Search Documents

By Rollin E. Hook, Attwell M. Adair

The response of CrzO3 and C~304 to various heat treatments was studied in are-melted iodide chromizim over the temperature range 1000" to 1750°C. These oxides, which are present as impurity phases in this material, were identified by X-ray diffraction teclzniques which were supplemented by optical metallop-aphy. As a function of increasing temperature, Crs04 is first observable in samples annealed at 1300°C and coexists with Cr2O3 (the low-temperature oxide) over a temperature range exceeding 200°C. As the temperature decreases, Cr3O4 dissolves with the concomitant precipttation of Cr2Y2. Both oxides precipitate predominantly at pain boundaries. The reactions which occur are involved with at least ternary equilibria, possibly due to iron which is present as an impurity in arc-melted iodide chromium. HILTY, Forgeng, and Folkman' reported in their investigation of the Fe-Cr-0 system that Cr3O4 (with about 8 pct Fe substituted for chromium) is a primary phase found in alloys with 9 or more pct Cr. They reported that this phase is stable only at high temperatures and that below the liquidus Cr3O4 is disproportionated into Cr2O3 and chromium-rich metal for both Fe-Cr-O alloys and in oxygen saturated pure chromium. Further, they proposed that CrsO4 forms by a peritectic reaction between Cr2O3 and the liquid. On the other hand, Hook, Garrett, and Adair2 found in their investigation of impurity phases formed in "pure" chromium (material consolidated from iodide chromium crystals) that Cr3O4 forms intergranularly and is stable as low as 1500°C which is 375OC below the melting point of chromium. The purpose of the research described herein is to determine the temperature range of stability of Cr3O4, and to show the nature of its decomposition. This further investigation indicates that Cr3O4 undoubtedly occurs in this material as low as 1300°C. The chromium studied was consolidated and fabricated from iodide chromium crystals (ICr-5) and contained Fe r 135 ppm, Si = 20 to 100 ppm, and 0 = 35 to 137 ppm. A complete chemical analysis is given elsewhere.' Annealing was conducted in 1 atm of purified helium and all samples were rapidly cooled (-200°C per sec) by withdrawing them from the furnace hot zone under a high flow rate of helium. The details of the electrolytic-etching technique and electrolytic-digestion techniques for preparation of insoluble residues for X-ray examination are given elsewhere also.' EXPERIMENTAL RESULTS The Starting Material. The as-swaged rod (final swaging done at 900°C) had a wrought grain structure and contained a dispersion of CrzO3 inclusions of maximum particle size of about 2 or 3 p, Fig. 1. The microstructure also contained a dispersed

Jan 1, 1964

By J. E. Burke

THE origin of so-called annealing or recrystalli-zation twins in face-centered-cubic metals continues to be a matter for speculation, and in the present report an attempt is made to explain their origin and to account for at least a majority of the observations concerning their behavior. The fact that annealing twins are prominent only The speelmen was deformed 8 pet in compression and then indented over the lower left-hand corner in a Rockwell in-denter, and then annealed to cause partial recrystallization. Note intense twinning in heavily deformed part and slight twinning in less deformed part. The upper right-hand corner is unrecrystalized. Area reduced approximately 25 pot for reproduction. after recrystallization suggests that deformation may be necessary for their formation. In 1926, Mathewson1 reported the observation by Phillips that annealing twins are frequently parallel to strain markings which delineate octahedral planes in the deformed (and partially recrystallized) matrix, and suggested that strain markings are mechanical twins which grow into annealing twins during recrystallization. Later work by Burke and Barrett' has shown that strain markings are traces of planes upon which slip has occurred, and that there is no evidence for the formation of mechanical twins of microscopically resolvable width in face-centered-cubic metals. Mathewson3 has pointed out, however, that slip may produce twin faults, and later modifications of this hypothesis have assumed that twin faults rather than true mechanical twins serve as the nuclei for annealing twins. Carpenter and Tamura5 suggested, also in 1926, that annealing twins might form by accidents of growth. A close-packed layer of atoms can be added to the octahedral plane of a face-centered-cubic metal in two possible positions, the right position

Jan 1, 1951

By C. H. Li, R. J. Stokes, T. L. Johnson

The effect of alumina particles on the nucleation and growth of cracks through a silver- chloride matrzx has been investigated. It has been found possible to promote fibrous cracking in dispersion-strengthened silver, chloride under notch-impact conditions at temperatures at which silver chloride alone cleaves brittlely The modification) of fracture beIzavzor is thought to be due to the relaxation of hydrostatrc stress beneath a notch by the nucleation of cavities near alumina particles. In recent years, composite or dispersion-strengthened materials have been studied primarily to understand their high resistance to plastic flow particularly at elevated temperatures. Dislocation models have been developed with which it is possible to deduce with fair success the effects of interparticle distance, particle size, temperature, upon yielding and creep behavior.l-4 Much less attention has been paid to the fracture behavior of these materials (with the notable exception of common structural steels) and little is known experimentally about the manner in which inclusions affect the nucleation and growth of cracks through a matrix. Nevertheless a beginning has been made in connection with fibrous cracking in ductile matrices where inclusions appear to play an essential ro1e.5-7 During the severe localized plastic deformation which accompanies necking in a tensile test, cavities are believed to develop at inclusions; these cavities subsequently grow and coalesce by plastic flow until separation is complete. It is of interest to consider whether inclusions can affect fracture behavior under loading conditions which restrict the plasticity of the matrix itself (for example, cleavage under conditions of a high imposed strain rate at low temperatures). It is particularly interesting to study these effects in a solid which shows a spectrum of behavior ranging from fully ductile to semi-brittle behavior. Such a solid is silver chloride whose mechanical behavior depends sensitively upon temperature and strain rate.'," The present paper is concerned with a study of the influence of inclusions (in the form of alumina particles) on the fracture behavior of silver chloride loaded uniaxially at low strain rates at room temper- ature and also under notch impact conditions over a wide range of temperature. In particular, it will be shown that the alumina particles can exert a startling effect on the ductile-brittle transition temperature of notched silver chloride and that the magnitude and nature of the effect depends upon both the quantity of alumina and the shape of the alumina particles. 1. EXPERIMENTAL PROCEDURE 1.1 Materials Used. Silver chloride powder of analytical reagent (AR) quality having an average particle size 6 was supplied by the Mallinckrodt Chemical Works (st. Louis, MO.). Acid washed 900 mesh alumina powder, designated A38-900, was supplied by the Norton Co. (Cambridge, Mass.). This powder was added to silver chloride in two forms: a) the as-received condition in which the individual particles were of random irregular shape; their statistical average size was 7; b) in a condition in which each particle was spherically shaped by a fusion technique. In this case, the statistical average particle size determined with the optical microscope was approximately the same (about 5p) but electron micrographic evidence indicated that many ultra fine particles were present in the spheroidized powder. 1.2 Preparation of Composite Materials. Silver chloride-alumina composites containing 2.5, 5, and 15 pct by volume of alumina were produced by the extrusion of mechanically mixed powders blended in a ball mill for 24 hr at room temperature. The mixtures were compacted at 50,000 psi at room temperature in the form of billets 3/4 in. in diameter and 1 in. long which were then extruded with a 16:l reduction ratio at 370°C through a radius-type steel die having a 5 deg lead-in angle. An extrusion temperature of 370°C was selected to ensure that all composites had sufficient plasticity to be extruded. Apart from this general requirement, the choice was arbitrary. 1.3 Microstructure of Composites. Attempts were made to check the distribution of alumina metallo-graphically by polishing transverse and longitudinal sections of the extruded rod. Specimens were wet-ground to 600 emery paper and lapped successively with 5 and 0.25-p grades of diamond paste. They were etched for 10 sec in 10 pct sodium thiosulfate solution and lightly polished in concentrated ammonium hydroxide. The most effective way to render the alumina particles and grain boundaries visible was to radiate the surface with intense white light to decorate the grain boundaries and the particle-matrix interfaces photolytically.

Jan 1, 1962

By J. Gurland

The strength variation ofWC-Co alloys with composition and particle spacing falls into two ranges. 1) Above a critical value of the mean free path, the strength follows a dispersion hardening relation; it is proportional to the volume fraction of WC and in-versely proportional to the particle size. 2) Below a critical value of the mean free path, the strength variation is based upon the Griffith criterion of fracture and is controlled by the case of crack propagation. The maximum strength is attained when the structure and load just satisfy the critical conditions for spontaneous crack propagation. THE relation between the strength and the structure of cemented carbides is of interest not only for its own sake but also for its contribution to the understanding of composite materials in general. The cemented carbides are essentially aggregates of a brittle carbide constituent and a ductile binder phase and, at certain structures of intermediate composition, the composite alloys attain strengths far higher than those of the separate constituents in bulk. It is this variation of strength with structure which will be discussed. The experimental procedures of sample preparation, mechanical testing, and quantitative metallo-graphic analysis have been described in Ref. 1. The reported strengths are the maximum fiber-stresses in bending calculated on the basis of completely elastic behavior. The plastic contribution to the over-all deformation is small and was neglected in the calculations (the elongation at fracture of the most ductile alloy, 50 pct WC-50 pct Co, is less than 0.5 pct).2 The pertinent structural parameters are: f, the volume fraction of tungsten carbide; p, the mean free path through the binder phase; the contiguity C, defined as the average fraction of surface area shared by a particle of wc with all neighboring particles of the same phase; and d, the average equivalent spherical diameter of the WC particles. The strength variation of WC-Co alloys with composition and particle spacing is shown in Fig. 1 and Table I, which are based partly on previously published data' and partly on new experimental work which extends the range to higher values of the mean free path. Each data point represents the average of five samples. For a given composition, the transverse rupture strength reaches a maximum

Jan 1, 1963

By J. C. Fisher

Martensite transformations in steels and other alloys are characterized in part by the absence of composition changes during the growth of a new phase. Transformation occurs rapidly, and there is insufficient time for long range diffusion or partition of alloying elements to take place; martensite reactions in alloys thus are similar to phase transformations in single component systems. A fundamental understanding of martensite transformations in steels is impossible without knowledge of the free energy change upon transforming austenite (face centered cubic iron containing alloying elements) to ferrite (body centered cubic iron containing alloying elements) of the same chemical composition. The present paper assembles the best information available concerning the influence of temperature and composition on this free energy change. Most of the material has been taken from the work of Johansson,' Mehl and Wells,2 Zener3,4 and Smith;5 and indirectly, through these authors, from the work of Austin.6 In agreement with the generally accepted viewpoint, martensite is assumed to be an ordered solution of carbon in ferrite of the same composition as the parent austenite; only at high temperatures and low carbon concentrations is the carbon in ferrite distributed at random. The properties of the disordered solution are estimated by extrapolating the known properties of iron-carbon solid solutions into the range of supersaturation, and the free energy change associated with ordering is estimated from the theory developed by Zener. By incorporating Smith's recent thermodynamic measurements and Zener's theory of ordering, the present analysis modifies previous estimates of the free energy change associ- ated with martensite transformations. Consider a two component system consisting of a solvent A and a solute B. Let Na and Nb represent mol fractions of A and B respectively, let aa = raNa and ab = YbNb represent activities, and let superscripts 1 and 2 refer to phases 1 and 2. The partial molal free energies of A and B in phases 1 and 2 can be summarized as follows: free energy standard state Fa' - Fao1 = RT In an1 pure A' Fa2 - Fa2 = RT In aa2 pure A2 Fb1 - Fbo = RT In ab1 pure B Fs2 - FB2 = RT In aB2 pure B. The free energy of a gram atom of phase 1 is* AF1 = Na'Fa1 + Nb'Fb1 and that of phase 2 is AF2 = NA2FA2 + NB2Fb2. A martensite transformation from phase 1 to phase 2 requires Na1 = Na2 = Na and NB1 = NB2 = Nb, and the free energy change per gram atom accompanying transformation is AFi-2 = NA(Fa2 - Fa1) + Nb(Fb2 - Fb1) = NA[RT In (aA2/aA1) + AFa1?2] + Nb RT In (aB2/aB1) = Na[RT In (ra2/ra1) + AFa1?2] + Nb RT In (TaVTB1). [1] where yn2, yn1, yB2, yB1 are activity coefficients, and where Ma'+* is the free energy change upon transforming a gram atom of pure A from phase 1 to phase 2 at the temperature in question. For martensite transformations in plain carbon steels, A = iron (Fe), B = carbon (C), 1 = austenite (7). 2 = ferrite (a), and Eq 1 is AFr ?a= NFe[RT In (rf.a/rfer) + AFF.r?a] + TVc RT In (eca/rc1)- L2] Nothing is known concerning the values of yFea and yca for carbon concen- , trations in excess of 0.025 pct. However, the approximation rf.7 = 7f." = 1 cannot be appreciably in error for small carbon concentrations, and Eq 2 reduces to Afr-a = NfeFfer?a1 + NC RT In (rca/rcr)- [3] Johanssonl and Zenera have calculated MFfr?a from the specific heat measurements compiled by Austin.6* Their calculated values agree closely, and are summarized in Table 1. The activity coefficients relative to graphite for carbon dissolved in iron vary with temperature according to the relationships d In rcr/d(1/T) = AHcr-R dlnyca/d(l/T) = AHCa/R where AHc? and AHca are the heats of solution of graphite in y and a iron. Assuming the values of AH to be independent of carbon concentration and temperature, In rCr = AHcr/RT + I1 In rca = AHCa/RT + 12

Jan 1, 1950

By L. Kaufman

An equation is derived relating AF a", the difference in free energy between austenite and martensite, to temperature and composition in the iron-chrmnium and iron-chromium -nickel systems. This equation is used to calculate at M,for low-carbon stainless steels. A method for utilizing the energetic equations to calculate M, in stainless steels is suggested. In addition, an explanation is given for the anomalous effect of chromium in forming a y loop concurrent with the lowering of M, in iron-base alloys. It has been demonstrated that the effect of alloying elements on the Ms temperature is strongly dependent upon the influence of the alloying element on the thermodynamic properties of the y and a phases. Notwithstanding the fact that alloying elements affect the Ms temperature by changing the lattice parameters, elastic constants, and inter-facial energies of the a and y phases, their primary role is a thermodynamic one. Thermodynamic analyses have been presented for the iron-carbon'-4 and iron-nickele systems in which equations are derived for Fa and FY, the free energies of the b.c.c. (or b.c.t.) and f.c.c. phases. These equations, which can be obtained with the aid of the equilibrium diagrams, can be used to help predict the Ms vs composition curves. This paper deals with a calculation of the thermodynamic properties necessary to compute AFffLY for iron-chromium alloys. In view of the lack of direct information concerning the activity of chromium in the a and y phases of iron, the regular solution approximationa,g was utilized to bridge the gap. After the necessary equations were derived for the iron-chromium system they were used to calculate AFff— Y for stainless steels by combining them with the previous results obtained for iron-nickel alloys. The results of these calculations offer a means of rationalizing the anomalous behavior of chromium in iron-base alloys. The latter depends on the regular solution approximation in contrast to the explanation offered by zener , which is based upon the "magnetic specific heat effect." THERMODYNAMICS OF THE IRON-CHROMIUM SYSTEM If y represents the atomic fraction of chromium in an iron-chromium alloy, then the free energy of the b.c.c. phase Fa, the f.c.c. phase FY, and the difference in free energy between the f.c.c. and b.c.c. phases of the same composition are given through [3] and Fmy represent the free energies of mixing of the a and y phases; while @era -' and uFea 4Y represent the difference in free energy between f.c.c. and b.c.c. chromium and iron respectively. The values of AEFe0ff4Y in the temperature range between 0" and 900K ( .

Jan 1, 1960

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram for the gadolinium-cobalt system has been determined. Seven intermetallic compounds have been found at compositions corresponding to the follwing gadolinium-cobalt ratios: 3:1, 1:1, 2:3, 1:2, 1:3, 1:4, 1:5. The GdCor compound has a congruent melting point above 1600°C. whereas the remaining compounds melt incongruently. Eutectics exist at 16 wt pct Co and 84 wt pct Co, with melting points of 620° and 1260°C, respectively. PREVIOUS papers'" have recorded constitutional data for systems of gadolinium with iron and nickel. This paper presents data obtained on alloys of gadolinium with the remaining 3d transition element-cobalt. voge13 found that cerium forms, with cobalt, the intermetallic compounds; Ce3Co, CeCo, CeCo2, CeCo3, CeCo4, and CeCo5 Other workers4-' found the 1:2 compound in this series to exist in a C-15 (face-centered cubic) structure and the 1:5 compound to exist in a hexagonal crystal system. Comparison of earlier data with that now reported will be made subsequently. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been previously reported.' The cobalt content of alloy specimens was determined volumetrically. RESULTS Microstructure—The alloy containing 10.5 wt pct Co corresponds closely to the composition of the first intermetallic compound Gd3CO. In Fig. 1 the microstructure is essentially single phase composed of Gd3Co which formed peritectically. The globular areas are remnants of the peritectic reaction which did not quite go to completion. A eutectic occurs between Gd3Co and the next higher compound GdCO, which is followed by a series of peritectic compounds. Fig. 2, an arc-cast alloy containing 20.2 wt pct Co, shows large primary crystals of GdCo etching either white or black (depending on crystallographic orientation), embedded in the eutectic. Similarly, in Fig. 3 at 31.2 wt pct Co, a compound, probably GdCo3, has separated from the melt. Subsequent peritectic reactions were almost completely by-passed as the alloy cooled, the residual liquid freezing as a fine eutectic. In the 47.5 wt pct Co alloy, Fig. 4, the high melting point compound, GdCO4, has solidified as massive, white-etching grains, which reacted with the liquid to form GdCo3 as the second phase. The microstructure of an arc-melted alloy containing 60.5 pct Co is complex, Fig. 5, and presents some difficulty in interpretation. The grey etching matrix is probably primary GdCO4. The dappled phase represents grains of GdCO5 which have separated from the melt on cooling. The discrete spots in this phase are eutectic liquid. Small light etching crystallites are probably GdCO5 formed by the incomplete high-temperature peritectic reaction. GdCO4 is retained in arc-melted specimens containing 70.5 wt pct Co, Fig. 6. White areas of this compound are held in a matrix of GdCO5 the appearance of which is mottled slightly by inclusions of the second eutectic in this system. The development of the spheroidized eutectic at high cobalt contents is depicted in Fig. 7 (80.3 wt pct Co) in which the white massive crystals are GdCO5 compound. Further development of this eutectic is seen in Fig. 8, the primary white phase here being pure cobalt. Thermal Studies—Differential thermal analyses and melting point determinations have yielded the data shown in Fig. 10. The high gadolinium eutectic, indicated by microscopy, was confirmed at about 16 wt pct Co, melting at 620°C . A eutectic also occurs at about 84 wt pct Co melting at about 1260°C. The thermal arrests at 8803 960°, 1060; and 1210°C,

Jan 1, 1962

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined in part for the sgstem Gd-Fe. Seven intermetallic compounds have been found at compositions corresponding to the following Gd-Fe ratios; 2:3, 1.2, 1:3, 2:7, 1:4, 1:5, and 2:17. The GdFe, com-pound has a congruent melting point above 18000C, whereas all of the remaining compounds melt incongruently, A eutectic exists at 13 wt pct Fe at a temperature of 860°C. ALTHOUGH an increasing amount of information is becoming available on the metallurgy of pure rare earth metals, relatively few studies have been made on alloy systems of the rare earths with the transition metals; iron, nickel, and cobalt. Even less data are extant on gadolinium alloys although it could be expected that such alloys might possess interesting structural and magnetic properties. In this paper, we report investigation of the gadolinium-iron alloy system. Studies on systems containing nickel and cobalt will be presented in subsequent papers. Previous data on gadolinium-iron compounds have been reported by Endter and Klemm1 and Jep-son and Duwez.2 Both reports agree on the existence of the GdFe2 phase, which crystallizes with the C-15type structure (face-centered cubic). This is in accord with results of the present work. EXPERIMENTAL The gadolinium metal used was prepared by met-allothermic reduction of high purity gadolinium fluoride. A typical analysis of the metal thus produced indicated the principal impurities to be oxygen, 0.24 pct, and tantalum, 0.2 pct. The iron metal used for alloying was a reagent grade material. Alloys were prepared by arc melting mixtures of the respective metals. Appropriate quantities of the two component metals were carefully weighed, blended and compacted. The compacts were then melted in an arc furnace consisting of a water-cooled copper hearth plate and a water-cooled tungsten-tipped counter electrode contained in a brass vacuum chamber. The furnace was evacuated to an absolute pressure of less than 1 with the leak rate established as being less than 20 per min. The furnace was then back-filled to a pressure of 25 mm of Hg, with a 75 pct He-25 pct Ar mixture. Arc melting at 25 v and 300 amp was maintained for about 30 to 60 sec until the entire visible area of the sample became molten, by which time surface tension had drawn the molten metal pool into a large bead. After allowing the furnace to cool, the alloy button was inverted and the melting process repeated. A series of melts was made covering entire composition ranges from 100 pct Gd to 100 pct Fe. All samples were examined metallographically in the as-melted condition. As the phase diagram became rationalized, and differential thermal analysis had given indications of temperature arrests, annealing was carried out in vacuo or in argon. Generally, compositions containing more than about 60 pct Gd were heat treated at 750°C and alloys containing less than this quantity of gadolinium were annealed at 1000°C. Prolonged annealing times were of the order of 100 to 200 hr. Metallographic examination was repeated on the annealed materials. Although little material loss was noted during alloy preparation, chemical analyses were made on all specimens prepared. The following standard, analytical techniques were used. Samples were dissolved in hydrochloric acid; insoluble material was filtered off, ignited and fused with potassium pyro-sulfate. The cold melt was leached with dilute acid and the solution thus obtained added to the main sample solution. Gadolinium was always determined gravimetri-callv as oxide from oxalate ignition. Iron was removed from an aliquot sample by electrolysis on a mercury cathode at approximately six volts. Gadolinium in the iron-free electrolyte was then precipitated as oxalate which was subsequently ignited to oxide. Iron was determined volumetrically in an aliquot solution by reduction with stannous chloride fol-

Jan 1, 1962

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram has been determined for the system gadolinium-nickel. Nine intermetallic compounds have been found at compositions corresponding to the following gadolinium-nickel ratios: 3:1, 3:2, 1:1, 1:2, 1:3, 2:7, 1:4, 1:5, 2:17. The GdNi and GdNi5 compounds have congruent melting points of 1300' and 1500°C, respectively while the remaining compounds melt in-congruently. Eutectics exist at 15 wt pct Ni, 31 1/2 wt pct Ni and 87 wt pct Ni with melting points of 6703 8803 and 1220°C, respectively. IN a continuing investigation of the properties of rare earth alloys, a study has been made of the gadolinium-nickel system. Previous work encompassed the iron containing alloys and a subsequent paper will deal with the constitution of the gadolinium-cobalt system. Vogel,1 examined alloys of nickel with lanthanum and cerium. R3Ni, RNi, RNi2, RNi3, RNi4, and RNi5 compounds were found. Endter and Klemm,2 Fulling et al.3 Heumann,4 and Nowotny5 found the 1:2 compositions of this series to exist in a C-15 (face-centered cubic) structure, and the 1:5 compositions in a hexagonal system. Jepson and Duwez6 more recently examined these 1:2 and 1:5 compositions and generally confirmed earlier data while Wernick and Geller7 most recently have given additional data on the GdNi5 compound. Comparisons with our results will be made in the appropriate section of this report. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been given in our earlier paper.8 Chemical analyses of the alloy samples were made by dissolving the specimen in nitric acid, precipitating the gadolinium as hydroxide and the nickel with dimethylglyoxime. Both precipitates were ignited to oxide and weighed. RESULTS Microstructure— Metallography of alloy specimens in this series has been conducted on both arc-melted and annealed materials. Etchants used have been 5 pct nital with approximately 10 pct distilled water added, for high gadolinium samples; Carapella's ferric chloride solution for intermediate compositions; and Marble's (copper sulfate) reagent for high nickel content alloys. Because of difficulties encountered in the grinding and polishing of specimens containing 40 to 75 wt pct Ni, no photomicrographs were made of such specimens. The microstructure of an arc-melted 5.3 wt pct Ni alloy is shown in Fig. 1. Light etching primary grains of gadolinium are embedded in an eutectic matrix. The microstructure of an alloy of 9.55 wt pct Ni alloy, Fig. 2, annealed 50 hr at 700°C, consists almost entirely of the intermetallic compound Gd3Ni. The structure of an arc metal alloy of approximately 19 pct Ni, Fig. 3, consists of grains of the compound GdNi embedded in the Gd3Ni2-Gd3Ni eutectic. The arc-cast structure of the 38.7 wt pct Ni alloy is shown in Fig. 4. Large primary grains of a compound rest in a matrix structure of coarse GdNi-GdNiz eutectic. Because of the occurrence of several peritectic compounds in the central region of the diagram, identification of the primary structure in this alloy is not certain. As has been indicated above, microstructures of alloy specimens containing between ca 40 and 75 wt pct Ni have not been photographed. These specimens were highly brittle, and macro- and micro-cracking were impossible to control in the grinding and polishing procedures. Prolonged annealing did not alleviate this condition. Visual observations in small specimens did, however, provide evidence for a multiplicity of phases and peritectic dissociations of compounds although rationalization of structures was not possible.

Jan 1, 1962

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.' The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By W. A. Tiller, J. P. McHugh

THE phase diagram of the Ge-Te system was first investigated by Klemm and Frischmuth.' They arrived at the phase diagram shown in Fig. 1 indicating the presence of a peritectic phase boundary at the 50 at. pct Ge composition. Later, Schubert and Fricke2 obtained data which suggested to them the possible existence of a eutectic at about 55 at. pct Ge. In order to resolve these differences, we have carefully studied this system in the region 40 to 60 at. pct Ge using both the conventional thermal analysis technique and a new solidification technique.3y4 The alloys were prepared from semiconductor grade germanium and 99.999+ Te by reacting the elements in evacuated, graphite coated, vycor tubes. The samples were placed in a thermal analysis apparatus described elsewhere4 and cooling curves were taken of each alloy to determine the liquidus surface. The cooling curve for a 50 at. pct alloy shows two distinct arrests about 1°C apart which

Jan 1, 1961

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs' adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

By C. J. Osborn

The temperature dependence of the free energies of formation of metallurgically important oxides, sulphides, chlorides, carbonates and sulphates is presented graphically, whereby the task of deriving practical metallurgical information is greatly simplified. The diagrams have been revised according to the latest available thermodynamic data. WHILE it is true that much careful investiga-tional work remains to be done, there are already available in the literature sufficient thermo-dynamic data to enable the metallurgist to predict with reasonable confidence the equilibrium conditions to be expected in most important, and potentially important, metallurgical reactions. In this connection, the careful, critical compilations of K. K. Kelley and his collaborators in numerous U. S. Bureau of Mines Bulletins are particularly valuable. However, the translation of reliable thermo-dynamic data into metallurgical language unfortunately involves lengthy manipulations of the cumbersome formulas which can be set up from heat of formation, entropy, and heat capacity data. Many years ago, Kelley20 predicted that thermo-dynamic calculations would be made in the future "with the aid of free energy, heat content, and entropy tables, rather than by means of the algebraic methods employed at present", and where such tables are available they greatly simplify the task of deriving practical metallurgical information. However, in addition to these tables, there are also available one or two reliable graphical presentations, particularly of free energy data, which may be used in the same way as the tables, but which have the added advantages that interpolation is never necessary, and that the behavior of different metals or compounds may be compared at a glance. Some years ago Professor Robert Lepsoe, Head of the Department of Metallurgy at Norways Institute of Technology (N.T.H.), began a compilation of curves showing the temperature dependence of the heat contents of the elements, and the heat contents and heats and free energies of formation of the common metallurgical compounds. With such a compilation, the thermal and free energy requirements of a reaction may be read from curves in a matter of seconds; and this statement applies not only to the formation of compounds from their elements, and to the reverse dissociation, but to any reaction involving substances whose thermodynamic properties are available. This follows from the fact that heats and free energies of formation are completely additive. For example, the free energy change associated with the chlorination of a metallic oxide at any temperature, T, is given by the free energy of formation of the chloride at temperature T minus that of the oxide also at T; both of these quantities may be read directly from curves of the type suggested above. Since this early, unpublished work of Lepsoe, both Ellingham7 and Richardson and Jeffes46 have

Jan 1, 1951

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By R. W. Heckel

The growth and shrinkage rates of second-phase particles of various size distributions are analyzed in terms of five mathematical models. These models apply to various forms of diffusion-controlled growth (one model) and interjace-controlled growth (four models). The expression for diffusion-controlled growth assumes local equilibrium at the interface between the second Phase and the matrix and through the choice of the proper flux area perrnits the definition of minimum diffusion-controlled growth kinetics. The interface-controlled kinetics models consider the situations where the rate-controlling step occurs at either the interlace undergoing solution or the interface undergoing deposition. In addition, each of these interface-controlled kinetics models is analyzed for interface reaction rates which are independent of the thermodynamic activity gradient across the interface or proportional to the gradient. THE variation of the size distribution of second-phase particles in a solute-saturated matrix has been a stimulating topic for many years. Research has been carried out in this area for situations where the matrix was either liquid or solid. It is well-understood that the over-all process results in an increase in the average particle size, a decrease in the total number of particles per unit volume, and a net decrease in surface area. Greenwood1 has presented a mathematical model based upon the mass balance existing between growing and shrinking particles. His analysis is stated in terms of Fick's First Law using concentration gradients set up between particles of different size as a result of the effect of surface curvature on solubility. Greenwood's analysis indicates that the mean particle size should increase approximately as the cube root of time. Asimow2 has shown that several of the simplifying assumptions employed by Greenwood may be eliminated from this diffusion-controlled model with little increase in complexity. Lifshits and Slyozov3-5 have also considered the growth-shrinkage problem involving diffusion-controlled kinetics. Their analysis was extended to include the effects of interacting particles ("kinetic approximation"), particle shape, and elastic strains. These authors also show that the mean particle size varies as the cube root of the reaction time. wagner6 has formulated expressions for both diffusion-controlled kinetics and interface-controlled kinetics in the growth-shrinkage problem. Wagner's diffusion-controlled kinetics is based upon the same form of mass balance using Fick's First Law as used by others and is shown to be applicable to situations where kr >> D (k is the interface reaction constant, r is the particle radius, and D is the diffusion coefficient). This analysis also yields a mean particle size which varies as the cube root of time, in agreement with other workers. Wagner also developed interface-controlled kinetics to handle kr « D. This model was based upon the fact that the interface reaction rate is proportional to the interface area. Wagner assumed that the rate was also proportional to the thermodynamic activity difference, ?a, existing across the interface. Thus, the specific reaction rate at the surface of radius r was defined as k • 4nr2 . ?a. It is the purpose of the present paper to reconsider the processes of diffusion-controlled growth and interface-controlled growth in the variation of particle-size distributions as a function of time at constant second-phase volume. The analyses are formulated in a manner which permits data obtained

Jan 1, 1965

By R. W. Heckel, R. L. DeGregorio

The DeHoff method of determining the size distribution of ellipsoid-shaped, second-phase particles has been applied to the spheroidization of cementite in a eutectoid steel. The surface area of Precipitates determined from the various size fractions in the distribution was correlated with surface-area measurements based on the number of intersected interfaces on a random lest line. The precipitate particles were found to be oblate ellipsoids with an axial ratio of about 0.90. The size distributions were found to be log-normal. A method is proposed whereby the shrinkage of small particles and growth of large ones can be determined from the experimental data. The experimental data are compared to previously proposed mathematical models describing diffusion-controlled kinetics and various types of interface-controlled kinetics. The experimental growth and shrinkage rates are considerably slower than those predicted by diffusion-controlled kinetics. The best fit is obtained for a model describing interface-controlled kinetics limited by the rate of formation of cementite at the growing interfaces where the interfacial reaction rate is proportional to the solute thermodynamic activity gradient across the surface. THE subject of spheroidization of second-phase particles has been considered previously by other investigators. Livingston1 has studied the precipitation of the cobalt-rich phase from copper alloys containing 0.7 to 3.2 wt pet Co. His results indicate that the average particle size increases as the cube root of the heat treatment time in accord with diffusion-controlled kinetics.'-' Komatsu and rant' in their studies of the growth of SiO2 in a dispersion-strengthened copper-silica alloy found that the initial growth of SiO2 proceeded by diffusion-controlled growth and later stages were limited by interface-controlled growth. The values of the activation energy obtained for the interface- controlled process led them to the conclusion that the process was limited by the dissociation of SiO2 at the shrinking interface. The transition from diffusion-controlled growth to interface-controlled growth was characterized by a particle size which varied with the heat-treatment temperature. It is also interesting to note that the particle-size distribution as found by Komatsu and Grant exhibits log-normal behavior when replotted on log-probability coordinates. Dromsky, Lenel, and Ansell9 have observed the growth of Al2O3 particles having a mean free path of about 1.5 to 13 µ. Their photomicrographs indicate that the Al2O3 particle sizes were larger than those observed by Komatsu and Grant. Dromsky, Lenel, and Ansell concluded that the Al2O3 coarsened by an interface-controlled growth mechanism limited by the solution of A12O3 at the shrinking interfaces. Bannyh, Modin, and Modin10 have studied the spheroidization of a eutectoid steel (0.83 wt pet C). Their spheroidization (tempering) treatments were carried out in the range from 210o to 700°C for times between 1.5 sec and 20 hr. Measurements of mean particle size as a function of time indicated a cube root of time dependence of size at 700°C, in agreement with previous analyses of diffusion-controlled kinetics.2°7 At lower temperatures, the time dependence was less than the one-third power. It is important to note that, although mathematical models of growth* considering particle-size distribution have been available, measurements of only mean particle size have been carried out. DeHoff11 has presented a quantitative metallography technique which is applicable to the determination of the size distribution of ellipsoids of constant shape. This method is applicable to both oblate and prolate ellipsoids of all ratios of minor to major axis and is based upon an extension of Saltykov's analysis12 of the distribution of spheres of varying size. DeHoff's analysis is based upon measurements of the minor axis of the particles on a random plane of polish in a unit area. This method provides a measure of the number of ellipsoids in various size ranges per unit area. As pointed out by DeHoff, such measurements may be used to obtain surface area and total precipitate volume data. Thus, the accuracy of the distribution analysis may be checked by comparison of the surface and volume

Jan 1, 1965

By A. E. Nehrenberg

THE mechanism by which austenite forms in steels has received a great deal of attention in the literature in past years.'-'* Our present knowledge concerning this mechanism has been recently summarized quite concisely by Bain and Vilella,1 while a few years ago the literature was carefully reviewed by Roberts and Mehl.² The consensus is that any ferrite-carbide interface is a potential site for the nucleation of austenite during heating above the Acl temperature, and that the new austenite generally grows freely to produce approximately equiaxed grains, whether the carbides are initially present in the lamellar or the spheroidal form. In the case of eutectoid steels, growth of the new grains of austenite continues until contact is established with other grains. Then growth stops and an initial austenite grain size is established which does not change until the heating is continued to some high temperature at which grain coarsening begins. In the case of pearlitic steels which are not of eutectoid composition, the proeutectoid ferrite or carbide may interfere with the growth of the austenite if the temperature is not above that designated the A63 or the Acm, respectively. Although a large amount of work has been done to establish the mechanism of austenite formation in steels, it became clear to the present author while he was studying the transformation characteristics of a new 0.25 C Mn-Si-Ni-Mo hypoeutectoid steel" that the manner in which austenite grows in steels depends upon some factor, or factors, not previously considered. This was indicated by the fact that when this steel in the spheroidized condition was heated above the Ae1 temperature the new austenite which was formed did not envelop the carbides and grow in an equiaxed manner as described by Bain³ or spheroidized steels. Instead, in this steel, the austenite was observed to grow much more readily in certain directions than in others with the result that at temperatures within the Ac1-Ac³ ransformation range the austenite grains were acicular in shape. The excess ferrite was also found to be acicular with the distribution of these phases being such that a lamellar pattern was developed. This unusual directional growth of austenite in this new steel initially in the spheroidized condition is illustrated by fig. 1. A search of the literature revealed that this type of growth was not necessarily peculiar to this steel for similar microstructures had been observed by other investigators.4-8 However, the full significance of these microstructures does not appear to have been appreciated, and no work has been done to determine the conditions responsible for this directional growth of austenite or to arrive at an understanding of it. It was for this purpose that the work described in the present paper was carried out. Material: During the course of this investigation a total of 15 steels was studied. They consisted of hypoeutectoid, eutectoid and hypereutectoid carbon steels, and hypoeutectoid and hypereutectoid alloy steels, all of which were obtained in the annealed condition from commercial warehouse stock. As received, the carbon and alloy hypereutectoid steels had microstructures which consisted of spheroidal carbides in ferrite, whereas the eutectoid steel and the hypoeutectoid steels were pearlitic. The grades of steel represented were 1050, 1080, 10110, 3310, 4140, 4340, 4615, 6145, 8620, 9260, 9442,

Jan 1, 1951

By A. E. Nehrenberg

R. A. Schmucker, Jr.—The writer wishes to point out that an acicular growth of austenite, similar to that described in the author's paper, was recently observed in an alloy steel of only 0.06 C content. This steel, which represents an 0.07 max C, 1.35 Cr, 0.55 Ni, 0.20 Mo analysis, combines the characteristics of minimum hardness in the annealed condition with maximum hardenability and is therefore suited primarily for cold-hobbing applications. The acicular austenite formation in this steel was observed accidentally during a determination of its Ac1 temperature. The samples used in this investigation represented as-forged bar stock which had been given a preliminary temper at 1300°F. The critical (Ac1) temperature was finally established at 1400 °F. Fig. 15 represents the microstructure of the sample which had been heated at 1450°F for ½ hr, water quenched, and tempered at 600°F for ½ hr (for the purpose of darkening the martensite). It will be observed from the distribution of the darkened areas of martensite that the parent austenite grains formed at 1450°F had grown in an acicular manner and still occupied only a small percentage of the total area. The remainder of the area contains the original equiaxed ferrite grains in which new austenite had as yet scarcely formed. However, the tiny isolated martensitic patches at several points where three or more ferrite grains intersect indicate that small austenite grains had formed and started to grow in an apparently equiaxed fashion. Fig. 16 represents the prior microstructure of an original sample in the as-forged and tempered condition, before it was heated -above the critical temperature. It is probable that there are two kinds of ferrite in this structure: (1) The equiaxed proeutectoid ferrite grains which separated from the austenite when the steel was cooled from the forging temperature, and (2) the acicular ferrite associated with the aggregate of fine carbide which is represented by the patches of

Jan 1, 1951

By J. D. Grozier, W. W. Mullins, H. W. Paxton

The morphology of the nucleation and growth of austenite into high-purity iron in NH3-H2, gas mixtzires has been studied. The growth rate of an austenitic rim (planar interface) from scratched surfaces of- polycrystalline iron specimens was determined as a function of temperature and percent NH3 and found to he in reasonahle agreement with growth-rate calculations based on a model which assumes the diffusion of nitrogen to he the rate-controlling step. Under certain conditions, austenite pew as platelets; growth rates of these along the surface of single crystals were found to he dependent on surface preparation, orientation, THE development of microstructures can conveniently be thought of in terms of nucleation and growth. The complex topic of nucleation in solid-solid transformations will not be discussed at length, although a few qualitative experiments were performed. Growth is determined by the mobility of the various possible interfaces under the available driving forces in a particular situation. In homophase transformations, it has been clearly demonstrated that the mobility is very sensitive to small amounts of impurities, to the kind of impurity, and to the orientation relations across the boundary.' A degree of quantitative knowledge has temperature and percent NH3. On electropolished surfaces with a (110) pole, the maximum growth rate of platelets was determined and found to be in agreement within a factor of 2 to 3 with theoretical calculations of the edgewise growth rate of a platelet. The calculations are based on a model which assumes that the diffusion of nitrogen in the ferrite in front of the moving curved attstenitic interface at the tip of the platelet is the rate-controlling step. The growth direction on the surface of the single crystal and resztlting habit plane of the platelets were determined and found not to he unique but to vary systematically with the pole of the surface. been obtained. In the case of heterophase transformations, which are significantly more complicated to treat, a comparison of theoretical and experimental studies often shows rather poor agreement.'-' The main purpose of the experiments discussed below was to obtain additional quantitative data on crystallographic effects on boundary mobility in a system which was otherwise as simple as possible, viz. the growth of iron-nitrogen austenite into fer-rite. In the course of the experiments, it became necessary to re-examine the theory for the growth of Widmanstatten plates, especially the influence of anisotropic interfacial free energy. Some other minor experiments in the Fe-N system were performed, and are described briefly. EXPERIMENTAL METHODS A) Material Preparation. The floating zone purified iron used for this investigation was supplied by Battelle Memorial Institute. The nominal composi-

Jan 1, 1965

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn's for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962