Search Documents

By Panshi Xie, Yan Chen, Shaogang Wu, Yang Hang

In order to realize the intelligent mining of coal seam with large dip Angle, this paper adopts the methods of large proportion variable Angle loading threedimensional physical simulation experiment, numerical simulation and field measurement with digital twin technology. The hydraulic support with large dip Angle and large mining height is used as the prototype to design the physical entity model of 1:5 hydraulic support, combined with modeling and graphics rendering technology. Angle, displacement and load sensors were selected and placed to realize the data channel between the lower machine and the upper computer of the digital twin system, so that the position and load data of the physical entity model and the twin model of the laboratory hydraulic support could be shared in real time. Moreover, the multi-dimensional dynamic and static load transfer law and the position evolution characteristics of the support and surrounding rock under different inclination angles were analyzed. The results show that: with the increase of the Angle of the working face, first, the initial support force required by the support decreases, and the damage degree of the roof increases; When the roof is soft, the lifting operation can avoid the instability of the support to a certain extent. Second, under the action of positive pressure, the load of the top beam under different angles is balanced; Under the backpushing action, the load in the upper inclined area of the shield beam increases gradually, while the load in the lower inclined area decreases gradually. Under the lateral push, the load changes periodically, and the load in each cycle is increased compared with that in the previous cycle. Third, the numerical simulation analysis shows that the load on the lower bracket is less than that on the upper bracket, and the load on the bottom of all the columns is greater than that on the middle and upper brackets. In order to reduce the impact of the columns on the bottom plate or the base, it is necessary to improve the anti-subsidence ability of the base. Finally, according to the research results, the improvement and optimization measures of the support are put forward, and the field test shows that these measures effectively solve the problems of sinking, sliding and tipping of the support in the working face with large inclination Angle, and obtain good application results.

Feb 1, 2024

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By Jing Zhang, Qing Xiao, Xulong Liu, Qiuju Li

"Pickling sludge generated from stainless steel production process contains large quantity of Cr, Ni, and Fe. The disposal of and fill sludge directly not only leads to the heavy metal dissolves in the soil and underwater, but also loss value metals. However, the major mineral phases of value metal are hydroxides and there are lots of calcium fluoride and water in the sludge. So the pickling sludge has to be pretreated before reduction-magnetic separation. The TG analysis, reduction reaction and magnetic separation were all used to study the pickling sludge. The result indicated that up to 900°C the total weight loss of pickling sludge was 22.32%. The mass contents of Fe, Cr and Ni in the tailings (non-magnetic) were 4.27%, 0.067% and 0.041% respectively.IntroductionSince 21st century, the stainless steel production in the world has been continuously increasing because of its excellent performance [1]. However, high stainless steel production means a high pickling sludge production. For example, in a stainless steel plant with waste water quantity of 100m3 /h, the production of pickling sludge will exceed 15 Kt/a. Pickling is essential for generating of a homogeneous and corrosion-resistant surface during stainless steel production subsequent process. Pickling of stainless steels is predominantly carried out with an aggressive solution, sulfuric acid H2S04 or composed of nitric acid HN03 and hydrofluoric acid HF [2]. During the pickling process, the pickling acids are recovered through ion exchange and metal ions such as Fe3+, Cr3+ and Ni2+ get into the acids forming the pickling waste water [3]. Then, the pickling waste water is precipitated with lime, forming pickling hydroxide sludge. It is not feasible to recycle or treat the pickling sludge using conventional methods, because the sludge has high contents of calcium fluoride and water but low contents of iron, chromium and nickel. However, it would also pose a potential environmental problem if deposited outdoors over a long term because it contains heavy metals such as Cr and Ni. At present, solidification/stabilization (S/"

Jan 1, 2014

By Lijun Lu, Honghui Fang

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 ~ 2% is optimal, where flexural strength is reduced by 10% ~ 23% and compressive strength reduced by 5.7% ~ 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 ~ 2%, the flexural strength is increased by 5 ~ 7% and the compressive strength is reduced by 1 ~ 2%. The results show that the formula two is better.

Jan 1, 2015

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Lithium-ion batteries can go through a thermal runaway under different abuse conditions including thermal abuse, mechanical abuse, and electrical abuse, leading to a fire or explosion. The NIOSH Mining program is conducting research to prevent and respond to lithium-ion battery fires for battery electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, class D powder, and water mist for lithium iron phosphate battery pack fires. The effects of activation time and release time of the water mist system on the suppression of lithium-ion battery fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Feb 17, 2024

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion (Li-ion) battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Li-ion batteries can go through a thermal runaway under different abuse conditions, including thermal, mechanical and electrical abuse, leading to a fire or explosion. The National Institute for Occupational Safety and Health (NIOSH) mining program is conducting research to prevent and respond to lithium-ion battery fires in battery-electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, Class D extinguishing powder and water mist for lithium-iron-phosphate (LFP) battery pack fires. The effects of activation time and release time of the water-mist system on the suppression of the LFP battery (a type of Li-ion battery) fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Aug 1, 2024

By Takeru Fukaya, Tsutomu Namikawa

"The bending tensile stress occurs in the ground improvements when external forces are applied to the column and wall shaped ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements rationally.Three points bending tests are conducted to investigate the bending tensile properties of cement-treated soils in this study. Cement-treated soils mixed in a laboratory are used in the bending tests. The test specimens are prepared with the several mixing properties to study the relationship between the tensile properties and unconfined compressive strength qu. Bending tensile strength Tfb and fracture energy Gf of the cement-treated soils are evaluated from the load-deflection curves obtained from the bending tests. The experimental results indicate that Tfb and Gf are approximately proportional to qu.INTRODUCTIONThe ground improvement by deep mixing has been widely used for structure foundations, retaining walls and liquefaction mitigations. Recently column and wall shaped ground improvements by deep mixing method have been applied for economical reason. When external forces are applied to the column and wall shaped ground improvements, the bending tensile stress occurs in the ground improvements. Therefore, in the design of the column and wall shaped ground improvements, the tensile properties of the cement-treated soils become a predominant factor when the external forces induce bending moments. Then the tensile properties are required to design the ground improvements appropriately.Namikawa et al. (2007) conducted the finite element analysis to investigate the dynamic behavior of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, an improved ground consisting of several grids in a line was chosen to study the basic behavior of the lattice-shaped improved ground. Fig. 1 shows a example of calculated tensile failure zones in the improved soil during the earthquake. Half of one section of the improved soil consisting of two grids in a line for the 8 m × 8 m grid was modeled in the case. In Fig. 1, the failure occurs at the bottom and upper corners of the improved soil grid. The analysis result indicates that the constitutive model which can appropriately evaluate tensile failure behavior of cement-treated soils is required to evaluate the performance of the lattice-shaped improved ground for liquefaction mitigation. In the analysis, the elasto-plastic model developed by Namikawa and Mihira (2007) was adopted for the cement-treated soil behavior. The elasto-plastic model can suitably describe the tensile failure behavior of cement-treated soils. In the elasto-plastic model, tensile fracture energy is adopted to determine a tensile softening relationship because it is difficult to directly measure the stress-strain relationship after the peak stress state in direct tension tests. However there is little experimental study on the tensile fracture energy of cement-treated soils."

Jan 1, 2015

By Chunfeng Zhao, Chong Bao, Cheng Zhao, Jiashen Tian, Matsuda Hiroshi

"Based on digital image correlation (DIC) method and self-developed code, the global strain field changing and failure properties of rock-like materials with pre-existing double flaws are experimentally studied under uniaxial compression. By theoretical analysis with linear elastic fracture mechanics (LEFM), the strain approach proves to be practicable to investigate cracking process. Thus, two types of process zone are defined to discuss the specimen’s coalescence evolution at different loading stages. Crack initiation, propagation, and coalescence is a process of zone development and nucleation. DIC strain field results are studied on a meso-level using a strain approach. In the shear coalescence mode, the SPZ (shear process zone) in a bridge area coalesces with each other, while the TPZ (tensile process zone) grows independently. In general, the paper tries to establish the link between microscopic mechanical mechanisms and macroscopic mechanical responses in flawed rock. Further research should be done to study the cracking process and its effect on rock strength in detail by the DIC method.INTRODUCTIONNatural rock contains discontinuities including pores, fractures, inclusions or other defects. The existence of these discontinuities in the rock can decrease the strength and stiffness of the rock and they are a source of initiation of new discontinuities which may in turn propagate and link with other cracks and further decrease the strength and the stiffness of the rock (Sagong & Bobet, 2002). Lots of theoretical, experimental and numerical researches have been done in studying crack initiation, propagation and coalescence in rocks (Hoek & Bieniawski, 1965; Kranz, 1983; Reyes & Einstein, 1991; Park & Bobet, 2009; Gonçalves & Einstein, 2013). But when it comes to multiple pre-flaws, the issue that how the preexisting flaws affect each other becomes complicated and uncertain. The stress field around the tips of flaw can either enhance the impact of single flaw or weaken it. According to the observations have been done before, it is found that the way and function in which these cracks propagate and coalescence depends on the geometric arrangements (Bobet, 1997; Bobet & Einstein, 1998; Wong & Chau, 2001)."

Jan 1, 2015

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By Yingtao Zhang, Shaofeng Du, Yiming Rong, Wenjun Zhao, Gang Wang

"20Cr2Ni4A steel is a kind of high quality steel mainly used for manufacturing high-duty gears in the world. The high-duty gear with good performance must have wear and fatigue resistance properties. In order to get the good properties, the high-duty gear needs a high hardness gear surface and a good hardness gradient along the depth direction. In this paper, the samples were designed and a vacuum carbonitriding process was put forward to improve the surface hardness of parts for 20Cr2Ni4A. The process contained carbonitriding, quenching, cryogenics, and tempering process. The surface hardness and hardness gradient of carbonitrided samples were measured and the good microstructure was gained. The surface hardness is 67.SHRC and the case depth is 1.2mm.IntroductionSteels are widely used in industry, but the fatigue strength and the wear resistance of steel is much low. So the heat treatment process is put forward to improve the mechanical properties of steel. It can be improved by high-energy heat treatment methods for medium-carbon and highcarbon steel. Those methods will not alter the chemistry of the base metal [ 1].For low-carbon steels, carburizing and quenching should be used to improve the steels' mechanical properties, especially the surface properties. Compared with the carburizing, carbonitriding has more advantages, such as a short production cycle, low temperature and small deformation of parts. Carbonitriding is a modified form of gas carburizing, rather than a form of nitriding. The modification consists of introducing ammonia into the gas carburizing atmosphere to add nitrogen to the carburized case as it is being produced. Nascent nitrogen forms at the work surface by the dissociation of ammonia in the furnace atmosphere; the nitrogen diffuses into the steel simultaneously with carbon. Typically, carbonitriding is carried out at a lower temperature and for a shorter time than is gas carburizing, producing a shallower case than is usual in production carburizing [2]. As a material surface strengthening technology, carbonitriding has been widely used in the production [3]. And vacuum carbonitriding process is better than carbonitriding, because the vacuum carbonitriding temperature can be higher than carbonitriding without surface oxidation."

Jan 1, 2014

By B Zhao

Gas and coal dust, as potential harmful elements (PHEs) produced during mining, are considered two serious threats to the safe mining and the health of miners because of its explosive and pathogenic properties. To solve this problem, compound reagents enhanced water spraying technology was used to control the gas and coal dust in excavation working face in this study, and spray testing platform and wind tunnel were used to investigated the suppression effect for gas and coal dust. In addition, sink test, and agglomeration experiments were also used to analyse its suppression mechanism. Testing results show that the dust reduction efficiencies of compound reagents enhanced water spraying technology for four different particle sizes were 80 per cent, 91.43 per cent, 94.74 per cent and 94.46 per cent, and improved by 14 per cent, 10.86 per cent, 8.42 per cent and 4.25 per cent compared to water spraying. Moreover, the gas suppression efficiency also can be increased more than 20 per cent. Sink test, and agglomeration experiments results show that compound reagent improves the spreading efficiency of the liquid on the surface of the coal by changing its wettability, and this process can not only slow down the desorption rate of gas by forming a water-sealing effect in the coal surface indicated, but also promote the agglomeration of fine-grained coal dust.

Oct 12, 2022

By X Zhang, Z Guang, R Lin

To improve the existing process of a large-scale scheelite concentrator in Jiangxi Province, this paper presents an advanced process æselective flotation of copper and flotation desulfurisation û rougher flotation of scheelite û heating-stirring and cleaning of rougher concentrate at normal temperature without reagent removalÆ. The test work was conducted on an ore sample containing 0.75 per cent tungsten (WO3), and the following technical indices were obtained: 1.03 per cent of the scheelite concentrate yield, 65.37 per cent of the concentrate grade and 86.31 per cent of WO3 recovery, indicating that the study achieved the objective of improving the tungsten recovery. The technical key of this process is to employ combined regulators and direct flotation of the slurry after being heated, which not only assured the technical indicators of beneficiation but also simplified the process.

Jan 1, 2008

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By Xiaojian Zuo, Yihua Han, Qingguo Xue, Jingsong Wang, Lintao Wang, Rongzong Lan

"Using the facility of reduction experiment, the low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace (OBF) were studied. Through analyzing the results, the difference of pulverization and reduction behavior of sinter in OBF and conventional blast furnace (BF) were discussed. Furthermore, the effect laws of reduction temperature and the content of CO and H2 on reduction behavior of sinter were studied. Also the controlling step of iron oxide reduction was discussed. Compared with BF, the low temperature reduction pulverization of sinter became serious at 773 K; reduction rate became faster at 1173 K; reduction time became less and final reduction degree was increased in OBF. With increasing of H2 and CO contents, the reduction of sinter was promoted. The reduction process was controlled by interface chemical reaction at the earlier stage and by interface chemical reaction and internal diffusion at the final stage.IntroductionThe new ironmaking technology of Oxygen Blast Furnace (OBF) is most likely to be used in large-scale application process. The concept relies on the removal of the CO2 contained in the top gas of the blast furnace. Therefore the useful components, i.e. CO+H2, can be recycled back into the furnace and reused as reducing agents. In addition, injecting oxygen (O2) into the furnace instead of preheated air, removes unwanted nitrogen (N2) from the gas. Under the pressure of CO2 emissions in iron and steel making, the growing international shortage of coking coal resources and the rising price of coke, OBF has attracted attentions of both domestic and foreign researchers, because it has so many advantages such as high productivity, high PCI rate, low coke rate, high gas reducing capability and high top gas calorific value, etc [1-7]. As a result of recycling most of the top gas after CO2 removal and injecting oxygen into the furnace, the reduction capacity of blast furnace gas will be increased, so the metallurgical behavior of OBF's iron burden is different from traditional blast furnace. Therefore, it is one of the keys to develop this technology, which studies the metallurgical behavior of sinter in OBF. The purpose of this paper is to study the low temperature reduction pulverization and reduction behavior of sinter at the atmosphere of OBF, which includes the difference of low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace and conventional Blast Furnace (BF). It will provide theoretical basis for the development of OBF."

Jan 1, 2012

By K. Fagerlund

In this work, the rate of dissolution, melting behaviour and phase separation of silica flux with molten slag and matte were investigated. Mutual dissolution between high-grade matte and silica was chemically determined. Silica dissolution rates ,in various iron silicate slags was determined using the rotating rod method. The reaction and separation phenomena of slightly oxidised chalcopyrite samples and cuprous sulphide-magnetite mixtures with silica sand were examined all about 1350°C. The samples were water quenched, and polished specimens were studied and analysed using a light optical microscope ,and a scanning electron microscope with energy dispersive spectrometer. The silica dissolution rate in slag was found to increase with decreasing silica content and increasing ferric iron content. The reaction rate of silica sand' with matte was found to increase with increasing oxidation degree and magnetite content of matte:

Jan 1, 1998

The deformation, failure, and filling characteristics of a caving roof in the initial and normal mining stages of a pitching oblique longwall mining area are analyzed using large-scale threedimensional physical-similitude experiments and numerical calculations to study the characteristics of roof fracture and migration in a steeply dipping seam. The results show that the roof fracture development has evident sequential and spatial characteristics. Among them, immediate roof breaking in different parts of the mining area shows difference in time and space. The failure sequence of the immediate roof in different areas changes with the mining; unique regional stability evolution characteristics are observed in the suspended immediate roof simultaneously, resulting in its significant regional stability on the goaf filling.

Jan 7, 2020

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By Jun Deng

The aim of this paper is to study the scientificity and reliability of three coal gas indices used to predict coal fire disasters, namely Graham?s ratio, CO/CO2 ratio, Litton ratio and their different characteristics and service conditions. Data from a programmed temperature experiment were applied to check their veracity and accuracy. Each index performed well in detecting the level of a fire. We conclude that it is better to redefine the definition through experimentation before applying a given index. Integrated analysis of the results can provide reliable reference data for predicting spontaneous combustion of coal.

Aug 1, 2013

By Sun Ying, Zhang Jing, Li Qiu-ju, Wang Yan-ze

Copper smelter slag was leached using sulphuric acid solutions under atmospheric conditions. Base on the composition and phase of copper slag, the effect of the concentration of sulfuric acid and leaching temperature to the leaching growth rate of Fe, Cu, Co and Ni in the copper slag were investigated in this paper. Simultaneously, the influence of sulfuric acid concentration, leaching time, leaching temperature and the amount of sulfuric acid (solid-liquid ratio) to the leaching rate of these metal elements were researched. Experimental results showed that: with the increasing temperature, the dissolution rates of the metals elements increased first and then decreased. Due to the influence of silica gel which was obtained in beginning of leaching, the higher the concentration of sulfuric acid is not conducive to dissolution of the valuable metal elements. The dissolution degree of Fe, Cu, Co and Ni were 92.83% 96.76% 93.62% and 63.41% respectively.

Jan 1, 2016

By I. A. Podkamennyi, O. E. Kovalchuk, G. P. Dvoychenkova

"Using the methods of electron microscopy and IR spectroscopy, mineral components in the run-of-mine kimberlites and on the surface of diamonds were identified. The mechanism and sequence of mineral formation on the surface of diamond crystals were established. Systematization and classification thereof were undertaken for the first time ever.INTRODUCTION The high content of diamonds sized -5 mm in the kimberlite ores of Western Yakutia determines their processing depth in the size class 0.5 mm and finer [1, 2]. These diamonds are recovered by grease and froth separation based on the natural hydrophobic properties of the crystals. When refractory altered kimberlite ores are fed into the industrial process, the performance of grease and froth separation of the diamond ore greatly deteriorates. [4, 10, 15, 17]. Altered kimberlites are known to contain up to 90% of secondary minerals. This reduces by up to 40% the recovery of diamonds by grease and froth separation. [6].Diamond crystals from the grease and froth separation tailings were investigated. On the surface of the examined diamonds, hydrophilic mineral formations were identified, responsible for reduced recovery by physicochemical separation methods [3, 12, 18]. The aim of this study was to identify and describe the relationship between the composition of kimberlite ores and mineral formations on the surface of diamond crystals in order to systematize, classify, and then develop methods of removal in grease and froth separation processes. MATERIALS Following materials were examined in this study: - kimberlites of various material composition, - resulting slimes, - diamond crystals from kimberlite ore processing products."

Jan 1, 2018