Search Documents

By Swift J. D

A key parameter affecting the performance of gravity thickeners in hydrometallurgical processing operations is the aggregation state of the feed after the addition of a flocculant. New procedures which measure the settling ratelsize relationship and the size distribution of aggregates in their process liquors have been used to quantify the aggregation state of the feedwell, overflow and underflow streams in a tailings thickener. The data obtained have been related to the thickener's operation and to a change in the flocculant dosage. A comparison is also made between the settling rate/size relationships determined with these new procedures and the mud-line settling rates from cylinder tests.

Jan 1, 1991

By T. M. Ruff

A GPS-based traffic awareness and collision avoidance system has been implemented at mines with long, narrow access roads to help avoid accidents involving two approaching vehicles or vehicles following too close. A simple display in the cab of each outfitted vehicle gives an indication of oncoming traffic and a voice announcement indicates the type of vehicle that is coming as far out as 300 meters. Advanced warning of approaching vehicles is increasing driver awareness, especially around blind corners and in adverse weather such as heavy fog, snow, or rain. Speeding alarms have also been implemented and are especially critical as a vehicle approaches reduced speed areas near single-lane bridges or tight curves. A description of the system, safety improvements seen since its introduction, and implementation challenges will be discussed.

Aug 1, 2013

By K. Awuah-Offei

Energy efficiency has become significant due to cost and environmental considerations. Comminution and material handling have been identified as the two most energy intensive processes in mining. The objective of this work was to evaluate truck-shovel energy efficiency strategies using discrete event modeling. Energy audits and time and motion studies were conducted at a surface coal mine to acquire data. A discrete event simulation model of truck-shovel operations was built in Arena® and validated with the field data. The model was used to evaluate the effect of using a larger shovel, and optimizing truck-shovel matching on fuel efficiency. The results indicate that using a larger excavator increases the fuel efficiency of the operation while optimizing truck-shovel matching does not. However, using a larger shovel will lead to under-utilization of the shovel. This work shows the potential benefits of using discrete event simulation to model energy efficiency of mining operations.

Jan 1, 2012

By P Knights, M S. Kizil

Truck/shovel operations constitute 50 - 60 per cent of the cost of open pit mining operations. Mining companies, therefore, are constantly seeking to close the gap between actual truck/shovel productive capacity and maximum potential truck/shovel capacity. This paper analyses the performance of a mixed truck/shovel fleet in an open cut coal mine in Australia. It analyses operating delays, and proposes a novel graphical means of determining truck-limited or shovel-limited operations. A goal seeking algorithm is advanced in order to maximise truck/shovel match factors (MF) and hence optimise fleet productivity.

Sep 26, 2011

By Z Gao, D Liao, W Sun, S G. Pooley, J Wang, Z Shi, G Jing, S Ren, Q Chen

Yuanjing processing plant is a scheelite and wolframite plant in southern China. Water shortages and recent environmental regulations mean that the plant must reuse the wastewater that comes from the mining operation. This paper describes the efforts to reuse the mining and ore washing wastewater (MOW) in the processing plant. Initial attempts to reuse the MOW in the strong magnetic separation were unsuccessful because the magnetic media pack was seriously fouled by the micro-fine precipitate generated. The focus changed to reuse the MOW in the scheelite flotation circuit, which includes one roughing, one cleaning and three scavenging steps. Laboratory batch tests showed this would likely be successful because using MOW reliably improved the flotation performance in the laboratory tests. Then a 20 day industrial trial was run in the plant. The trial was very successful with the enrichment ratio of WO3 increasing from 17.4 to 23.6, while the recovery remained around 79.2 per cent. The industrial trial was so successful the company immediately adopted the new scheme, which has remained in use ever since. This technical solution not only alleviated serious water shortages, and satisfied environmental regulations but also improved the plant performance.

Aug 24, 2022

By Charles Tkaczuk

Key issues ? Process control is a corporate function implemented locally. ? Security and documentation is mandatory requiring standard practices. ? Publish and communicate activities (do not re-invent the wheel). ? Payback metric system for all projects. ? Partnering with vendors based on experience, expertise and joint R&D. ? Focus on phased process control projects and distribution of costs. ? Integration of services and functions. ? Application of global standards. ? Big picture application thinking.

Apr 1, 2005

By Charles Tkaczuk

Key issues ? No business tool has greater potential to effect change and enhance profitability than process control. ? Successful businesses see process control as an integrated engineered system, designed and built into their business models from day one. ? The integration and use of process control sets the stage for years of compounded returns. ? Has been used for years to optimizing recoveries and minimizing waste. ? However, the mining/ore extraction sector has been slow to adopt integrated process control. What is the problem? ? Most executives and engineers do not clearly understand process control when applied to mining/extraction activities. ? Common approach has been to apply generic process control strategies as a blanket cure all and wait for it to pay off. ? No central focus which results in multiple group involvement, overlap and inconsistent application of questionable technology. ? Considered a low priority until production activities commence. ? Comfort in using brute force mining methods. ? An off-the-shelf integrated under ground mining process control architecture has not until recently been available.

May 1, 2004

By Ing Newton Amegbey, Joseph Afari Idun

Ashanti Goldfields Corporation (Gh) Ltd., the leading gold mining operation in Ghana is embarking on a major rehabilitation and expansion programme to increase gold production. A new southern ventilation district was targeted for this programme, and the ventilation system was to be reviewed in order to cope with increased production. The southern ventilation district was previously ventilated by booster fans. This arrangement was however, inadequate to solve the problem of the need to reduce smoke clearance time of the production areas, and to generally improve the underground ventilation conditions. Fan maintenance costs increased with the number of fans installed in the booster fan arrangement, and the fact that the fans were installed underground made maintenance difficult and took longer time. It became necessary to consider the installation of a new main fan on the surface. This paper gives an overview of the ventilation systems of the southern ventilation district of the mine before and after the new main fan was installed. The field tests carried out on the fan to ensure that it complied with supplier's specifications are described, and the new system analysed to see it's effectiveness.

Jan 1, 1993

By Georges Croisé, Les-Lee Thompson, Adrien Debergé

Membrane filtration systems have regained focus in recent years as an effective means of liquid-liquid separation to increase the concentration of valuable elements, recover reagents or remove impurities. ORANO Mining (formerly AREVA) investigated this cost optimization process opportunity as early as 2011 for implementation at the Trekkopje project (Namibia). The key focus was to separate and recycle bicarbonate from the uranium bearing eluate solution. The performance targets were successfully achieved at lab- and pilot scale with an ultrafiltration and nano-filtration configuration system. Early 2015, ORANO Mining further launched an investigation into the use of membranes for acid recycling at the KATCO In Situ recovery mine in Kazakhstan based on the favorable results from the original bicarbonate application. KATCO is the world leader in ISR uranium mining with an eluate processing capacity of 80 000 m3/yr. This site consists of two processing plants namely, Muyumkum and Tortkuduk, located 40 kilometers apart, both operating under acidic conditions whereas precipitation and packaging are based in Tortkuduk only. This paper serves to present the results from the integration of a nano-filtration system at the Muyumkum satellite processing plant. The project consisted of screening laboratory bench studies conducted at ORANO-CIME followed by process validation at KATCO through further bench and pilot test work. The feasibility study assessments were successfully concluded which led to the implementation at an industrial scale in Muyumkum of a nano-filtration process to reduce eluate volumes being sent to the uranium precipitation section whilst achieving effective separation of uranium from sulfuric acid. Nano-filtration technology has drawn significant attention due to the efficiency and reproducibility of the process and its moderate capital cost relative to operational savings. The reliability of the previous results is a great opportunity to reduce operative expenditures within ORANO’s next ISR mining project in Mongolia.

Jan 1, 2020

By J. Alderman

In modern industry, cost and productivity concerns and environmental concerns are sometimes incompatible, but at other times only appear to be incompatible. Surface disposal of wastes from coal preparation plants appears to be an area of the production system with little opportunity for initiating measures which cut costs and concurrently benefit the environment. However, improving the recovery efficiency of fine coal circuitry can cost-effectively reduce the plant waste environmental burden by a substantial amount. Studies at Jim Walter Resources indicate that fine-coal waste measuring 50% ash contains over 50% recoverable, marketable coal. Modifications to the plant circuitry which reduce the amount of misplaced coal in the fine-coal waste stream could substantially reduce the volume of fine waste disposed aboveground. Studies at Jim Walter Resources indicated that episodic overloads of the vacuum filters in the fine-coal circuits at the preparation plants were a source of misplaced coal in the fine-waste stream of the cleaning plants. To improve the filtration rate and reduce overload episodes, conventional rotary blowers were replaced with high pressure air blasters on most of the filters. Subsequent testing indicated that measurable benefits can be derived from this modification.

Jan 1, 1990

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By Russell C., Fleming

FOK, many years the officials of the Magma Copper Co. mine at Superior, Ariz., have had to contend with adverse conditions underground in the form of high rock temperatures, hot water, and high relative humidity. These conditions in the mine have been such that working the mine would have been impossible were it not for the constantly expanding and improved sys- tem of ventilation to produce bearable conditions in the working places. Results that have already been achieved make an interesting study of what can be done along those lines. From the time the mine was first opened in 1910 it has been hot. An idea of the conditions that have persistently been encountered can be obtained from parts of the mine that are not being worked at present or that do not yet have sufficient ventilation. Virgin rock temperatures as determined in drill holes at the faces range from 104° to 116°*. An observation made at the face of No. 5 West footwall drift on the 2800-ft. level.

Jan 1, 1930

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By G. A. Walsh, M. Timm, S. M. Geerts

This paper will discuss the effectiveness and the general use of improvised shaped charges. Testing was conducted by the New Mexico Tech Student Chapter of ISEE and held at EMRTC. The first series of tests conducted was to illustrate the performance of different features of the shaped charge. A PVC pipe filled with C4 with no cavity, PVC with an unlined conical cavity, PVC with a copper lined conical cavity and no standoff, and lastly a PVC pipe with a copper lined cavity and a 1.5 cone diameter standoff.

Jan 1, 2010

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By J. H. Rowland, A. C. Smith, K. A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame-resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68° C and 141° C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large-scale experimental configuration, the installation specifications of the fire suppression system and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature and limited water application on the suppression system performance.

Jan 1, 2010

By Alfonso Brazzini Díaz Ufano

El presente texto señala la estrategia de la disminución del impuesto de ventas, así como el aumento a las tasas de renta dentro del desarrollo minero. Para ello, es necesario incentivar la ampliación de la capacidad instalada actual de la mediana minería a través de una ley, donde el Estado no deje de percibir súbitamente el impuesto a las ventas y pueda recuperar una parte de él por un impuesto a las utilidades cuando las empresas presentan recién sus declaraciones juradas, de forma que solicite a las empresas mineras a acogerse al sistema del pago a cuenta del impuesto a la renta en base a balances mensuales.

Mar 1, 1979

By Dinner Paredes

El presente trabajo técnico, denominado “Impulsando la competitividad minera en el Perú: La economía circular y los incentivos tributarios como elementos claves para el desarrollo de una minería sostenible”, tiene como propósito primordial analizar y resaltar la importancia que tienen los principios de la economía circular y los incentivos tributarios para promover un sector minero competitivo y sostenible en el Perú.

Sep 29, 2023