Search Documents

By Jason Morrison

The Norwegian Lake Tap Method was successfully used to tap into the side of Lake Dorothy 36.5 m (120') below the lake surface. The lake tap allows water to flowinto an access tunnel from the lake lowering the water elevation below its natural out-fall. When the lake reaches a predetermined elevation below the outfall, a 1.5 m (60?) valve in the tunnel will be shut and discharge from Lake Dorothy will stop temporarily allowing construction of a dam located 2.9 km (1.8 miles) downstream at Bart Lake. The lake tap and tunnel were one phase of the $64 million Lake Dorothy Hydroelectric Project, owned and operated by Alaska Electric Light & Power Company (AEL&P), a private utility located in Juneau, AK. The Lake Dorothy portal site and tunnel are located approximately 25.7 km (16 miles) southeast of Juneau, AK, in the remote Tongass National Forest at an elevation of 701 m (2,300') above sea level in the mountains above the Taku Inlet. Thirty degree snow covered mountainsides and limited access by helicopter were just two of the many factors which challenged this unique project. The lake tap and tunnel development consisted of 250 m (820') of horizontal tun-nel, averaging 3.6 m x 3.6 m (12' × 12'), excavated using conventional drill and blast methods in highly competent Granodiorite and Tonalite rock, placement of one 3.9 m (13') long concrete plug, or bulkhead, located at the tunnel midpoint, and one 3 m (10') diameter lake tap into the side of Lake Dorothy. This paper will provide an analysis of the logistical and engineering challenges involved in the development of one of only a handful of lake taps in North America. AEL&P and contractor J. S. Redpath Corporation worked together to complete this critical project phase safely and on schedule, in a location accessible only by helicopter and plagued by constantly changing, harsh weather conditions. A strict schedule had to be maintained to ensure the timely operation of the downstream dam and power plant.

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By J. E. Hawley

"The zinc-lead deposit of the Lake Geneva Mining Company is on lot 7, con. VI, Hess township, Sudbury district, Ontario, about 10 miles northwest of the northern rim of the Sudbury Basin. Though a relatively small deposit, it shows some rather interesting relations to cross-cutting, pre-ore, quartz diabase dykes, which merit description.The deposit was discovered in October 1924 by J. H. Collins beneath iron-stained drift and oxidized sulphides. This proved to be the northwestern extremity of the orebody, the remainder of which extends southeast below swampy ground. Exploration began in 1927. In 1928 a vertical shaft was sunk to 250 feet and a level established at 235 feet. Later the shaft was deepened to 400 feet and new levels opened at 315 and 375 feet. In 1943 an inclined winze was sunk below the vein from the 315-foot level to a vertical depth of 640 feet, and two additional levels were opened at 525 and 615 feet respectively.The geology of the area has been described by T. T. Quirke (1), F. F. Osborne (2), F. J. Alcock (3), and Ralph Tuck (4). Private reports have also been made by Carl Tolman, J. E. Gill, and K. W. Fritzsche. Tuck's paper, covering the work completed to 1930, gives a detailed account of the character of the ore and enclosing rocks.Up to May 1944, when the property was closed, all ore above the 375-foot level and a small tonnage from below this elevation had been removed. Ore mined from 1941 to 1944 yielded the following:"

Jan 1, 1954

THE members arrived at Ticonderoga, N. Y., at noon, Tuesday, October 15th, and were received by Mr. Cyrus Butler, Chairman of the Local Committee of Arrangements. During the afternoon the works of the American Graphite Company and the Horicon Iron Company were visited under the guidance of Mr. Butler, President of both companies, and of Mr. William Hooper, Superintendent. An excursion was then made, in carriages, to old Fort Ticonderoga, on Lake Champlain, after which the party were driven to the Rogers Rock Hotel, on Lake George. The first session of the Institute was held in the parlor of time hotel on Tuesday evening. Mr. Eckley B. Coxe, President of the Institute, opened the proceedings with the following address: I shall ask your attention, this evening, to a few reflections upon the subject of mining engineering as a profession in the United States, its past, its present, and its future, and its duties and oppor¬tunities with reference to the proper development of our great min¬eral resources. Thirty years ago, there were scarcely any mining engineers in this country, and but few in England, and there were no institutions where young men could be educated for the profession in the Eng¬lish language. France and Germany have been able for about a century to boast of mining schools of a high character, that number among their graduates such men as Humboldt, Weisbach, Rittinger, Combes, and Gruner. Of the few we then had worthy of the name of "mining engi¬neer," some had studied in the continental academies, and others were graduates in the school of practical experience, and had learned their profession in mines and smelting-works. Their work con¬sisted principally in making surveys and maps of mines and mining properties, geological reports, and analyses of ores ; but the mining engineer whom we often meet with now, who has studied chemistry, physics, mineralogy, geology, mechanics, and drawing; who is more or less familiar with machinery and its construction, and with the practical management of mines or smelting-works, and who is an expert in some one branch of his profession, would have been very difficult if not impossible to find in the United States. The induce¬ments held out to ambitious and talented young men to enter the

Jan 1, 1879

Jan 1, 1879

By Charles B. Dudley

While working, during the summer of 1877, upon the "Chemical composition and Physical Properties of Steel Rails," the results of which are given in my report with this title, I was struck with the surprising wear which some of the rails, which would ordinarily be called soft rails, had endured. At that time I knew of no chemical measure of softness except low carbon, and I found that a numher of rails with low carbon had endured as high or higher tonnage, with apparently as little loss of metal by wear, as those with higher carbon. My own work on steel rails that summer did not embrace any definite experiments as to the amount of metal worn off the rail per million tons which had passed aver it; and so I could get no more definite answer from that work, to the question at the head of this paper, than was given by comparing the appearance of the worn section of the rail with its tonnage. This comparison, however, served to arouse in my mind the query, whether the commonly received opinion as to the relation between the hardness and wearing power of steel is correct, as applied to steel rails. This opinion, if I am right, is: the harder the steel, the better will be the wear, and the limit of hardness is simply one of safety; hard, brittle steel being, of course, more liable to break than soft, tough steel. The query, although aroused, did not bear any immediate fruit, and, as will be evident to any one reading it, the report above referred to was written with the commonly received opinion in mind. Since that time I hare collected a little information upon this subject, which I should be glad to submit to the Institute, if for no other purpose, for the sake of arousing attention, and directing study to the question of hardness versus wear in steel rails. Before making known this information, howevcr, permit me a few words in reference to hardness. How shall we measure the hardness of steel ? Of the various ways of getting indications as to the hardness of steel, which are known, three mill serve our present purpose. These are: 1st. High carbon. It is generally agreed, I think, that at least within proper limits, the greater the amount of combined carbon in a piece of steel, the harder the steel, and I need not do

Jan 1, 1879

By Thomas M. Drown

In the course of some experiments on the analysis of pig iron, I heated, in a platinum crucible, some borings of a graphitic pig iron with sodium carbonate. When the crucible was at a full red heat and the carbonate was thoroughly fused, I noticed a lively ebullition of the mass, and an escape of gas, which burned on the surface. On investigation this gas proved to be carbonic oxide, and on examining the borings in the bottom of the crucible after an hour or two, they were found to be perfectly malleable, although unchanged in general form and appearance. Analysis showed that the carbon was completely removed. I then repeated the experiment, to ascertain whether the silicon and phosphorus were affected, and found that these elements too were largely removed, and could be .found in the fused mass as alkaline silicates and phosphates. In order to ascertain whether the removal of the silicon and phosphorus was merely a surface action or whether the reaction really extended into the mass of the iron, I tried the following experiments : A number of bars of pig iron were cast about one foot long and planed down 'accurately to one inch section. These were immersed in a large wrought-iron pot full of molteu sodium carbonate made by fusiug the commercial bicarbonate of soda. Through the kindness of Mr. Frank Firmstone, Superintendent of the Glendon Iron Works, Easton, I was enabled to keep this pot at a reasonably constant high temperature for a long time in one of the hot-blast ovens. One of the bars was removed from the pot every twenty-four or forty-eight hours, according to the rapidity of the action, and after cooling mas broken and the fracture examined. The change from pig iron to malleable iron was progressively inwards and always sharp and easily recognized, the rate of progression being in a decreasing ratio with the time. The temperature of the oven had evidently

Jan 1, 1879

By John M. Hartman

The high temperature of the blast of modern furnaces renders it desirable that the pipe conveying the blast into the furnace crucible shall transmit and radiate as little heat as possible. To accomplish this, the pipe shown in the accompanying sketch was devised and patented. It consists of a slide-valve, leg-pipe, and belly-pipe, which are held together and to the tuyere by a system of levers and links. The slide-valve is superior to the old throttle-valve. The legpipe is formed of two thicknesses of wrought-iron pipe, with a space of half an inch filled in with clay and brick. The belly-pipe is made in the same way as the leg-pipe, and terminates in a globe face to suit the tuyere. The quarter turn is made extra thick, of cast iron, and the cap on the end is lined with clay also. The catches, A, B, C, are merely for convenience in putting the pipe together. The joints D and E are globe faces, and allow the pipe to adjust itself to any angle. The eye-piece is made of violet glass, which cuts off the glare from the bright coals in the furnace and allows a close examination of the interior, so that any water dropping or vapor can be detected. The glass does not become coated with dirt, like mica. Since good running of furnaces is shown by a bright tuyere, it is necessary to have a good eye-piece to examine them. To detach the pipe, a man lifts the weights, the side rods are then slipped off the bell crank under the quarter turn, the link under the belly-pipe is unhooked, and the pipe carried away. The same process is reversed to put the pipe together. The nozzle is changed by taking off the cap, G, drawing the nozzle through the belly-pipe, and inserting another. In this way the change can be made quickly, without taking down the pipe. On the old tuyere pipe bolts with brass nuts were used, which burned up and gave trouble. In other cases key-bolts were used, making it difficult to adjust the pipe. Bolts make too rigid a joint, and there is no provision for movement from contraction or expansion. As the temperature of the blast increases there is more expansion, and where rigid joints are

Jan 1, 1879

By R. H. Thurston

Jan 1, 1879

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879

By Ellis Clark

The greater portion of the brown ore in the vicinity of Easton, along the north slope of the Lehigh Mountain or Durham range of hills, is obtained from mines instead of from open cuts or quarries, as is the case in the ore-beds in the western part of Northampton County, in Lehigh County, and in Berks County. The reasons for this method of procedure are various, and the principal causes of the shaft and regular mine system of working being adopted instead of the open air cuts, are: First, the large amount of stripping that would be necessary, as the richer and more valuable portions of the ore do not appear to be found as near the surface as those in other portions of the Kittatinny valley; second, the occurrence of the ore in regular beds, interstratified with the clay, and, to a less extent, in pockets or erratic deposits, as is the case in the mines of Lehigh County; and third, on account of many of the mines being situated at the immediate base of the Lehigh Mountain, where the surface water would be in such large quantities as to be with difficulty handled, and where the subsequent caving in of the sides of the open cut would be almost certain to expose the gneiss rock, which is water-bearing, the large quantities of water coming from which would probably drown out the ore-bed. Shafts, and a regular system of gangways and mining are therefore required by the configuration of the surface, the depth of the deposits and their geological structure. The ordinary size of the shafts is about four feet square, but where an extensive plant of pumping machinery is required the size may be increased to eight feet by six, with two compartments for the hoisting and pump-shaft respectively. A man-way, consisting of ladders with rests at intervals of twenty or thirty feet, is comprised in the pump-shaft, the wire rope being used for purposes of ascent and descent only in exceptional cases, on account of accidents which

Jan 1, 1879

By Henry S. Drinker

The Butler Mine property is situated in the vicinity of Pittston, in the Wyoming coal-field of Pennsylvania. The coal has been ' worked out from the fourteen-foot or Baltimore vein for a number of years on part of the tract, the old chambers remaining open as when originally abandoned. This vein outcrops on the Butler prop erty, and is nowhere more than sixty feet below the surface of the ground on the line of the cut-off to be described. Above the four teen-foot vein and about, say midway, between it and the surface of the ground, there is another small vein or rider of coal, about twelve inches in thickness. The rock between the two veins is a carbon aceous slate, about twenty-five feet in thickness. Above the smaller vein is a bed of sandstone, varying in thickness, but generally not less than from eight to ten feet. This sandstone is also carbonaceous, but the proportion of carbon is much less than in the slate below. Both rocks have been analyzed, and before the next Institute meet ing, the writer hopes to be able to furnish the exact proportions. The sandstone is overlaid with debris up to the surface of the ground. Some time during the spring of 1876, it was found that the coal left in the worked-out mine had been set on fire, and that the fire was gradually spreading. Inquiry developed the fact that the fire had originally been started by a woman, who had taken up her abode in an old tunnel leading into the workings. Owing to some delay in the early attempts made to extinguish the fire, it finally gained such headway that no ordinary means were found to be effectual. Finally, Mr. C. F. Conrad, civil and mining engineer, of Pittston, Penna., was called in as consulting engineer. He advised the making of a thorough cut through such portion of the old workings as had not been reached by the fire. It was found by survey that this cut could be limited to a length of about one thousand two hundred feet, as the vein faulted on both sides, and that the greatest depth of the cut would be about sixty feet. Subsequently it was decided to tunnel part of the way, thus saving the deepest portion of the cut. In 1856-7, there occurred a fire in the same mine. Two stone walls in V-shape running from the apex of the V towards the out crop, were built to cot the fire 06 and these walls were carried as far as the vein had at that time been worked. After the walls were finished

Jan 1, 1879

By Charles B. Dudley

In the spring of 1877, the Pennsylvania Railroad Company became so dissatisfied with the average life and wear of the steel rails it was then able to procure, that it determined to make an invest,igation into the chemical composition and physical properties of steel rails, with a view, first, to answering the question why one steel rail has to be removed from the track after, perhaps, eight months' service, while another lasts ten years; and, secondly, if this investigation succeeded in throwing light on this important subject, to use this information in securing better rails in the future. The results

Jan 1, 1879

By John Birkinbine

The favor with which the members of the Institute received Mr. Fernow's paper upon the use of charbon roux in the manufacture of iron has encouraged me to present this paper, in the hope of having the discussion upon the manufacture and use of the oldest and undoubtedly the best fuel for producing pig iron continued. Owing to the advances made in employing anthracite coal, bituminous coal, or coke, or mixtures of them, we are apt to forget how much of our present development is due to the pioneers in iron manufacture and the fuel which they employed in the production of pig iron. In Mr. Swank's last compilation of the iron and steel works of the United States, the furnace capacity of the country is given as 5,868,000 tons, of which 1,000,000 tons can be made in the 264 charcoal furnaces. In other words, over one-third of the furnaces now in existence use charcoal for fuel, and produce more than onesixth of the iron made. If to this is added the 130,000 tons of blooms and billets turned out by the 122 forges and bloomaries, the importance of the charcoal industries will be appreciated.

Jan 1, 1879

By P. Barnes

Several statements have been made to the Institute, somewhat detached from each other, as to the cost of some parts of these works, but they have not included any extended description of the buildings or machinery. The general plan of the work connected with the water supply differs, in some important details, from that which has been common either in the Pittsburgh district or elsewhere, and a somewhat extended description may be of interest to the Institute, in connection with a note of the cost of the work. The plan as a whole, and nearly all the important details, were developed by Mr. William P. Shinn, C.E., the general manager of the Company. The immediate and responsible charge of the work was in the hands of Mr. John C. Lewis, C.E., to whom had been committed all the work of this general description, including the laying out of the whole of the foundations, the erection of the buildings, and the grading and laying down of the entire railroad system. The continuous operation of the machinery and other fixtures of these waterworks, for more than three years, has fully demonstrated the correctness and econonly of the plan adopted. No casualties of any moment have befallen the apparatus, and no improvements have been suggested as important except that the gate at the river end of the conduit should have been made more completely water-tight, so that the whole length of the conduit could be pumped out dry without resort to any temporary dam in the conduit itself. In general terms the works of the Edgar Thomson Company are situated on a plateau, about 52 feet above the low-water level of the Monongahela River, and about 2000 feet from its bank. The site of the works is bordered on one side by Turtle Creek, a small stream which drains a considerable area of coal mining territory. This creek is about 100 feet from the group of buildings which have been erected, but it flows into the Monongahela River at a point, about 1200 feet further up than that selected for the entrance to the waterworks conduit. It was ascertained by analysis that the water in the creek contains an important percentage of sulphate of lime, while the water of the river is of unusual purity, in respect of any salts

Jan 1, 1879

By D. Torrey

Considering the two great interests of to-day, in iron upon the one hand and steel upon the other, and recognizing with measurable distinctness the peculiar fitness of each for special services to which they are applied, the proposition to unite the two metals in combination, to bring into simultaneous use the peculiar advantages which each offers, has great attractions. The limited success which has been attained by trying to bring about such combinations of the two metals through the use of fluxes in welding, has led to the general adoption of the opinion that an effective union of the two metals is impracticable, or to the view that if practicable it would have but limited commercial value. Such opinions are, I think, premature and erroneous, and having gained some knowledge of the character and value of the "Wheeler process" for welding iron and steel without the use of fluxes, I submit the following observations and opinions of the matter for your information, with the hope of eliciting such a discussion of the subject as it may require. The principle of the invention is to bring the two metals simultaneously to a welding heat in one pile, and then to manipulate it.

Jan 1, 1879

In 1874 a stockman, JE Wright of Foxlow Station, recognised copper mineralisation when he was about 12 kilometres south of the station. The find was on the banks of the Molonglo River. Several small mines were soon operating along the ridge above the river, and the village of Captain's Flat was established.One mining company established in the 1880s was Lake George Mines. It's name was to remain synonomous with the name of the town until mining and treatment ceased on 11 March 1962.

Jan 1, 1993

THE exceptional rainfall characteristic of the West Coast of Tasmania, in conjunction with the rugged topography of the district, has always suggested the utilization of water-power, and from the earliest days of the Mount Lyell Company theeventual installation of a hydro-electric power scheme, making use of some near-lying lake, has constantly been kept in view. At the period of the inception of the company, however, the time was not ripe for such an undertaking, and it is only oflate that the various important considerations involved have sanctioned incun;ing the heavy expenditure necessary, with the positive assurance of permanently reaping the benefits expected. The West Coast of Tasmania contains many lakes of varioussites; situated at high levels, and, although the catchments of these lakes are not very extensive, still, the excessive rainfall is so constant over long periods that its regularity may be relied on as offsetting the limited catchments. The explanation of the abnormal rainfall is simply the circumstance that the West Coast Range forms the first high land barrier which is met by the moisture-laden westerly and north-westerly winds blowing off the Southern Ocean. By the time the clouds strike the mountains they ride very low, consequently the elevation of the range, the peaks of which do not exceed 3000 to 4000 ft. above the sea, is sufficient to cause a copious precipitation. Lake Margaret, which is situated five miles north of the reduction works, was first recognized as a possible source of waterpower by Mr. Hugh Ohrisp, a surveyor, who visited it about 1893-4. Earlyl in 1895, while the preliminary work on the erection of the first furnaces of the Mount Lyell Co.'s reduction...

Jan 1, 1915

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974