Search Documents

By C. E. Corson

Discussion of the Paper by C. E. Corson, which was presented at the London Meeting, July, 1906. (See Bi-Monthly Bulletin, No. 11, September, pp. 725 to 742.) ALBERT SAUVEUR, Cambridge, Mass. (communication to the Secretary*) :-On close examination I think it will be found that the evidence by which Mr. Corson claims to have shown the inaccuracy of a statement I made a few years ago, is far from convincing. This statement is:- "Hot work, as such, has no influence upon the structure of the metal. Indirectly, however, by retarding crystallization until a lower temperature is reached, it may influence its structure most decidedly ; but the same results could be accomplished by heat-treatment alone, i.e., by reheating the unworked metal to the temperature from which the unworked piece was allowed to cool undisturbedly." The Metallographist, vol. ii., p. 267 (under the head of "Changes of Structure Brought About by Work"). Of the two pieces of steel tested by Mr. Corson, one was worked and finished at a " cherry red " and ' the other reheated to a cherry red, and the assumption was made that, in both cases the temperature was about 715° C., although no pyrometric device was used to record it. The possibility of considerable difference in temperature alone is so great as to invalidate Mr. Corson's inferences. The apparent temperature, moreover, is so close to the critical point of the steel as to render any conclusion very hazardous. -It is not at all evident that the annealed piece was reheated past its critical point, in which case reheating would have had practically no effect. Nor is it evident that the piece forged and finished at a cherry red was not actually below the critical point, which, by definition, I have called cold worked. Mr. Corson's explanation that " Under proper reheating, on the other hand, the steel becomes a solid solution from which crystals of approximate homogeneity and uniform size may separate" will not be readily understood.

Jan 1, 1907

By T. J. Lutz, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Of the in-use RAs, over 95% are mobile RAs with the remainder being built-in-place (BIP) RAs. Heat/humidity buildup has been one of the major concerns with mobile RAs. For BIP RAs, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP RAs, the National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP RA with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated, or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP RA. The results show that the air supplied to a BIP RA may require heating and cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 70°F and a humidity that reached 90 %RH, providing 55°F dew point air was able to keep the internal apparent temperature below the mandated 95°F. Results for each test case are presented. INTRODUCTION The Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines since 2008 [1]. MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force recommended an apparent temperature limit of 95°F for RAs [2]. In 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 95°F inside an occupied RA [3]. The apparent temperature is calculated using both air temperature and relative humidity [4]. To determine if their RAs meet the apparent temperature limit, RA manufacturers have been performing 96-hour-long heat and humidity tests in laboratories. During these tests, a heat input of 117 W (400 BTU/hr) per person is used to represent the metabolic heat of a single miner [2]. The heat generated by the RA’s carbon dioxide system is also accounted for in testing. To account for this heat, 50 W (170 BTU/hr) of heat per miner is used for a lithium hydroxide scrubbing system, or 30 W (100 BTU/hr) of heat per miner is used for a soda lime scrubbing system [5]. In these tests, air velocities around the RA are minimized to represent the worst-case scenario of an interruption in mine ventilation that might occur in a mine disaster."

Jan 1, 2017

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By G. C. Tipper, A. P. Deane, A. G. Myers

SCHEME DESIGN London’s Heathrow Airport, as the world’s busiest international airport, is missing one vital aspect - a dedicated rail link which connects directly to the city. All this is about to change with the construction of Heathrow Express - a fast, high quality rail service between the airport and the centre of London. It was recognised in the mid 1980s that if Heathrow was to accommodate the forecast growth in passenger numbers and the resulting increase in road traffic, a dedicated airport rail service would be vital. The main access into the centre of Heathrow is via a road tunnel with a direct link to the M4 motorway. The airport has introduced a number of traffic management schemes, but these can only achieve so much benefit. Growth in air passenger traffic is predicted to continue at an average of 4% per annum well into the next century and it was clear that significant investment was needed. Heathrow Express at a cost of over £350 million will provide this when it starts its service in June 1998. The business case for the scheme is based on a rider ship of around 15% of air passenger traffic. The initial Heathrow Express service will be based on four trains per hour, up to 8 car train lengths, providing a high speed non-stop service between the airport and central London in just 16 minutes. Initially a joint venture between the British Railways Board and Heathrow Airport, by mutual consent of the two parties, Heathrow Airport recently purchased the British Railways Board share making this one of the largest private sector rail projects currently under construction in the UK. Leaving Paddington, the main rail terminus in West London, Heathrow Express trains will travel 12 miles on the newly electrified line to airport junction, north of the airport. At this point they will leave the mainline to enter a 5 mile tunnel section that runs underneath the heart of the airport. The railway companies are responsible for track work, signalling and electrification of the 12 mile main line section including a grade separated junction over the main tracks for the Great Western Railway which links London and South Wales. Heathrow Airport is re-

Jan 1, 1997

By Paul Suver

"The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.CLSCW Description:Closed end steel pipe of varying outer diameter (O.D.) is installed by various technologies at varying depths depending on subsurface geology. The wells are arranged as stand alone wells or in groups joined in parallel or in series or in a combination of both. These pipes may also serve a dual function as foundation supports, deep foundation pile, anchors or earth retention components. These wells are then internally coated to minimize corrosion. The wells are then plumbed and capped to create a vessel equipped with a supply and return water line.The stand alone well or group of wells is then used as a ground heat exchanger for a ground source heat pumps located in or around the building.The ground source heat pumps provide heating and cooling to the building either with a traditional ducted distribution system or with radiant heating and cooling. These systems can reach efficiencies three times greater than traditional gas fired heat sources and five times greater than traditional air conditioning sources."

Jan 1, 2017

By Paul Suver

The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By Robert E. Wood

Engineers have known for some time that the efficiency of filtering iron ore concentrate slurry can be significantly improved by pre-heating the slurry ahead of the filters. However, heating such large quantities of dense slurry by conventional means has proven to be inefficient and high-maintenance. Recently though, submerged combustion was considered by Altos Hornos de Mexico SA (AHMSA), an integrated steel producer in the state of Coahuila, Mexico, as a means of pre-heating their iron ore concentrate. The company toured many iron ore facilities in Brasil and Labrador, reviewing their heating processes, and concluded that submerged combustion could provide a competitive advantage through operational efficiency and lower capital cost than steam boilers. Inproheat was retained by the company to design and manufacture a SubCom slurry heating system to heat 403 m3/h of iron ore concentrate slurry from 25°C to 60°C. The 60GJ/h SubCom system consists of five natural gas combustion chambers mounted in an iron ore concentrate storage tank. The system features a heat recovery unit whereby the exhaust gases are used to preheat the incoming slurry stream, giving the system an overall thermal efficiency of 95%. As a result, the steel company expects to realise significant improvements in filtering efficiency which will enable them to increase the capacity of their pelletising plant without installing additional filters.

May 1, 2010

By C. M. Young

BITUMINOUS coal piled in heaps or bins frequently undergoes a process of spontaneous heating as the result of the absorption of oxygen. It seems probable that the first absorption of oxygen by coal which has not previously been exposed to the air may occur as a condensation or a combination of oxygen in some form which does not result in the production of carbon dioxide, but slow combustion soon begins. The absorption of oxygen is accompanied by an increase of temperature, and this by in increased rapidity of absorption; hence the dangerous condition proceeds from bad to worse, until the kindling point is reached, unless the process is interrupted. A dangerous rise of temperature can be prevented by excluding oxygen, by increasing the bulk of coal in proportion to its surface exposed, or by circulating enough air to dissipate the heat produced. The storage of coal, in practice, varies from almost complete exclusion of oxygen, by storing under water, to such freedom of access as exists when the coal is stored in open piles. Oxygen available for absorption by coal is supplied by the air in the interstices between lumps and by additional air which may enter the pile through circulation. The size, of the coal largely affects both of these supplies; for if the fragments a re small the spaces between them constitute a small percentage of the total volume, and little oxygen will be available unless the circulation of air brings in a fresh supply, while with large fragments the percentage is relatively large; circulation also is much easier through a pile of coarse lumps. In the case f lump coal, although a large amount of air may be present, the exposed surface is comparatively small and there is little opportunity for the absorption of oxygen to so rapid as to cause dangerous heating. Attempts have been made to prevent heating by allowing a sufficient circulation of air to carry off the heat generated; obviously this method cannot be applied to fine sizes nor mixed sizes.

Jan 2, 1918

By R. A. Sullivan

I T IS one of the unwritten policies at Preston Mines that we examine closely any method or tool that will help us in our constant battle against rising costs. It is our personal conviction that most work methods can be improved. Therefore even though the job went well yesterday, it does not necessarily follow that it should be done by the same method today. With the arrival of the natural gas pipe line in the Porcupine area it was obvious that we would have to take a good look at the possibilities of using this source of fuel for plant heating. • Steam presently generated at Preston is for heating purposes only, no process steam being required. Prior to the fall of 1960, the heating plant consisted of two low pressure, coal-fired, fire-tube boilers, operating at an approximate pressure of 14 pounds per square inch. These boilers were underfed by stokers and could be operated either singly or together. ~o. 1 unit was a horizontal return tubular boiler, registered at 100 h.p. No. 2 unit was a fire-box boiler, registered at 75 h.p.

Jan 1, 1962

By C. Y. Wen, H. O. HOPMAN

l. INTRODUCTION. IN casting a thermal balance of the heat generated and absorbed in a blast-furnace treating lead-, copper- and similar non-ferrous ores, assumptions have always to be made for the values of the heat of formation of slag. ? Considering that the larger part of the charge introduced into the furnace comes out in the form of slag, the significance becomes apparent of a lack of heat-values for the singulo-silicate, which is the type of slags commonly made. The aim of the present investigation is to supply these heat-values as far as possible with the apparatus and the time available. The heats of formation of the ferrous and manganous bi-silicates have been determined by Le Chatelier; 1 those of some silicates other than iron and manganese by Tschernobaeff:2 finally Richards 3 gives a figure for a copper blast-furnace slag of known composition. The existing data and those resulting from the present investigation are assembled in Table VI. II. MATERIALS USED. The materials used in the experiments were silica, ferrous oxide, and calcium carbonate. Silica.-The silica sold in the market as chemically pure usually contains small amounts of magnesia, lime, and alumina, and is therefore not suited for the work. The pure material was obtained from clear quartz crystals from Arkansas, broken in a diamond mortar and ground in an agate mortar to pass 1 Comptes rendus, vol. cxx., p. 623 (1895); vol. cxxii., p. SO (1896). 2 Revue de Métallurgie, vol. ii., p. 729 (1905); Electrochemical and Metallurgical Industry, vol. iv., No. 2, p. 72 (Feb., 1906). 3 Electrochemical and Metallurgical Industry, vol. v., No. 7, p. 266 furls?, 1907;) ; Metallurgical Calculations, vol. iii.,.pp. 474, 475 (1908).

Jul 1, 1910

By Kampe. S. L., Baker. Andrew H., Tony Zahrah

"Experimental heats of reaction for the formation of several Al3Ti + TiB2 intermetallic composite formulations have been determined utilizing bomb calorimetry. To overcome the kinetic constraints and achieve ignition in these formulations, a boron (B)/potassium nitrate (KNO3) initiation aid was incorporated within the blended reactant compact. The heat contribution from the initiation aid was regressed to provide estimates of the heat of reaction of the nominal formulations. Powder x-ray diffraction was utilized to identify the products of the reaction and discern any differences between the predicted equilibrium products of the formulation and the actual products.IntroductionReaction synthesis is a technique for the creation of ceramics, intermetallics, and in-situ composite materials [1]. Reaction synthesis is defined by its self, propagating mechanism, where the energy liberated from a localized reaction within a green powder compact is enough to carry the bulk reaction to completion. Achieving a self, propagating state can be achieved in variations of two primary methods of initiation: uniform volumetric heating and directional propagation [2].Uniform volumetric heating involves subjecting a green compact of the unreacted formulation to uniform heating in a furnace to encourage diffusion to initiate the reaction (Figure 1a) throughout the bulk material. Directional propagation utilizes a point heat source at one section of a green compact of unreacted formulation (Figure 1b). The localized exothermic reaction at one point in the compact then initiates the reaction in the section of the compact adjacent to it and fully propagates throughout the entire compact until completion. Initiation of the localized reaction is generally associated with the melting of the constituent with the lowest melting point, with instantaneous initiation of the reaction usually occurring close to that melting point [1]. This melting point can be high in some systems of interest, such as the titanium (Ti) and boron (B) system in equation 1:"

Jan 1, 2011

By Ellsworth Spencer

Noise induced hearing loss continues to afflict workers in many occupational settings despite longstanding recognition of the problems and well-known methods of prevention and regulations. Sound levels associated with heavy construction equipment range from 80 to 120 dB(A) and power tools commonly used in construction produce sound levels up to 115 dB(A).(1) The focus of this research was to determine the noise exposures of heavy construction equipment operators while documenting the workers’ tasks, (i.e. hauling, moving, and/or pushing construction material). Time-motion studies were performed at the construction sites and were used to correlate the noise dosage with the work performed by equipment operators. The cumulative dose for the operator was then plotted with references to work tasks, to identify the tasks that caused the greatest noise exposure. Three construction sites were studied for this research located in the western Pennsylvania and eastern Ohio areas. The types of construction equipment studied included asphalt pavers, backhoes, bulldozers, compaction equipment, excavators, haul trucks, telehandlers, and wheeled loaders. The results showed that bulldozer operators consistently had the highest noise exposures, ranging from a NIOSH REL (Recommended Exposure Limit) dose of 844% to 25,836% and an OSHA PEL (Permissible Exposure Limit) dose of 139% to 1,397%.

In early June, Rio Tinto?s chief executive officer Tom Albanese said that he expected demand for iron ore, aluminum and copper to double in the next 15 years. Driven by global industrialization and urbanization, Albanese said during his company?s annual general meeting that to meet the demand in 2030, the additional supply required will be equivalent to replicating the iron ore output of Australia?s Pilbara region every five years, adding another aluminum production complex the size of Canada?s Saguenay every nine months and developing another copper mine the size of Escondida, in Chile, each year.

Jan 1, 2010

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Accidents occur when least expected, from sources that we rarely anticipate and with outcomes that can vary greatly. Anyone who has ever been involved in an automobile accident knows, the transition from driving comfortably and safely down a highway to being involved in a potentially life-threatening situation can occur in a heartbeat. Accidents on the job are no different. The mining industry has a relatively small number of electrical injuries, compared to industries such as construction or agriculture, due to the small total employment in mining. Mining does, however, have one of the highest occupational electrocution rates of any U.S. industry, at 2.8 for every 100,000 workers per year. This is approximately four times the average for all industries. Data from the Mine Safety and Health Administration (MSHA) shows that 75 electrical fatalities occurred in the mining industry between 1990 and 1999. Of these, at least 17% involved high-reaching mobile equipment that contacted overhead power lines.

By J. Hoover

"IntroductionThis chapter will discuss the operational and maintenance aspects of a heavy media cyclone circuits as applied to coal processing and using magnetite as the media. It deals with heavy media bath separators in terms of types of media, equipment, circuits, media recovery, maintenance, and product handling. It will detail heavy media cyclone operation and supplement the previously described topics.The heavy media cyclone was first developed in the Netherlands by the Dutch State Mines in 1945. A cyclone plant was not built in North America until 1961. Traditionally, heavy media cyclones have been used to treat size fractions between 1lz in. (12 .6 mm) and 35 mesh (0.5 mm). High maintenance related to heavy media bath separators has recently prompted some plants to crush all raw coal to minus 2 in. for treatment in heavy media cyclones.The heavy media bath separators utilize only the force of gravity to make the separation between heavy and light particles. This requires lengthy retention time which can lower capacity and also is inefficient for finer particles. A heavy media cyclone utilizes centrifugal forces which are 20 to 200 times greater than the force of gravity. This means the separation between coal and the impurities occurs very quickly, therefore a low retention time is required allowing cyclones to have high tonnage capacities. Also these greater forces allow better separation for the finer particle sizes.Heavy media cyclones are now widely used to produce both metallurgical and thermal coal. Work is in progress to reduce magnetite consumption, extend wear life, increase tonnage capacity, improve separation efficiency and automatically control these cyclone circuits."

Jan 1, 1989

By T. P. Meloy

Current coal cleaning technology uses heavy media (HM) for the recovery of coal in particles larger than 1/16 of an inch. Through the use of float sink measurements of the feed and products to commercial HM unit operations, a selection function, sometimes called Tromp curve in the coal industry, can be computed. Since the selection function is a plot f the probability of a particle appearing in the float versus the particle density, the slope of the curve will be sharper at the point where the particle has a 50% chance f appearing in the float. Thus, the separation will be better. Fine-tuning a unit operation or a circuit of unit operations requires that the selection function be accurately known. By current practice, it is difficult to obtain an accurate measure of the slope because, when the selection function is plotted versus density, the data forms an S-shaped curve which lacks data points near the 505 point of the curve. This lack of sensitivity in measuring the slope means that small recovery improvements cannot be detected; thus, only large improvements are measurable. Since most engineering improvements are small when individually considered, but large when aggregated ever many small improvements, this lack of measurement sensitivity rules out the slew march toward improved efficiency. This paper presents a method of analyzing heavy media selection functions resulting in a far more effective measure of the selective function slope. Furthermore, this improved method is applied to a number of industrial coal cleaning plants for both heavy media and heavy media cyclones. Using the work of Hudy (1968), and Deurbrouck and Hudy (1972), selection functions for individual unit operations in each plant are calculated as a function f particle size as well as density.

Jan 1, 1982

By Roshan B. Bhappu, Thomas J. Lien

The DYNA WHIRLPOOL Processor (DWP) is a cylindrical dynamic heavy media vessel. It is used to beneficiate fine ore sizes from one and one-half inches in diameter down to 65-mesh. Process units available treat up to 80 tons per hour. Units can be manifolded for higher capacity plants. Finely ground magnetite and ferrosilicon are used for media. , Installed capital costs are from $4,000 to $6,000 per ton hour of feed. Operating costs are from $0.30 to $0.50 per ton of feed. The DWP is used to beneficiate metallic and non-metallic ores and coal. The OCC Vessel is a static heavy media separator used to beneficiate coarse ore up to six inches in diameter and auto scrap. Process units available treat up to 300 tons per hour.

Jan 1, 1978

By Vas P. Srinivasa

This paper examines the role of the heavy media separator in the mineral industry. Procedures used in selecting the separating vessel, developing the process flowsheet, and designing a heavy media circuit are discussed. For comparative purposes, the capital investment and operating costs of different types of operation are included.

Jan 1, 1981

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978