Search Documents

By Y. Hanada

Electrorefining at higher current density is desirable due to the increase in productivity attained without expanding the plant size. However, increasing the current density in common commercial practice causes problems such as anode passivation, dendritic deposition, cathode impurities and energy consumption. In general, agitation of the electrolyte is effective in suppressing these problems. To apply the agitation to commercial practice effectively, the method of agitation is important. One possible method is agitation by gas injection. In this study, fluid motion characteristics with gas injection between electrodes were investigated using a water model. Flow patterns were observed and fluid velocity was measured using a particle tracking method. It was found that the time-averaged velocity near the electrode walls was of the order of 0.1 m/s in the conditions. The flow was highly turbulent. The turbulent component of velocity was the same order as the time-averaged velocity. The mass transfer coefficient between the wall and fluid doubled when the effect of turbulent intensity was taken into account. The effects of gas injection on the electrolysis behaviour at high current density were discussed in terms of the mass transfer. It is suggested that gas injection could suppress the problems at high current density.

Jan 1, 2007

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By William A. Kennedy, Jonathan R. Stahl

This paper deals with the phenomenon of water held in a leach dump due to capillarity. Water is shown to be retained in the fine pores of the ore as well as in the interstices between the rock and soil particles. Upon drainage, Chino leach dump material shows two distinct capillary systems and a double capillary curve is often obtained. Both the igneous and the sedimentary rocks composing the leach material are shown to have appreciable porosity but little permeability. Fluid flow is, therefore, restricted to the interstices between the rock and soil particles. The irreducible water saturation for the aggregate is found to be 884 for the -48 mesh material and 235 for the448 mesh to one inch material. The composite sample of minus one inch dump material had an irreducible water saturation of 52 percent. The irreducible water saturation in the fine pores of the ore was found to be between 73 and 76 percent. Very coarse pores or channels between large rocks exhibit essentially zero capillary retained water. The presence of fine material in a dump can cause high water saturations to be retained and these saturations may be mistaken for perched water tables. Perched water tables can be drained but capillary water will be retained. Capillary pressure data can aid in distinguishing between perched water tables and capillary retained water.

Jan 1, 1974

By Quintiliani G, Giordano V

A research field of interest and a topical subject with the aim to reduce a considerable amount of coke in ironmaking is the injection into blast furnace stack of hot reducing gas combined with use of auxiliary fuels at tuyeres. In recent years evaluation studies and prelimirfary industrial experiments have been carried out on this subject in Europe and Japan. Even if these experiments seem to confirm the advantages theoretically expected, it appears as useful to cast more light on new problems concerning the improvements of this technique. In this report some aspects are analysed on fluid dynamics of blast furnace process with two gas flows: the main flow coming from the bosh and cross flow of the reducing gas injected in the lower shaft. A research on a blast furnace physical model was made with the aim to obtain information about the phenomena which occur in the full scale blast furnace. This work was carried out on cold models IN and tridimensional) in which the radial gas distribution was experimentally measured. A mathematical model based on gas diffusion was implemented aimed at simulating gas distribution inside the reactor taking into account the number of injection tuyeres. A good agreement between experimental and theoretical data allows for extending results to industrial practice in order to determine operating conditions assuring good performance of blast furnace with high amount of auxiliary fuels.

Jan 1, 1975

By B. Devulapalli

A mathematical model of the industrial hydrocyclone based on fluid dynamics is a better alternative to the currently existing empirical models. The swirling-flow velocities are determined by solving the Navier-Stokes equations with an appropriate turbulence model. The solution of the momentum-balance equations yields the flow field inside the hydrocyclone which determines the particle trajectories, and subsequently the classification curve. The essence of the model is that the physical dimensions of the hydrocyclone and the slurry characteristics can be incorporated, and the influence of these parameters reflects on the flow predictions. The predicted tangential and axial velocities in a 250-mm hydrocyclone are in good agreement with the laser-Doppler velocimetry measurements. Finally, the predicted classification curves show good agreement with experimental data measured on a KREBS Dl0B hydrocyclone.

Jan 1, 1993

By Ferenc Molnár, David H. Watkinson

Abstract - Cu-Ni-PGE footwall ore deposits were studied in the McCreedy East and Whistle mines along the North Range, and the Lindsley and Little Stobie mines along the South Range of the Sudbury Igneous Complex. The footwall ores in these localities differ from typical magmatic Fe-Ni-Cu- PGE deposits in the Sudbury mining camp: they have higher Cu/Ni ratios, higher PGE content, veinlike appearance and ubiquitous association of ore with hydrous silicates. Results of comparative fluid inclusion petrography and microthermometry of footwall ores indicate that high temperatures (300°C to 480°C) and heavy-metal rich saline (up to about 40 NaCl equivalent wt% salinity) fluids were associated with the formation of the PGE-rich footwall ores at moderately high pressures (around 2 kbars). However, several, possibly independent fluid circulation stages were also found at the different localities and there also are differences in detailed characteristics for ore-forming fluids especially comparing data from the North Range and the South Range. Thus, in addition to the high temperature and salinity of fluids, there are local variations in the nature of hydrothermal processes. These differences may be related to the diverse origin of fluids (magmatic, metamorphic, and formational brines) and their differing extents of interaction with the compositionally different footwall lithologies.

Jan 1, 2001

The Comstock Lode, a world-class precious metal vein district near Virginia City in western Nevada, U.S.A. (Fig. 1), produced 8.3 million ounces (0.28 X 106 kg) of gold and 193 million ounces (6.56 X 106 kg) of silver during the period 1859 to present (Bonham and Papke, 1969). More than 95% of production was from the Comstock fault, while the adjacent Silver City, Occidental and Flowery vein systems produced about $10 million (U.S.). Within the Comstock fault high-grade ore bodies, or bonanzas, were distributed over 2.3 miles (3.8 km) along strike and persisted to >3000 feet (>900 m) below the surface (Fig. 2). Bonanzas consisted of as much as 1.4 million tons (1.3 million tonnes) of ore grading up to 1.9 oz./ton (65 gm/ton) Au and 30 oz./ton (1020 gm/ton) Ag (Table 1). Some bonanzas occurred in the main Comstock fault plane while others, including the highest grade bonanzas, formed in hangingwall frac- tures. After 1880 most ore consisted of lower-grade vein material surrounding mined- out bonanzas and large volumes of mineralized vein and wall rock in the Comstock hanging- wall that were mined from open cuts. Deep mining was hindered by large quantities of hot water and bad ground which ultimately defined the limits of underground production. The widths and richness of Comstock bonanzas strongly influenced U.S. mining law, milling and underground mining methods, and securi- ties regulations that are in practice today. Within the district Mesozoic metasedimentary rocks, metavolcanic rocks, and granitic in- trusions are overlain by Miocene volcanic rocks (Thompson and White, 1964). Veins cut all lithologies. Miocene volcanic rocks and their K-Ar ages (Vikre, McKee and Silberman, 1987) include Santiago Canyon rhyolite (22

Jan 1, 1987

By D. H. Watkinson

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Part of the contact of the 4b orebody with the enclosing Murray granite is characterised by the presence of recrystallised and biotitic Sudbury Breccia; in places the contact is faulted and sheared. In other areas of the contact partly silicified granite contains disseminated chalcopyrite and quartz-chalcopyrite veins with other minor minerals. Both ore and veins contain platinum group minerals (PGM); predominant PGM are michenerite, kotulskite, merenskyite and sperrylite with Au, galena and Bi-tellurides. At some silicified-granite contacts Mn-rich garnets, some containing inclusions of PGM and quartz, are associated with biotite + epidote + stilpnomelane + quartz. PGM and Au also occur within Cl-rich biotite and ferropyrosmalite in massive sulphide and in siliceous ore. Quartz, chalcopyrite and feldspar in the contact rocks and in veins contain abundant, highly saline fluid inclusions. Studies showed that the fluids were trapped at intermediate temperatures. The 4b orebody is surrounded by a sheath of brecciated granite but is close to the Contact Sublayer. During and after emplacement of sulphide magma, saline formational fluid that was resident in the breccia interacted with hot massive sulphides in and near the Sublayer and remobilised Cu, Au and PGE. This fluid reacted with cooler rocks and ore in footwall fractures, enriching the 4b protore and producing the adjacent Cu- and PGE-enriched quartz veins. Exploration for Cu and PGE enrichment in footwall rocks of the Sudbury South Range is warranted not only in zones of magmatic ore in the Contact Sublayer but also in fractures and permeable units within Sudbury Breccia

Jun 16, 1905

Fluidised Bed Combustion technology has expanded since the first fluidised bed boiler steamed in 1974 with 58 companies currently supplying units. In Australia the market has been in small boilers and the goal of a limited attendance coal fired boiler has been achieved. On the world scene, the major incentive for development has been emission control with sulphur capture and low NOX. The potential of significant reduction in plant size is encouraging development of pressurised fluidised bed combustion.

Jan 1, 1987

By Andre Krzysik

"Fluidized bed technology has been used in the industry for almost 100 years. To fully understand the process hundreds if not thousands of researchers were and are involved in finding the way to predict the behavior of the solids when subjected to the flow of media through them and the conditions of the solids in the fluidized state. The difficulties in predicting the behavior of solids in the fluidized state stem from the complexity and abnormality of the parameters related to the solid particles. Theoretical calculations can in some degree account for some of them. Particle size distribution, their shape, density, moisture content and physical and chemical reaction that may exist in the fluidized bed reactor play an extremely important role and influence the behavior of the fluidized bed. This paper focuses on the practical examples of the fluid bed equipment and the use of different conditions to process various products.IntroductionEach process application has its own unique requirements and the designers of the equipment must take into consideration specific process requirements, specific properties of the material to be processed (both physical and chemical), and physical and chemical reactions/changes that are taking place in the reactor (heat and mass exchange, chemical reactions, isomorphic change etc.). Each individual piece of equipment must also satisfy specific requirements/ preferences of the client that will operate and maintain the equipment. Those often represent greater challenges than the process on its own, and are equally important to the satisfactory operation of the plant. That includes aspects like location of the equipment, environmental effects, and expected life of the equipment, process control, access, maintenance, and many others.Over the period of time a great deal of research, both theoretical and practical have been carried out and the results of that work are available for equipment designers. For the simple applications that information is usually sufficient and the selection of a suitable solution is relatively simple. In many instances, the available information is not sufficient, and often specialized test work needs to be conducted to obtain additional data. In many cases a pilot installation is built in which the required process is tested. Only then the commercial equipment is designed. The following deal with specific installations that were designed to satisfy specific requirements. In some instances, additional problems were discovered during the commissioning of the equipment that required on site modification. The continuous monitoring of the equipment that was supplied to the various clients allowed us to further develop and improve our designs."

Jan 1, 2014

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By Ligang Zhang, Wen Chen, Xinghua Liu, Jialin Li, Xiaoyin Liu, Zhenhong Liao

A research-scale fluidization and magnetization roasting device was developed to evaluate a processing option that might offset the complexity and high cost of the conventional magnetization roasting process on siderite. In this study, the operating parameters of the fluidization and magnetization roasting device for siderite were evaluated through cold-flow tests and magnetization roasting tests. The reaction mechanism functions of the fluidized roasting process are revealed with kinetic studies.

Jan 1, 2015

By Y. Zhang, F. Zhu, Y. Zhao, L. Dong, Y. Li

In order to obtain a more suitable separation medium for fine coal, in this paper a pulsed fluidised bed was used to measure the pressure fluctuation, density characteristics, bubble diameter and rising velocity of Geldart A and B particles in the bed by controlling the pulsation frequency and gas velocity, in order to study the fluidisation effect and two-phase distribution of the bed. The results indicated that with the increase of pulsation frequency, the breakthrough point on the fluidisation characteristic curve caused by particle adhesion disappeared, and there was an optimal frequency, which made the minimum fluidisation velocity of particles reach the minimum. In addition, the bubble rising velocity was also simulated. The relationship between them was established using a model, and the error was within 5%. This provides an effective way to predict the bubble velocity, study the distribution of bubble phase, and improve the stability of bed density. Keywords：Frequency, flow velocity, pressure fluctuation, bed density, bubble

Jan 1, 2020

By S. Moodley

In the chloride process for Ti02 pigment production, various titania feedstocks (i.e. rutile, synthetic rutile, slag, and upgraded titania slag (UGS)) are chlorinated in a fluidized bed reactor with petroleum coke at temperatures between 1000°C and 1100°C to yield gaseous metal chlorides. Although feedstock preference is largely based on Ti02 content, feedstock physical properties (i.e. density, sphericity, size distribution, and porosity) differ; these differences will affect fluidization behaviour and can inadvertently affect conversion efficiency. For example, a high carryover from the reactor reduces particle residence time and decreases conversion rates. Owing to dwindling rutile reserves in the world, most chloride producers are forced to feed blends of feedstocks to their chlori¬nators; and so it becomes important to understand whether blends have an effect on the hydrodynamic properties of the bed. This paper describes the physical characterization of different feeds and the determination of the elutriation constants for slag, rutile, synthetic rutile, and a blend (i.e. 50 wt% rutile, 50 wt% slag). A common feature of the tests was that particles finer than 75 Km tended more than any other size to be elutriated. The tested rutile, classified as a Geldart Group B material, had the lowest carryover, whereas the slags had the highest. Interestingly, the elutriation constant (ki) of the blend is lower than those of either of its individual components.

Jan 1, 2012

By S. Moodley

In the chloride process for TiO2 pigment production, various titania feedstocks (i.e. rutile, synthetic rutile, slag, and upgraded titania slag (UGS)) are chlorinated in a fluidized bed reactor with petroleum coke at temperatures between 1000°C and 1100ºC to yield gaseous metal chlorides. Although feedstock preference is largely based on TiO2 content, feedstock physical properties (i.e. density, sphericity, size distribution, and porosity) differ; these differences will affect fluidization behaviour and can inadvertently affect conversion efficiency. For example, a high carryover from the reactor reduces particle residence time and decreases conversion rates. Owing to dwindling rutile reserves in the world, most chloride producers are forced to feed blends of feedstocks to their chlorinators; and so it becomes important to understand whether blends have an effect on the hydrodynamic properties of the bed. This paper describes the physical characterization of different feeds and the determination of the elutriation constants for slag, rutile, synthetic rutile, and a blend (i.e. 50 wt% rutile, 50 wt% slag).A common feature of the tests was that particles finer than 75 µm tended more than any other size to be elutriated. The tested rutile, classified as a Geldart Group B material, had the lowest carryover, whereas the slags had the highest. Interestingly, the elutriation constant ([ki]) of the blend is lower than those of either of its individual components.

Jan 1, 2012

By Z. Luo, W. Chen, Y. Zhao, Y. Fu, L. Dong

The gas-solid dense-phase fluidised bed includes a complex multiphase fluid-particle system; different complex exchanges significantly affect the stability of the fluidised bed. To elucidate the characteristics of fluidisation in a gas-solid dense-phase fluidised bed, this study used experimental performance tests to obtain the static density characteristics, and the attachment and flow characteristic of the dense medium. The results indicate that the bulk density of the dense medium increases first and then decreases with the increase of particle size. The airflow rate difference is used to quantify the wall attachment characteristics of dense medium and the average pressure gradient in the axial direction of the bed is approximately 20 Pa/mm under the fluidisation results. At the same settlement location, with the decrease of fluidisation number, the settlement velocity of large and small particles becomes slower, the boundaries of settlement displacement and location probability are gradually disrupted, and the falling velocity of particles with a radius of 20 mm is faster than that of materials with a radius of 15 mm. This work also established a theoretical basis for regulating the stability and separation characteristics of gas-solid dense-phase fluidised bed. Keywords: Fluidised bed, different size particles, fluidisation characteristics, flotation bubbles, settling motion

Jan 1, 2020

By Vernon F. Swanson

The expansion of a fluidized bed of carbon depends on fluid velocity, fluid temperature (viscosity) and particle size of the carbon. This paper presents a mathematical model which can be used to calculate the necessary fluid velocity. It will allow the design of sufficient freeboard in the column to accommodate expected operating conditions. Although this paper is keyed towards the use of activated carbon in precious metals adsorbtion from water solutions, the model is.valid with any fluid. Additionally, the method of calculating the required suspension velocity in CIL or CIP pulps is described.

Jan 1, 1992

By Joerg Hammerschmidt, Marcus Runkel, Andreas Wirtz, Kent Pope

"Fluidized bed reactor systems in the minerals industry have been progressively developed and widely implemented over a period of more than sixty years for a multitude of process applications. Their versatility is manifested in calcining, roasting and combustion treatment of minerals including solid fuels. Experiences from metallurgical processes have expanded to new applications in the oil shale processing, biomass combustion and renewable energy sector. This paper focuses on the most important aspects of fluidized bed technology for a variety of Outotec processes. Energy recovery is a major topic for all applications and will be addressed, as well as environmental aspects, particularly regarding the off-gas treatment. Outotec is one of the pioneers of roasting and the fluidized bed process including gas cleaning and sulphuric acid production where applicable. Process development is strongly supported by significant investment in R&D, thus enabling process adaptation and scale-up to meet specific customer/market requirements.Introduction to Fluidized Bed TechnologyThe early days of fluidized bed technology were characterized by the use of bubbling fluidized bed reactors (BFB). This technology was popular for roasting zinc and copper ores. The introduction of circulating fluidized bed technology led to increased plant capacities and improved process control for the traditional processes. Furthermore, the technology has been applied in many other industries, including the renewable energy industry, which will be part of this design and process comparison. The paper starts out with the fundamentals on particle fluidization as the main common design parameter, leading to the importance of heat recovery and offgas treatment.In fluidized reactor systems, the particle concentrations can reach several hundred kilograms per cubic meter of fluidization gas. This high solid concentration leads to large surface areas and enables direct contact of gas molecules with particle surface molecules. Excellent conditions for enhanced heat and mass transfer thus provide nearly ""ideal"" heat exchange conditions and better reaction kinetics. The bubbling bed exhibits a better heat transfer coefficient within the bed in comparison to the circulating fluidized bed (CFB). The different conditions of gas velocities and solid concentrations allowing the classification of fluidization reaction regimes are shown in the Reh diagram in Figure 1."

Jan 1, 2014

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By William J. McCloy, Robert L. Gamble

A coal-fired fluidized bed steam generator rated at 12.6 kg/s has demonstrated the industrial and institutional application of fluidized bed combustion by burning high sulfur coal in an environmentally acceptable manner within a populated area. Designed to provide steam for heating and cooling, the unit was placed into service at Georgetown University in Washington, DC, and has already logged 5275 hours.* The unit has consistently operated well within Washington's strict regulations governing emissions of sulfur dioxide (SO2), nitrogen oxides (NOx), and particulates. The Georgetown program, cofunded by the university and the US Department of Energy, has shown that fluidized bed combustion is a promising way to realize the full potential of coal, the nation's most abundant energy resource. In a fluidized bed steam generator, a layer of granular limestone is placed on top of a grid designed to prevent particles from falling through. Air is passed upward through the bed with sufficient force to lift and float the particles. At this point the bed material resembles a boiling liquid. Crushed coal is then introduced into the bed and ignited. When high sulfur coal is burned, limestone absorbs the SO2 produced. The operating temperature of a fluidized bed steam generator is relatively low (approximately 871°C). As a result, NO, formation is minimal. Another potential problem encountered in burning coal is fly ash, a form of particulate. A feature of the fluidized bed design, developed by Foster Wheeler Energy Corp., is a fly ash reinjection system. Fly ash is reintroduced into the bed where it is burned again, thereby enhancing fuel efficiency. Nearly all remaining fly ash is captured by a baghouse dust collector. At Georgetown, the fluidized bed steam generator and all auxiliary equipment are enclosed in a structure aesthetically compatible with the surrounding university complex. The steam generator has two separate beds that can be fired independently, and operation to date has been with one and two beds in service, based on steam load demand. During several operating periods, when the fluidized bed unit was the only boiler in service, it supplied all the steam required by the 18.5 hm2 of buildings on campus. Initially fired with low sulfur coal, the unit was quickly switched over to higher sulfur fuel which will be used most of the time.

Jan 3, 1981