Search Documents

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

The influence of joint orientation and joint persistence, on the mechanical behaviour of jointed rock masses under uniaxial compression, has been studied systematically. The joint inclination angle ß was varied from 0° to 90° with an increment of 15°. The joint continuity factor k was taken as 0.2, 0.4, 0.6 and 0.8. The peak strength, Young’s modulus, the complete axial stress-axial strain curves, the cracking process and the characteristic of the fragments, were investigated. It was found that the anisotropic response of the jointed specimens was governed by the micro-mechanism, such as crack initiation, propagation and coalescence, crack opening or closing, and frictional slip of cracks or joints. With the increase of joint continuity factor, the axial stress-axial strain curves change from single-peak to multipeak, the peak strength and Young’s modulus decrease. The specimens with medium joint inclination angle (30°,45° and 60°) has lower energy dissipation and strength due to stepped or shear failure, while specimens with small and large joint inclination angle (0°, 15°, 75° and 90°) has higher energy dissipation and strength due to axial cleavage or crushing failure.

Jan 1, 2015

By J. C. Glandus, N. Tessier-Doyen, M. Huger

The Young's modulus of bi-phased model materials (vitreous matrix containing spherical alumina inclusions) have been determined by two complementary approaches: experimental and analytical. If the matrix and inclusions exhibit close coefficients of thermal expansion, the experimental results lie in the vicinity of the lower bound of the Hashin & Shtrikman's model. If there is a dilatometric disagreement between the components, untypical behaviors, similar to those obtained for a family of industrial refractory materials, were observed when the temperature varies.

Jan 1, 2004

By Th. Probst, M. Reuter, H. Orbon, U. Boin, J. Vonken, P. Vonk

Although secondary aluminum industry is well established in the world, the recycling process still requires further development to adequately control the process for a higher aluminum yield and a better product quality. In the present paper, recyclabilities of different aluminum scraps have been experimentally studied. Four types of commercial scraps were characterized and melted at 800 - 900 °C to recover 'aluminum metal with the protection salt flux of NaCl-KCl-Na3AlF6 under nitrogen atmosphere. According to the results, the difficulty of recycling aluminum scrap depends on the cleanness and the ratio of surface area to body volume. More non-metallic contaminates and higher ratio of surface area to body volume usually led to a lower metal yield. Usually cast ingots gave better results than rolling mill cuttings under similar conditions. Bottle caps can be recycled more easily than the margarine foil. The effect of temperature was not as significant as the composition of salt flux. The addition of cryolite was essential for a better metal recovery, especially for the scraps with higher surface area. Recycling

Jan 1, 2000

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The paper evaluates the attenuation behavior of acoustic emission (AE) signals in four different materials used in marine environments. The study aims to identify materials with the highest and lowest AE signal attenuation, providing insights into wave propagation and structural monitoring in deep-sea mining applications.

Dec 1, 2023

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By J. Y. Liu

In Comparison to the application of HPGR (high-pressure grinding rolls) in the cement industry and in iron ore processing, the introduction of this energy-efficient comminution technology to processing of nonferrous base-metal ores has progressed slowly as yet. In the field of minerals industry, challenges lies not only in the large variety of the feed material with respect to particle size, density, hardness, moisture and mineralogy of the material but also in complexity of the processing flowsheet, which need to be addressed from case to case based on result of HPGR comminution test work. Whereas conventional comminution test with HPGR in lab-scale or pilot scale needs quite a large amount of feed material, a compressive stressing test of particle-bed in piston-die device provides an effective way to study interparticle breakage behavior of ore material with much less feed. In the present study the effects of interparticle breakage on comminution of a copper ore has been investigated by compressive stressing of particle bed in a piston-die device. The feeds to the particle-bed stressing tests were four narrow size fractions in the size range of 0.3~3.35 mm and a broad size fraction of 0/3.35 mm. The pressures applied were in the range between 30 and 180 MPa. The results showed that the specific energy consumption increases linearly with the pressure; the product fineness increases also with the pressure, but the magnitude of this increase declines as the pressure goes up. Under the same stressing intensity, the product size distribution curve becomes steeper as the particle size decreases, so there is no self-similarity between product size distributions of different feed sizes. The suitability of a material-characterization model for interparticle breakage was verified for this ore. In addition, the effect of interparticle breakage on comminution of this ore with respect to its influence on the downstream flotation were analyzed in terms of size-metal distribution and mineral liberation.

Jan 1, 2016

By Y. Y. Li, Q. Chen, Y. X. Cai, Q. Zhang, S. Mao

"Due to the influence of combustion conditions, the fly ash produced by some power plants has the problem of high-carbon content. The unburned carbon in fly ash can be removed by flotation, and the decarbon tailings should reach the national standard level I fly ash. The fineness of the requirement is one of the important indicators and is also an important factor affecting the tail ash activity. In this paper,adopting two methods investigate the effect of particle size on the flotation index: one is direct flotation of fly ash, and the other way is wet grinding + flotation of fly ash, comparing the two methods and selecting the appropriate process,which provides a way for the effective utilization of fly ash. INTRODUCTION Fly ash is a solid waste discharged from coal-fired power plants. The annual amount of emissions of fly ash are very large in China. The amount of fly ash were discharged from coal-fired power plants are increasing gradually, and the amount of fly ash stored has exceeded 2.5 billion tons, but the comprehensive utilization of fly ash is not high, which brings about a huge environmental problems( Lu et al.,2011). Carbon is a harmful component of fly ash in cement and concrete application (Zhang et al.,2008). Fly ash decarburization is an essential link to improve the utilization efficiency of fly ash and the reduce pollution ( Yang et al.,2012). Carbon is selected from fly ash to make full use of fly ash resources and improve utilization of fly ash (Li et al.,2008). In this paper, the flotation decarburization of high-carbon fly ash is studied, through comparing the grinding and not-grinding processes, optimizing the separation process of fly ash, which provides a way for the effective utilization of fly ash."

Jan 1, 2018

By B Wu, B W. Lei, B J. Duan

When a coalmine fire occurs, it is crucial to judge the developing trends inside the fire area by analysing the changes of gas concentration in order to formulate the proper rescue measures. At present, few researchers have focused on the relationship between the changing trend of gas product and basic characteristics of fire in the coal fire extinguishing process. To study the relationship of basic characteristics of coalmine fire during the extinguishing process, an experimental platform for coal combustion in a confined space was built, and gas production, flame image and coal temperature during the extinguishing process were monitored and analysed by an online continuous gas analysis instrument, camera and thermocouple. Research shows that during the burning phase of the coal sample in the confined space, the flame zone decreases gradually due to insufficient gas supply. The size of the flame zone fluctuates and shares a positive correlation with CO concentration, while sharing a negative correlation with O2 and CO2 concentrations. Then, in the extinguishing phase, the increasing rate of CO2 concentration and the decreasing rate of O2 concentration both decrease gradually, but CO concentration would rise for a period before it eventually decreases. Coal temperature continues to rise in the open flame stage and does not go down until the flame is extinguished.CITATION:Lei, B W, Wu, B and Duan, B J, 2015. Experimental study on extinguishing characteristics of coal fire in confined space, in Proceedings The Australian Mine Ventilation Conference, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By Xiaohong He, Qing Yu, Kaixiang Zhang, Rui Guo, Minghua Lin, Haoyu Miao

With the increasing depth of coal mining, the coal mine shaft traverses’ strata conditions become more and more complex. Shafts are often located in deep thick strata with unstable aquifers, and coal mining requires short-term rapid drainage of aquifers; the additional stress caused by aquifer water drainage is the direct cause of the shaft-lining failure. Over the years, many experts have conducted research on the shaft-lining damage caused by the consolidation and subsidence of the soil layer induced by the long-term drainage of the aquifer. On this basis, this paper conducts an in-depth study of the dynamic change of the pore water pressure of the aquifer in the short-term drainage and its influence on the response of shaft-lining strain and surface subsidence. The result shows that the Mandel effect of pore water pressure around the shaft-lining is obvious at the beginning of drainage, and the pore water pressure suddenly increases; the increase is independent of the drainage rate, which leads to the sudden increase of the shaft-lining strain value unrelated to the drainage rate. The result also shows that with the gradual dissipation of pore water pressure, the increase of shaft-lining strain is positively related to the drainage rate and negatively related to the drainage distance, and the variation trend of horizontal strain is greater than that of vertical strain, which appoints the main cause of shaft-lining damage.

Mar 16, 2023

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By R. Kong, X. W. Zhang

"High pressure (up to 50 MPa) isotropic compression tests were performed on marble, gneiss and sandstone specimens, of which represents the typical rocks, to investigate isotropic compression deformation characterization at room temperature. Experimental data with respect to volume change in loading and unloading are presented. An apparent volume change inflection point (sensitive stress) was observed at a lower pressure range for porous sandstone, indicating that the elastic-plastic behaviour arising in the isotropic compression stage, but for tight crystalline rock, the sensitive stress is much higher, not probed prior to 50 MPa. The irrecoverable volumetric strain in the unloading can be seen for sandstone as well. The anisotropic deformation was discussed in terms of the axial and radial strain measurement. It was found that essential features of mechanical anisotropy are the irreversible in deformation range. The deformation feature in the isotropic compression tests is a very complex issue due to the factors concerning the stress history, unloading in sampling and in-situ stress. INTRODUCTIONThe isotropic or hydrostatic compression condition that stress is compressive and has the same magnitude for all direction, which is expressed as s1=s2=s3 in principal stress space. A yield locus of soils subjected to the isotropic and anisotropic compression was widely known, for instance Cam Clay model, which forms a closure cap model. However, the similar isotropic compression yield curves for rocks, especially for hard rock, was not established due to the geo-stress in the rock mass is much less than the socalled isotropic yield stress. And hence, the previous experimental studies on the hard rock have been made tend to on the stress-strain-strength relationship (Handin & Hager, 1957; Edmond & Paterson, 1972; Menéndez et al., 1996). Perhaps the yield curves related to an increasing in the hydrostatic pressure is not forced to construct for hard rocks, undoubtedly, the deformation data in this processing is valuable to assess the bulk module (Fabre & Gustkiewicz, 1997), anisotropy (Niandou et al., 1997), field stress (Hakala et al., 2007). Furthermore, many rocks store much elastic volume strain energy link to the hydrostatic pressure exerted, following a deviator stress applying, to drive the unstable brittle fracture for hard rock. Latter was studied to interpret the incentive of rock burst. However, volume change characteristic in the isotropic compression behaviour have been scarcely studied experimentally to our knowledge, less application related to the fracture in hard rock as well. The mechanical behaviour in the isotropic compression of hard rock is notably affected by the original structure anisotropy, stress history and stress condition before sampling, all of which need reasonably assess. It is also a useful understanding to study isotropic compression that elastic and plastic volume change in the isotropic loading and unloading, and the micro crack evolution throughout it."

Jan 1, 2015

By Takeshi Maki, Kh. Adeel Tariq

"The lateral resistance of the structure plays an important role during seismic event and it can be increased by using ground improvement. In this study an attempt has been made to investigate the effect of cement-treated sand on the lateral capacity of the pile. The behavior of piles surrounded by sand only and cement-treated sand confined in a steel box (30 x 30 x 50 cm) which is subjected to lateral cyclic load has been investigated. Piles having a diameter of 2.5 cm and embedded to a depth of 45 cm were used. Steel and aluminum piles were used to investigate the effect of flexural stiffness on the lateral capacity of the pile. Bottom supports of piles were also changed from pinned to fix. Well graded sand compacted to 70% of relative density (RD) was used. Cement-treated sand having a compressive strength of 3.7 MPa was used. Displacement controled lateral load tests were performed and cyclic loads were applied until pile displacement was 4%, 10%, 20%, 35%, 50%, 75% and 100% of pile diameter. Results evaluated are compared with common method of analysis like Brinch hansen (1961), Brom (1964), Poluos (1980) etc. Results have indicated that the stiffness of a pile affects its lateral capacity. The introduction of central cement-treated sand part increased 5 times the lateral capacity of piles as compared with a sand only condition.IntroductionPiles are used extensively around the world to support loads of structures. Piles are commonly used to carry axial load, but in some structures, the lateral capacity of the pile is more important than the axial capacity: for example piles supporting earth retaining structures, electric tower foundation, etc. Structures can be subjected to both axial and lateral forces, like structures constructed at harbor that are subjected to lateral force due to waves action; and structures built in earthquake prone areas like Japan."

Jan 1, 2017

By L. J. Han, Y. J. Zong, S. Y. Wen, J. J. Wei

"Stress strain curves characteristics, deformation and strength properties, and failure process and characteristics of sandstone samples under different stress states were analyzed through triaxial compression tests carried on using TAW-2000 microcomputer control electro-hydraulic servo rock triaxial test system. The experimental results reveal that peak strength, residual strength, elasticity modulus and deformation modulus increase linearly with confining pressure, and failure models transform from fragile failure under low confining pressure to ductility failure under high confining pressure. Macroscopic failure forms of samples under uniaxial compression was split failure paralleling to the axis of samples, while macroscopic failure forms under uniaxial compression was shear failure, the shear failure angle of which decreased linearly with confining pressure. There were significant volume dilatation properties in the loading process of sandstone under different confining pressure, and then based on acoustic emission damage and volumetric dilatation damage the damage evolution properties of samples were analyzed, and damage constitutive model were established, realizing the real-time quantitative evaluation of samples damage state in loading process. INTRODUCTIONDamage is a phenomenon that micro defects in material under monotonic loading or reloading will lead to progressive decrease of the cohesion and damage of volume units. Many scholars at home and abroad have carried out systematic researchers on damage evolution characteristics and constitutive model of rock, and have achieved a series of remarkable results in this field. Lu Y.D. (2004) studied the complete stress-strain curve’s characteristics of marble under triaxial compression, and established the bilinear elastic-linear strain softening-residual ideal plastic damage constitutive model. Ren J.X. (2001) studied the damage evolution laws of coal and rock mass by computerized tomography triaxial loading system, realizing the quantitative evaluation of damage state. Zhang Z.L. (2011) studied the deformation and failure mechanism of strong weathered sandstone by triaxial compression test, and analyzed the damage evolution processes and established the damage evolution equations based on the density method. Li X.J. (2012) studied the microscopic damage characteristics of siltstone under triaxial compression by scanning electron microscope and digital image technology, and analyzed the statistical distribution characteristics of cracks azimuth angle, length, width. Zhou J.W. (2012) studied the strength, deformation and fracture damage characteristics of sandstone by uniaxial cyclic loading and unloading tests, and defined damage variable based on linear damage mechanics theory and acoustic emission (AE). Cao W.G. (2006) established a new damage model and a statistical damage constitutive model of rock under specific confining pressure according to the force of damaged part and undamaged part in rock on the base of statistical damage theory. Li S.C. (2014) studied the damage evolution characteristics in the whole uniaxial compression process of sandstone by electrical resistivity and AE, and proposed a status qualitative criterion for rock damage."

Jan 1, 2015

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By J. D. Zhou, F. Yang, X. G. Bi

"In this investigation, the phosphorus distribution ratios in the CaF2 system and B2O3 system dephosphorization slags for high-phosphorus hot metal pretreatment were measured by an indirect method under laboratory conditions. Firstly, the phosphorus distribution ratio between liquid slag and solid iron was measured, and then the phosphorus distribution ratio between liquid slag and hot metal was calculated. Phosphorus capacity was calculated in terms of the composition and optical basicity of the slag. Dephosphorization slag was also studied by scanning electron microscopy, energy dispersive analysis, and X-ray diffraction analysis. The experimental results show that the phosphorus capacity of the B2O3 slag system is much greater than that of the CaF2 system. It is demonstrated thatB2O3 can completely replace CaF2 as fluxing agent for high-phosphorus hot metal pretreatment. With CaF2 as fluxing agent, the phosphorus capacity increases with increasing CaO content in the slag, but the phosphorus distribution ratio decreases. B2O3, when used as fluxing agent, can react with high melting point phases such as 2CaO·SiO2 and 3CaO·P2O5 in the slag to form new phases with low melting points such as 11CaO·B2O3.4SiO2, 2CaO·B2O3.SiO2, and Ca9.93(P5.84B0.16O24) (B0.67O1.79), thereby acting as a fluxing agent. When the ratio of w(B2O3)/w(CaO) is 0.16, the phosphorus distribution ratio reaches its maximum value, that is, the dephosphorization ability of the slag is at its maximum. IntroductionAs international iron ore prices continue to rise, the development of China's steel industry is facing a lot of pressure. Against this background, development and utilization of domestic high-phosphorus iron ore resources is particularly important. When highphosphorus iron ore is used in ironmaking, the phosphorus content in the hot metal can reach 0.35% or more, and the hot metal must be pretreated. For hot metal with 0.08–0.10% dissolved phosphorus, the traditional hot metal dephosphorization pretreatment technologies are relatively mature. However, when using these methods to dephosphorize hot metal containing 0.35% P or more, the amount of dephosphorization slag can reach 100–150 kg per ton of hot metal. Furthermore, the traditional dephosphorization methods require the addition of large amounts of CaF2 as fluxing agent, and this results in high fluoride levels in the dephosphorization slag. The fluorine in the slag can partially dissolve in water and thereby causes high fluoride concentration in the water and soil. Once the fluoride is absorbed by humans or animals, it can result in toxic effects on the central nervous system and myocardium. In addition, fluoride can accumulate in the environment, and thereby pose a health risk to animals and humans through the food chain (Li, 2007; Liu, Wang, and Dong, 2011, Diao, 2013). The objective of this research is to replace CaF2 with B2O3 as fluxing agent while achieving the expected goals of hot metal pretreatment."

Jan 1, 2016