Search Documents

By Ghislain Bournival, Seher Ata, Graeme J. Jameson

A common method to prevent bubbles from coalescing in a flotation cell is by the addition of surfactants, called frothers. The gas dispersion properties in a column were tested for solutions of 1-pentanol, tri(propylene glycol) methyl ether, and poly(propylene glycol) in the presence of sodium chloride. The dependency of surfactant on the gas holdup can be divided into regions. It seemed that for a sufficiently low concentration of surfactant, even a stronger surfactant could show a transition in gas holdup from constant/decreasing to increasing with concentration. This region, however, was not marked by a decrease in the average bubble size. In addition, PPG gave higher gas holdup values while averaging larger bubbles. On the other hand, sodium chloride mostly affected the gas holdup when the concentration was high enough to prevent bubble coalescence. Another parameter affecting the gas holdup was the superficial gas velocity. A linear dependency was found between the two under a bubbly flow regime. The current study showed that both surfactants and salt could slightly affect the influence of the superficial gas velocity on the gas holdup.

Jan 1, 2014

By F. Golestani-Fard, A. A. Nourbakhsh

In this paper microstructural development of nitride-Bonded SIC refractories is reported in presence of Al203, Mg() and Urea additives .The samples were prepared by mixing, shaping and firing at 1400-1500°c in a controlled atmosphere furnace. Phase analysis, microscopic observation and mechanical evaluation were taken for microstructural investigations. The strength of samples doped with Al203 was first increased and then decreased at higher amount of Al2O3 additions. The addition of MgO decreased the strength while the urea showed an improving effect on strength. These phenomena could be attributed to microstructural evolution and mainly to liquid phase formation and grain morphology. It was found that the additives such as Al203, MO and urea could modify the microstructure in terms of phase formation and texture modification, which in terms influences the mechanical behavior.

Jan 1, 2004

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive, and it is quantified as a confined or unconfined velocity. The confined velocity is more significant as explosives are usually used under a definite degree of confinement. This study evaluates the stepwise increment of the air-deck volume from 10 to 30 percent, and its effect on the VOD. The VOD estimation in the 172-mm-diameter explosive column was conducted using the Dáutriche technique. The air-deck volume increment has an attenuation effect on the steady-state VOD, and detonation failure is high at 30 percent air-deck volume. This attenuation effect is directly linked to the explosive’s rating and efficacy. The air-decking approach in this study is different from conventional air-decking techniques in that it does not employ the fixed blasthole parameters, air-deck volume and specific VOD. 

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Robert S. Ondrey, Robert A. Haney, Kenneth G. Fields

As part of an MSHA program to assess the effectiveness of dust control parameters for longwall mining operations, respirable dust studies were conducted on six longwall sections. The purpose of these studies was to evaluate the influence of airflow and production on longwall dust control. The sections were sampled for 3 to 35 shifts. In addition to dust, ventilation and production measurements, other dust control and operational parameters were measured. The water spray system at each operation conformed with generally recommended practices. Therefore, improvements to the dust control system would be most appropriately achieved through improvements to ventilation along the face. Two methods of assessing the influence of ventilation and production were used. For two of the six mines where extensive sampling (22 and 35 shifts) was conducted, multiple linear regressions were used to relate the dust concentration versus airflow and production data. For these two mines, statistically significant correlations existed between concentration and both production and airflow. The multiple regressions fit to the data indicated that for every 0.47 m3/s (1,000 cfm) increase in airflow, there would be approximately 0.04 to 0.07 mg/m3 reduction in dust concentration; and, for every 1,000 ton increase in production, there would be approximately 0.15 to 0.50 mg/m3 increase in dust concentration. For the four mines with limited data (3 to 10 shifts), as well as for the two mines with extensive sampling, an average ratio of airflow per ton of coal mined was calculated by proportioning the airflow to production and the designated occupation personal respirable dust exposure to a 2.0 mg/m3 concentration. The airflow-to-tons ratio required to maintain a 2.0 mg/m3 dust concentration ranged from 0.0038 0.0071 m3/s per ton (8 to 15 cfm/ton). Both of these data treatments were used to calculate airflow requirements based on normal production rates. For the two mines where both the regression and airflow-to-tons ratio were calculated, results from the two methods agreed within 25 percent.

Jan 1, 1993

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study was to investigate the influence of amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and organic acids (citric, malic, tartaric, fumaric, oxalic, succinic and ascorbic acid) on gold extraction from silicate ore. Use of amino acids to extract gold was preferred compared with organic acids due to the presence of carboxylic group and amine groups in amino acids. Among the assessed amino acids, aspartic acid and glutamic acid had higher capacities to extract gold due to their structures, which lacked aromatic rings and long side chains. Organic acids could also extract gold. In particular, oxalic and succinic acids had the greatest capacity to extract gold versus the other tested organic acids. Moreover, aspartic acid had a greater capacity to extract gold from ores than the same concentration of succinic acid. We confirmed the aspartic acid and succinic acid functional groups by Fourier transform infrared spectroscopy. The findings revealed that aspartic acid had a greater capacity to extract gold than succinic acid due to the presence of both amine and carboxylic groups (succinic acid contained only a carboxylic group). The optimal gold:aspartic acid molar ratio was 1:6 and low concentrations of aspartic acid extracted 35–42%of gold from silicate ore within 15 days. This can be used as an alternative to traditional methods for extracting gold from ore; it is non-toxic to human health and environmentally friendly.

Aug 10, 2021

By PAITIP THIRAVETYAN, KANJANA KUDPENG

The aim of this study is to compare amino acids and organic acids in the extraction of gold from silicate ore. Amino acids were found to have higher efficiency of gold extraction than organic acids at the same acid concentration, which is likely due to amino acids having both carboxylic and amine groups in their structure, while organic acids only have carboxylic groups. Five amino acids (glycine, aspartic acid, glutamic acid, lysine and tryptophan) and seven organic acids (citric, malic, tataric, fumaric, oxalic, succinic and ascorbic acids) were selected to investigate gold extraction efficiency. Aspartic acid was found to have greater capacity to extract gold than succinic acid. The optimal gold to aspartic acid molar ratio was 1:6, and low concentrations of aspartic acid extracted 35 to 42 percent of gold from silicate ore within 15 days. Further studies are needed to increase gold leaching and reduce incubation time. The results imply that aspartic acid can be used as an alternative reagent to traditional methods for extracting gold from ore. This method is nontoxic to humans, is environmentally friendly and can have real applications.

By Takeshi Yoshikawa

For the sake of effective control of titanium-compound inclusions in the steel-making processes, especially for stainless steel production, the influences of alloying elements of chromium, nickel, manganese, molybdenum, copper and oxygen on the thermodynamic property of titanium in molten iron were investigated at 1873K. At a certain titanium potential controlled by the coexistence of Ti3O5 and Ti2O3 doubly saturation of steels, the interaction parameters between alloying elements and titanium in molten iron were determined as follows. [ ] From the investigations on the equilibrium of titanium deoxidation in molten iron, the activity coefficient of titanium and the first order interaction parameter between oxygen and titanium were determined as follows. [ ] Also, deoxidation equilibrium for titanium in molten 304 stainless steel was measured and compared with the calculated results using the determined interaction parameters.

Jan 1, 2006

By H. Conrad, K. Jung

"The effect of an external electric field E=5(+) kV/cm applied during the solution heat treatment at 500°-550°C of three commercial Al-Mg-Si alloys (AA6061, AA6022 and AA61l1) on the asquenched resistivity Pw and hardness H.,NULL, w was investigated. It was found that the field gave a significant increase in Pw and in Hv,w, for AA6022 and AA6111, but had no clear effect on AA6061. Thermodynamic analysis gave that the effect of the field on AA6022 and AA6111 was to reduce both the enthalpy ?H, and entropy ?H, of solution. Considering the chemical composition of the three alloys it appears that the influence of the field may depend on the amount of Cu plus excess Si present in the alloy.IntroductionKlypin and Soloviev [1, 2] were the first to report that the application of an external electric field during solution heat treatment (SHT) of Al alloys gave an increase in the as-quenched resistivity and hardness. They attributed these effects of the field to an increase in solubility of the alloying constituents during the SHT. More recently Liu and coworkers [3, 4] also reported an increase in the as-quenched resistivity of Al-Li alloys with application of an electric field during SHT. Further, the present authors [5] found that the application of an electric field during the SHT of the commercial Al-Mg-Si alloys AA6022 and AA61i1 increased their as-quenched resistivity and hardness. Their thermodynamic analysis of the results indicated that the field decreased both the enthalpy ?H, and entropy ?S, of solution."

Jan 1, 2004

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By K. Ihara, R. Akiyoshi, Y. Takaki, S. Kang, H. Shishido

"Tensile tests and scanning electron microscopy-electron backscattered diffraction (SEM-EBSD) analysis were performed in an Al-Mg-Si alloy to clarify the effect of annealing and cold-rolling reduction on the texture formation. The hot-rolled specimens were cold-rolled with the reduction of 58-75%(CR1), followed by annealing at 773 K for 5 min(IA). The secondary cold-rolling(CR2)for the IA specimens with the reduction of 33–66%, followed by the solution heat treatment(ST), were performed. Focusing on the CR1 and CR2 specimens, the average r-values increased with higher primary and lower secondary cold-rolling reduction, respectively. This was considered to be due to the increase of r-values measured in the direction of 45 degree with respect to rolling direction, caused by the formation of the ß-fiber components (Brass {011}<211>, Copper {112}<111> and S {123}<634>) with high density. Based on the texture analysis of annealed specimens it was suggested that the high density of the ß-fiber components after IA and the small amount of stored strain energy of CR2 introduced by the lower cold-rolling reduction remained the ?-fiber components even after solution treatment.INTRODUCTION Al-Mg-Si alloys have been applied to automobile body applications, due to their excellent paint-bake hardening (age-hardening) and corrosion resistance compared to other aluminum alloy. On the other hand, the mechanical properties and deep drawability of Al-Mg-Si alloys are inferior to those of steels. Thus, it is important to improve the mechanical properties and deep drawability in order to expand the application components. One of the best methods to improve the deep drawability is to increase the Lankford coefficient (r-value). Previous studies reported that the increase of the average r-value ( ) improves the deep drawability. The relationship between the r-value and texture of the alloy is also well known. Inoue et al. reported that the ß-fiber components, such as Brass ({011}<211>), Copper ({112}<111>) and S ({123}<634>), increase the r-value measured in the direction of 45o with respect to the rolling direction. r"

Jan 1, 2018

By Lijuan Li, Xin Xia, Junjun Huang, Qijie Zhai, Xiang Jiang

"Some experiments with different temperatures (1173, 1223, and l273K) and different annealing times (3, 4, 5, 6min) were carried out on cold-rolled plate of Fe-36Ni invar alloy. The microstructure and the mechanical properties were observed and tested respectively, and the fracture morphology was observed by SEM. The results show that with increasing of the temperature and the annealing time, the austenite grains gradually grow up accompanied by a small amount of annealing twin crystals, meanwhile, its plasticity and toughness are improved, and it is typical ductile fracture under the condition of tensile failure. After annealed at l223K, the invar alloy has better comprehensive properties than that at the other annealing temperatures, and the grains size is more uniform. Furthermore, when the annealing time is 4min, the invar alloy has the best comprehensive properties.IntroductionAs we known, most metals and alloys expand with increasing temperature. More than one hundred years ago (in 1897), Guillaume observed that Fe-Ni alloy with face-centered cubic (fcc) crystal structure, consisting of36%Ni, showing a very small thermal expansion coefficient below the ferro-to-paramagnetic transition, the thermal expansion coefficient around room temperature( <2 X 1O-6K-1 compared to most metallic materials which have a thermal expansion coefficient of 10-20 X 1O-6K-1) [1,2]. Since then, the subject has attracted many researchers, and various alloys with low thermal expansion coefficients have been developed. These alloys, generally known as ""invar alloys"", are in demand where dimensional changes due to variation in temperature must be minimized and where high stability is required [3, 4]."

Jan 1, 2012

By Katja Reinharter

Arsenic can be found in different sulfidic copper concentrates and residues, which for several years have commonly been used in copper metallurgy, as the “arsenic-free” resources are getting rare. Due to the high toxicity the removal of arsenic in the copper smelting process is a very important topic. The typical chemical slag and sulfur attack on the refractory material is getting enhanced by the presence of arsenic. This work deals with post-mortem investigations of a magnesia-chromite brick and castable used in copper smelting furnaces showing an additional and increased chemical attack by arsenic. The knowledge on the wear behaviour is not only based on a detailed chemical and mineralogical characterization, but also on thermochemical FactSageTM calculations, which are carried out on provided post-mortem samples. Post-mortem investigations on used refractory materials represent an important prerequisite for the product development, as well as for special engineered lining concepts to support our customers.

By F. Chiesa

Forty aluminium A356 castings were poured on a Low Pressure Permanent Mould industrial machine, 500x700mm in platen size. The 152mm wide casting comprised three steps, 25mm, 13mm, 6mm in thickness and a 2.5mm overflow which allowed to assess the thin wall capability of the process. The casting campaign, which produced 40 parts, allowed to test the influence of various production parameters including the time of application of the pressure in the crucible, artificial cooling of the mould and casting rate. The thermal history in the mould was recorded over the 40 cycles, which allowed to construct a reliable thermal model of the mould/casting assembly. The metallurgical quality of castings representative of the various conditions was assessed in the 25mm, 13mm and 6mm plates. This included measuring the level of microporosity, the dendrite fineness (DAS), along with the tensile properties in the T6 condition. The radiographic quality per ASTM E155 was also determined. Modelling filling and solidification allowed to verify the validity of the predictions based on available relationships relating microporosity, secondary dendrite arm spacing (DAS) and local tensile properties (Quality Index, Q) to the local thermal solidification parameters.

Jan 1, 2007

By Alfred Boyles

THE experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of funda-mental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic and in others i produced al marked changes in the size of the graphite flakes. These effects seemed to be III sulphur and manganese present in the material studied. Iron-carbon- respond silicon alloys did same manner as mg cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of FIG. 1.-APPARATUS FOR MELTING UNDER PRESSURE. silicon. The present paper is con- A, inlet for gas. cerned with alloys of lower silicon B, outlet for evacuation. content and describes the structural C, power lead. D thermocouple changes produced by melting in E, plug for access to furnace. various atmospheres at pressures F, crucible. ranging from a partial vacuum up to 300 lb. per sq. inch.

Jan 1, 1939

By Gao K, Wu C, Langley J. M, Waugh B, Farrell K

The dissolution of carbon from carbonaceous materials into molten iron is a key step in various ironmaking operations. For example, in new direct smelting processes, carbon in the form of coal is injected into the molten iron bath, which leads to the dissolution of carbon. In foundry operations, typical recarburizer materials can range from high purity graphite to chars. The dissolution performance of these&quot; materials is critical to the operation and could dictate the efficiency and economics of the process.Dissolution kinetics has been studied by various investigators to explain the influence of melt conditions and carbon type (Sahajwalla et al, 1994; Shigeno, Tokuda, and Ohtani, 1985; Orsten and Oeters; 1988; Ganguly and Reid, 1992; Wright and Taylor, 1993). The influence of melt sulphur content on the dissolution kinetics has been characterised (Sahajwalla et al, 1994), with sulphur retarding the rate of carbon dissolution. The carbon dissolution from different sources is seen to vary significantly even under similar melt conditions. This observation has been explained by investigators on the basis of the varying ash content present in the carbonaceous materials. However, ash content alone cannot account for the variability in dissolution kinetics reported in other studies. One such study is presented below.In a recent study (Sahajwalla et al, 1994), pulverised carbonaceous materials were injected into the molten iron bath and the&quot; dissolution kinetics was established. The dissolution of graphite and glassy carbon, which contain almost 100 per cent carbon, was seen to be significantly different when the molten iron contained sulphur. The influence of melt sulphur content was explained on the basis of different wetting behaviour observed.Importantly, the study showed that even pure carbon sources dissolved at significantly different rates. Hence, their performance could not be explained on the basis of ash content.The key difference between graphite and glassy carbon is in their atomic structure. Graphite is highly ordered whereas glassy carbon has relatively poor ordering in its atomic structure. This study showed that the atomic structure in carbonaceous materials can have a significant effect on their dissolution performance.The focus of the present investigation which stems from the past study described above (Sahajwalla et al, 1994), is to investigate the influence of atomic structure of carbonaceous materials on their dissolution into Fe-C-S melts.The specific objective of this study is to determine the relationship between dissolution kinetics and crystallographic character of carbon sources. In order to accomplish this goal, a range of different materials representing a spectrum of carbon sources have been chosen for the investigation. These materials include brown coal char, two types of Auscarb (A and B), and commercial graphite. Auscarb is prepared by calcining Auscoal at 1000&#176;C. Auscoal is made from chemically cleaned Australian coals (Bowling, Chandler and Waugh, 1990). Part 1 of this paper details the dissolution performance of the materials studied, while Part 11 describes the X-ray diffraction study. The relationship between the atomic structural dimension and dissolution rate constant is discussed in light of the results obtained.

Jan 1, 1996

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar&apos;) when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By P. -É. Boileau, S. Mandapuram, Shiping Ma, S. Rakheja

The absorbed power (PAbs) has been suggested as a better measure of human responses to whole-body vibration, since it relates to the cumulative energy dissipated by the body exposed over a given duration. Moreover, unlike the other measures, the PAbs can adequately account for the intensity of exposure. Although, the vast majority of off-road vehicles impose considerably severe vibration along the horizontal axes, the vast majority of studies on biodynamic response characterization consider only vertical vibration. Only a few studies have reported PAbs responses of the seated human body exposed to horizontal vibration and the major contributing factors [1]. This study aims to characterize the PAbs responses of seated human subjects to horizontal (uncoupled x- and y-axis) vibration as functions of the vibration intensity, subject mass, seat height and the, type of back support. Methods Experiments were conducted using a rigid seat with an adjustable backrest inclination and seat height. The seat was installed on a horizontal vibration simulator and the forces at the seat base and the backrest were measured by three-axis force plates. Two single-axis accelerometers were installed on the seat back and the platform, oriented along the axis of motion. The experiments were performed using three different seat heights (350, 390 and 410 mm), back support conditions (NB- no back support and sitting erect; Wb0- Upper body supported against a vertical back support; and WbA- back supported against an inclined backrest, while sitting relaxed) and three different magnitudes of broad band excitations in the 0.5-10 Hz frequency range (0.25, 0.5 and 1 m/s2 rms acceleration under x-axis and y-axis, applied independently). A total of 8 healthy adult male volunteers with total body mass ranging from 59.4 kg to 92 kg and aged between 21-51 years took part in the experiments. The subjects were seated with their hands in lap, and feet supported on the moving platform for each posture. Each measurement was repeated 2 times, while the data were analysed using a bandwidth of 50 Hz and frequency resolution of 0.0625 Hz. [ ] The data were analyzed to derive the absorbed power characteristics of the body at both seat pan and backrest interfaces, while the coherence among the measured forces and accelerations wer

Jan 6, 2006

By Morland R

Recent influence of backfill stability on stope production in the Copper Mine at Mount Isa Mines Limited is described. Changes to the mining process to improve fill stability are described, including increased focus on fill performance, modifications to extraction techniques, increased fill quality, changes to drill and blast practice, and research into backfill stability. Several case studies are described.

Jan 1, 1995