Search Documents

By Frank J. Tolonen

BENEFICIATION of iron-bearing formations is one of the major problems of research at the Michigan College of Mining arid Technology. Funds for this purpose hate been supplied by the State of Michigan supplemented by contributions of labor and some supplies from the Federal Government during the depression. The iron-mining companies have cooperated in securing samples and have also furnished much valuable information relative to the various formations.

Jan 1, 1937

THE Johnson award for 1926 was given to T. L. Joseph for his experimental work on blast-furnace operation. When the Bureau of Mines undertook its experimental blast-furnace investigation in 1919, a number of operators and metallurgists were doubtful as to the practicability of small-scale tests. Several pre-vious attempts, outside the Bureau, to operate small furnaces had been unsuccessful. However, pig iron was produced in three and four-ton furnaces during the first half of the nineteenth century. The operation of a small furnace did not therefore seem an impossible task. This point of view, together with a realization of the importance of problems connected with the pro-duction of pig iron, prompted the Bureau to undertake this work. Such problems as the feasibility of using charcoal briquets as a fuel, the application of oxygen enriched blast, and the use of new ores and raw ma-terials, in general, can be investigated only at consider-able cost on full sized furnaces, while with an experimental furnace they can be conducted at a com-paratively ;small, cost. The results of small-scale tests are sufficient to determine whether the problem. War-rants the expenditure required for a trial on a com-mercial scale. The accompanying photographs and chart show the various stages of the experimental furnace development. Some idea of the size and shape of furnaces which were tested can be had from the development chart. In oper-ating furnaces A to F, a series of changes were made to increase hearth temperature. Perhaps the most im-portant change was the position of the tuyeres with respect to the bottom of the hearth. The height of the tuyeres above the hearth was gradually increased and the hearth diameter decreased. It was shown by this series of furnaces that metal and slag are the chief source of heat supply to the crucible. For this reason there is a minimum rate at which these materials can be brought into the hearth of a small furnace if it is to function properly. The rate of slag "and metal fall are determined by the burden on the furnace and the rate of blowing. Due to lack of funds necessary to provide ample blowing equipment, hot blast stoves, essential mechani-cal features, and to meet operating expenses, it. was necessary to work with much smaller furnaces, such as G to K shown in the chart. The particular object of these tests was to study the extent to which reactions could be speeded up by decreasing the size of the stock. One decided change, noticed at the beginning of this series of tests, was the effect which coke size had on the production of a strongly reducing gas. Furnace G, 22 in. high, operating on coke crushed to pass 10 mesh, made a gas richer in carbon monoxide than did fur-naces A to F, operating on run-of-the-oven coke.

Jan 3, 1927

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Ziyan Ouyang, Haotian Zheng, Spencer Quiel, Mike Mooney, Clay Naito

This paper summarizes the results of an experimental program conducted to characterize the moment-rotation behavior of skewed flat radial joints from large diameter (45 ft) tunnel lining. Both positive and negative joint moment-rotation behaviors were measured experimentally using two-segment joint combination assemblies. The results are compared to closed form methodologies used by designers, e.g., the Janssen method. The differences in observed and model behavior are discussed within the context of design practice.

Jun 23, 2024

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By J. R. Katan, J. R. Ball, Peter R. Bannister, F. J. Williams

During the last week in March and the first week in April, 1973, the Naval Underwater Systems Center measured the 76 Hz magnetic field strength (in Wisconsin and Texas) produced by both the elevated and (newly installed) buried Wisconsin Test Facility (WTF) north-south (NS) antennas. The principle result obtained from these measurements is that there is no measurable difference in performance between the WTF buried and elevated NS antennas.

Jan 1, 1973

By J. K. Wilmshurst

Absorption, emission and reflection techniques for the study of [molten] inorganic materials at high temperatures have been critically examined. In general, the reflection technique is the most satisfactory for tine study of pure materials, while the absorption, and possibly also the emission techniques, may be useful for studies of certain dilute solutions. In the present investigation infrared emission spectra for sodium nitrate and silver chloride were obtained together with absorption spectra derived from reflectivity data by the method of Robinson and Price for sodium nitrate, silver chloride, lithium and potassium fluoride and their 1:2, 1:1 and 2:1 mixtures and for solutions of zirconium tetrafluoride in lithium-potassium fluoride (1:1) and sodium-potassium fluoride (1:1). It is concluded that vibrational spectroscopy cannot give unambiguous information concerning the existence of complex ions in fused salt, mixtures.

Jan 1, 1963

By Paul Worsey

A strong inverse relationship between rock face movement and stemming ejection is presented. Previously unpublished data from blast control plug research and development involving high speed video analysis, which was conducted between 1986 and 1988, is presented. Face and stemming ejection velocities were calculated for tests utilizing the same bench blasting configuration comprising; a 4 ft high bench in dolomite, 3 ft burden and single 1.75 in. holes loaded with 2 ft of small diameter cartridge emulsion. The singular difference between these tests was the stemming configuration. Varying lengths of stemming were used with the presence or absence of differing experimental configurations of blast control plug. The effectiveness of this plug has been published previously.

Jan 1, 1990

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-In this exposition of experimental data, the author infers, indirectly at least, that by the Charpy test information was obtained that led to the improve-ment of certain ordnance parts and that this improvement could not have been attained without the Charpy test. On examination of the data, however, it appears that the important point of the whole matter was that while the material had been accepted from the results of longitudinal tensile tests, it was really transverse ductility that was desired. The writer has no desire to attempt to detract from the value of the paper or to discredit the Charpy test in any way, but he would like to ask the author if he will not give more clearly his reasons for preferring the Charpy impact test for investigational and control work of this kind, over the more usual tensile test made in a transverse direction. The tensile test pieces are more cheaply made than the square notched impact bars; and from the former the limit of elasticity and the ultimate strength as well as, the ductility are obtained, while in the Charpy test only one property is measured. It does not seem that the author has shown a sufficient reason for favoring the latter test, when both it and the trans-verse tensile test served his purpose equally well in indicating the proper metal and treatment required for his special forging, and it is hoped that this reason will be given more clearly as a matter of useful general information.

Jan 11, 1919

JOHN H. NELSON, Worcester, Mass.-At our plant we have done considerable work on notch-bar testing and are farther at sea now than when we started. So far, we have been unable to get the notch-bar test to be consistent with any other known test. Lately, I have been investi-gating the effect of the position of the notch-bar specimen in a, bar. To do this I took a 3, ½ in. square bar and quartered it, then heat treated the four quarters. Each of these pieces was again quartered and a specimen machined and notched. "In this way we would have notch-bar tests from the exterior to the interior of the bar. These were made of such lengths that it was possible to make four impact tests on each speci-men. Extreme care was taken in marking the position of these test speci-mens in the original bar. The notches were then cut with relation to position of the specimen in the original bar. The second notch was cut 90° from the first, and so on around the specimen. In this way, we have found that, with a 3 ½ in. bar of 0.4 or 0.5. per cent. carbon steel when properly heat treated, we could get impact values ranging from 15 to 100 ft.-lb. Just why this is the case we are unable to state; but it does appear to be a fact that along the outside of the original bar the notch-bar test seems to be low and increases toward the center, but it is not always consistent. For instance, we may have, on a single specimen; one notch-bar test giving us 15 ft.-lb. and another 100 ft.-lb. We have not found such inconsistencies in alloy steels. Alloy steel is consistently good or consistently bad. If it. is good, you cannot readily destroy the impact value, no matter what you do; if it is bad-that is, if it is a poor notch-bar steel-and you have sufficient latitude in your draw, you may correct it. In other words, if the hardness you are working to will allow you to draw to about 1050° F.(561° C.) or over and then quench this steel from the draw heat, you. can raise the im-pact value of the steel from about 4 or 10 ft.-lb. up to-40-or 50 ft.-lb: Just what occurs I do not know. There is evidently a critical-point in steels that have poor impact value, in the neighborhood of 1000 F. to 1050° F. (536° to 561° C.).

Jan 12, 1919

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed' constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011

By M. I. Brasileiro

The use of experimental design to the study of mixtures has found a wide range of applications, even in laboratory scale or in industrial development works. The aim of this work was to maximize granite sawing waste content in ceramic tiles using experimental design. Based on the raw materials, specific formulations were developed using the experimental design. The raw materials were mixed and sample bodies were produced using uniaxial pressing. The sample bodies were fired and characterized in terms of water absorption, mechanical strength and X-ray diffraction. Regression models were adjusted relating the water absorption and mechanical strength with the amount of raw materials. The results showed that the methodology of experimental design maximize the content of wastes incorporated in ceramic tiles formulations. Formulations containing up to 40% of waste can be used for the production of ceramic tiles.

Jan 1, 2009

By Edgardo I. Cifuentes, Andrew L. Mular, Andrew Burkert

Experimental designs are data acquisition plans which, if followed exactly, will quickly provide process engineers with information to assess statistically the individual and joint influence of factors on responses to permit of rapid decision making. Methodology employed to construct data acquisition plans is described in some detail. In production environments, factorial designs are appropriate for most purposes. Use of two level factorials to make decisions is described for a grinding circuit.

Jan 1, 1991

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d'une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By C. C. Clark, S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills that have the transport and deposition properties necessary for a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests tire very limited. This paper presents the findings of investigations undertaken to determine if paste-backfill rheology can be determined using existing techniques and to determine which mix and system variables have the greatest influence on transport-pressure loss. Data from laboratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport-pressure loss.

Jan 1, 1996

By S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills with the transport and deposition properties necessary in a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests are very limited. The following presents the findings of investigations undertaken to determine if paste backfill rheology can be determined using existing techniques and which mix and system variables have the greatest influence on transport pressure loss. Data from lab-oratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport pressure loss.

Jan 1, 1994

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998