Search Documents

By Jesús E. Gómez

A recent bridge underpinning project provided a unique opportunity to obtain information on the load-deflection response of 260 hollow-core bar micropiles. All production micropiles were proof-tested to a maximum load of 125 percent of the design load. In addition, four verification tests were performed on sacrificial micropiles to at least two and a half times the design loads. This paper presents the results of the verification and proof tests performed for this project, and provides recommended values for design of hollow core bar micropiles in soils similar to those encountered. This work shows that hollow core bar micropiles provide a significant unit bond capacity in both granular and fine soils, which may be greater than that typically expected in pressure-grouted (Type B) micropiles. The hollow core bar system allows faster installation rates in the soil types encountered than other traditional micropile techniques, and can be installed with relatively simple quality control procedures.

Jan 1, 2007

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

Synthetic hollow microspheres have demonstrated reliable sensitization and detonation characteristics in industrial explosives for almost two decades. During that time, water gel formulations and use conditions have changed. The introduction of emulsion explosives has also dictated technical improvements in microsphere sensitizers. In contrast to microspheres, gassing or other sensitizing techniques often cannot satisfy the manufacturing and blasting characteristics required of today's explosives. This paper discusses the sensitizing properties of microspheres, formulating guidelines and quality considerations. Packaging, sampling, transfer, metering, mixing and pumping information is also provided.

Jan 1, 1990

By J. J. Forbes

Gentlemen : It is a pleasure to come to Glen- wood Springs to participate in this meeting of the Rocky Mountain Coal Mining Institute an organization created to handle chiefly the economic questions dealing with the coal industry of the Rocky Mountain District. I am not unmindful of the many and varied problems confronting the mining industry of this country which is so general at the present time throughout the United States. By reason of the difficulties experienced in marketing the product of your mines, there is all the more reason for greater economy and efficiency in production. No industry can be efficiently operated without giving due consideration to the safety of the employees. Safety and efficiency are inseparable for the success of any industrial enterprise. While the Bituminous coal companies of the United States are doing splendid work in the promotion of safety, yet our fatality rate is exceedingly higher compared with that of foreign countries, and with greater cooperative organized effort on the part of mine owners, mine officials, mine workers, and state and federal governmental agencies having jurisdiction, much more substantial progress can be made in the future and a greater economic saving .to the industry effected, not taking into consideration the greatest and most important phase of safety, which is the conservation of life and health of all those who are engaged in the occupation of mining. You are concerned with freight rates, marketing of coal and similar operating problems. Yet have you earnestly considered the vital question that plays so important a part toward the success of any mill-

Jan 1, 1926

By G. Nuñez, M. A. Pathak, C. F. Stanley

"A 1986 report by the U.S. National Committee on Blomechanlcs (1) describes lung disease as a major national health problem. The report cites three areas that would benefit from a better understanding of the vibratory patterns of the lung. These areas are outlined below.1. In cases of respiratory distress, pressure driven artificial respirators are used. A new technique using high frequency respiration is quite promising, but the pressure distribution in the lung as a function of frequency is not yet known. At these frequencies of 1 to 60 Hz, the lung expands asynchronously (2) and a better understanding of these expansion nonunlformltles could provide valuable Information about the mechanics of high frequency ventilation.2. Listening to the sounds In the lung can yield valuable Information about the state of the lung. To improve the technique, a better understanding of how acoustic waves propagate through the lung is needed.3. The response of the lung as It Is subjected to acoustic excitation, dynamic loading or shock waves is not well understood. A better knowledge of these responees can lead to improved treatment for patients subjected to either explosive pressure waves or car crashes.4. Researchers are measuring the acoustic Impedance of the Iung to detect early states of dysfunction. Sneckenberger and Whitmoyer (3) have reported Impedances obtained at acoustic frequencies up to about 6000 Hz. However, It la not certain which parts of the lung are responding to the acoustic excitation.To Investigate the vibratory characteristics of the lung, excised rat lungs were excited via the trachea with acoustic waves at frequencies up to 6000 Hz. Thie paper describes an Instrumentation system, utlllzlng time-averaged holographic Interferometry, to detect and quantify the response of the lung surface to the acoustic excitation."

Jan 1, 1989

By D. R. Schmitt, B. L. Jensen, T. J. Ahrens, C. L. Smither

The in situ elastic moduli of rock are measured holographically by a borehole instrument in marble and oil shale. A point force induced displacement field is recorded with double expo- sure holography. Data consists of a fringe pat- tern on the viewed hologram. The elastic moduli are determined by modelling of the fringe pattern. Only Young's inodulus is fairly constrained by the present data reduction. For an applied force of 520 [ ] 50 Newtons, a marble was found to have a Young's modulus of 56 [ ] 8 GPa, near an ultrasonically determined value of 48 [ ] 6 GPa. In an oil shale, an applied force of [ ]

Jan 1, 1986

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

By R. H. Colquhoun

"INTRODUCTION The Holt-McDermott Mine is wholly-owned gold mining operation of American Barrick Resources Corp. that begun operations in June 1988.The property is located 0.5 km. south of Highway 101 East in the Harker-Holloway Townships of Northeastern Ontario, 7 miles south of Lake Abitibi and 15 miles west of the Quebec-Ontario border.Employees of the operation travel daily from various communities in the area, predominantly from Kirkland Lake, Ont., which is located 65 km. to the southwest.The significance of the operation is that it is the first full scale operation associated to the Oestor-Porcupine Fault to go into full production in recent history as well as the first Carbon-in-Leach (CIL) operation in the province owing to the natural occurring carbonaceous ores that are associated to the ore body and the geological fault systems.GEOLOGYThe Holt-McDermott deposit is located in the Abitibi Greenstone Belt, a short distance west of the Ontario-Quebec border. Ore grade material follows the footwall contact of a fault zone known locally as the McKenna Fault, which is thought to be a splay off of the Oestor-Porcupine Fault, itself a major feature in the Abitibi belt.The McKenna Fault strikes approximately east-west (as does the Oestor-Porcupine) and dips to the south at sixty-five to seventy degrees. The fault lies within a package of mafic volcanic rocks (basalts). These rocks have been strongly altered and mineralized adjacent to the McKenna Fault, and the resulting lens-like ore bodies constitute the mining targets."

Jan 1, 1989

By AIME AIME

CHARACTERIZING the annual meeting as the biggest and best one yet has happened so repeatedly that some may suspect it has become a conventional phrase, like "good morning," and yet, what else can be said when not only one but all the many who express an, opinion use exactly those words, while the first of the two adjectives refers to a physical fact that is established by count. Perhaps there were hose who thought it not the best, but if so they were too tactful to say it out loud. So without further ado . let us admit that the one hundred and thirty-ninth general meeting of the A. I. M. E. held; as our By-laws provide, in New York during the third week of February, was the biggest and best of them all. Perhaps it is because we appreciate friendliness more as we grow older, but somehow the friendly atmosphere seems to rise slowly in temperature with the passing of the years. The actual atmosphere on the opening morning was quite the contrary, Feb. 17 being the coldest clay, so far, of this winter, and the suburbanites claimed that their thermometers had registered 5" below zero when they got up, though the official records of the weather man did not go that low. From that time the temperature steadily rose until Thursday afternoon, when the official record of 66" constituted a record high for Feb. 20 at New York. The weather man explained it by learned discussion of highs and lows, but we suspect the A.I. M. E. members must have had something to do with it.

Jan 1, 1930

By Thomas Connolly

The Homestake Mine is situated in the northern portion of the Black Hills of South Dakota in a series of steeply dipping and highly folded Precambrian Rocks. The ore bodies are localized along plunging anticlinal and synclinal folds which are locally called "ledges." The gold bearing ore is confined mainly in the Homestake formation which is an iron-magnesium carbonate series of rocks. The individual ore bodies are pipe or lense-shaped zones which plunge 30º to 75º from the horizontal. These ore bodies range from 10 to 100 feet wide and 50 to 400 feet along the strike. Gold values are erratically distributed in a gangue consisting of cummingtonite schist, sideroplesite schist, quartz, pyrrhotite, arsenopyrite, chlorite schist and ankerite. Usually the ore bodies dip at 70° to 80º and often have folded shapes like "fish hooks" or "troughs." Ore grades must be determined by extensive sampling and all mining is based on assay control.

Jan 3, 1974

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By John F. Wiggert

DURING the early years of Homestake operations, shaft signaling from the cage tenders to the hoisting engineers was done by mechanical means. Small steel cables or jointed steel rods were suspended in the shaft compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' stations by means of bell cranks and steel wires. The system was simple and economical and served the purpose well until the mine reached a depth of 1000 ft., then the system became slow and cumbersome and required a considerable amount of muscular effort to operate it with much speed, because of the inertia of the heavy moving parts. The mechanical signaling was superseded by a simple electrical system consisting of a single pair of wires in steel conduit for each shaft compartment. In the shaft at each station a pull switch was connected to the wires. The switches were operated by means of bell cords, which extended from station to station. This electrical system was a great improvement over the mechanical one, but it had one serious drawback, which also applied to the older system; namely, the engineer did not know where a signal originated. Later on this signaling was improved to overcome this drawback, and to give the engineer a positive indication of a signal's origin. In this system a separate return wire from each pull switch is carried to an annunciator at the engineer's station, where it indicates the signal's origin. While the annunciator system used by Homestake is very safe and reliable, it has the inherent drawback of all wire-connected systems in that it is impossible to send a signal from a moving cage. A number of years ago Homestake became interested in the possibility of using some sort of radio transmission for shaft signaling. The company did much experimental work with purely radio signal transmission, but no practical way was discovered to use radio transmission in a mine shaft for signaling to or from a cage. Therefore, all efforts were directed to devising a practical way of using the hoisting rope as part of the circuit. It was realized that the return circuit from the rope would need to be through electrostatic coupling between the cage and the earth or ground sides of the shaft, because the guides would not always be wet enough to make possible good electrical contact between the cage and earth, therefore relatively high-frequency alternating current was chosen as the medium of transmission. Soon a practical system was developed for transmitting an electric current from a moving cage over an electric circuit of which the hoisting rope was a part. A high-frequency electric current is used as a carrier to transmit the signals or mes-

Jan 1, 1941

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine, or for the expansion of an existing mine, can range between 9 months to 24 months, or more. The time frame will vary depending on whether an Environmental Assessment (EA) or an Environmental Impact Statement (EIS) will be completed. Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. The two year natural resource baseline study completed by Homestake Mining Company for the Ruby Hill Mine, located in Eureka County, Nevada will be used as the case study to describe how properly designed and executed natural resource baseline studies streamlined the NEPA process.

Jan 1, 2001

By Steven Mitchell

BACKGROUND Homestake Mining Company began milling operations at the Bulldog Mountain Mine near Creede, Colorado in 1969. The Bulldog Mill, rated at 350 tpd, produces a bulk flotation condentrate assaying about 180 oz/T Ag and 20% Pb, from heads of about 16 oz/T Ag and 2% Pb. The circuit is straightforward with two-stage grinding to 1-5% plus 65 mesh, followed by rougher and cleaner flotation. Reagents used are Z-6, Z-11, Aerofloat 242 and Aero Promoter 404, with an Aerofroth 65-MIBC mixture for a frother. Additional information on the geology, mine and mill are available in references (1) and (2). A flow sheet for the mill and CIP plant together is attached as Figure 1. Final flotation tailings normally vary from 1.5 - 2.0 oz/T Ag. These tailings are cycloned to produce sand for underground backfill. After cycloning, the sands are repulped and given a final scavenger float. This sand scavenger recovers a small additional amount of silver which recycles back to the main flotation circuit. The tailings are recycloned and pumped to the mine or, if the mine cannot accept sand, to tailings. The majority of the silver in the flotation tailings exists in the fine fractions; cycloning upgrades the slimes and lowers the assay of the sand. The sand, after scavenging, typically assays 0.5 oz/T Ag, and the slimes assay about 3.0-3.5 oz/T Ag. From 1969 to 1976 all of the slime tailings and the sand tailings not used underground were impounded in a tailings pond located about

Jan 1, 1983

By Frank M. Howell

Creede, one of the younger major mining camps in Colorado, grew spectacularly to a town of eight or ten thousand people in the early 1890's following discovery of rich ore in the Amethyst and Last Chance mines. Gross metal production in gold, silver, lead, copper and zinc rose to a maximum of four million dollars a year in 1893. Annual production dropped to much lower figures and ranged between one hundred and five hundred thousand dollars per year during the period from 1914 to 1940. Production reached a gross of eight hundred thousand to one million dollars per year by the mid-1950's. In the years 1953 to 1957, Steven and Ratté conducted geologic investigations which were carried on as part of a cooperative program of the U. S. Geological Survey and the Colorado Metal Mining Fund Board. In a preliminary report on the Creede District, Steven and Ratté suggested that the Bulldog Mountain Fault Zone appeared to be a favorable structure to prospect. On the basis of that recommendation, augmented by independent work done by Manning W. Cox, the property was acquired, transferred to Bulldog Mountain, Inc. and financed by an O. M. E. loan. Late in 1963 Homestake Mining Company, under a Lease and Option Agreement, backed the venture by furnishing additional funds plus management.

Jan 1, 1969

By H. L. Hinds

Economic pressures to increase production to profitable levels reduced the Homestake's gravity recovery and overall recovery to un-acceptable levels. The operation of the Home-stake gravity gold circuit has increased gravity gold recovery to over 50%, improved overall recovery and increased mill availability for increased tonnage. The gravity circuit consists of three gravity gold recovery stages. The Circuit has four (4) duplex jigs, four (4) belt concentrating strakes and four (4) concentrating tables.

Jan 1, 1989

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine or the expansion of an existing mine can range from nine to 24 months, or even longer. The time frame will vary depending on whether an environmental assessment (EA) or an environmental impact statement (EIS) will be completed Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. In this paper, a two-year natural resource baseline study by Homestake Mining for the Ruby Hill Mine, Eureka County, NV, is used as a case study to describe how a properly designed and executed natural resource baseline study streamlined the NEPA process.

Jan 1, 2003

Introduction The Homestake Mining Co. has always been big on gold. After 108 years in the business, the company and its principal product are almost synonymous. The relationship continues. On Sept. 28, 1985, Homestake held formal dedication ceremonies for its newest gold mine - McLaughlin. The McLaughlin open-pit operation is located in northern California, some 113 km (70 miles) northeast of San Francisco. It lies near the boundaries of three counties - Napa, Yolo, and Lake - and a portion of its facilities are located in each. McLaughlin was originally the site of the Manhattan mercury mine that produced nearly 80,000 flasks of the quicksilver from the 1860s to 1978. At the September dedication, Homestake renamed the mine in honor of the late Donald H. McLaughlin. McLaughlin was with Homestake for nearly 60 years. He rose from exploration geologist to his ultimate positions of chief executive officer, director, chairman of the board of directors, chairman emeritus, and chairman of the executive committee. The discovery of the McLaughlin deposit occurred in 1978, the last year of operation for the Manhattan mine. Homestake geologists used a newly developed model and found surface gold at the mine site. That same year, Homestake signed an agreement with the property owner and began a two-and-a-half year exploration program. An initial discovery announcement of 31.1 t (1 million oz) of gold was made in 1980. In 1981, this was revised to 93.3 t (3 million oz), or 18 Mt (20 million st) of ore grading 5.2 g/t (0.152 oz per st). Expected mine life is 20 years. Construction began in September 1983, following the issuance of stage one permits. Start-up of operations took place in early 1985 and the first gold-silver dore bar was poured on March 4. Since then, more than 540 kt (600,000 st) of ore has been milled, producing about 1.6 t (50,000 oz) of gold. Of special interest at McLaughlin is the use of three autoclaves for gold extraction. According to Homestake, this is a first. The autoclaves are designed for a 90% gold recovery rate. Early results have proven yields at this rate and higher. Geology The McLaughlin deposit is about 1.5 km (5000 ft) long. It occurs as a wedge-shape, narrowing to a verti-

Jan 1, 1986

By J Carter, B J. Armstrong

Best practice for the submission of samples to an internal or commercial laboratory requires quality control materials to be included for the purpose of independently and comprehensively assessing laboratory performance. These quality controls include the use of certified reference materials (CRMs) and may be blind to the laboratory. Iron ore companies purchase these materials from reputable manufacturers from stock of run-of-mine materials at the appropriate grades. The international standard, ISO 17034 (ISO, 2016), specifies the competency requirements for organisations manufacturing reference materials, and includes rigorous requirements for the assessment of homogeneity, stability and establishment of property values and their uncertainties. Homogeneity is one of the most important measures of suitability for all certified reference materials and refers to the degree to which the composition and properties of a sample are uniform throughout the batch, relative to the analytical precision of the method. More specifically, homogeneity studies of candidate reference materials should be assessed for both within sample variance and between sample variance with appropriate statistical controls. The design and application of homogeneity studies are discussed as they apply to both crushed and pulverised reference materials. Crushed certified reference materials have been utilised by the iron ore industry for a number of years and provide the user with a critical assessment of variances in sample preparation in addition to analysis. Crushed reference materials are similar in presentation to an RC sample and are generally used as discrete parcels of material submitted to the laboratory from the field. Pulverise certified reference materials miss the sample preparation step and are subsampled from th delivered sachet at the point of analysis. This paper compares the relative homogeneity performance of crushed and pulverised certified reference materials by grade across key iron ore chemical constituents. Outcomes are benchmarked to the international standard ISO 9516 (ISO, 2003) for the determination of various elements in iron ores by lithium borate fusion and X-ray fluorescence. Practical implications are discussed with reference to a case study from an iron ore laboratory in the Pilbara.

Sep 18, 2023

By Xiang Sun

Microwave processing has been under continuous development as an advanced heating method in modern industries. However, problems with uneven heating still remain. Although heating uniformity is highly dependant on the properties of the materials being heated, proper furnace design to prevent uneven field distribution is another important factor. As an alternative to experimental measurements and adjustments to find appropriate furnace parameters, computer simulation is a convenient method for modeling, understanding, and improving the uniformity of microwave heating. This paper discusses current modeling technologies as well as applicable techniques for improving microwave heating uniformity. The purpose is to give a basic understanding on how to find, analyze, and minimize the problems associated with uneven heating in microwave processing.

Jan 1, 2006