Search Documents

By Zay Jeffries

IT has been known for a number of years that certain aluminum alloys could be hardened by quenching from a temperature of about 500° C. Immediately after quenching the total increase in hardness is not marked, but the hardness increases gradually so that after about 4 days, it has reached a maximum. The actual increase in hardness probably continues for weeks or even months, but in order to detect the differences after 4 days, it is necessary to make tests at rather long intervals. So far as is known to the authors, Alfred Wilm was the first to discover these properties in aluminum alloys.1 The aluminum-copper alloys are amenable to this treatment and the addition of magnesium makes the heat-treatment effect more pronounced. Until recently heat treatment of aluminum alloys has been confined to the worked alloys in the form of sheet or extruded products. The alloy that has been most used in this connection is known commercially as duralumin and has about the following composition: copper not exceeding, 6 per cent.; magnesium not exceeding, 2 per cent.; manganese not exceeding, 1 per cent.; commercial aluminum,2 balance. A typically good alloy in this range consists of: copper, 4 per cent.; magnesium, 0.5 per cent.; manganese, 1 per cent.; commercial aluminum, balance. This alloy can be rolled into sheets or extruded; and in this condition it can be heated in the ordinary furnace atmosphere to a temperature near 500° C. and quenched in water. After about 4 days it will have the following physical properties: tensile strength 55,000 to 60,000 lb. per sq. in. (3866 to 4218 kg. per sq. cm.); elongation in 2 in., 15 to 20 per cent. No harmful effects of the furnace gases or even the air, if the heating is affected in an electric furnace in an air atmosphere,

Jan 9, 1919

G. K. BURGESS, ? Washington, D. C.-At the Bureau of Standards it was decided, in order to study the high-aluminum end of these curves, that efforts should be made to prepare pure aluminum, and the promise of getting aluminum, practically free from the two elements that have such great effect in very small quantities, namely, silicon and iron, and which

Jan 12, 1919

By D. B. Hobbs, L. W. Kempf, R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17S and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings. REVIEW OF LITERATURE The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

Jan 1, 1928

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

By Ragnhild E. Aune, Shahid Akhtar, Reza Beheshti

"The potential use of Black Dross (BD) as a raw material for the production of refractories, fluxing agents and glasses is the main motivation of the present study. Heat treatment experiments were carried out in Ar, and under reduced pressure (20 Pa), to evaluate the salt removal efficiency. The chemical composition of the BD after heat treatment was investigated by SEM-EDS and XRD analyses. Based on the present results, it is established that the salt starts to evaporate at ˜1273 K in Ar, and under reduced pressure. The salt removal efficiency in a 20 g sample was found to increase in both cases as a function of time and temperature. Moreover, in Ar the chlorine concentration was lowered to 0.3 wt% after heat treatment at 1523 K for 10 hours. Under reduced pressure, however, 0.2 wt% residual chlorine was obtained after 8 hours at 1473 K.IntroductionIt is believed that aluminum recycling in the near future will become the main route of aluminum production [1]. Black dross (BD) that is produced during this process contains, among other things, high amount of salts like NaCl and KCl [2, 3]. Almost 800,000 tons of BD is annually land filled in United States and this number continues to grow with the increase in aluminum recycling [2]. The BD should be dumped in controlled land field and it is costly procedure [4, 5].The water-soluble compounds in BD react with water or environmental humidity and release chlorides into the water and/or generate toxic gases such as H2, CH4, NH3 and H2 S [6-8]. In the Europe, BD is considered as toxic waste and its disposal as landfill is forbidden [8, 9]. After salt removal, the BD is considered to be non-hazardous and can be buried under ground [10].On the other hand, BD do also contains many relatively valuable compounds that may be changed in to useful materials as a result of further treatment [11, 12]"

Jan 1, 2012

By John Hall

SOME months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter lie had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908; and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel.

Jan 9, 1919

By M. S. Badollet, W. C. Streib

"AbstractA commercial method .has been developed for controlling the texture of chrysotile asbestos fibers so that they may possess properties comparable with natural sem1-harsh fibers for use in wet •processes.The physical properties of the soft, silky and slimy fibers are partially altered by a flash-heating process which removes a portion of the molecular water.The heat-treated fibers show an improvement in filterability, an increase in bulk, absorption, and surface area and better electrical properties, such as volume resistivity.IntroductionCHRYSOTILE ASBESTOS fibers are found in nature having varying degrees of texture, referred to as soft, semi-harsh, and harsh. Fibers of each type of texture have inherent characteristics which directly affect their usefulness to industry. Visual differences are apparent under a microscope where it is seen that the soft-textured fibers have a silky, serpentine or wavy appearance, whereas the harsh-textured fibers are coarser and spicular. Semi-harsh fibers, of course, have properties intermediate between these extremes.Fankuchen and Schneider ( l) have shown by the use of low-angle X-ray scattering that the diameter of the harsh type of chrysotile fiber is somewhat greater than tha of the soft variety. Surface area measurements on various chrysotiles of different textures tend to confirm their findings. By nitrogen adsorption methods, it was found that the surface areas of soft types of chrysotile asbestos are approximately 23M2 / g whereas for the harsh types they are as low as 11M2/g."

Jan 1, 1955

By P. D. Merica

The remarkable phenomena exhibited by the aluminum alloy known as duralumin were discovered during the years 1903-1911 by A. Wilm1,2 and have been described by him and by others. 3 4 5 6 The unusual feature of this alloy is the fact, as was shown by Wilm, that it can be hardened quite appreciably by quenching from temperatures below its melting point followed by aging at ordinary temperatures, which consists merely f allowing the material to stand at these temperatures. The hardness is not produced by the quenching alone but increases during the period of aging, which may be from one to three days. Cohn3, 5 gives data showing the increase of hardness of duralumin during aging, after quenching in water from about 450° C. Upon annealing, the alloy so hardened by aging is softened exactly as is hardened steel. The composition of this alloy usually varies within the following limits: Copper, 3 to 4.5 per cent.; magnesium, 0.4 to 1.0 per cent.; manganese, 0 to 0.7 per cent.; aluminum, balance; iron (as impurities), 0.4 to 1 per cent.; silicon, 0.3 to 0.6 per cent. Its density is about 2.85. It is used only in the forged or rolled condition. This alloy has been produced for some years commercially and is in demand for the fabrication of parts for which both lightness and strength are required, such as for aircraft. Its tensile strength will average 50,000 to 60,000 lb. per. sq. in. (3515 to 4218, kg. per sq. cm.) after appropriate heat treatment, such as that described by Wilm.

Jan 6, 1919

ZAY JEFFRIES, Cleveland, Ohio (written discussion?).-The authors conclude that there is a certain average size of precipitated CuAl2 par-ticle which produces maximum strength and hardness in duralumin; that when the size of particle is smaller or larger than this particular size the hardness decreases. The writer agrees with this conclusion, because it seems to he directly indicated by the facts. Why does duralumin present this apparent discrepancy? Let us con-sider some physical aspects of the precipitation of CuAl2 from a saturated solution on cooling. When a molecule of CuAI3 is removed from the solvent, or matrix, and added to another group of CuAl2 molecules, as is known to occur on slow cooling, the forces of adhesion between the CuAl2 molecule and the solvent have been exceeded. Since a. change in tem-perature only is sufficient to cause precipitation, it must also be sufficient to cause the loss of adhesion bonds between the excess CuAl2 molecules and the solvent, or matrix. Lost adhesion bonds means loss of cohesion of the mass as a whole. When duralumin is cooled from 500° in a furnace, globules of CuAl2, large enough to be seen easily with a high-power microscope, are formed. There are, however, globules so small as to be hardly distinguishable, and others too small to be resolved are suggested by the non-uniformity of the surface appearance of the section. As the smallest globule of CuAl2 resolvable with a high-power microscope contains about 2,000,-000,000 molecules, it is evident that with rapid cooling submicroscopic particles of CuAl2 must be present in large numbers; in fact, after quench-

Jan 12, 1919

By George H. Gilman

THE campaign now being waged to improve the quality of the rock-drill bit is the natural outcome f the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc., on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack f continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination f the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved.

Jan 6, 1921

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By A. E. Nash

This title is somewhat of a misnomer, because it does not accurately describe the phase of heat generation and application coming within the scope of this discussion. This paper is concerned primarily with that particular phase of radiant-heat transfer sometimes erroneously referred to as "shielded" radiant heat, to differentiate it from the open radiant heat of either flame or settings, in which the actual source of the radiant heat is a small incandescent furnace composed of a highly conductive superrefractory, within whose walls the combustion of the fuel is completed. This small furnace is usually located directly in the furnace proper, and although its refractory walls do shield the heat-absorbing surfaces from contact with the gases of combustion, there is no interference with the radiant heat given off by the furnace itself. We do not believe it either necessary or advisable to shield or screen radiant heat when properly controlled and applied. We do believe it essential to prevent the excessively hot gases of combustion from coming in contact with those parts of the heat-absorbing structure that are already receiving heat at high rates by radiation. In connection with any process for the refining of oil with which we are familiar, we are convinced that it is most advantageous to transfer the maximum of the heat generated in the form of radiant heat, applied directly to the heat-absorbing surfaces without the interposition of any form of shield or screen to prevent or reduce the radiant-heat transfer. While the term radiant heat is broadly used to cover all heat energy transferred from one body to another by radiation, in contradistinction to heat given up by gases in direct contact with the heat-absorbing structure (convection) or transmitted simply by conduction, in furnace work it is perhaps more often limited to the heat rays given off either by

Jan 1, 1928

By L. A. Mekler

The recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to those produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack. The convection-type oil still is particularly suitable for the application of flue-gas recirculation. In an oil still, the heating of the oil is accomplished by applying to the tube surfaces a given quantity of heat of a certain predetermined quality, usually with the initial temperature of the gases not over 1500" F. as measured by thermocouples placed above the tube bank. To obtain the full benefit of the heating surface of the coil, the final temperature of the gases, after passing over the coil, is kept 200" to 300" higher than the temperature of the incoming oil. This final temperature varies from 500" F. for a topping still with only a slight or no

Jan 1, 1928

By John Primrose

Tube stills having demonstrated their usefulness for refining operations, the later developments in their design have been in the direction of improved thermal efficiency. The earlier designs operated with low furnace temperatures and large volumes of furnace gas because the fuel was burned with much excess air. It was quite possible to provide sufficient heating surface to lower the temperature of the flue gas to within 150" of the temperature of the inlet oil, or when inlet-oil tempera-tures were high to have the flue gas escape at 300" or 350" F. by using the heat remaining in the flue gas from the still to preheat the air supplied for combustion. But even so, the thermal efficiency was low because of the large quantity of air used for combustion. The large quantity of excess air was required to burn the fuel in the furnace at a temperature low enough to prevent overheating the furnace walls and overheating of the oil. Supplying heat to the tubes of the heating surface at a rate beyond the capabilities of the oil to absorb, except with a considerable difference between the temperature of the inside of the tube and oil passing through, would result in overheating the tubes and the oil in contact with them. For these reasons it was very necessary in the older types of tube stills to burn the fuel with large quantities of excess air, resulting in low thermal efficiency despite the low flue-gas temperature. Neglecting loss by radiation, the thermal efficiency could be improved only by burning the fuel with less excess air, but it was necessary to accomplish this without upsetting the furnace temperature conditions existing when large quantities of excess air were used. There are several methods of bringing this about, such as controlling the furnace temperature by returning a proportion of the flue gas to the furnace, or by exposing direct to the fire a heat-absorbing surface so located and proportioned that sufficient heat will be absorbed by radiation to prevent excessive furnace temperatures.

Jan 1, 1928

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By S. Q. Yang

Rotary radial jet improves greatly the pulsing velocity of airflow along each direction everywhere in the entry, intensifies transverse migration of air, eliminates effectively the local gas accumulation, and distributes methane concentration in airflow evenly and rapidly. According to the theoretical analysis of heat-transmission, mass-transmission and momentum-transmission, not only the similarity between heat-transmission and momentum-transmission, but also the similarity between mass-transmission and momentum-transmission exists in turbulent flow field, When the analogical equivalent ratio of heat transmission and mass transmission meets a certain criterion and remains a certain value, the temperature field can be used to simulate the methane concentration field. After hot airflow being released, thermograph instrument can be used to monitor the changing patterns of heat transmission and temperature distribution which simulates the changing patterns of methane transmission and methane distribution respectively. By analyzing these patterns and parameters of airflow field and methane distribution field during the process of local gas accumulation discharging by rotary radial jet, the dependability and validity of this discharging method are tested and verified.

Jan 1, 2004

By Y Omura

If dynamite is used in hot metal mines, it may be subject to decomposition, and the increase in nitroglycol vapour under the high temperatures causes bad headaches of workers. Also the explosives containing ammonium nitrate are very dangerous when mixed with sulfide ores at a high temperature!. Therefore we developed a heat-resistant water gel explosive which is safe to be handled at these hot metal mines.

Jan 1, 1983

By C. E. Corson

THE experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to have received less study and description from the standpoint of the metallographist than many others. The investigation here described was directed to the following points:-Steel containing about 0.50 per cent, of carbon : 1. The structure as related to the temperature, at the same rate of cooling; 3. The structure and physical properties as related to temperature at different rates of cooling; 3. The structure and physical properties as related to different finishing-temperatures and different rates of cooling; 4. The bearing of these observations upon the statement of Prof. Albert Sauveur.1

Sep 1, 1906