Search Documents

By Jin-Hwa Song

Rolling temperatures and cross rolling ratios were varied to investigate the effect of crystallographic texture of alpha-phase on the anisotropy of mechanical properties in modified Ti-6A1-4V alloy. Hot rolling method was unidirectional and cross rolling, during which the rolling temperature was in the range of 830°C and 920°C. Cross rolling ratios were varied from 0.3 to 1.0 at 875°C. For unidirectional rolling, as the rolling temperature increased texture changed from the mixed basal and transverse texture to the simple transverse texture. Contrary to other work, it was observed that the maximum intensity of transverse components increased with the increase in rolling temperature. For cross rolling, on the other hand, the transverse texture component was almost suppressed at 830°C, giving rise to a symmetrical basal texture. With increasing cross rolling temperature, the transverse texture components developed again. A simple transverse texture, which showed two maxima appearing circularly 90° apart, was observed at 920°C. It was found that unidirectional rolling could not eliminate the transverse texture, which resulted in the anisotropy of mechanical properties. The anisotropy of mechanical properties obtained from tensile and V-notch Charpy test was closely related to the crystallographic texture and its intensity at each rolling condition. To obtain the isotropy of mechanical properties by cross rolling, it is suggested that cross-rolling ratios should be controlled above 0.5. The variation of rolling temperatures and directions has great influence on the anisotropy of impact value rather than tensile strength.

Jan 1, 2004

By Marcelo Rebellato, Beatriz Pereda, Beatriz Lopez, Pello Uranga

The classical application of Nb microalloying in the development of thermomechanical processes for flat products has been related to its suitability to enhance strain-induced precipitation and get a pancaked austenite prior to transformation. As new steel grades or new lay-outs are being developed, more complex metallurgical conditions need to be evaluated. In this context, Nb microalloying, alone or combined with other microadditions, needs to intervene in a more controlled way in additional steps of the thermomechanical process, besides its conventional strain-induced precipitation role. For example, the hardenability enhancement associated with Nb to properly achieve lower temperature transformation products, demands a proper balance of the Nb amount precipitated during rolling and the one remaining in solid solution. Similar effects are also sought when the final available Nb is used to increase strength through precipitation hardening. This manuscript evaluates how changes in the rolling strategies affect the interaction between Nb(C,N) precipitation and austenite recrystallization at different steps of the rolling process. As the possible interactions between parameters intervening simultaneously are quite complex, the application of microstructural models helps to properly define the best austenite conditioning combined with the convenient amount of Nb in solution, as a function of the final property requirements. Along the manuscript, several strategies will be discussed for the case of hot rolling of flat products comparing both normal and coarse initial austenite grain sizes.

Oct 1, 2019

By Michael W. Roper

McDermitt Mine is located in northern Humboldt County, Nevada, approximately 5 miles south of the Orgeon-Nevada line (Figure I), within the Opalite Mining District. The operation is a joint venture between Placer Amex Inc., San Francisco, and Mineral Exploration Company Ltd., a limited partnership. The McDermitt orebody possesses a discontinuous, gently dipping blanket-like form within 150 feet of the surface over an area 2200 by 2500 feet. The ore zone averages 20 feet in thickness. The ore minerals consist of cinnabar (HgS) and corderoite (Hg3S2C12) deposited parallel to bedding within argillized, Miocene age, tuffaceous lacustrine sediments. Exploration indicates reserves of approximately 3,000,000 tons ore at a grade of 10 pounds mercury per ton (0.5%) An open pit mining operation utilizing scrapers and bulldozers supplies a concentrator with 700 tons of ore per day. The milling operation consists of autogenous grinding, flotation concentration, concentrate dewatering, and tailing disposal, with a design capacity of 100 tons per hour. The furnace section consists of a concentrate filter, vertical six hearth furnace, mercury condensing system, and exhaust gas scrubbing systems. It has a design capacity of 1000 pounds of dry concentrate per hour. The McDermitt orebody is situated about 2000 feet north of the Cordero Mine which, with adjacent properties, produced over 115,000 flasks (76 pounds per flask) mercury from 1941 to 1972' Two other major mercury producers in the district have been the Bretz and Opalite Mines, located in southern Malheur County, Oregon, within 5 miles of the Oregon-Nevada line. Bretz and Opalite have produced about 14,800 and 12,370 flasks mercury respectively, from 1926 to 1965.1/

Jan 1, 1976

By Michael W. Roper

McDermitt mine is located southwest of McDermitt, Nev., ½ mile north of the old Cordero mine. Geologic structure of the district is that of a Miocene age collapse-type caldera in a region of Basin and Range normal faulting. The McDermitt ore body possess a tabular, gently dipping configuration within 150 ft of the surface over an area 2200 x 2500 ft. Indicated ore reserves are 3 million tons at 10 lb Hg per ton. The ore zone averages 20 ft in thickness and consists of cinnabar (HgS) and corderoite (Hg3S2Cl2) deposited parallel to bedding in argillized Miocene age tuffaceous lacustrine sediments. The ore body is localized above a silicious sinter-silicified lake-bed breccia. This "opalite" breccia unit possesses a gently dipping, apronlike configuration, striking northeast, parallel the trend of the Cordero deposit, and thinning to the north and northwest.

Jan 1, 1977

The completion of the Hot Strip Mill at the Port Kembla works of Australian Iron & Steel Ltd., makes possible the production of steel plates and wide strip of a quality and in quantities not possible previously in Australia, and will also enable the production of tinplate to be undertaken in this country.The site chosen for the mill was a mud fiat underlain by a hard stone bottom at 5, to 801 feet below the surface; and a total area of one hundred acres was reclaimed to a level of 20 feet above the original surface.Three adjoining buildings were constructed to house the slab receiving yard, mill equipment and electric drive, together with the plate finishing line.After slabs have been heated to 2250°F at a rate of 90 tons per hour, they are transferred to the vertical scale breaker which is the first stand in the hot roughing mill. Here the primary furnace scale is first cracked and then blasted off by high velocity water descaling sprays.The next stand is the horizontal scale l;Jreaker, where any remaining primary scale is broken and then blasted off. After descaling, the slabs pass to the broadside mill, where short slabs are turned and rolled on broad side for wide plate.The next step is a slab squeezer which squares up the edges after broadsiding ready for the reversing mill. This is the finishing stand for plate and the last roughing stand for strip, which then passes to the finishing mill.The hot strip finishing mill consists of six stands with a maximum finishing speed of 2,230 feet per minute. Strip is cooled for coiling by water sprays on a hot run table and then coiled on a mandrel type downcoiler, from whence coils of hot strip are weighed and transferred by conveyor to the coil storage building.Plates are transferred from the reversing mill to the plate finishing line where operations consist of levelling, inspection, branding, cutting to width and length:INTRODUCTIONDue'to the increasing production of cars, refrigerators, washing machines and similar consumer goods in Australia, together with the increased requirements of galvanised iron...

Jan 1, 1956

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

The abstract discusses the issue of mine equipment fires caused by hot surface ignition of flammable liquids. The research investigates the ignition probability of liquid fuels (diesel, engine oil, hydraulic fluid) on different metal surfaces (stainless steel, cast iron, carbon steel) under various ventilation speeds. The results show that the type of metal and ventilation speed influence the ignition temperature, with diesel being the most easily ignited fuel and carbon steel requiring a higher ignition temperature. The study provides data for understanding equipment mine fires and developing mitigation strategies.

May 4, 2022

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

By J Isles, S King, A Valenza, R Lawolo, J Evert

PT Nusa Halmahera Minerals (PT NHM) is an Indonesian joint venture company owned by a subsidiary of Newcrest Mining Limited (75 per cent) and PT Aneka Tambang (Persero) (25 per cent). PT NHM operates two underground gold mines, Kencana and Toguraci at the Gosowong mine site in North Halmahera District, North Maluku Province, Indonesia.The Toguraci underground mine development commenced in 2011 with ore production commencing in 2012. Water temperatures ranging from 50°C to 80°C were encountered in the Toguraci open pit associated with the structures containing the gold bearing veins and are believed to be fed from a relic volcanic system one to two kilometres below the mine. Underground development and production has continued to intersect these structures with the result that an integrated programme of geological, hydrogeological modelling and operational project work has been required to dewater the mine ahead of the descending stoping fronts.This paper will detail these programmes.CITATION:Lawolo, R, Isles, J, Evert, J, Valenza, A and King, S, 2017. Hot water management at PT Nusa Halmahera Minerals’ Toguraci Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By P. Leo

The Al-Zn-Mg alloys (e.g. 7004, 7020) are employed for land transport and architectural applications whereas the Al-Zn-Mg-Cu alloys (e.g. 7075, 7050) provide the high strength aircraft alloys. The Cu gives rise to suitably sized and distributed precipitation but causes high quench sensitivity. Their hot work processing also has marked differences; the Cu-free alloys have good extrudability whereas the Cu-bearing alloys have low extrudability and are difficult in rolling as well. The behaviors of the two classes are described in terms of flow stresses and ductility over 300 - 500°C, along with constitutive contrasts. The ductility of the alloys with Cu is much reduced above 400°C by precipitation of a phase at the grain boundaries that can be avoided by suitable heating schedules. The high strength alloys are subject to de-lamination corrosion of sheared edges due to severely pancaked grains; this can be alleviated by holding between passes, in mid-rolling schedule. In torsion tests at 10-1 to 10 s-1/ 250 - 500°C, the stresses (ductilities) at 300°C/ 1s-1 and activation energy Q for 7004 were 118 MPa (2) and 262 kJ/mol. The 7075 was tested after several pretreatments: completely over-aged (softened): 107 MPa (5), Q=150 kJ/mol; whereas, solution and quick cooling to testing caused extraordinarily high peaks related to dynamic precipitation resulting in 160 MPa (1.2), Q=300 kJ/mol.

Jan 1, 2011

By G. Kugler, M. Tercelj

"The 1.2690 high alloyed tool steel is usually applied for cold working and is alloyed with carbide-forming elements Cr, V, W and Mo. It exhibits very poor hot deformability. Since there is no enough available data in literature for elucidation of this problem, hot workability and development of microstructure during hot deformation was studied. Hot compression tests were carried out in temperature range 850-1150 °C and strain rates range 0.001-6 s-1. SEM and OM were used for observation of microstructure. Results revealed very complex precipitation of carbides that depends on deformation temperature as well as on strain rate. It was found that especially at lower temperatures of hot working range the precipitation of carbides strongly depends on strain rate. Three different hot deformation behaviors’ were observed depending on temperature and strain rate range.IntroductionThe hot workability of highly alloyed high speed steels is usually described as relatively poor in comparison to other steels due to their tendency of cracking during hot working especially when inappropriate hot working conditions are applied. Alloying elements such as Cr, W, Mo and V in ledeburitic tool steels form carbides that improve hardenability, strength, hardness, wear resistance, etc., but they decrease hot workability and narrow hot working temperature range in comparison to conventional steels. The size, distribution, type and fraction of carbides, as well as the thermomechanical history of material and hot working parameters have major influence on the hot workability. The microstructure of ledeburitic tool steels during hot deformation can be characterized as a two-phase system consisting of an austenite matrix and a combination of ledeburitic carbides [1-4]. In the soft-annealed condition the total volume fraction of carbides is in the range 19-30% and in the quenched condition in the range 9-25%, depending on the chemical composition. During heating before deformation a large quantity of carbides dissolve, but non-dissolved carbides can have an extremely diverse influence on the hot workability due to variations in their composition, size, distribution, hardness and shape, and their different behavior during the deformation phase [5-7]."

Jan 1, 2011

By Lztok Peruš, Goran Kugler, Matevz Fazarinc, Milan Tercel

"Hot deformability of M42 tool steel additionally alloyed with cobalt and molybdenum was investigated. Hot-compression tests were carried out in the temperature range 850 °C -1200 °C, at strain rates range 0.001--6s-l up to strain of0.9. Field-emission scanning electron microscope and optical microscopy were used for characterization of microstructure of deformed samples, which revealed a very complex precipitation of carbides that strongly depends on the soaking temperature, the soaking time, the stress state, the deformation temperature as well as on the strain rate. Gathered data was used to calculate the processing parameters such as process maps, apparent activation energies and strain hardening exponents. For better understanding of thermodynamical properties of the studied steel a simultaneous thermal analysis was conducted. Furthermore the analysis of phase equilibrium was calculated using Thermo-Cale software. On the basis of these studies the optimal soaking temperature and process windows were determined.IntroductionHot workability ofledeburitic tool steels is important economic factor. This means that for each tool steel individuallysafe range of hot working parameters should be revealed. Publications in the literature with regard to the hot workability of tool steels are rare and therefore more information from this research area is desired.The relatively low hot workability of ledeburitic tool steels, i.e. steels in which the solidification is completed by a eutectic transformation of the residual interdendritic liquid to austenite and various alloy carbides (ledeburitic carbides), is usually characterized by the production of surface and internal cracks during the hot deformation."

Jan 1, 2013

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

By D. G. Hattingh, A Els-Botes

"Considerable information is available on the factors influencing the iron-zinc reaction rate at 450° C of low carbon steels, in comparison there is a scarcity _of similar fundamental information of spheroidal graphite irons. This can be attributed to the more complex microstructure and ferrous alloy chemical analysis of spheroidal graphite irons. Hot-dip galvanizers have identified the complexity in controlling and predicting the thickness of the galvanized coating formed on commercial cast irons, which has serious financial implications for both the galvanizer and customer.Commercial hot-dip galvanizing has been in use for over 160 years and yet an elementary understanding of the dynamics associated with the hot-dip galvanizing of spheroidal graphite cast iron is still insufficient. To allow the. process to become a modem surface engineering technology, the fundamental aspects of the process must be thoroughly understood.When a clean iron or steel article is dipped into the molten zinc, zinc initially solidifies around the steel or iron. As heat is transferred to the article form the bath, this initial solidified zinc layer remelts and a series of iron-zinc alloy is formed by the reaction of the zinc with the surface of the article; on removal from the bath, some of the molten zinc is taken out on top of the alloy layers. At normal galvanizing temperature (450 °C), the reaction between iron and zinc is usually parabolic with time. The rate of reaction is rapid at first but then slows down and the coating thickness does not increase greatly if the article is immersed in the bath for longer times(1)."

Jan 1, 2000

By John G. McLain

OF all the zinc that the world consumed in 1936-'38 the United States took about 31 per cent, and almost 14 per cent of the world's zinc supply in that period was used for galvanizing purposes in the United States. Further examination of the statistics shows that about 71/2 per cent (147,500 tons in 1939) of the world zinc consumption goes into the galvanizing of sheets in the United States, which is what I am going to talk about in this paper. There is nothing especially new about galvanizing; in every year since 1921 somewhere between 41 and 49 per cent of the country's zinc consumption has been used for this purpose, and yet few people not specialists in its manufacture know much about how it is made. You take an iron or steel sheet and dip it in molten zinc and there you have a galvanized sheet-that about epitomizes popular knowledge of the subject even among engineers.

Jan 1, 1941

By Oscar Harder

IT is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing -his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treating high-speed steels. Regarding this research, Dr. Sauveur, (22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and. related materials in the red-heat range, using various methods. . The results, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as its immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By Robert Berggren

THE hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, t but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for con-ventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs. Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Wash-ington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned.

Jan 1, 1940