Search Documents

By N. S. Tanious

This paper summarizes the results of an investigation into possibly the largest coal pillar failure in the USA. The newly opened drift mine is located in Southeastern Kentucky and worked an 11 feet thick coal seam, all other mines in the District worked seams 4-5 feet thick. The initial mine development consisted of 14 main entries (Fig. 1) which were driven in two sets of 7, under increasing depth of overburden. As the left seven entries came under deeper overburden the pillar ribs began sloughing which caused many of the concrete-block ventilation stoppings to crack. The mine management stopped the advance in the left seven and continued with the right seven entries. During the spring of the following year development resumed in the left seven, rib sloughage occurred again and this time severely cracked many stoppings and many were totally disintegrated from the excessive deformation. Within few weeks the sloughage was so heavy that many of these entries behind the active face were filled with piles of sloughed coal slabs. When the face reached a depth approximately 1150 feet, the sloughage became a slow, massive squeeze. The entry convergence (closure) reduced their height from 11 to 7-8 feet and the squeeze spread back to shallower depth covering an area roughly 300 pillars.

Jan 1, 1989

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

By David Garry, Michael J. Brnich, Lynn L. Rethi, Henry P. Cole, William J. Wiehagen, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet and the trainee's questionnaire. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.1 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Supervisors, Safety Personnel and Accident Investigators Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Developing a strategy or plan to prevent slips and falls Following correct procedures in conducting an accident investigation Preventing unsafe work practices Recognizing and instituting hazard controls in the section Identifying and implementing safe work procedures Location: Underground coal mine section Problem: You have been the general mine foreman at White Rock Mine for 4 years and have worked at this mine for 12 years. The mine superintendent calls you into his office. He gives you an accident report of an employee in 4-G section who was injured while carrying rock dust bags from the rock dust car to a battery powered scoop. It is several days after the accident and the mine superintendent assigns you and the safety supervisor to thoroughly investigate the accident to determine all the contributing factors. Your job is to make specific recommendations to prevent future slipping/tripping accidents.

Jan 10, 1999

By Gary Buchan

"Mine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mine operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. The acoustic emissions (AE) form of non-destructive testing has been used for decades to determine material or machine deterioration or potential failure. This paper presents the findings of research in AE with the results of laboratory bolt pull tests and comparisons to field experimentation, including AE sensors and bolt load data in an underground stone mine. The goal of the project is to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of predicting bolt failure or roof deterioration.INTRODUCTIONMine-wide ground control stability is essential to any mining operation to prevent catastrophic failure of underground structures. The ability to recognize or indicate the potential for ground control hazards in underground mining operations is highly desirable to reduce or eliminate ground-control-related injuries and fatalities. Typical ground control monitoring devices involve drilling into roof or rib, grouting or gluing of sensors, and dedicated cabling for data collection. One of the original goals of this research was to develop a methodology for a simple wireless device that could provide an indication or warning of potential roof bolt or roof failure. Various types of nondestructive testing (NDT) have been used for decades to determine material or machine deterioration or the potential failure of either. One type of NDT is acoustic emission (AE) monitoring, which has been studied for use in mining to predict rock bursts and mine failures since the 1940s (Obert, 1941; Obert and Duvall, 1942). The primary goal of the work was to compare laboratory results of AE sensors on roof bolt pull tests with field experimentation to determine the capability of evaluating bolt loading or roof deterioration in an underground stone mine. Bolt pull tests were conducted in the laboratory to establish a repeatable trend of AE activity versus bolt load. The second part of the project was to then install bolt load cells in an underground stone mine and monitor AE activity in the vicinity of mining."

Jan 1, 2018

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Hydraulic transport is commonly used in mining for moving particles or ore concentrates in pipes over long distances with a water stream. Control and monitoring of this process require sensor technology that can obtain relevant characteristics of the two-phase flow. This work investigates the acoustic emission (AE) technology for monitoring a hydraulic system with different sand concentrations, showing the strong relationship between friction behavior in the pipe and the measured AE signals.

Apr 1, 2023

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Jan 5, 2023

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By BURCU NILGUN CETINER, Serdar Aktas

Antimony has been used extensively in industry and in everyday life since the 19th century, and antimony sulfides have been known since around 4,000 B.C. Antimony’s most significant applications are as a flame retardant in the manufacture of electronics and textiles, as a catalyst for plastic fabrication, and as paint pigment and fining agent in glassware, opacifier in ceramics and an alloying element in ammunition and battery manufacturing plants. It is also used in vehicle brakes and tires. Brake pads contain stibnite (Sb), the sulfide compound of antimony. In particular, stibnite is used in automobiles as a lubricant, vibration reducer and friction stability improver. Anthropogenic activities are the primary source of antimony in the atmosphere [1,2]. Annual global consumption of antimony has increased to more than 1.4 × 105 t, and China is the most significant producer [2].

By J Rutter, M NoppT

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. Ridgeway is an underground sublevel cave (SLC) operation mining approximately 5.6 Mt of gold-copper ore per annum. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Drawpoint recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Grade control at Ridgeway has been based upon sampling the ore from SLC drawpoint bunds using 15 kg grab samples combined to form 30 kg samples prior to assay. This large sample size was selected in an attempt to representatively sample the coarsely-sized broken ore, the samples collected having a nominal diameter of about 130 mm. The assay results for gold and copper from these samples are extremely variable and the usefulness of the results has been questioned by the mine, particularly given the onerous and OH&S hazardous activity of handling large sample masses. Granulometry testwork at Ridgeway confirmed the extent of the relationship of decreasing sample grade variability with particle size. Based on this relationship, drawpoint sampling tests were carried out using 9 kg samples sieved to -45 mm at the drawpoint site. The gold and copper results from the finer 9 kg samples were significantly less variable than those from the normal, coarser 30 kg samples. The variance reduction was similar to that predicted from broken ore sample theory for the selected sample mass and nominal particle size. This relationship therefore allowed Ridgeway to assess the sample mass and particle size required to achieve a particular precision. In addition to improving the precision, the reliability of assay results from smaller samples from the fine particle fraction for drawpoint control depends on the accuracy of the results. The assumption is that the grade of the finer ore is similar to that expected from the lot, or that if a bias exists, then the extent of this bias is acceptable and consistent enough to be accounted for in the grade control system. The distribution of grade with particle size and the reconciliation of drawpoint sample and mine results is currently under investigation.

Jan 1, 2005

By T. Stergiou

An extensive research is being carried out on the shaft furnace operation in order to minimize down-times and reduce operational cost. The need to increase the scrap percentage on the charging mix, together with the need of cheaper spare parts has led to the investigation of alternative materials for the burner system on the shaft furnace. This system consists of a burner block and a flame holder. Traditionally these items are constructed either from SiC ? oxide bonded or SiC-nitride bonded. A lot of problems have been confronted over the past 8 years of operation. Usually, large cracks are formed on both flame holders and burner blocks. This resulted in leakage of combustion gases to the back of the lining and a quick erosion of it. Additionally, the burner blocks suffer from chemical erosion, due to the increased amount of scrap used in the charging mix and the presence of slag inside the furnace. Alternative materials such as stainless steel for the flame holder and alumina-chromia refractory for the burner block have been tested in terms of life-time and resistance on chemical erosion. Furthermore, additional changes have been made on the burner block design in order to alter the flame shape and improve the scrap melting operation.

Jan 1, 2007

By R. I. Pennington, J. L. Vanderbeek

Investigations have been conducted at Chino Mines Co. into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on laboratory, pilot, and plant scales to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 84% with a reduction in specific energy (kWh./t) of 88%. Test results obtained to date are presented.

Jan 1, 1987

By Umay Cinarli, Ahmet Turan

High-energy consumption in primary aluminum production (from bauxite ores) makes secondary aluminum production (from metallic raw materials such as scrap and dross) very critical. Aluminum dross, as a waste, arises in pyrometallurgical processes, and it is the mixture of metallic Al, Al2O3, other metal oxides, metal halides, and some other compounds like AlN. Aluminum dross has two subgroups (white and black) with respect to its metallic aluminum content. White dross is a secondary aluminum resource because of its high metallic aluminum content, whereas black dross, having low metallic aluminum content, is generally disposed in dumping areas. In the present study, it was aimed to develop a simple technique to valorize aluminum black dross in the form of alumina-based ceramic materials through pyrometallurgical (calcination) and hydrometallurgical (leaching) operations. Moreover, thermochemical simulations were conducted by using HSC Chemistry 6.12 software to simulate calcination conditions. After leaching experiments, an alumina-based ceramic containing approximately 36.8% Al2O3, 61.4% MgAl2O4 with 1.8% Na2FeO4, which might be available to use as a spinel refractory in steel smelting furnaces, was obtained in the experiment carried out in a solution containing 10 mLH2SO4 and 40 mL distilled water (3.5 M). Moreover, the sinterability of the alumina-based ceramic was investigated at the temperatures from 1350 to 1550 °C. In the sample which was sintered at 1550 °C, a density value of 3.15 g cm−3 and a hardness value of 69.58 HV were measured.

Oct 26, 2020

By Peter G. Kovalchik, Lawrence W. Scott, Thomas H. Dubaniewicz, Frank T. Duda

Overheating of electric cables on shuttle cars has long been recognized as a cause of premature insulation failure leading to shock and electrocution. Use of cable reels on shuttle cars can cause excessive heat build up which, in turn, causes the cable insulation to soften and become easily damaged This heat-softened insulation reduces the life of the cable. Repeated cycling of a cable in this manner can cause premature aging of the insulation; it becomes bridle, cracks and allows electrical leakage paths to farm. These leakage paths provide the opportunity for shock and electrocution to occur if miners come in contact with the damaged section of cable. It is imperative that cable operating temperatures be maintained at safe thermal limits. This paper discusses a research project conducted by the National Institute for Occupational Safety and Health, Pittsburgh Research Center to determine dynamically the conductor temperature of reeled shuttle car cables using fiber optics technology. The research portrays typical shuttle car loading cycles (both current and time cycles). Root-mean-square current loading is calculated based on the results. The thrust of this effort is to provide the scientific basis for ampacity derating factors specifically for mine machinery using reeled cables This information will reduce the probability of electrical hazards from reeled cables

By Martin Bouchard, Bruno Paillard, Jean-Claude Dubé, André L’Espérance

"A precise analysis of the noise emitted by an aluminum plant has shown that one of the main sources of noise is the noise emitted by an exhaust stack 40 m high and 1.8 m diametre, emitting a pure tone at 320 Hz. Because a classical cost effective solution is not available for this source, active noise control (ANC) solution was investigated.Commonly available ANC systems, how-ever, are not applicable to the chimney considered because the diameter of the stack (f) is too important compared to the wave length(?)of the frequency to control. In fact, until now, active noise control (ANC) has been successfully used to reduce the acoustical energy emitted at the end of ducts in the case of plane wave propagation, i.e. ?/f< 1.7 [1,4].When f> ?/1.7, high order modes propagate in the duct and a single canal active noise control system is not sufficient.This paper presents an ANC system developed to control higher modes in a circular duct. The controller used is based on a multiple-input, multiple-output adaptive filtered X-LMS and allows up to 11 error micro-phones and controls sources. The system has been used in a laboratory on a finite duct of3.5 m long and 0.30 m diameter which corresponds to the same ratio ?/f for the real stack. The efficiency of the system with different numbers and location of control sources and errors sensors has been analyzed. Noise reduction of 15 dB(A) could be obtained with some configurations. Actually, the system is being considered for installation on the real chimney stack."

Jan 1, 1997

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors&apos; previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

By H. R. Hanley

ELECTROLYTIC zinc produced from sulfate solution and, with pure lead anodes is always contaminated with a small and varying percentage of lead. The purpose of this investigation is to determine the characteristics of several lead alloys and their influence on the products of electrolysis and power consumption. The study of alloyed anodes has been a matter of interest for some years. Tainton, Taylor and Ehrlinger prepared a highly interesting paper1 on this subject a year ago, in which the effects of silver-lead and some ternary alloys of lead-silver-tin were described. The present paper describes a study of various combinations of 10 metals. The general plan of the work provides for the fabrication of the alloyed anode, its adequate conditioning by preparatory electrolytic operation, the production of cathode zinc and its analysis, the determination of the anode polarization, and other features. A list of the anodes tested, showing composition and polarization at various current densities together with the lead assay of the cathode zinc, is shown in Table 1.

Jan 1, 1930

By M. Saghaeian, R. Hejazi, V. Sheikhzadeha, A. H. Baladastian, A. Dehghani Ahmadabadi

This paper describes research done to remove apatite (phosphorus) from hematite ultrafine (70% finer than 25 micron) concentrate, recovered by electromagnetic separators at the FST Tailing Recovery Plant located in Chadormalu Iron Ore Complex through reverse froth flotation. As a result, iron and phosphorus content in magnetic concentrate (flotation feed) were 53.52% and 0.58%, respectively. Therefore, to increase the Fe content and decrease the P content of the sample, reverse flotation tests were applied. Chemical reagents used in this research consisted of sodium silicate as a depressant, sodium hydroxide and sodium carbonate as pH regulators, Alke & Dirol as fatty acid collectors and MIBC as frother. Process parameters including dosages of collectors, depressant and frother, preparation times of depressant and collectors, steps and time of frothing and pH range were selected. After doing flotation tests, in optimum condition, dosages of collectors were 1200 g/t, depressant 1200 g/t, pH in the range of 9.5 to 10, preparation time of collectors in the first step was eight minutes and at the other steps, four minutes; the number of frothing steps 4 and frothing time in each stage was three minutes. In this case, it was observed that the amount of phosphorus in the final concentrate was reduced to 0.05%, the Fe content increased from 53.52% to 61.66% and the Fe recovery achieved was 82.21%. Keywords: Iron ore, hematite ultrafine concentrate, iron and phosphorus content

Jan 1, 2020