Search Documents

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

By K. Rajamani

A mathematical model based on the pertinent fluid dynamic equations to predict the performance of the hydro cyclone has been developed which will eventually replace the empirical model. Experimental measurements of fluid velocity profiles made in a 75 mm hydrocyclone by laser Doppler velocimetry (LDV) agree well their predictions by solving the Navier-Stokes equations numerically. Particle slip velocity and particle trajectory were computed which in turn, yields separation curve of the hydrocyclone.

Jan 1, 1988

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By L. H. E. Weyher

In a previous paper presented at the 1966 Annual Meeting of AIME we reported our work, conducted at the Pennsylvania State University, on the hydrocyclone washing of fine coal.' The initial evaluation based on that work demonstrated the feasibility of hydrocyclones as fine-coal cleaning devices, and in that previous paper we presented selected test data that showed in principle how product yield and assay respond to variations of the major cyclone operating variables. The present paper reports in greater detail on the findings and presents a comprehensive evaluation of our data as follows: ? Hydrocyclone throughput rates were related to feed pressure and other variables by regression equations. These equations are compared with other capacity- versus-pressure drop expressions taken from the literature on classification cyclones.

Jan 1, 1968

By D. T. Jr. Tarr

History of Development The hydrocyclone, probably because of its basic simplicity, has been used for various classification applications since before 1890. A patent was granted in the United States in 1891 to Bretney on a device for separating sand from water, collecting the sand in a closed chamber for intermittent discharge, practically identical to some present-day water desanding cyclones. Between 1900 and 1937 there were 30 or more additional patents issued on liquid cyclone configurations or their use. About 1937 liquid cyclones began to be used commercially in the treatment of cellulose fiber in the pulp and paper industry separating contaminating particles from the fiber in water suspension used for making high grade paper products. Nichols Engineering & Research Corp. of New York was marketing a liquid cyclone for cleaning sand and din particles from fiber suspensions in the pulp and paper industry by 1937. The designs during this period were such that the cyclones discharged a small amount of relatively high density material into a chamber connected to the cyclone apex which in turn discharged the collected dirt material intermittently. By the early 1940s hydrocyclones as we know them today began to appear both in the pulp and paper industry and in coal prorzssing.18 Considerable experimental work was done on small, mostly 3-in.- diam, cyclones operating at relatively high pressure drops, in the range of 50 psi, to remove very small contaminating particles from cellulose fiber in the production of high-grade writing papers in the paper industry.18

Jan 1, 1985

By W. Rubarth

The kaolin losses in hydrocyclone classification are determined by the fines, which are discharged together with the water to the underflow. This paper presents an improved technique of water injection to the conical part of the cyclone applied especially for small cyclones in kaolin preparation. In small hydrocyclones water, injection is a sensitive process. Therefore, the process was stabilized by controlled water injection dependent on the measurement of the underflow shape. Three applications of this innovation are presented. In the first case, the water injection is applied for the separation stage in dilute suspension where the final product is produced in the overflow of a 50mm hydrocyclone. The underflow contains sand and residual kaolin. For a higher kaolin recovery, the underflow is usually treated downstream in washing cyclones. The wash water injection results in a 45 ? 50% - reduction of the kaolin fraction <25µm in the underflow. Thus, water injection to the classifying cyclone leads to a separation comparable with a downstream washing stage. An additional hydrocyclone stage can be deleted. The second application refers to a classification in dense suspension. Here, the underflow of the last hydrocyclone stage was directed to a washing in a 50mm hydrocyclone. The additional injection of 3L/min water in to the conical part of the cyclone reduced the kaolin losses by half.The third application was executed in the washing stage equipped with 75mm hydrocyclones where the underflow is directed to flotation. Using the water injection the kaolin recovery in this stage was increased by approximately 20%. Keywords: hydrocyclone, classification, kaolin beneficiation, water injection, underflow washing

Sep 1, 2012

By Y. H. Kim

A simulation procedure has been developed that realistically portrays aggregate growth and disintegration for particular types of floc structures in water and wastewater treatment processes. The procedure requires local dissipation rates and specification of an interaction distance between colliding particles. A principal difficulty encountered in polymer flocculation, however, arises from changes in conformation of adsorbed macromolecules. Therefore, in systems where polymer flocculation occurs by bridging, dynamic changes in the particle size distribution depend upon the interaction of nonlinear. stochastic hydrodynamics with particles whose growth results from a number of concurrent and sequential random processes.

Jan 1, 1988

By W. Yang, R. Rajasingam, K. Mohanarangam

"Copper Electrowinning (EW) is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. The process setups up a complex flow pattern within the cell as it is subjected to varying density gradients due to the deposition process along with oxygen bubble driven flow. It is a necessity to understand and quantify the flow behaviour within these cells in order to maintain the production of highest grade copper. In fact, the oxygen bubbles originating from the process is responsible for the generation of acid mist which is a designated as a carcinogen a major health hazard around EW tank houses. Hydrodynamic assessment of the process has so far been restricted to simple mass balances and some limited numerical modelling. All the models are based on assumed boundary conditions which has not so far been verified by any real-time physical measurement. This apparent gap has led to models which could not be directly used to track process changes or troubleshoot problems in EW tank houses. In order to address this gap, CSIRO has established a full size (width and height) transparent cell capable of simulating plant operating conditions (across the range currently used). With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables (current density, flow rate, temperature, etc.) independently and their effect of bubble size, bubble velocity, gas hold-up as well as acid mist generation and its size. In order to address safety concerns in tank houses around acid mist early results outlining the factors contributing to its generation as well as the effect of various barriers to mitigate acid mist is outlined below.INTRODUCTIONA significant part of today’s copper production is through hydrometallurgical route which predominantly involves leaching, Solvent eXtraction (SX) followed by ElectroWinning (EW). Producing copper using this approach have shown to be environmentally friendly (Dresher, 2001) compared to the traditional smelting process. EW is the final step in the production of LME grade copper using the hydrometallurgy route. The electro-chemical process involves the use of a lead anode (Pb-Sn-Ca) and a stainless steel cathode to produce copper sheets using the copper rich electrolyte from the SX process and with the applications of direct current to the electrodes. This electro-chemical reaction results in the deposition of copper ions on the cathode with oxygen released from the anode as a by-product. Hydrodynamically, the oxygen bubbles create a bubble driven flow within the EW tanks with the surrounding electrolyte. A direct result of this could be seen from the quality of the copper deposited on the cathode. Most of the copper plates produced from the traditional tank houses have a rough texture at its bottom one-third while the top two-thirds have a smooth finish with a finer grain structure."

Jan 1, 2016

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

By K. Cole, D. Mesa, P. Brito-Parada, M. R. van Heerden

Turbulence in mechanical flotation cells, achieved via an impeller, plays a key role in keeping particles in suspension, dispersing air bubbles, and promoting particle-bubble collision. However, studying the hydrodynamics of a flotation cell is not a simple task, due to the complex nature of flotation systems which are opaque, turbulent, multiphase and polydisperse in terms of particle and bubble sizes. In this paper we study the impact of impeller design modifications on the hydrodynamics of a continuously overflowing bench-scale flotation tank. To this end, two different impeller designs, with and without a stator, were assessed using Positron Emission Particle Tracking (PEPT). This allowed the authors to determine, for the first time, the effect of an impeller design on the behaviour of both hydrophobic and hydrophilic particle tracers. It was experimentally observed that the use of a stator modifies the hydrodynamics within the flotation cell, distorting the lower mixing loop that is characteristic of axial impellers. The role of the stator in dissipating turbulence results in reduced particle velocities outside of the impeller-stator region. These results have important implications for flotation cell design and are discussed in the context of the impact that different designs have on particle movement, flotation hydrodynamics and, ultimately, flotation performance. The data set generated is also extremely valuable for modelling and validation purposes. Keywords: Flotation, flotation tank, impeller design, rotor, stator, PEPT, hydrodynamics

Jan 1, 2020

By C. E. Jordan, B. J. Scheiner

The Bureau of Mines conducted research on the flotation hydrodynamics of fine particle flotation to improve the flotation efficiency in our domestic minerals industry. The turbulent fluid velocity profile was measured in various flotation cells at different levels of dissipation energy. The importance of dissipation energy and bubble size within the flotation cells for the flotation response of a chalcopyrite ore was evaluated. Both increased turbulent fluid flow and fine size bubbles improved the flotation rate of fine size chalcopyrite particles.

Jan 1, 1989

By Kevin Galvin, James Dickinson

"The Reflux Flotation Cell (RFC) consists of an inverted fluidized bubbly bed, located above a system of parallel inclined channels. This novel arrangement enhances the hydrodynamics of flotation in a number of ways. Firstly, the free-surface of the flotation cell is enclosed via a fluidized bed distributor, ensuring uniform application of wash water to promote desliming. Secondly, foams can be variable in their stability and lack permeability. Hence this system is preferably operated in the absence of foam, instead opting for a bubbly zone of high bubble volume fraction through the use of a very high gas flux and/or wash water flux. Discharge of the product proceeds upwards through a central port of narrow cross-sectional area. Thirdly, the system of inclined channels increases the segregation between the bubbles and the water, ensuring the bubbly zone remains contained within the upper vertical zone, and the liquid flux reporting to the overflow is low. The expanded operating regime of the RFC was investigated by covering a very broad range of gas fluxes, up to 5.5 cm/s, and wash water fluxes, over 2 cm/s. Both laboratory and pilot plant performances were quantified by the recovery of hydrophobic particles and rejection of the hydrophilic particles, using model and industrial coal feeds. The new system hydrodynamics was found to offer significant advantages in flotation kinetics, desliming, and particle recovery across a broad particle size range. Bubble interfacial flux reached as high as 600 m2/m-2s-1. The upper system consists entirely of a high volume fraction of bubbles, which provides a "safety-net" to protect against the detachment of coarse particles, and a highly permeable zone for counter-current washing of the flotation product. Under relatively extreme conditions selective stripping of the product is observed, resulting in grade recovery values beyond those achievable using the tree flotation method."

Jan 1, 2014

By V. R. Degner

The minerals industry trend toward very flotation machines, exceeding 10 m3, began in the late 1960&apos;s and responds to the continuing desire to achieve better plant economics through improved plant floor-space utilization, power requirements, and operational /maintenance manpower heeds. In general, as process design tonnage increases, the benefits of the larger flotation machine becomes more evident. The development of the larger flotation machine can be distingushed from earlier, smaller, machines in demanding a rational "scale-up" procedure to guide the basic design, thereby producing a machine prototype capable of satisfactory-operational evaluation at minimum cost. Proven flotation machine "hydrodynamic" scale-up consideration, successfully applied in the development of both the WEMCO No. 164 (28.3 m3) and No. 190 (42.5 m3) machine will be reviewed, and the resulting economic benefits of large flotation machines in high tonnage applications will be summarized.

Jan 1, 1985

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

Hydrodynamic investigations in exploratory boreholes and grouting holes are conducted for the purpose of obtain¬ing information about the hydraulic properties of the hydrostratigraphic section to be intersected by the proposed underground workings. The information obtained from the investigations provides the basis for calculating the hydrau¬lic coefficients of fractured permeable rock, the dimensions of the anticipated grout isolation curtain(s) around the un¬derground workings, the number and location of grouting holes, the injection pressure modes, and also the volume(s) of grout that will be required (Anon., 1976, 1978). The following data on each aquifer are obtained from the investigations conducted in monitoring and grouting bore¬holes and the analysis of the results: 1) the top of each hydrostratigraphic unit, 2) the thickness of each unit, 3) the ground water fluid potential distribution in each unit, 4) the coefficient of permeability, 5) the piezoconductivity, 6) the fracture porosity, 7) the geometry of the fractures in the rock, 8) the elasticity-compressibility coefficient of the fractured rock, 9) the chemical composition of the ground water, 10) the direction of flow of the ground water, and 11) the expected inflow rate of water into the shaft, drift or tunnel. STG uses its DAU-3M type flowmeter to conduct in¬vestigations of directions of flow in vertical, inclined and horizontal drillholes. The DAU-6 instrument is used to de¬termine the direction of flow of ground water in each frac¬ture or fractured aquifer. Various singular and double DAU type packers are used for pumping and for injection studies (tests) and for flowmeter investigations. Normally the instruments enumerated above permit in¬vestigations to be conducted in each separate aquifer with¬out reinforcing the holes with casings. On the basis of these investigative data, both the hydraulic properties of unfractured rock and the hydraulic properties of the fractured rock are estimated. Dual porosity rocks require special attention because they tend to segregate the grout. 3.1 FLOWMETER INVESTIGATIONS IN BOREHOLES The STG flowmetric methodology is based on the mea¬surement of the ground water flow rate through the borehole by hydrostratigraphic interval after the disturbance of the hydrostatic equilibrium in the "hole-aquifer system" (after pumping or injecting). The relationship of the head changes to the discharge into or from a particular hydrostratigraphic unit obtained during the tests serve as the basis for calcu¬lating the hydraulic properties. Flowmetric investigations facilitate the determination of the number of aquifers, their depths, their thickness, the hydraulic properties of the fractured rock and the magnitude and direction of the flow of ground water. 3.1.1 FLOWMETER HARDWARE STG conducts flowmetric investigations in boreholes using its DAU-3M-108, DAU-3M-73, DAU-3M-57 and DAU-3M-44 instruments.&apos; They have respective external diameters of 108, 73, 57 and 44 mm. The type of flowmeter selected for use depends on the borehole geometry and the technological scheme for carrying out the investigations. Boreholes with a drilling diameter of 76-93 mm are inves¬tigated with the DAU-3M-73 flowmeter; boreholes drilled by bits with a diameter of 112 mm and more are investi¬gated using the DAU-3M-108 flowmeter. The DAU-3M¬108 and DAU-3M-57 instruments are used for flowmetric investigations with a packer. 3.1.1.1 The Downhole Sensor The sensor design of the DAU-3M-73 hole flowmeter is shown in Fig. 2. The design of the DAU-3M-108 instru¬ment is similar to the design of the DAU-3M-73 instrument. The frame of the flowmeter sensor shown in Fig. 2 consists of a casing, an upper and lower centering mount and two rings to which the guiding rods are attached. The upper rods are built into the connector bushing; the lower rods are built into the coupling sleeve. The borehole cable is attached using a half-coupling, a packing ring and a constriction nut. Thus, the frame of the flowmeter sensor is made so that the free passage of water to the impeller is facilitated along with the necessary rigidity. The primary moving component of the flowmeter is the double-bladed impeller, which rotates on cobalt-tungsten pivots and agate thrust bearings. Special extended air cham¬bers protect the supports of the impeller from the action of the borehole fluid which may contain fibrous and abrasive particles. The air located in the chambers shields the sup¬ports from direct contact with the borehole fluid when the sensor operates in a borehole. The hollow casing of the impeller serves the function of a lower cap. The upper cap is attached to the casing using a threaded connector; it is affixed also with a lock-nut. An adjusting screw with a

Jan 1, 1993

CSIRO Minerals, in association with the AJ Parker CRC for Hydrometallurgy, has an active program of hydrometallurgical research in which physical and computational modelling are used to better understand and improve a range of different unit operations. The modelling is based on flow simulation (Computational Fluid Dynamics or CFD), but incorporates other physical and chemical phenomena of importance, such as droplet break-up and coalescence, species transport and reaction. This paper reviews some of the major projects that have been undertaken at CSIRO Minerals and will illustrate the critical importance of hydrodynamics to the performance of unit operations and the improvements that can be made to performance using such modelling techniques. Unit operations that are discussed include solvent-extraction, gravity thickeners, flotation cells, bio-heap leaching and stirred tanks.

Jan 1, 2005

By T. Joseph, E. Zheng, M. Curley

"Hydraulic transportation efficiency and production optimization are considerations in the surface extraction of Athabasca oil sand deposits. To reduce the dependence on haul trucks, it is possible to extend the hydraulic transport system to production faces using a mobile at-face slurry system (AFSS). The flexible arrangement of connected pipelines transports slurried minerals from the mining face to the processing plant. An experimentally verified mathematical model indicates the friction loss of oil sand slurry associated with the AFSS. Laboratory-scale testing enables extended analyses for examining pipeline slurry transport in an oil sands environment.RÉSUMÉ L’optimisation de l’efficacité du transport hydraulique et de la production sont des considérations importantes dans le domaine de l’exploitation à ciel ouvert des gisements de sables bitumineux de l’Athabasca. Afin de réduire la dépendance envers les camions de transport, on envisage d’étendre le système de transport hydraulique aux fronts de taille à l’aide d’un système mobile de transport des matériaux sous forme de boue à partir du front de taille (AFSS, de l’anglais at-face slurry system). L’organisation flexible des conduites reliées permet le transport de minéraux à l’état de boue du front d’exploitation jusqu’à l’usine de traitement. Un modèle mathématique vérifié de manière expérimentale indique la perte de charge par frottement des schlamms provenant du traitement des sables bitumineux associée à l’utilisation de l’AFSS. Des essais en laboratoire permettent de mener des analyses approfondies portant sur le transport de boues dans des conduites dans un environnement de sables bitumineux. INTRODUCTIONObjectives and scope of studyThe at-face slurry system (AFSS) concept has become a competitive means for materials handling to optimize haulage system efficiency and cost. The mobile and flexible arrangement of the AFSS introduces a unique set of hydraulic transport problems. This paper will focus on developing the mathematical models governing the friction and head losses within the AFSS concept.Background of the problemLarge-capacity shovels and dump trucks are increasingly used for excavation, loading, and hauling in the operation of surface mining. Production cost and efficiency optimization are demanded during the Athabasca oil sands (Alberta, Canada) mining process to secure North America’s energy supply. Increasing haulage distances, rugged terrain, and a constrained mine environment are conditions that will reduce the effectiveness of the shovel-truck haulage system (Frimpong, Szymanski, & Changirwa, 2003). In such conditions, the tire heat index and weight, distance, and time limits for truck haulage can be exceeded, simultaneously creating extreme tire wear and high maintenance costs. In addition to low production cost and equipment effectiveness, a mining environment also requires efficient waste-material recycling and distribution. Waste materials need to be recycled from the processing plant to a new destination such as a tailings dam, or replaced in mined-out areas such as backfill. The Athabasca oil sands configuration and location characteristics result in a mining environment that would benefit from flexible pipelines for constant production and an efficient waste-material recycling process."

Jan 1, 2017

By Narasimha Mangadoddy, Balraju Vadlakonda

"Bubble size distribution, bubble rise velocity and gas and solids hold-up are the key major hydrodynamic parameters that are extensively used for column flotation design and performance evaluation. The distribution characteristics of mean gas hold-up is studied using electrical resistance tomography (ERT) coupled with pressure transducers (PT) in column flotation. The ERT technique facilitates non-invasive and nonintrusive visualization of different flow regimes even in the presence of particles in a column flotation. The effect of superficial gas velocity, feed flow rate and slurry height in the column on mean gas hold-up and its radial distribution has been analysed for both two-phase and three phase flows. Experimental results show ERT coupled with PT is suitable as an online monitoring tool to provide useful information on the three-phase flow hydrodynamic parameters of the column flotation. The tomography images, which were generated using a modified sensitivity back projection algorithm, are employed to explore the influence of parameters in two phase flow in column flotation. Mean gas and solids hold-up values extracted from ERT have been critically analysed for the column operating in various flow regimes. Gas hold-ups and solid hold-ups results using ERT are in very good agreement with conventional estimation and correlations obtained using pressure transmitter methods. Meanwhile, the results show that the gas hold-ups in the centre region increase constantly with an increase in the superficial gas velocity, whereas solid hold-ups distribution is very heterogeneous for high gas velocity. Furthermore, the results also indicate that ERT is a very powerful tool for diagnosing the 'inside' flow behaviour of gas –liquid–solid three phase flow in columns operating for a wide range of flow regimes.INTRODUCTIONColumn flotation is perhaps the most significant technological innovation in flotation machinery and its successful introduction in mineral processing plants. There has been a lot of attention in understanding the various mechanisms that take place during operation. Due to many reasons column flotation has been found to yield better performance than conventional flotation cells, particularly with fine particles (Honaker & Mohanty, 1996). Due to complex flow behavior in nature, the performance of column flotation influenced by on flow characteristics of the process, (Jena, Biswal, Das, & Reddy, 2008). Previously basic research is carried out to evaluate the effect of the hydrodynamic parameters on performance of column flotation (Finch, J.A.;Dobby, 1991). Many techniques have been developed that could be used to experimentally analyse the hydrodynamics of column flotation. Tomography techniques are well sound to investigate the hydrodynamics for process equipment. Among that, Electrical resistance tomography (ERT) has been used in various industrial investigations for visualization of the concentration profiles and characteristics of the fluid dynamics in gas–liquid two-phase systems (Wang, Dickin, & Mann, 1999; Williams, R.A; Wang, 2000). ERT is an imaging technique to analyse the internal flow behavior non-intrusively. ERT provide very useful tools for measuring and monitoring of column flotation process on line. Due to its high speed capability, low cost measurement, robust sensors, ERT is considered to be the most powerful tool among other tomography techniques such as positron emission tomography (PET), magnetic resonance imaging (MRI), optical and infrared tomography. Application of ERT has extended in process systems due to its improved speed of data acquisition, sensitivity, flexibility and noise immunity. In multiphase flow of bubble columns, gas hold-up and solid hold-up are explored by using the coupling of ERT and difference pressure method (Jin, Han, Yang, & He, 2010)."

Jan 1, 2016

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016

By R. Bugueño, W. Calderón, G. Montes-Atenas

From the point of view of industrial performance of metal extraction, the efficiency of a column leaching operation depends strongly on the leaching agent and the ore properties such as mineral composition, mineral liberation and particle size distribution. One aspect that has become particularly important is how the leaching solution flows through the porous structure which contains the valuable minerals. It is known that the output flow rate of leaching solution depends mainly on factors of the input flow, environmental condition and porous bed properties. The latter factor is often evaluated and reported under saturated conditions but in practical leaching systems unsaturated conditions are dominant. This investigation has the purpose of determining the residence time of the leaching solution in columns with different diameters under unsaturated conditions by using experimental data and numerical simulations. Laboratory leach test were performed using isothermal jacketed columns with top cap to reduce the evaporation. The simulations were performed using the software SVFlux® which incorporates material properties such as Soil Water Characteristic Curve (SWCC) and Unsaturated Hydraulic Conductivity. Preliminary results indicate a non-linear asymptotic behavior of the saturation rate with respect to the operation time. Results from numerical simulations show the same non-linear behavior and a considerable delay between input and output flows. Further analysis concerning with the effect of transpiration and evaporation mechanisms is discussed.

Jan 1, 2014