South Jackson, and Jackson mines were inspected, and in the afternoon the Cleveland, New York, Lake Superior, and Barnum mines. Dinner was provided at Negaunee, and gracefully served by, the ladies of the town. In the evening the first session of the Institute was held in the saloon of the steamer. The President, William P. Shinn, of St. Louis, congratulated the Institute on the happy consummation of the wishes of its members to have a meeting on Lake Superior. After tedious and baffling negotiations arrangements had been com-

Jan 1, 1881

Jan 1, 1881

Jan 1, 1922

Jan 1, 1898

Jan 1, 1905

The Lake Superior Mining Institute, Ishpeming, Mich. A. J. Yungbluth, Secretary. An Annual Volume of Proceedings, carrying papers presented during the year, has been published since 1S83, with the exception of the years 1S97, 1899, 1907, 1916, 1918, 1919, 1920, 1921, 1924 and 1927. No meetings were held during those years and conse-

Jan 1, 1933

By Courtenay DeKalb

The accompanying illustrations, Figs. 1 to 6, from plans drawn by Mr. T. L. Knapp, a student in the Missouri School of Mines, show a type of furnace designed by the writer, which possesses some peculiarities intended to meet the necessities of laboratory-instruction in that institution. The object aimed at was the construction of a simple, inexpensive furnace, suitable for the distillation of zinc from its ores, and using only a single retort. This limitation imposed the chief difficulty, owing to the necessity of obtaining a high degree of heat concentra ted upon the retort. This is accomplished by the peculiar curve of the arch, which consists of arcs of seven distinct ellipses, one focus of each of which lies within the area occupied by the retort. Thus the reflected heat would necessarily be thrown mainly where most needed, namely, on the retort. Conservation of heat is provided for by a return-flue through the hollow arch, and by a sand bottom under the fire-brick hearth. Four openings lead back from the laboratory, or heating-chamber in this instance, to the arch-flue; and three openings lead from the arch-flue to a large horizontal flue, from which a down-take conducts the gases to the stack. The fire box, it dl be observed, is deep, thus producing much CO during the combustion of the coal. The further combustion of this CO may be accomplished by the admission of air through the hollow fire-bridge, thus producing a higher flametemperature surrounding the retort. Provision is also made for removing the retort and the portion of the wall supporting it and the condenser, leaving a high arch, into which a door-frame may be inserted; the space above being temporarily bricked in. By this alteration, which may be quickly and easily made, the furnace may be converted into a reverberatory, suitable for treating small charges such as

Jan 1, 1898

By P. Barnes

The object of this paper is to make a brief comparison of the outlines of several forms of ports for steel-melting turnaces, in reference chiefly to the proper mixture; of the gas and air, and to the direction in which the flame is thrown down into the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M, Pernot, of St Chamond, France. This is used with the dome roof preferred by him fur the revolving bottom that bears his name. From No. 1 has been derived No. 2. This is shown on the plans of Mr. A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched roof of nearly the ordinary form, instead of over the top of the roof, as with the dome of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or " washing "-—to use the briefer French term. in this the gas and air come into contact in broad sheets one above the other, Fig. 5 shows the form used by Messrs. Richmond & Potts

Jan 1, 1881