Search Documents

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By Y. Foucaud, C. Eswaraiah, L. Filippov

Enhanced gravity separators such as Falcon concentrator which uses additional centrifugal force, are the most common gravity concentration techniques used for fine particles processing. Hence, understanding the kinetics and separation mechanisms within these separators is of paramount interest. Recent research yielded a predictive physical model for the Falcon Ultra Fine (UF) which however does not explain some results obtained with industrial ores. This study aims to identify the mechanisms involved in Falcon UF separation with the objective of confirming or rejecting the hypotheses on which the current model is built and suggesting potential points of improvement. The Falcon UF kinetics is investigated through the processing of complex low-grade and fine-grained ores from the Altenberg tin deposit (Germany), the Tabuaço tungsten deposit (Portugal) as well as a synthetic iron ore. Saturation tests are performed on the Falcon UF by controlling the separation efficiency in terms of recovery and enrichment ratio with time or feed mass. Results show an evolution of Falcon UF performance with time in contradiction with the stationary separation hypothesis on which the physical model is based. Observation of the concentrate bed suggests the presence of erosion figures in furrows which may play locally an active role in the separation. In terms of Falcon UF separation timing, three phases can be distinguished. First, upon initial feeding of the bowl, a bed quickly grows unselectively and ultra-fine particles are ejected from the bowl until the bed reaches its final profile. Next, actual separation occurs with selective concentration of dense particles. Finally, capture sites saturate and recovery drops. The evolution of partition curves over time confirms the existence of two separation mechanisms. First, differential particles settling within the flowing film responsible for the ejection of small size particles during the whole separation cycle which is already accounted for in the physical model. The second mechanism involved may be explained by the action of lift force, neglected in the physical model, which acts preferentially on coarse particles deposited at the surface of the bed resulting in coarser particles being rejected in the tailings. Hence, the addition of a lift force component to the existing model is suggested to account for this second separation mechanism.

Jan 1, 2018

By Jelke Dijkstra

This paper presents the results of model pile load tests in a photoelastic material. The soil in this test is represented by an assembly of photoelastically sensitive glass particles, which allows for optical measurements of stresses. In the same test setup, displacements around the pile are measured using digital image correlation (DIC). During the pile installation stresses and strains are recorded. Tests were performed in loose and medium dense particle assemblies. The development of stresses and strains around the pile tip and pile shaft are quantified and presented in this paper. For the loose conditions the results show a small influence on the stress state. For the medium dense conditions a clear stress change is observed.

Jan 1, 2006

By Emily Johnson, Catherine Johnson, Ben Sonpon, Kelly Williams

The effect of length to diameter of the detonator is compared using Ansys/Autodyn 2-D simulations, the results of which are validated experimentally. It was found that higher pressure comes with a larger diameter, because it will result in more explosive energy being allocated out the end of the detonator.

Feb 1, 2020

By J. Dionne

"Next to the actual mine of Les Explorations Muscocho Ltée in Montauban, Quebéc, you could find a total of 364 000 tons of flotation tailings assaying 1.4 Au g/t et 82 g Ag/t to the south of the municipality. This tailings pile is what is left of previous operations. Preliminary leaching tests on these tailings in laboratory columns gave interesting results which led to tests in larger columns in 1984 and to a pilot test on a 750 ton heap in Montauban during the summer of 1985.This paper briefly describes the columns tests performed at the Centre de Recherches minérales and the heap leaching test designed and conducted by SOQUEM in Montauban. It also presents the results obtained.RESUMEPrès de la mine actuelle de Les Explorations Muscocho Ltée à Montauban, Quebéc, se trouvent, au pied du village, 364 000 tonnes de rejets de flottation titrant environ 1,4 g Au/t et 82 g Ag/t. Ce tonnage de rejets représente ce qui reste de l'opération des anciennes mines de Montauban.Des essais préliminaires de lixiviation en colonne sur ces rejets ont donné des résultats encourageants. Ils ont été suivis en 1984 par des essais en colonnes plus volumineuses et par un essai pilote à Montauban en 1985 sur une pile de rejets de 750 tonnes.Ce te x te donne une brève de script ion des essais en colonne effectues au Centre de Recherches minérales et de l’essai pilote planifie et exécute à Montauban par SOQUEM. Il présente les résultats obtenus."

Jan 1, 1987

By O. Salami, G. Xu

Fire accident is one of the most classic safety concerns in underground mines both in the USA and abroad. It may occur from pool fires due to leakages in hose or pipes, vehicle fires, or fires in tires and conveyor belts in the underground mines. It may also result from the storage of flammable materials such as gasoline, diesel, and explosives in the underground. When fire occurs in an underground mine, it releases heat, smoke, and other toxic gases such as carbon monoxide, and methane to the surrounding thereby making life unbearable to the miners. Furthermore, smoke greatly impact visibility in the underground which makes evacuation even more onerous and challenging. To this end, a thorough investigation of fire behavior and spread of toxic gases in a practical underground mine is imperative to develop a reliable emergency evacuation plan in an event of fire disaster in the underground mine. The objective of this study is to investigate temperature variation and CO spread along mine airways by conducting full-scale fire experiment in the underground mine. The results presented from this study are crucial to developing evacuation plans in underground mines. In addition, the findings from this study could be used to validate existing evacuation models.

Mar 2, 2022

By D. B. Barker, D. C. Holloway, J. F. Cardenas-Garcia

Tround International Inc. is currently developing a hard rock drill that uses a salvo of three frangible projectiles to prefracture the rock ahead of a conventional tri-cone bit. This paper reports on a series of experiments conducted for Tround to study the fragmentation enhancement possible through the use of an optimally timed and spaced salvo of projectiles. In this study the complex three-dimensional problem was simplified to a two dimensional salvo impact problem in a transparent brittle plate of glass. The use of high speed photography and dynamic photoelasticity was then used to study the development of the impact damage zone and the various interactions of the stress waves.

Jan 1, 1982

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016

By K. Kar, M. Gautam, J. T. Jurewicz

The 10-mm Dorr-Oliver cyclone has been widely used as a personal sampler for size selective sampling of particles within the respirable range (Dp < 10 gm). Because of their inertia, the particles are unable to follow the swirling flow (outer vortex) within the cyclone. The particles migrate to the bottom of the cyclone, depending on their size, and get trapped into the inner vortex which leads to an eventual blow-off from the top of the cyclone. By measuring the size distribution of the particles in the free stream and in the collected sample, the aspiration efficiency of the cyclone can be calculated. Velocity difference between the free stream and sampling velocity. Inlet orientation, particle impaction and deposition, particle inertia and free stream turbulence result in the departure of the aspiration efficiency from unity and this, in turn, leads to inlet bias. Although the effect of inlet bias on sampling efficiency has been investigated in past, the results lack detailed information and show only some general trend. In this effort, a systematic, in-depth experimental work on the effect of inlet bias on the sampling efficiency has been undertaken using non-intrusive Laser Doppler Anemometry (LDA), Aerodynamic Particle Sizer (APS) and impactors.

Mar 1, 1992

By G. G. Krishna Murthy

Several experiments were carried out to simulate the bath smelting reactions where iron oxide particles were dropped on to an iron-carbon bath containing molten CaO-SiO2-Al2O3 slag layer on its surface. The composition of the slags used in the experiments was %CaO:46.1; %SiO2:41.7; and %A1203:12.2. Experiments were con¬ducted with carbon saturated iron melts contained in either a pure graphite crucible whose walls were covered with a pure alumina tube, or a pure flat bottom alumina crucible, at 1723-1823 K. Degree of reduction of a pure iron oxide particle was linear with time in the initial stages (up to about 20% oxygen of the original pellet was reduced). The rate of reduction of smaller oxide pellets was smaller than that of a bigger pellet - the time for complete reduction of a 5.6 g wustite pellet was smaller than that for a 1.2 g wustite pellet. It was also established that the interaction rates obtained by adding a molten pure oxide particle of given weight to the system were lower than that determined by using a solid oxide particle of same weight. The overall rates of reduction decreased with decreasing the bath temperature. The experimentally determined rates of reduction based on the time for 70% reduction were influenced substantially by addition of slag up to about 50 g on to a bath of 78.8 mm in diameter, and remained constant when slag present on the bath surface was between 50 g and 200 g.

Jan 1, 1993

The slags produced by the Imperial Smelting Process (ISP) are based on the system ZnO-?FeO?-Al2O3-CaO-SiO2. The slag chemistry is important to the process since it determines the fluxing practice and the operating temperature of the furnace required to produce fluid slag. The paper presents the results of the first systematic experimental investigation of these ZnO-containing slags in equilibrium with metallic iron, and provides information on the primary phase fields and liquidus temperatures in these slags over the range of compositions used in ISP practice. A feature of the slags is the presence of alumina, which has a major influence instabilizing the spinel phase. This information presented in the form of pseudo-ternary sections ZnO-?FeO?-(Al2O3+CaO+SiO2) enabling the data to be readily used by plant engineers. Keywords: liquidus temperature, ISP, EPMA, ZnO-?FeO?-Al2O3-CaO-SiO2, phase equilibria.

Jan 1, 2004

By Eiki Ono, Atsushi Yamatodani, Shigeru Sunagawa, Yasushi Takasaki, Atsushi Shibayama, Yasunori Higuchi

"During metallurgical processing of non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product.In this research, some experimental feasibilities were investigated to recover/remove Cu and As from the residue. Primarily, the removal of As and volatilized materials from the residue was examined by pyrometallurgical treatment (dry-process). In the second stage after treating the residue with a dry-process, leaching and solvent extraction as hydrometallurgical treatments (wet-process) were also investigated by using H2SO4 solution as a two stage leaching treatment, to dissolve various metals from the leach residue. Then, solvent extraction was examined by using LIX-84I as an extractant to recover and separate Cu from impurities from the final (2nd) leached solution. For the leaching stages, the removal of 90 % As and the leaching rate of 85 % Cu could be achieved by 0.25 mol/l and 1.0 mol/l H2SO4 solution, respectively. On the other hand, the extraction of over 90 % Cu and stripping was carried out by solvent extraction. 1. IntroductionIn metallurgical process for non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product, i.e., flue dust, slug and so on. The smelting residue includes some useful metals and undesired toxic materials; Cu, Pb, Ca and As, etc.In Japan there is one undisclosed place stockpiled with 10,000 ton of smelting residue from abandoned smelters about 25 years ago. Therefore it is necessary to reduce the residual amount for space and environmental protection including water treatment by separating and removing toxic materials."

Jan 1, 2008

By R. Pelletier, Herny. E., C. Allaire

Corrosion of refractory linings by molten metals is controlled by interactions between penetration and chemical reaction. Corrosion of aluminosilicates by molten aluminium is no exception. The early stage of corrosion can be described as a particular case of reactive wetting over a porous medium. Although the reactivity between aluminium and silica is great, which should improve wetting and penetration, the presence of air and the formation of a protective oxide layer disfavours initial penetration. This paper presents the results of an exploratory study on the effect of some parameters on the initial stage of aluminium penetration. Penetration kinetics and metal intrusion tests have been performed on alumina and silica powders with pure aluminium and Al¬5%Mg. Capillary models are used as tools of interpretation. Penetration kinetics tests had a poor reproducibility and the kinetics itself can not be explained very well by the capillary-tube-bundle model. On the other hand, a capillary model initially developed for ice intrusion into freezing soils produced predictions in reasonably good agreement with intrusion pressure measurements. The effect of particle size and alloy composition can be predicted using this model. However, the effects of temperature and powder chemistry need additional interpretations to be rationalised. An unusual resistance to penetration of silica powder by molten aluminium have been observed in a series of experiments. This led the authors to the strange conclusion that oxygen should be seen as an excellent non-wetting agent and that there might be ways to use it in industrial applications.

Jan 1, 2004

By A. Shibayama

Soil contamination by organic compounds is one of the most concerned issues on polluted soil. It is well known that there are limited methods to remediate the contaminated soil on site. Especially, the in-situ method for contaminated soil is too difficult to de-contaminate the organic pollutant. In this study, the fundamental ability of soil remediation, which aimed to decrease oil concentration in, in-situ process, have been researched by using a high pressure gas generated from ?crush composition? on artificially oil contaminated soil. The n-hexadecane (n-C16H34) and other organic compounds were selected as soil oil contaminators, gravimetric analysis by soxhlet extraction and GC-MS were used as qualitative and quantitative analysing methods. For the experimental examination, the influences on the difference in the concentration of n-hexadecane (and other organics), the tamping amount, position and repetition of crush composition in soil, and scale (size) of experimental model were investigated. The n-hexadecane concentration reduced by the explosive effect of crush composition showed a reasonable decrease of about 30 wt%~60 wt% compared to the initial n-hexadecane. The removed amount of n-hexadecane and distance from explosion point of the crush composition was related in scale and model of contaminated soil.

Jan 1, 2014

By Frederick C. Trutt, Jeffery L. Kohler, Joseph Sottile

Condition-based maintenance (CBM) of industrial equipment is generally recognized as being the most cost-effective means for improving equipment availability. However, prerequisite to successful implementation of CBM is a reliable detector of failing components. One such detector, termed the effective negative-sequence impedance, had previously been identified as an indicator of induction motor stator winding degradation. However, a limitation of this detector is that it does not change in a predicable manner under certain motor operating conditions. This paper presents an experimental investigation of an improved technique for on-line detection of induction motor stator winding degradation. The paper begins with a brief description of the detectors, followed by a detailed description of the experimental setup, the experiments conducted, and results.

By Minna Rämä

Iron containing leach residues like jarosite and goethite from electrolytic zinc production contain many valuable metals and harmful substances. These metals and substances should be removed in order to obtain an acceptable, stable and reusable product, and maximize economic feasibility as well as minimize environmental footprint. In this work, the processing of jarosite leach residue was studied in laboratory scale experiments under oxidizing and reducing conditions at high temperatures. First, the pretreated material was melted and oxidized to produce a melt of metal oxides. Second, the oxide melt was reduced in CO–CO2 atmosphere. Target after the reduction step was to obtain a clean slag and a liquid metal or speiss phase that collects the valuable metals, such as silver. The kinetics of the thermal processing were studied for determining optimal times and conditions for the aforementioned process steps. The preliminary results show that the process is thermodynamically feasible, and the desired phases can be obtained in the experimental conditions investigated.

By Patrick M. Eduafo, Brajendra Mishra, Mark L. Strauss

Direct acid leaching of rare earth metals (REMs) from waste lamp phosphors is non-selective, leading to co-dissolution of impurities mainly calcium, phosphorus, silicon, iron and zinc. Calcining the phosphor powder at different temperatures followed by leaching with HCl isn’t efficient for the extraction of all the chief rare earths especially cerium (Ce), lanthanum (La) and terbium (Tb). Therefore, multi-stage leaching operations are required for the separation of the REMs in phosphor dust. This paper will outline a new process for extracting Ce, La, Tb, Eu and Y from waste fluorescent lamps using a three-stage leaching and separation process. A flowsheet has been developed which shows this process is selective and efficient.

Jan 1, 2015

By J. F. White

An experimental study was undertaken to evaluate the feasibility of a selective chloridizing roasting pre?treatment process for the elimination of impurities from zinc feed?stocks prior to recovering zinc by conventional unit operations. In this investigation, a number of chemistries that might serve as a basis for such a pre? treatment process were examined. A variety of chloridizing agents were admixed with EAF dust to promote the selective removal of lead and cadmium by the formation of volatile metal chlorides, he results of the experimentation firmly establish that selective chloridizing roasting is a technically feasible means of eliminating lead and cadmium from EAF dust. Excellent extraction efficiencies were accomplished with a number of chloride additives; as high as 98 percent lead extraction and 88 percent cadmium extraction were attained with minimal zinc losses, Continuous pilot?scale tests reinforced the trends established by laboratory?scale experimentation, Attempts of chlorine elimination using pyrohydrolysis were less successful. The extent of chlorine elimination was found to be highly dependent upon EAF dust sample type and treatment temperature.

Jan 1, 1996

By P D. Katsabanis, W Roberts

Commercial explosives exhibit non ideal behaviour which is very difficult to model. The fume spectrum produced by commercial explosives apart from its practical significance for underground mining is of great theoretical importance since it reveals information about the chemistry of the detonation process. Emulsions, watergels and dynamites were tested under various degrees of confinement in an one cubic metre closed chamber. Sand, concrete, steel and copper pipes were used to alter confinement. The degree of confinement was found to significantly influence the quantity (litres/kg of explosive) and the relative proportions of toxic and non-toxic fumes (percent of total fume measured). These results lead to further confinement testing using various rock materials. Fume results, and thus detonation performance were found to be dependent on the type of rock material used for confinement. Materials such as dolomite, limestone, and granite were found to result in a relatively high detonation efficiency of the subject explosive as shown by the distribution of detonation fume products. Conversely materials such as sandstone, talc and massive sulphide resulted in fumes suggesting low relative detonation efficiency. Fumes appear to be a sensitive indicator of the completeness of reactions occurring within the expansion zone of the composite emulsion explosive, while the detonation velocity is relatively insensitive to small variations in confinement. Estimates of sonic velocities of the confining rock materials were found to show no correlation with VOD results. However good correlation between fume results and sonic velocity suggests that the performance of an explosive as indicated by the resulting fume spectrum is affected by the degree of confinement.

Jan 1, 1992

By S. Nikolic, O. O. Kehinde-Philllps, O. T. Djamgouz, D. H. Rousell

"A bulk mining method is employed at the Lockerby mine resulting in the formation of large muck-piles. If these muckpiles remain in the stopes for some time they may agglomerate to the extent that the muck cannot be removed by a scooptram. A laboratory investigation was undertaken with sulphide material from the mine in order to detemine the time that oxidation begins and the flowability of the material as a f unction of several factors. The laboratory results are applied to the conditions in the muck-piles.The time of the beginning of oxidation of the material decreases as the sulphide composition, water content and availability of air increases. Oxidation is retarded by the addition of a copper sulphate solution instead of water. The unconfined yield force (strength} of the material increases with an increase in the sulphide composition, water content and time. The material ceases to be free-flowing before there is visible evidence of oxidation and this suggests that oxidation actually begins earlier and that agglomeration is also due to the capillary action of water.Broken ore should be removed from the stope prior to the time a muck-pile ceases to be free -flowing-perhaps as early as two days f or high-grade ore and 5 days f or low-grade ore. In order to control dust, 1.4 weight per cent of a 5 per cent solution of copper sulphate should be added 10 the muck-pile rather than water. This inhibits oxidation and increases the time that a muck-pile remains free-flowing."

Jan 1, 1984