Search Documents

By A. Vidyadhar

Printed circuit boards (PCBs) constitute a majorpart of electrical and electronic equipment containing valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, Pb, etc. The concentration of base and precious metals in PCBs is observed to be several times more than those in their respective ores. Therefore, the recycling of PCBs is necessary to recover the valuable materials. However, the ultrafine particles pose a big challenge. Removal of them is suggested prior to processing by flotation. Froth flotation is observed to be a promising technique for rejecting the plastics from the comminution product. In the present work, enrichment of ground 1.0 mm PCB powder was investigated through flotation route by varying the operating variables such as frother dosage, pulp density, air flow rate and rotational speed of the impeller. The liberation studies indicate that excellent liberation of metal values is achieved from the non-metallic constituents at -1.0 mm size and below. The particulate system is quite rich in metal value with about 23% total metal content. The non-metallic constituents such as plastics are observed to possess strong hydrophobicity while the metal particles in the pulverized mass are hydrophilic in nature. Froth flotation kinetics is studied in depth with a view to facilitate high rejection of plastics and identify optimum operating conditions for the same. A number of experiments are performed to establish the influence of the operating variables on flotation performance. The conditions for achieving higher yield of the metal-rich fraction with respect to a specified grade are discussed in the light of the experimental results. It is found that the requirement of reagents is negligible which could be a very important factor from the commercial stand point. Single-stage flotation increases the metal content from 23% to over 32% with a mass yield of around 75% and over 90% recovery of metal values. 32% of the materials in the feed could be effectively rejected in the float fraction losing less than 4% metal values. The dependence of kinetics on the process variables is also discussed. It was concluded that a high rotor speed helps in efficiently rejecting the plastics. Frother should be added to help stabilize the froth and enhance the kinetics. A moderate air flow is required while pulp density must be kept low for efficient pre-concentration. It is established that the entire -1.0 mm comminution product could be treated by flotation for generating a pre-concentrate. Keywords: printed circuit boards, recycling, froth flotation, kinetics, recovery

Sep 1, 2012

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By David Langberg

Recovery of dissolved copper from discard slags is a critical consideration affecting the economics of copper smelting. Slag cleaning is frequently carried out in electric furnaces, however reduction by injection of natural gas in a holding furnace may offer a lower cost alternative in some circumstances. As the residence time of the injected gas is short, the factors controlling the rate of reduction need to be clarified in order to optimise the design of the slag cleaning furnace. A series of medium scale (200 kg) reduction tests to investigate the rate of reduction of copper-containing slags by injection of natural gas-nitrogen mixtures between 1150-1250C was carried out by CSIRO Minerals. The composition of the gas in the top-space of the reactor was found to be significantly more reducing than the slag, indicating that thermodynamic equilibrium was not established between the slag and the gas in the bubble plume. An apparent first order rate law was observed between the rate of oxygen elimination from the bath and the magnetite concentration of the bath. The dissolved copper concentration was closely correlated with the oxygen potential of the slag, suggesting a partial equilibrium between the dissolved components of the slag. The utilisation efficiency of the natural gas decreased as the natural gas flow rate was increased. The results of the tests tend to indicate that the rate is controlled by a mixed reaction kinetics/ mass transport mechanism. The work was supported by Xstrata Copper ? Mt Isa Mines.

Jan 1, 2006

By Allen Pratt, Guy Deschênes, Mike Fulton, Hai Guo

Calaverite is a gold telluride species, with the composition, AuTe2. Calaverite is usually characterized by an exceedingly slow dissolution rate in a cyanide solution. Cyanidation of a slurry containing synthetic calaverite (P90 of 10 microns) was studied to determine the leaching kinetics and surface reactions. Alkalinity, dissolved oxygen, lead nitrate and sulphide minerals (pyrite and chalcopyrite) were among the parameters evaluated. The reaction products at the surface of calaverite were documented using X-ray photoelectron spectroscopy. High lime concentration with lead nitrate and injection of oxygen produced the fastest leaching rates. New gold leaching mechanisms were identified which appeared to be related to the parameters selected.

Jan 1, 2005

A composite iron ore-reductant pellet is a mixture of fine iron ore and fines of coal/char/coke, bonded at essentially room temperature with sufficient green strength for subsequent handling. In ironmaking, these pellets offer the advantage of fast reduction, utilisation of fines, non-coking coal and coke breeze. The composite pellet-based alternative ironmaking processes constitute a promising route for ironmaking in future. The present paper is a brief review of kinetics and mechanism of reduction of iron oxides into iron and other associated reactions, when these pellets are heated to high temperature. It would draw significantly from investigations conducted by the author and his co-workers.

Jan 1, 1999

By M. Kinne

Catalyst preparation/ characterization Slightly modified DP (~Schumacher et al. Catal. Lett. 89, 109, 2003) CeO2 HAS 15 from Rhodia calcined in air for~ 2h BET: ~188m2/g, particles size: 5.7nm (TEM, XRD) + HAuCl4 at pH of 6.5-7, (>95% of the Au was deposited) ? Au/CeO2 (2.6wt% Au, ICP-AES) A new conditioning procedure was applied, including heating at low temperature in N2 and H2/N2 mixtures) Patent DE 10205873A1. Very small Au particles <2nm, for CO oxidation catalyst as Au/TiO2, Au/Fe2O3, and Au/Co2O3 Here Au particles size <3.5nm (XRD) Summary ? CO is nearly exclusively adsorbed on the Au particles ? Positive reaction orders of 0.5 are found for CO and H2O ? Ea= 40kJ/mol ? The catalyst is very active and stable ? During WGS reaction huge amounts of formates are formed and cover the surface ? The activity of the catalyst seems to be correlated with the formate species.

Oct 1, 2003

By K. M. Parida

The kinetics of dissolution of manganese dioxide in dilute sulphuric acid solution have been investigated using iron pyrites as a reductant. The dissolution rate of manganese is independent of the speed stirring but depends upon temperature, particle size, specific surface area of manganese ore, acid concentration, Fe(II) concentration and amount of pyrite. The activation energy is 43.6 KJ/mol and the linear relationship between the rate of dissolution and lido indicates that the reaction is chemically-controlled. The redox reactions of MnO2 with iron pyrites and Fe(II) are the rate-controlling reactions.

Jan 1, 1990

By Glastonbury J. R

The kinetics of the direct chlorination of, zircon in the presence of carbon was studied at temperatures between 9000C and 12000 C. From the experimental data it is prop- osed that the most likely mechanism for metal oxide (MeO2) chlorination is as follows: At I Surfaceon zMeO2+ZMeCl - MeOC12 (1) At Carbon MeOC12+C+Cl MeC14+CO (2) Surface It.is envisaged that this type of mechan- ism would occur for both the zirconium and, silicon. constituents of the ore. In the above mechanism; the surface re- actions appear to be fast and not rate controll- ing. In a carbon surface deficient bed the diff- usion of oxychloride intermediate through the boundary layer to the carbon surface becomes the rate controlling step. In a zircon surface deficient bed the diffusion of oxychloride away from the zircon surface controls the reaction. This postulated mechanism can be used to ex-, plain the observed experimental effects.

Jan 1, 1973

By C. F. Ferron

A process has been developed to treat the copper gold ores from the Guelb Moghrein mine in Mauritania. The process consists of pressure leaching the sulphide concentrate, neutralising with the oxide ore, recovery of copper by SX/EW and of gold by cyanidation of the autoclave residue. This paper focuses on the pressure leaching step, and presents data from bench and pilot plant test programs. In particular, attention is drawn to the effects of temperature, grind size, neutralisation, retention time and solution recycle on the kinetics of copper dissolution from various flotation concentrates. Likely leach mechanisms are briefly discussed.

Jan 1, 2000

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette&apos;s core. The measurement of the carbon content on the globules and the external iron layer is also presented.

Jan 1, 2003

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette&apos;s core. The measurement of the carbon content on the globules and the external iron layer is also presented

Jan 1, 2003

By Zhou A, Cadogan J. M

Direct reduction of iron ore (DR) is one of the promising technology emerging in the world&apos;s steel industry. Kinetics and Mossbauer studies of DR with hydrogen have been carried out at two temperatures of 600¦C and 800¦C in this investigation. The results show that different controlling steps govern the reduction rate at different temperatures. The mechanism was also found to vary during the reduction. The Mossbauer spectra of the samples reduced in various time intervals were studied to determine the phase changes during reduction.

Jan 1, 1997

By Shengli Wu, Feng Chang, Hua Lu, Jianliang Zhang

Kinetic studies of the blast furnace dust (BFD) reduction process have been carried out under non-isothermal conditions. BFD pellets were made with bentonite as the binder. A Comprehensive Thermal Analyzer (TG-DSC) was used to determine the mass loss of pellets, which were heated at three heating rates of 10, 20, 30 K/min up to 1493 K. Furthermore, the metallization rate and mineral composition of BFD pellets heated to several different temperatures were analyzed by chemical analysis and X-ray diffraction (XRD). It was found that, with its inherent carbon resources as the reducing agent, the metallization rate of BFD pellets could reach 88% at most. The reduction and weight loss process of iron oxides mainly happens above 1273 K. In addition, from application of the Coats-Redfern equation the apparent activation energy of the reduction from wustite to Fe was 443 kJ/mol and the mechanism was interface reaction R..

Mar 1, 2017

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluoridesl.2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02?SiO2) with the ammonium acid fluoride (NH4F?XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo-dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By C. J. Pretorius

More than 30 percent of the global demand for zircon (ZrSi04) is supplied by South Africa. A significant amount of the zircon is exported, and beneficiated products are then imported for industrial applications locally. Beneficiating the zircon locally could have a positive impact on the local market, since zircon is only one of many such cases. Ammonium acid fluoride serves as an alternative anhydrous fluorinating agent for zircon in the synthesis of several metal fluorides1,2. It provides an effective dry fluorinating method and is easier to handle than hydrogen fluoride or fluorine gas. Zircon exposed to extreme plasma temperatures dissociates and becomes more reactive. The reaction of the plasma-dissociated zircon (Zr02.SiO2) with the ammonium acid fluoride (NH4F.XHF, where x= 1 to 5) forms two main intermediate compounds (NH4)3ZrFr(s) and (NH4) 2SiF6(s), the latter decomposing to form volatile products at relatively low temperatures, providing easy separation of the silicon and zirconium compounds. The ammonium zirconate compound decomposes to form zirconium tetrafluoride (ZrF4), which can be further manufactured into zirconium metal, to name but one product. Data on the kinetics of the reaction of ammonium acid fluoride with zircon and plasma-dissociated zircon, combined with the thermo¬dynamic parameters of the reaction, is essential for the development of an industrial process for the production of a precursor for the manufacturing of zirconium metal, namely anhydrous ZrF4. Both the reaction kinetics and reaction parameters will be included in this study, as well as some proof that the reaction proceeds to ZrF4 on a small batch scale. If the exact reaction parameters can be pinned down, a wide spectrum of anhydrous metal fluorides can be synthesized through this fluorination route.

Jan 1, 2012

By P. C. Chaubal

The overall kinetics of oxidation of single partic1es of chalcopyrite have been studied for temperatures up to 1273 K. The experiments were conducted in a stationary bed reactor using a non-isothermal technique. Any mass and heat transfer effects on the kinetics of oxidation were eliminated by using a high-enough gas flowrate. Up to temperatures of 873 K, pore-bl1ocking kinetics were applicable, whereas above 873 K, power-law kinetics gave a satisfactory fit of the data. The activation energy was 215 kJ/mol below 754 Kand 23.7 kJ/mol above 1,060 K. Predominance area diagrams were constructed at various temperatures and used in conjunction with X-ray analyses of partially oxidized samples to determine the intermediate phases formed during the reaction. The analysi1s also provides a justification for the kinetic models used. The results indicate that the reaction rate is first order with respect to oxygen concentration and inversely proportional to the square of the particle size throughout the ranges of temperature studied.

Jan 1, 1985

By Xiang Ma, Halvor Dalaker, Kai Tang, Stefan Andersson

Silicon carbide (SiC) is one of the most important non-oxide ceramic materials for many industrial applications and is mainly synthesized by carbothermic reduction of silicon oxide by coke above 2200°C. Replacing natural gas (mostly methane, CH4) for coke in SiC synthesis could considerably reduce energy consumption and CO2-emissions owing to higher carbon activity of CH4 at lower temperature. The generally accepted reaction mechanism is that SiC is synthesized through gaseous intermediate silicon monoxide, SiO. In the present study, the reaction mechanism for the SiO and CH4 gaseous mixture has been examined using atomic scale modelling. Molecular dynamics (MD) using a reactive force field (ReaxFF) has been utilized to examine the initial stages of reactions involving a gas mixture of SiO and CH4 and surfaces of SiC. The MD results revealed some interesting SiC formation mechanisms. The reaction energies of the critical intermediate species were also estimated by density functional theory (DFT) calculations and the implications for the force field parameters used in ReaxFF was discussed.

Jan 1, 2015

By Michael Nicol

A quantitative description of hydrometallurgical operations depends primarily on an understanding of the kinetics of the chemical and physical processes that take place in such operations. This paper will review the current status of kinetics in hydrometallurgy in terms primarily of the author’s experience in diverse unit operations. A distinction will be made between the popular use of models based on limited kinetic data and mechanisms which reflect the actual elementary chemical or physical steps involved in an overall process. Several examples will be used to illustrate this distinction. The proliferation of published papers of declining quality has resulted in the bequest to later researchers of outdated and often incorrect conclusions by a process that is often difficult to reverse. Some examples of these mysterious concepts will be examined and hopefully reversed. Finally, several examples will be given that identify significant gaps in our understanding of the kinetics of important processes that remain unresolved.

Jan 1, 2014

By C. Hecker, J. A. Garcia

To determine the kinetic reaction mechanism, electrochemical experimental techniques of stationary polarization, linear voltammetry and faradaic impedance were used. Gold electrodeposition experiments were realized using an electrolysis cell, provided· by a rotary disk of vitreous carbon and or' platinum counter electrode of platinum mesh and reference electrode. Using an automatic measurement system voltarnmograrns and Nyquist faradaic impedance spectra were obtained. In this paper, responses for different cases were analyzed through faradaic impedance criteria, considering several kinds of diagrams obtained. The importance diffusion influence of aurocyanide ions and adsorption as controlling steps previous charge transfer was verified. A model of proposed mechanism is discussed.

Jan 1, 1997

By C. E. Jordan

Direct digestion of phosphate ores by the acid-alcohol method offers improved leaching selectivity for the exclusion of iron and aluminum in the product acid. The leaching kinetics of this process will have a major role in the eventual application of this technology. The Bureau of Mines investigated apatite dissolution to determine the reaction rate and mechanisms of the leaching kinetics. The dissolution kinetics were monitored on various sized fractions of pure apatite. The "shrinking-core" kinetics model was applied to the data to determine the rate controlling mechanisms. For each size fraction, the initial reaction rate was controlled by the dissolution reaction. After an hour the dissolution rate slowed indicating a diffusion controlled reaction caused by the formation of calcium sulfate hemi-hydrate coating on each particle. For complete dissolution of the apatite, the phosphate rock should be ground to near 10 µ m size.

Jan 1, 1993