Search Documents

By D L. Decker, G C. Miller, C Papelis

Arsenic, often associated with precious metals ore deposits, is a major contaminant released during large-scale gold mining. Because of the complex oxidation/reduction and sorption behaviour of As, prediction of the long-term mobility of As in pit lakes is uncertain. The behaviour of As in pit lakes is investigated in this paper by conducting a series of laboratory experiments where As is allowed to adsorb onto pit lakes sediments. Experiments were conducted over a range of pH with both As(III) and As(V) allowed to adsorb onto sediments collected from existing pit lakes found in the three main orebody types in Nevada, USA; porphyry copper, quartz-adularia gold, and Carlin Trend type gold deposits. Results from adsorption experiments show that As(V) and As(III) adsorption is strongly pH dependent with higher uptake at pH 5 and lower uptake at pH 9 for As(V) and higher uptake at pH 9 and lower uptake at pH 5 for As(III). This behaviour, as expected for oxyanions, has been described previously for agricultural soils, iron oxides, and Carlin Trend heap materials. Maximum adsorption of As(V) for the Carlin Trend type gold sediment was 3.0 g/kg at pH 5, 2.0 g/kg for the quartz-adularia sediment, and 0.9 g/kg for the copper porphyry sediment. Maximum adsorption of As(III) for Carlin Trend type gold sediment was 2.5 g/kg at pH 9, 2.2 g/kg for the quartz-adularia sediment, and 2.1 for the copper porphyry sediment. Adsorption isotherms are non-linear and show Freundlich isotherm behaviour. Variations in sorption between the different pit lake sediments under similar conditions can be explained by differences in the elemental composition of the sediment. Most rock forming elements from XRF analysis are similar in quantity except for Fe. The Fe content is highest in the Carlin Trend type gold deposit sediments and lowest in porphyry copper deposit sediments and is the third most abundant element in all three sediments. The Fe content of the sediments correlates well with the amount of As sorption seen in the laboratory experiments.

Jan 1, 2003

In high stress mining environments, production drill rigs are often employed for rapid drilling of boreholes for systematic cable bolting. One outcome of this drilling method is the need for larger boreholes than would normally be drilled using customised bolting machines, such as the Tamrock Cabolter. Past laboratory studies indicate that, under ideal grouting conditions, borehole diameter has little effect on the pull-out strength of cable bolts with high bulb densities. However, the sensitivity of pull-out strength to large boreholes and less ideal variations of grout strength have not been investigated. To explore these sensitivities, industry standard single embedment tests were conducted on large boreholes simulated using steel pipes. Four borehole diameters were tested, namely: 42 mm, 52 mm, 81 mm and 106 mm. In each case the grout water to cement ratio was varied from 0.35 to 0.45 and two cable bolt bulb spacings were considered, namely: one and three bulbs per metre. The results indicate that, across the range of parameters tested, variations in peak axial load at failure corresponding to changes in hole diameter were statistically insignificant.

Nov 25, 2010

By M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is underway at the Twin Cities Metallurgy Research Center, Bureau of Mines. The new route from concentrate to metal includes 2-stage fluid-bed treatment; pelletized concentrate (33 percent Cu, 7 percent S) is first desulfurized (to about 0.5 percent S) in an oxidizing atmosphere, and in the second stage the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10 percent CaO is routed to a smelting furnace to separate metallic copper from the gangue. Recovery and the Cu content of the product at this point are in the 97-98 percent range. The metal must be refined to remove sulfur and iron to make wirebar copper. An important feature of the process is the pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment, which has permitted shorter reaction time, decreased dusting, and facilitated subsequent processing.

Jan 1, 1970

By R. B. Schluter, M. M. Fine

A process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is under development at the Twin Cities Metallurgy Research Center of the U.S. Bureau of Mines. The new procedure includes a two-stage fluid-bed treatment in which the pelletized concentrate with 33% Cu and 7% S is first desulfurized to about 0.5% S in an oxidizing atmosphere, and then metallized by reduction with hydrogen. The reduced product is melted with flux to separate metallic copper from the gangue. The metal must be refined to remove residual sulfur and iron. The pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment is an important feature of the process, because it permits shorter reaction time, decreases dusting, and facilitates subsequent processing.

Jan 1, 1972

By T D. H McGrath, J P. Vaughan, J Heath, J J. Eksteen

A reliable laboratory method to characterise the response of free gold particles when subjected to flash flotation conditions has been developed by AMIRA P420 researchers at Curtin University. This test has been applied to assess the flotation recovery of gravity recoverable gold from free milling ores as well as synthetic ores featuring either a gravity concentrate or gold powder. Trends in free gold flotation kinetics as well as size and milling effects were identified for gold recovery, based on the different gold types, reagent dosage and residence time.CITATION:McGrath, T D H, Eksteen, J J, Vaughan, J P and Heath, J, 2013. Laboratory flash flotation trends for a variety of gold particles, in Proceedings World Gold 2013 , pp 357-366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Antimony ore samples (mean assay 18·7 per cent antimony) from Endeavour Inlet, Marlborough Sounds New Zealand, were tested for upgrading by flotation to a saleable product (60 per cent antimony).The effects of activating agents, collectors, frothers, pH, conditioning time, and particle size on the recovery and grade of a stibnite flotation concentrate were determined using HaIlimond tube and laboratory flotationcell test apparatus. Optimum flotation conditions for the ore were thereby established. A stibnite concentrate grading 63 per cent antimony and an overall recovery of 90 per cent is obtainable in a two-stage process.

Jan 1, 1977

By P. Lostritto, G. E. Agar, G. Labonte, M. Cherevaty

"A locked cycle flotation test was done on a sample from the ovoid portion of the Voisey 's Bay copper-nickel sulphide ore. The chemical conditions for this test were generated by prior independent testing. In this test work the time in each of the five separation stages was optimized prior to executing the locked cycle test. A numerical simulation of the continuous circuit material balance was done prior to the locked cycle test. The test results were not fully satisfactory because the flotation of pyrrhotite in the bulk rougher and cleaner stages was not consistent. The preliminary indication was that the samples had oxidized to varying degrees during storage.INTRODUCTIONINCO has performed batch laboratory flotation testing on ore from Voisey's Bay which is a mixture of chalcopyrite, pentlandite and pyrrhotite. Earlier, Lakefield Research was contracted by Diamond Field Resources to test the ""flotability"" of the ore, which included a pilot plant trial. INCO's J. Roy Gordon Research Laboratory has repeated many of the batch tests that Lakefield did to verify their results. Based on their own work, INCO has modified the circuit proposed by Lakefield Research. The modified circuit is based on batch test work, but no locked cycle test (LCT) was done. It is believed that this circuit will produce a copper concentrate at 29-30% copper and a primary nickel concentrate at 15-20% with recoveries of 80% or above.For several years the University of Toronto has been working with INCO to provide ""hands on"" experience for undergraduate students as an Industrial Research Project (IRP). This year, the objective for IRP was to optimize the time for each of the five separation stages for the Voisey's Bay ore then to numerically and experimentally simulate the material balance for a continuous circuit."

Jan 1, 1998

By A. Mukherjee, C. Kelly, B. Markovich, G. E. Agar, G. E. Robertson, F. Khan, B. Shea

"Laboratory batch flotation tests were performed on a sample of bulk slow cooled converter matte (Cu:Ni = I) to optimize the time in each of the separation stages. Numerical simulations were carried out to estimate a continuous circuit material balance for the conditions selected. An experimental simulation of a continuous circuit (locked cycle test) readily came to steady state and there was reasonable agreement between the numerical and experimental results. The use of nitrogen as the flotation gas and the addition of collector to the grinding mill minimized the oxidation of chalcocite, which has previously resulted in increasing circulating loads, and led to a stable circuit with very low weights in the recycle streams.IntroductionINCO Limited developed a flotation process for separating the components of copper-nickel matte [Sproule, Harcourt and Rose 1945; Sproule, Harcourt and Renzoni 1960] in 1945 to replace the Orford process and continues to use the flotation process in almost the original mode to this day. Initially the matte processed was the result of smelting a nickel concentrate that analyzed about 12% nickel and 2% copper and all of the recycle material that was generated in the smelting process. The matte generated analyzed about 25% copper and 53% nickel, roughly 2: 1 nickel to copper. This matte was blown in Pierce-Smith converters to be sulfur deficient in order to produce a metallic phase that collected the precious metals contained in the smelter feed [Wilson and Stratton-Crawley 1991]. This process continued with little change until 1994 when the separation of chalcopyrite from pentlandite in the Copper Cliff mill was discontinued after 63 years of operation. As a consequence of the elimination of the primary separation of chalcopyrite from pentlandite in the milling process a bulk concentrate was produced for smelting. Bulk concentrate smelting came into practice in 1994 as part of the initiative to meet government legislation that restricted the emission of sulfur dioxide to the atmosphere. Previously, the copper concentrate was smelted in an INCO oxygen flash furnace which resulted in the capture of a high strength sulfur dioxide stream from which liquid sulfur dioxide was produced. Nickel concentrate was smelted in reverberatory furnaces that produced low strength sulfur dioxide gases which were difficult to treat. The action taken by INCO to meet the environmental constraints was to smelt a bulk concentrate in oxygen flash furnaces which would produce gases suitable for the production of liquid sulfur dioxide and another stream that was high enough in sulfur dioxide to be readily converted to sulfuric acid [Bell et al 1990]. The end result of this decision was that all the copper-nickel separation would be done in the matte separation plant."

Jan 1, 1996

By Russell B. Dix

Laboratory column leach tests are used routinely to evaluate gold and silver ores for heap leaching. The tests are fairly straightforward. The ore to be tested is placed into an appropriately sized leach column. Then an alkaline cyanide solution is applied to the ore and the effluent solutions are collected. The effluent solutions are then put through a column of activated carbon to recover the gold and silver in solution. Zinc precipitation may also be used for silver ores or if the ore contains a significant amount of soluble silver in addition to gold. The length of the leach time in the tests is mainly a function of how quickly the precious metals are recovered from the ore. At the completion of the tests, the tailings are assayed and the recoveries determined from the calculated head grades. The amount of ore to be used for a test is partly a function of its crushed size. The coarser the size, the larger the sample size for the column. A typical small-scale laboratory column test on ore crushed to -12 mm (-0.5 in.) would usually be conducted in a 100- to 150-mm-diam (4- to 6-in.-diam) column 2 m (6.6 ft) in height, containing about 20 to 45 kg (44 to 99 lb) of ore. A comparable test on the same ore crushed to 50 mm (2 in.) would be conducted in a 200- to 300-mm-diam (8- to 12-in.-diam) col¬umn 2 m (6.6 ft) in height, containing about 80 to 200 kg (176 to 441 lb) of ore. Larger-scale tests can be run by increasing the column heights and diameters. Conducting larger-scale tests results in increased costs for sample procurement, preparation, and running of the tests. The additional data obtained from

Jan 1, 1989

By Glenn M. Boyce

This paper discusses the results of a laboratory testing pro- gram to determine the validity of hydraulic fracturing stress measurements in salt. Tests were performed on 15 cm diameter samples loaded under hydrostatic stress conditions to determine the influence of time, confining pressure, flow rate, borehole diameter, and packers on breakdown pressure. Tests were also performed in a polyaxial loading frame to determine whether or not hydraulic fracturing could be used to measure non-hydrostatic stresses. The test results indicate that the breakdown pressure is not affected by time delays of up to 64 hours between the application of load and fracturing the rock. Breakdown pressures were found to fall short of predicted elastic values at higher confining pressures for the hydrostatic tests. The ratio of the horizontal stresses in non-hydrostatic tests had no effect on breakdown pressures. Flow rate and borehole diameter variations were found to have a marked effect on breakdown pressures. Shut-in pressure values, which are generally used as an indication of the minimum stress value, exceeded the applied minimum stresses by 10 to 60% depending on the method of determination used. The lack of a relationship between breakdown pressure and horizontal stress ratio may preclude hydraulic fracturing from being used in salt as it is conventionally applied in brittle rocks.

Jan 1, 1984

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer-still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The dewatering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilterable, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf.

Jan 7, 1959

By A. M. Johnson, M. A. Cornachione

The west central Upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur that can create emission problems when processed in a kiln. A low-cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated. In this study, optimal conditions for the bacterium Thiobacillus ferrooxidans were created to promote pyrite oxidation and, therefore, sulfur removal from the slate. Preliminary lab scale flask tests using crushed and sized slate (-40 + 100 mesh) and T. ferrooxidans bacteria in a sulfuric acid medium resulted in 70% oxidation of pyrite over a one-month period. Subsequent column leaching tests on coarser materials (-3/8+1/4 in.) operated for six months resulted in a maximum reduction of total sum of 75%. These data suggest that bio-heap leaching to remove sulfur from the slate for use as a kiln feed material is viable.

Jan 1, 1995

By M. A. Cornachione

The west central upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur which can create emission problems when processed in a kiln. A low cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated.

Jan 1, 1992

By Bo-Hyun Kim, Steve Berry, Mark K. Larson

"When coal pillar bursts occur, they involve the sudden expulsion of coal and rock into the mine opening. These events occur when relatively high stresses in a coal pillar, which serve as support in underground workings, exceed the critical capability of the pillar. This causes the pillar to rupture without warning. A cleating is a type of naturally occurring joint system unique to coal seams. However, cleatings are pervasive throughout the coal seam and are much more tightly spaced than joints occurring in other rock types. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated 84 coal samples obtained from a Utah coal mine by conducting both unconfined and triaxial compressive tests in order to examine the response to stress as a function of both confinement and orientation between cleat and loading direction. The results of the study show that the confining pressure dictated not only the peak compressive strength but also the brittleness as a function of the major-to-minor principal stress ratio. The spalling limit of the coal estimated by the s-shaped brittle failure criterion appears to be very dependent on the angle between the cleat and the loading direction, particularly at lower confinement.INTRODUCTIONCoal pillar bursts, or bumps, remain a most critical safety concern in underground coal mining, despite significant advancements in engineering controls. As shown in Figure 1, between 1983 and 2014, there were nearly 400 cases of reportable dynamic failure accidents in coal and nonmetal mines, resulting in 20 fatalities, 155 lost-time accidents, and an estimated 48,000 lost man hours (MSHA, 2015). These types of events have been documented for well over 100 years within the American underground coal mining industry. During this time, mining practices and support technologies have evolved considerably, resulting in an overall decrease in the rate of dynamic failure-related injuries and fatalities. Although techniques and practices of mining are highly advanced, coal pillar bursts, or bumps, continue to occur (Mark and Gauna, 2015). If coal is expected to fail in a brittle manner, behavior changes associated with relatively low tensile strength, such as the transition from tensile to shear failure, have to be considered and reflected in the adopted failure criteria. Rock failure in tension takes place at low confinement around excavations due to tensile failure in heterogeneous rocks (Diederichs, 2007). The prospect of tensile-dominant brittle failure diminishes as the confinement increases away from the excavation boundary. Therefore, it is expected that the transition from tensile to shear mode in the failure mechanism occurs as the confinement level changes and conditions for tensile failure are prevented or strongly diminished. In addition, many uncertainties remain because of the highly anisotropic characteristics of coal seams associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous effort is required to better understand the catastrophic failure mechanisms in coal mines."

Jan 1, 2018

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By J. A. Organiscak

Enclosed cabs are a primary means of reducing the silica dust exposure of equipment operators at surface mines. The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on enclosed cab air filtration system performance. Factors experimen­tally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use and wind velocity effects on cab penetra­tion (inside to outside cab concentration ratio). Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab penetration .Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By J. A. Organiscak

The National Institute for Occupational Safety and Health (NIOSH) has investigated various factor effects on cab air filtration system performance. Factors experimentally investigated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that the intake filter efficiency and recirculation filter were the two most influential factors on cab protection performance. Use of a recirculation filter significantly reduced cab penetration over the intake air filter by itself due to the multiplicable filtration of the cab interior air. Cab penetration was also affected to a lesser extent by intake filter loading and air leakage. Adding an intake pressurizer fan notably increased intake airflow and cab pressure while providing only minor changes to cab penetration.

Jan 1, 2008

By Jarret Thomson

An understanding of groundwater flow is essential for many aspects of mining. This is especially true for the process of shaft sinking through the sandstones of the Manitou Falls Group in the Athabasca Basin of northern Saskatchewan. Experience has shown that the hydraulic conductivities of these sandstones can be relatively high, especially in zones containing natural fractures. To develop a better understanding of the inflow potential into a shaft, a laboratory testing program was undertaken to investigate the hydraulic conductivity of fracture core samples from the Manitou Falls Group. This program involved the measurement of hydraulic conductivities under steady-state flow conditions, while cycling the effective confining pressure across a span that is representative of in-situ conditions. The change in fracture aperture was simultaneously recorded at each confining stress level. It was found that existing relationships relating aperture and flow did not accurately capture the behavior of the samples tested. The effects of fracture staining and infilling were also investigated, and were found to have a notable impact on the hydraulic conductivity.

Jun 1, 2012

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015