Search Documents

By D. J. R. Ras

A sub-level open stoping method is being used to mine the massive deposits at TARGET Gold Mine which uses cemented tailings to backfill the stopes. This requires the construction of bulkheads to contain the freshly placed backfill, capable of resisting the hydraulic pressure imposed by filling. The bulkheads must contain an 8 metre head of backfill slurry within 48 hours and withstand the force exerted by a 35 metre load of consolidated fill at a maximum estimated fill relative density of 1.9. After a variety of methods of construction were evaluated, it was decided to construct the bulkheads using the low density, fast-setting foamed cement-based product TEKSEAL HS manufactured by MINOVA RSA. The cement foam is contained between low-cost steel and fabric brattices which are easy to construct, using a method specially developed for the TARGET bulkheads. The paper will describe the design, trialling and construction of the bulkheads, and results obtained to date.

May 1, 2007

By Hiroshi Tabuchi, Akihiko Takahashi

"High strength aluminum matrix composites were prepared and studied using as reinforcement newly developed nearly mono-dispersed a-alumina single crystal particles each of which has a regular polyhedral shape. The composites were formed by centrifugal casting using aluminum casting alloys (Al-Si and Al-Cu-Mg) as the matrices, followed by heat treatment. The volume fraction of the alumina particles was as high as 60%. The same matrix composites reinforced by conventional crushed fused alumina particles were similarly prepared as the reference. The bending strength and tensile strength of the Al-Cu-Mg matrix composites reinforced by the novel alumina particles of 10 µm in average diameter are as high as 1020 MPa and 560 MPa, respectively, which are higher than those of the conventional alumina composites. Furthermore, the bending strength of the novel alumina composites degraded less than that of the conventional alumina composites after thermal fatigue tests. The number of cracks in the matrix seemed to influence the thermal fatigue property because many cracks were observed in the conventional alumina composites, whereas only a few cracks were observed in the novel alumina composites. This was confirmed by SEM observation of the sample composites before and after the thermal fatigue tests.IntroductionAluminum matrix composites strengthened by dispersed reinforcements are of interest for various applications due to their improved properties, such as high specific strength and stiffness, wear resistance, etc .. A large number of investigations have been made concerning fabrication processes and properties of these composites. With regard to the fabrication processes, powder metallurgy has been well-known as a solid phase process, and recently many liquid phase processes such as a compocasting, a squeeze casting, the Lanxide process, and the Osprey process have been studied and developed.(1)"

Jan 1, 1998

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By G. Hergert

SUMMARY Three gradients have been identified in regard to the average horizontal ground stress increase with depth. [S (0-900 m) = 9.86 MPa + 0.0371 MPa/m SHa (900-2200 m) = 33.41 MPa + 0.0111 MPa/m SHae (extreme)= 12.36 MPa + 0.0586 MPa/m] The extreme stress values are not caused by mining geometry and are of limited extent only. In some cases geological disturbances like faults and rock type boundaries suggest an explanation but in other cases the unusually high stresses cannot be explained readily. It is interesting to note that in the same locations the vertical stress components are very much higher than those derived from overburden weight and that the vertical stress gradient is similar to the gradient obtained from the extreme horizontal stress components. INTRODUCTION Ground stress determinations have been carried out in mines in Ontario and Manitoba, Canada, over more than a decade (Herget, 1980). Most of the sites are located in the Superior and Southern Tectonic Province of the Canadian Shield, which consist of Archaen and Proterozoic rocks comprising volcanics, metamorphosed sediments and granites. The youngest orogenic deformation occurred during the Grenville Orogeny (955 million years ago).

Jan 1, 1982

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By S F. Simmons, J Fleming

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyilite alteration zone forms an upward flaring cone, largely hosted within a breccia body that cross-cuts the Co, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid-mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By Simmons SF, Fleming J

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyllite alteration zone forms an upward flaring cone, largely hosted within a breccia body that c ross-cuts the Cu, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By Kevin Stuffle, James E. Sharp, Sean Premeau

Two process enhancements for the biological oxidative pretreatment of sulfidic gold ore for subsequent treatment with cyanide are discussed. These are the use of a high areal density ring and pin packing (BioBalls™) as substrate, and the use of a novel biological ferric generator. The BioBall™ packing when coated with concentrates for heap leach processing offers higher areal densities, while leaving more open volume for fluid flow than more commonly used substrates such as aggregate. An oxidation rate study was performed on crushed auriferous arsenopyrite whole ore to demonstrate the benefits of using the packing. The auriferous arsenopyrite grading 2.9% Fe and .212 OPT gold was 50 percent oxidized in 24 days. The biological ferric generator is a passive air-side trickle bed reactor that efficiently converts ferrous to ferric in a process stream. Conversion rates of .8g/L h ferrous to ferric are routinely obtained. Although the biologically generated ferric solutions have not yet been tested on gold ores or concentrates, prior work has demonstrated that the high ferric solutions which will result in rapid oxidation of sulfidic gold ores or concentrates.

Jan 1, 1997

A narrow (200-300m) zone of amphibolite facies metamorphic rocks underlies the Papuan ophiolite near the Musa-Kumusi divide, SW of Popondetta, Oro Province. The amphibolite rocks are bounded up-section, to the NE, by peridotite and gabbro of the ophiolite; and down-section, to the SW, by mafic greenschist, which in turn overlies blueschist facies mafic schists of the Emo Metamorphics.Amphibole compositions within the narrow contact zone show a strong chemical zonation which reflects a steep thermal gradient, with maximum temperatures >800¦C at the peridotite contact. The zonation is recorded in Ti content and A-site occupancy, relative to Al'¦

Jan 1, 1994

Carbonate-hosted massive sulfide ores of the American cordillera compose a distinctive genetic class. Discordant fea-tures of occurrence together with measured high-temperatures of formation indicate their essential epigenetic character and close spatial association with centers of thermal activity during evolution of the cordillera. Their metallogenic character is complex from region to region: Cu-Zn-Pb-Ag, Pb-Zn-Ag, and Cu-Zn-Ag-Au represent extremes of composition and each may be identified with specific terranes of occurrence, notwithstand-ing an inferred common process of formation. Beyond the presence of a thermal center, other controls that may be identi-fied include apparent but obscure properties of primary perme-ability or chemistry of hosting strata, and secondary controls are imposed by stratigraphic differences in which permeability is strongly contrasted. Structures that act as channelways may be identified in some instances. Notwithstanding their intrinsic value, search for these ores is difficult and requires the solution of complex geochemical and three-dimensional geometric problems.

Jan 1, 1990

By S Hapugoda, A Edenton, L Lu

The blast furnace cohesive zone has a profound impact on hot metal productivity and quality, fuel consumption, operational stability and the lining life of the blast furnace. The high temperature properties of ferrous burden materials determine the configuration and location of the cohesive zone and have therefore attracted particular attention. While numerous standard testing methods are in use to assess the quality of ferrous burden materials for the blast furnace, these simple tests are generally conducted under fixed conditions, which often represent the extreme situations encountered by the burden materials in the blast furnace. Furthermore, none of these simple tests provides information on the high temperature properties of the burden materials, such as their softening and melting properties. CSIRO is equipped with a fully computerised testing facility to characterise the high temperature properties of ferrous burden materials under realistic conditions similar to those encountered in the blast furnace. This paper will first review the CSIRO softening and melting test method and then discuss the softening and melting properties of a variety of blast furnace burden materials, including sinter, pellets and lump ore, and their implications for blast furnace operation.

Nov 8, 2021

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By M. Yoshida, S. Hanada, T. Takasugi

"A study has been conducted to examine the effect of ternary alloying elements on high temperature deformation of the C15 NbCr2 based intermetallics in Nb-Cr-X (X=V, Mo and W) alloy systems, which have attractive properties as high temperature structural materials. The high temperature deformation of the C15 NbCr2 intermetallics can be improved by two alloying methods. One method is based on geometrical consideration for site occupation and atomic size factor of component elements and additive elements in the single phase C15 lattice; addition of Mo and V can promote dislocation movement without introducing significant hardening. The other method is based on microstructural modification through ternary alloying; moderate addition of these elements results in a variety of duplex microstructure consisting of the C15 phase and bee solid solution without forming any intermediate phases, and can enhance the high temperature deformability. Particularly, alloys with duplex microstructure equilibrating with Cr-rich bee solid solution is shown to exhibit superior deform ability. Also, lattice property of the additive atoms in the C15 structure and phase relation between the C15 structure and the bee solid solution are investigated by OM, XRD, TEM and ALCHEMI observations and then discussed in association with observed mechanical behavior.IntroductionLaves intermetallics with AB2 stoichiometry belong to the largest group in a large number of intermetallics with various kind of crystal structures, and have a variation of the cubic CIS, the hexagonal C14 and the dihexagonal C36 structures, depending on stacking sequence of XYZ type, each of which consists of four interpenetrating atomic layers (1-3). Some of the Laves intermetallics have good functional properties and therefore are considered to be used as, for instance, magnetic materials, magneto-optical materials, hydrogen storage materials and superconducting materials (2). Also, the Laves intermetallics are considered to be good candidate as high temperature structural materials operating at high temperatures and in severe environment because they have high melting point, low density, and potential resistance to corrosion and oxidation. However, the Laves intermetallics are very brittle at low temperatures because they consist of complex crystal structures similar to many other intermetallics."

Jan 1, 1996

Few, if any, reliable thermodynamic data are available for the activity of tin oxide in slags. In this work, the activity of the oxide in silica saturated iron silicate slags has been measured at 1573 K using the equilibrium Sn (alloy) + Y2O2-SnO (slag).Slag and a Ag-Sn alloy were sealed in a zirconium oxide crucible to prevent the escape of volatile tin oxide, and the oxygen pressure at equilibrium measured in situ using the zirconium oxide as a solid electrolyte. Activity of tin was calculated from known data for the Ag-Sn system and activity of tin oxide calculated from free energy data. The results have been extrapolated to predict the industrially important distribution of tin and iron between Fe-Sn alloy and iron silicate based slags.

Jan 1, 1983

By Jerry Gagnon, Matt Burr, Timothy Ellis, Abbas Mirza, Larry Webb

"The mechanical properties of RSR anode alloys (lead-calcium-tin, 009+ and lead-strontium-tin) were investigated as a function of time with an objective of developing lead anodes for use in high temperature electrolytic processes such as in copper liberator cells and in cobalt and nickel electrowinning. At a temperature of 70 oC, the mechanical properties of rolled RSR lead-calcium-tin (PbCaSn) alloy currently used in copper electrowinning decreased gradually while the mechanical properties of rolled RSR lead-strontium-tin (PbSrSn) decreased relatively quickly and stabilized at low strength levels. Cast PbSrSn started off as the weakest alloy but its properties remained stable with time. Rolled RSR 009+ anode alloy showed improvement in ageing properties over the other alloys tested. However, its mechanical properties did not stabilize in the study timeframe of 284 days. Further investigations are planned to study the effect of alloying elements on mechanical properties of RSR 009+ anode alloy over several years as a function of time at 70 oC. The mechanical properties will be evaluated to determine the time at which they stabilize. Comparative plant trials with rolled RSR PbCaSn and RSR 009+ will also be performed in copper liberator cells and in cobalt and nickel electrowinning tankhouses to determine their mechanical and electrochemical performance at temperatures of 65-75 oC.INTRODUCTIONLead-based alloys are the primary anodes used in the electrowinning of copper, zinc, nickel, cobalt and manganese from sulfate-based aqueous systems. Lead anode technology has evolved over the years migrating from pure lead and lead-antimonial alloys to the present day PbCaSn alloys for copper and PbAg and PbCaAg alloys for zinc electrowinning (Prengaman, Ellis and Mirza, 2010). It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new lead anode alloys and production processes for lead anodes to be used in copper electrowinning, the industry still has some unresolved issues. These relate to the necessity of having higher mechanical properties especially for the lead anodes in liberator cells in copper electrorefining and for cobalt and nickel electrowinning as these tankhouses operate at temperatures of 65-75 oC compared to 40-45 oC in case of copper electrowinning."

Jan 1, 2016

By Leiv Kolbeinsen, Stian Seim, In-ho Jung

"The current work presents new experimental data in the iron-unsaturated region of the FeTiO3-Ti2O3-TiO2 slag system. The samples are prepared by melting pure reactants in a high frequency induction furnace that employs a cold crucible. A similar experimental set-up has been described in literature and proven suitable to investigate high titania slags. The FeO content of the samples range from 3.7 to 21.8 wt% and the Ti2O3 content range from 3.6 to 30.1 wt%. The liquidus temperatures of the samples are measured in-situ by a spectropyrometer and range from 1450 to 1645 °C.In addition, an improved thermodynamic database for the FeO-Ti2O3-TiO2 system has been developed. Ternary parameters have been included and optimized to fit previously published experimental data. This optimization minimizes the discrepancy between experimental data and thermodynamic calculations as previously discussed in literature. New liquidus projection plots are proposed for the FeO-Ti2O3-TiO2 and the FeTiO3-Ti2O3-TiO2 systems.IntroductionIlmenite (FeTiOs) smelting is a relatively small industry world-wide. However, a reasonable focus on the process has been applied in Norway due to the location of one such smelter in Tyssedal, which is located in the western part of Norway. The process is essentially carbothermal reduction, where most of the iron in the ilmenite is reduced to its metallic state, and the titanium oxide is concentrated in the slag product. The metallic iron is sold as a high purity pig iron and finds applications in cast products. The slag concentrate is further processed for the production of TiOvpigment and/or titanium metal. This further processing can be performed through different routes according to the purity of the slag concentrate."

Jan 1, 2012

By Mance G

Today there are many different techniques of soil remediation used in Australia and throughout the world. This paper considers the thermal desorption remediation technique and, in particular, the application of high temperature filtration to the process. The thermal desorption technique involves the treatment of hydrocarbon (oil, petrol, etc) contaminated soil. The process involves heating the soil in a retort or kiln to drive off the volatile organic contaminants. The exit gas stream from the retort is subsequently passed through an after burner to thermally oxidise the hydrocarbons. This technique produces soil and combustion gas streams which are free of hydrocarbons. Due to the heating and agitation of the soil within the retort, soil particles become entrained in the hot gas stream. To avoid the blockage and fouling of the system's interim ductwork and the afterburner, high temperature filtration technology has been applied to remove these soil particulates without cooling the gas Stream.

Jan 1, 1995

By Javier Antoñanzas, Juan Carlos Múgica, Lourdes Yurramendi

The gasification of wastes containing an organic fraction is usually performed at low-medium temperature using different kind of catalysts. The off gas obtained is a mixture of carbon oxides, mainly carbon monoxide, and hydrogen and can be used for different energetic applications. The main problem is the production of tars in the off gas that has to be separated from the valuable gas flow and, finally, treated separately. An interesting alternative is the partial or total treatment of organics at high temperature. In this case, the off gas contains a higher content of hydrogen and elemental carbon as particulate matter. The energetic source to obtain a temperature in the range of 1,000 - 1,200 ºC is obtained by a plasma torch. In order to make de process attractive, an important issue to be considered is to commercialize the carbon obtained for different industrial applications.

Jan 1, 2008

By Shengli Wu, Jinming Zhu, Wei Huang, Xinliang Liu

The sinter of high basicity would interact with lump ores or acid pellets in the cohesive zone of blast furnace due to the difference of chemical composition and micro structures. The results of this work showed that the softening-melting properties of lump ores and acid pellet would be obviously improved by the high temperature interaction. However, the high temperature interaction index (INI) would be influenced by many factors, such as chemical composition, porosity, interaction interface and so on. The INI between sinter and porous limonite lump ore (L-2) was much higher than that of dense hematite lump ore (L-1) and acid pellet (P-1). In addition, though the softening and melting properties of L-2 were poorest in respective iron ores, the softening and melting properties of integrated burden B (consist of sinter and L-2) were not worse than other integrated burdens due to the strong high temperature interaction.

Jan 1, 2015

By N. Can

Kinetics and mechanism of the chemical interactions between Si3N4 and TiC were investigated by isothermally reacting samples under nitrogen and argon atmospheres at temperatures between 1600°C and 1700°C? The initial composition of the powder compact contained 20, 30 and 40 volume per cent TiC? Kinetic analysis were performed by measuring mass losses and composition of the titanium carbonitride (TiC1-xNx) at predetermined time intervals? It was found that in the Si3N4-TiC system the degree and rate of the reactions increased with increasing temperature and content of TiC in both nitrogen and argon atmospheres? Si3N4 in the presence of TiC was stable in nitrogen atmosphere and the reactions were confined to Si3N4/TiC and TiC/N2 interfaces? At both interfaces interchange reaction occurs by simultaneous diffusion of nitrogen towards the centre of the particle and desoprtion of carbon in the opposite direction resulting in formation of titanium carbonitrides with various compositions? Reaction products under nitrogen atmosphere were B-SiC, TiCl1-xNx and N2? The maximum "x" value in TiC1-xNx was found to be 0?67 under nitrogen atmosphere? Si3N4 was found to be unstable in argon atmosphere in the presence of TiC and dissociated into liquid silicon and nitrogen gas within approximately four hours of reaction time, depending on temperature? The reaction mechanism in the initial stages of the interaction between Si3N4 and TiC under argon atmosphere proceeds similar to reactions under nitrogen atmosphere? However, considerable amount of Si3N4 dissociates within the first half hour? Liquid silicon aggressively attack both TiC1-xNx and unreacted or partially reacted TiC particles through cracks and pores and diffuses into interier part of the particle forming liquid solutions? After this stage, reactions under argon atmosphere proceeded according to Si-Ti-C ternary system?

Jan 1, 1999