Search Documents

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By Shailesh K. Patel, Shaaban Ben-Poorat

In order to ascertain the environmental fate of flotation reagents (fatty acids, fuel oils, and amines) associated with phosphate rock processing with confidence, it was necessary to first establish laboratory methodologies to identify and quantify flotation reagents. This approach was necessitated by the fact that the reagents used in the flotation process are either reclaimed or by-products of other industries and is dictated by their cost. Initially, several blind performance evaluation samples were prepared by spiking water samples with known amounts of either single reagents or reagent mixes and then analyzed. Reagent recovery for the blind performance evaluation samples was within acceptable limits for similar compounds established by the US Environmental Protection Agency. Averification process involving the use of standards and the refinement of analytical methods was utilized to develop standard operat- ing procedures (SOPS) and method detection limits (MDLs) specific to the identification and quantification of the flotation reagents used in the phosphate industry. These procedures and MDLs were critical to support the project's primary goal of assessing the fate of selected flotation reagents in the environment.

Jan 1, 1999

By Arash Habibi, Anna Cable, David Loring, Aleksandar D. Bugarski, Logan Ingalls, Calvin Rutter

The results of diesel particulate matter (DPM) monitoring were used by the underground mining industry to mitigate adverse effects of exposure to DPM. NIOSH Method 5040, currently used for ambient and personal exposure monitoring, does not provide needed real-time information. The objective of this study is to develop a methodology for continuous monitoring of DPM concentrations in an underground environment, founded on the application of the Dekati electrical particle sensor (DePS). The DePS, which measures concentrations of submicron aerosol in real time using a diffusion-charging sensor, was evaluated by comparing the results of the concurrent measurements with reference methods at several locations downstream of the diesel-powered equipment. The DePS results were found to correlate well to those obtained by reference methods. However, it was found that dependence of the response on the physical and chemical properties of aerosols necessitates sitespecific correlation factors for the targeted matrices. The site-specific factors for number and mass of diesel aerosols were derived using the results of concurrent measurements with TSI NanoScan, FLIR Airtec, and carbon analyses performed on the concurrently collected filter samples. The results showed that methodology based on compensated DePS measurements would be suitable for continuous monitoring of DPM in underground mining operations.

Dec 1, 2022

By Connie Travers, Ann Maest, James Kuipers, David Atkins

The science of predicting future water quality at hardrock mine sites has been practiced for at least the past 30 years. As part of the National Environmental Policy Act (NEPA), mines and other industrial facilities in the United States on federal land are required to estimate impacts to the environment, including direct impacts to water quality and indirect impacts that are later in time but still reasonably foreseeable (Kempton and Atkins, 2000; Bolen, 2002). Facilities on private land in the United States may also be subjected to State or federal processes that may or may not require prediction of potential impacts to water resources. Other countries have followed a similar approach, largely based on the requirements of NEPA. A wide array of scientific approaches has been used to predict water quality that could result from construction, proposed expansion, or other action at an industrial facility. In this study, we review the methods and models used to predict water quality at hardrock mine sites, with an emphasis on uncertainties associated with these techniques. Because water quantity and quality are interrelated, methods and models used to predict water quantity will also be discussed, but the emphasis will be on how these methods relate to water quality. This study brings together technical information on water-quality predictions at mine sites in a single paper, and attempts to present a straight-forward approach to using and evaluating the results of the methods and models used to predict water quality at mine sites. Approaches developed primarily in the United States, Canada, and Australia and applied in these countries and in other parts of the world, especially in the last 10 years, are discussed, and the format of the study is geared toward use by regulators of hardrock mines. The approach and results of this study could also be used by environmental managers at mine sites and community groups, and allows for the creation of a checklist for prediction methodology used at mine sites.

Jan 1, 2005

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof-bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60% and 40%, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert and a rigid insert for cleaning the roof-bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the workers coveralls when using either of the inserts.

Jan 1, 2003

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

By S. T. L. Harrison, J. R. Amaral Filho, M. Smart, J. Broadhurst, J. Weiler

Technosol production from mine waste, following amendment with additional organic residues, to provide healthy and functional topsoil is an advantageous alternative to the long-term dump disposal of mine waste. Minimising the legacy of mine waste and supplying soil for mine site rehabilitation contributes towards more sustainable mining practices. Following the creation of the physicochemical structure of the soil from appropriate mixtures of coal waste with low sulfur content, physical ameliorants and nutrient sources, the inoculation of Technosols with active microbial suspensions may accelerate the decomposition of organic matter present and ensure nutrient availability for plant growth through active nutrient cycling, particularly of nitrogen, sulfur and phosphorous. In this paper, South African ultrafine coal waste was used as the main mineral matrix, and malt residue was used as source of organic matter and nutrients. In order to evaluate the effects of Technosol inoculation, five microbial treatments were used, including the addition of: commercial grade efficient microorganisms (EM Prosoil), anaerobic digested sludge supernatant from treating brewery waste, and ‘tea’ extracts prepared from compost, vermicompost and soil native to the mining area. Growth experiments were carried out using Eragrostis teff, commonly known as teff, a grass typically used for the rehabilitation of mined areas in South Africa. Preliminary results showed that Technosols inoculated with microorganisms performed better in terms of nutrient availability and plant growth. Varied performance was observed as a function of the microbial inoculation applied. This suggests that the inoculation of Technosols with appropriate microorganisms may be recommended to accelerate nutrient availability assisting plant growth during the initial establishing of the Technosols. Technosols continue to show promise as an alternative to both mine waste disposal and the burrowing of topsoils for mine rehabilitation. Keywords: Fabricated soil, mine waste, coal discards, malt residue, nutrient availability, soil microbiology, plant growth

Jan 1, 2020

By S. A. Braley

DRAINAGE water from coal mines is probably the most serious water pollution problem today, varying in importance according to location of the mines and geological structure. Drainage may be either acid or alkaline in character. Acid discharge, the most severely detrimental to a stream, is caused by natural oxidation of the sulfuritic material (FeS2) in the strata associated with the coal seam. Since the acid is the result of a natural reaction the acid water differs because it does not cease with abandonment of the mining operations. There is no known economical method of neutralizing acid mine water or any practical method to prevent oxidation of exposed pyrite. Since production of acid from a mine does not stop when mining stops, the total quantity produced depends entirely upon the excavated areas. The increasing volume of acid water in many mines has greatly increased operating costs. Pumping is expensive and acid mine waters are destructive of all equipment, especially metals in pumps and piping, and necessitate the use of corrosion-resistant materials. Discharge of the acid mine drainage into streams neutralizes their normal alkalinity, causes them to become acid, and produces an environment unfavorable for aquatic life and unsuited for industrial or domestic use without costly treatment.

Jan 1, 1957

By Hayati Karaman, Tevfik Güyagüler

In this paper fires due to spontaneous combustion in Middle Anatolian Lignite mine (OAL) which is the first fully mechanized underground lignite mine in Turkey, are studied. Since the installation of mechanization (1986), due to spontaneous heating, four panel fires namely, A01, A02, A03 and A04 have broken out. During these fires, the concentrations of carbon monoxide, methane and the velocity of air are measured continuously by the Micro Minos Environmental monitoring system. For each fire, the environment where fire has started is examined and the possible causes of the fire are investigated. Also the precautions taken to extinguish the fire at different stages are described and the importance of the early detection of mine fire are discussed together with the limitations of the monitoring system and the practical difficulties observed during the fire.

Jan 1, 1995

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.

By V. Gangrade, J. Addis, S. Vanderslice

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are conducting research to improve the ventilation of large-opening underground stone mines. The mine ventilation in these mines are characterized by: (1) challenges related to keeping airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) low pressure losses needed to move large air volumes of air, and (3) costly stoppings needed to direct ventilation airflows. Each of two field studies was dedicated to specific focus areas. The first focus area was the characterization of underground mine ventilation airflow. The primary means of airflow control in stone mines is through the use of freestanding booster fans. The primary goal of this study was to identify the effectiveness of various fan types and optimize their placement. Both traverse and grid-based airflow readings were taken at various distances from the fans, ranging from 70 ft to 425 ft away from the fan. The air readings were taken using a vane-anemometer and a handheld hotwire anemometer. The data was used to develop precise computational fluid dynamics models. The second focus area was to determine diesel particulate matter (DPM) concentrations in the mine. For large-opening underground stone mines, controlling DPM exposures dictates the design of the ventilation system. Therefore, researchers carried out the DPM sampling campaign to identify potential areas of concern within the mine. The samples collected during the campaign were analyzed using NIOSH Method 5040. The sampling was done using the Mine Safety and Health Administration’s (MSHA) compliance sampling methodology.

Feb 1, 2023

By Warren K. Kourt

Many important discoveries of mineral deposits have been made as a result of routine exploration for oil and gas. Through the presentation of three hypothetical case histories, including cost data, the author shows how mineral evaluation can be performed during routine petroleum drilling operations and how mining companies and oil companies or oil operators can cooperate in such endeavors.

Jan 1, 1972

By Siwiec A

The laboratory investigations which are necessary to evaluate the mineral processing effectiveness usually include density separation of narrow size fraction of the feed and one of the products. In each size - density fractions the content of valuable mineral has to be determined. These data and yield in each size - density fraction can be specified by a matrix of partition coefficients. They are counterparts of recoveries. These coefficients can be compared with the mean recoveries at each density or size fraction or the total recovery, to determine which density - size fractions are processed in the best or worst way. The basic categories are: vector of metal content l _i 1711, 7t2, òòò, ltM I ò vector of particle size distribution x = I d1, d2, ..., dN I ò matrix of partition coefficients P11, P12, Pi N P _ P21, P22, ..., P2 N PM1 PM2..., PMN These three conceptions allow one to determine all the basic metallurgical parameters of a mineral processing unit. Losses of valuable mineral are connected with: ò mineralogical composition of the ore (types of minerals, their properties, dissemination, crystallochemical affinity, type and properties of gangue minerals), ò applied technology and technical equipment (beneficiation as a stochastic process, processing methods, process control, intergrowth liberation, water quality). Examples of application of the analytical method proposed are given for zinc - lead and coal processing plants.

Jan 1, 1993

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By Fred Turin, Kim Cornelius, Lisa Steiner

NIOSH researchers have been examining underground coal mining activities in order to evaluate work crew hazards. In 1994 a continuous mining machine operator was killed by falling roof during extended cut mining. Many aspects of the incident were used by NIOSH researchers to develop a scenario interview. The goal was to provide a realistic framework for acquiring frank and detailed insights. The interview consists of two sections. The first describes the underground mining conditions. The second recounts the fatal incident. Each section is supplemented by a diagram and a set of questions addressing relevant safety issues. The interview was administered at three mines that actively take extended cuts. Researchers found the scenario approach to be an effective interview tool as well as an effective hazard awareness and safe work practices training platform.

By Augustus Locke

I WISH to urge on this Committee the task of evaluating mining geology. -My motive is as follows: It, is a. duty of the Institute from time to5 time, to establish the social perspective of the professions grouped within it, not simply to promote their use, but to determine with engineering definiteness their true powers and functions. This becomes the delegated duty, therefore, of this committee in respect to geology. Be- cause my own subject is mining, I shall confine my remarks to mining geology. But I believe that the evaluation should be made to include all of that geology termed economic. The perspective for such evaluation is shown in the nature of the public support given to geology. The federal Geological Survey, the leading organization on the economic side, is actuated by the zeal of a small group of devoted professionals who consider its work valuable, ' It proceeds, however, on a starvation ration of appropriations, and that implies that neither the corporations, the voters nor the vote getters consider it important. Altogether, in' the public consciousness, geology is negligible. That, at the same moment, .the profession should act with full confidence, while everyone else should act' with opposite motives, is not fitting. For us, as a committee, to remain incurious regarding such a disparity of beliefs is quite impossible.

Jan 1, 1931

By Jan M. Mutmansky

Since 1973 when the first edition of the SME Mining Engineering Handbook was published, many significant changes have occurred in the US mining industry. The industry went through a fairly prosperous period immediately after 1973, but then many economic pressures came to bear on mining companies, particularly in the metal and coal branches of the industry. These pressures changed both the mining methods used and the general economics of the mining methods. As a result, the industry today is different in many ways titan it was in 1973. A general summary of some of the more important changes that have come about will be provided here as well as some assessment of the effects of these changes on the choices of mining methods. In the metal mining industry, the most significant trends were increased surface mining, the use of larger and more efficient equipment, and increased technology and automation. The primary impetus for these changes was unprecedented competition from foreign producers. In many cases, this competition came about because of the nationalization of foreign mines and the tendency for these mines to become a source of foreign exchange. Under these circumstances, the mines could be operated even though they were not profitable. As a result, domestic

Jan 1, 2008

By Joseph M. Tarantino, Eric F. Perry, Keith B. C. Brady, Michael W. Smith

The Pennsylvania Department of Environmental Protection in 1998 reviewed its permitting process to determine how effective its program has been in preventing pollution and to identify here it could be improved. Of the 1,699 bituminous mine permits issued from 1987 to 1 996, 50 were identified to have current or past postmining discharges with water quality problems. The remaining 1,649 sites had no known current or past postmining discharges problems. The 50 sites were selected for further review. On closer examination, 33 of these permits no longer had water quality problems or the problem had not actually resulted from the permitted mining activity. Only 17 permits, or one percent of the total permits issued, were found to have caused long-term postmining discharges serious enough to require treatment and prevent bond release. Analysis of these 17 sites using current knowledge of mine drainage prediction, revealed that the most common cause of error was inadequate information in the permit application. Errors in interpretation of the application data and in implementing the permit were less common. A very small percentage of all permits issued resulted in postmining discharges for no clearly identifiable reason. Trends over the 10-year study period indicated a decreasing incidence of permits resulting in postmining discharges. Further, with the exception of the first few years of data, most of the postmining discharges were of mildly acidic or alkaline quality and amenable to passive treatment.

Jan 1, 2000

By Berthold Pilz

The importance of a power economy that is efficient both in technological and economic terms has been clearly recognized in recent years. In 1977 the German Federal Government therefore introduced its Energy Research and Energy Technologies Program 1977-1980, which consolidates the government activities in the field of nuclear and non-nuclear energy research. The priority objectives of this program can be summarized as follows: safeguarding the medium- to long-term energy supply in the Federal Republic of Germany at reasonable overall macroeconomic cost, taking into account the requirements of environmental protection and the safety of the population. In the field of coal mining technologies, about 200 research projects are currently under way. A total of DM 1.7 billion is earmarked for research to be conducted in this area between 1977 and 1980.

Jan 1, 1979