Search Documents

By M. Holuszko, I. Mikhalev

"Previous studies described by Galvin et al. (2017) have shown that for Australian bituminous coal fines, both in batch and in continuous process, the new improved oil agglomeration procedure based on the use of high-internal-phase (HIP) emulsions, as compared to the conventional “pure oil” agglomeration process, enables a significant reduction in the amount of oil while reaching a high yield of clean coal (approximately 90% of agglomerates greater than 355 µm in size) in a significantly shorter time. The HIP emulsion used in these experiments comprised up to 95% vol. aqueous solution of sodium chloride (3% wt. concentration) and for the rest, a mixture of kerosene (oil) and sorbitan monooleate (SMO emulsifier) in a 1:1 ratio as a binder. This study evaluates the applicability of the new HIP-oil agglomeration process to treat Canadian bituminous ultra-fine coal and Russian sub-bituminous coal fines and compares results from agglomeration to the flotation response of both coals. Oil agglomeration is known to be sensitive to surface properties of coal. Since surface properties of coals depend not only on the rank of coal but also on their origin (depositional environment) and mineralogical composition, both the applicability of this new improved agglomeration process to the non-Australian coals and its efficiency became the motivation for this study. To evaluate the applicability of the new process to both Canadian bituminous and Russian sub-bituminous coals, a series of bench-scale tests were carried out under conditions similar to those described by van Netten et al. (2016) for the Australian coals. Based on the results obtained in this research, new boundary conditions for the application of the HIP emulsion-based oil agglomeration process have been outlined and conclusions on the viability of the new process to treat ultra-fine coal from Western Canada and Russian sub-bituminous coal fines have been reached.INTRODUCTION In most cases, to meet the market requirements, the mined coal has to be processed to reduce the ash content by the removal of mineral matter and thus to increase the quality of the coal products (van Netten et al., 2016). Generally, flotation is used for processing fines from high rank coals; however, there are high losses of very fine coal due to the inefficiency of this process. Furthermore, difficulty in dewatering the fine coal results in excessive moisture levels causing coal handleability issues, which increases costs in the coal-cleaning industry (Capes & Darcovich, 1984). Much of the development that has occurred in fine coal cleaning has taken place with higher-value coal, often metallurgical (Klima et al., 2012). If the fine coal is deemed to be too difficult or expensive to process, it may be discarded as waste (van Netten et al, 2014). Such disposal not only creates an environmental liability but may also result in the loss of a valuable, high quality product that is better liberated than the coarser fractions of coal."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, N. Esmaeili, R. Hejazi, A. D. Ahmadabadi

The main challenges in most low grade iron ore deposits are finding the optimum flowsheet for beneficiation to achieve a final concentrate from both technical and economic viewpoints. Dry preconcentration techniques are being used to assist in reducing the amount of ROM feed to the plant. In this paper the benefits of utilising a dry cobbing magnetic separation technique for upgrading the product of HPGR in a closed circuit with dry screen 4 and 1.4 mm by performing a pilot scale test work was investigated. The experimental test work was done on two sample types of Yogi BIF magnetite iron ore located in Western Australia. Prior to magnetic separation studies, detailed characterisation of the feed materials including physical, chemical, mineralogical and magnetic properties were carried out. Furthermore, the effects of process parameters: drum rotation speed (1.5, 2.5 and 3.5 m/s), magnetic field intensity (1100 and 3800 gauss) and feed size (minus 4 and 1.4 mm) were investigated. The results revealed that sample type1 with 33.90% Fe could be upgraded to 41.51% Fe by using a stage of 1100 gauss dry magnetic separator with 69.12% weight recovery and 84.36% Fe recovery at a size of 4 mm. Also for sample type2, it is possible to increase Fe grade from 29.84% to above 36.68% with 75.58% weight recovery and 90.32% Fe recovery by applying one stage of 1100 gauss dry magnetic separator to a 4 mm size sample. Keywords: Banded iron formation (BIF), pre-concentration, dry cobbing technique, magnetic separator

Jan 1, 2020

By B Madeja-Struminska

The method of evaluation of the approximate temperature of arising spontaneous fire centre and time of coal self-ignition is presented in this paper. The method uses BystronÆs (1997) model of coal self-heating and measurement of carbon monoxide concentration in the mine air outside the fire centre. Knowledge of the spontaneous fire centre temperature and time of fire beginning allows for more accurate analysis of the fire hazard in the coal mine and allows for adequate time to undertake special fire prevention actions. The method is illustrated by an example from Polish mining practice.

Jan 1, 2005

By Alain Tshilombo, Vijay Reddy, Chowdary Meenavilli, Kelvin Buban, Cory Kosinski, Sriraj Meenavilli, Siddhartha Tirumalaraju

The use of artificial intelligence (AI) for process optimization is expected to play an increasingly important role in the future of the mining industry. The objective of AI is to develop a data driven soft (virtual) sensor using historical data that can estimate unmeasurable characteristics of the process and provide appropriate recommendations during operation to optimize the process through continuous learning. The application of AI to a hydrometallurgical process was evaluated by Sherritt Technologies in coordination with NTWIST. Historical operating data obtained from the Ambatovy facility’s High Pressure Acid Leach (HPAL) circuit was used to develop models to predict autoclave discharge parameters based on operating conditions and ore mineralogy. The prediction models were developed in such a way to also allow the user to simulate and test different operating conditions. A second set of models (AI model) were developed based on the prediction models, economic data and operating constraints for a given process unit to identify optimal reagent and steam dosages across the HPAL circuit. The development of these models was significantly complex due to the dynamic and interactive nature of the HPAL process. Despite the complexity of the models, the models were able to predict, with accuracy, the relationship between ore composition, leach autoclaves retention time, acid addition and steam addition with metal extractions as well as levels of impurities in the autoclave discharge slurry. The study showed that AI has the potential to improve the overall operation of a facility through providing tools to assist with training, troubleshooting and process optimization. INTRODUCTION The Ambatovy project, located in Madagascar, is one of the world’s largest nickel and cobalt mining and processing operation, with a design capacity of 60.000 tonnes of nickel and 5,600 tonnes of cobalt per year (Collins et al., 2016). Commissioning and start-up of the Ambatovy mine and plant facilities were completed in 2012, with acid first introduced to the ore leach in March 2012. Commercial production (defined as 70% of design capacity) was achieved in January 2014 and the production level required to achieve financial completion (90% of design capacity for 90 days) was achieved in March 2015 (Valle et al., 2016). Figure 1 shows a simplified flowsheet of the hydrometallurgical pressure acid leach (PAL) process employed by Ambatovy.

Jan 1, 2019

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By H. K. Conn

This paper discusses briefly the evaluation of chrysotile asbestos deposits in ultramafic rocks. Such deposits are limited to serpentinized peridotite and/or dunites. The purpose of any evaluation is to determine whether a deposit contains sufficient ore mineral to justify profitable exploitation. Dimensions of a mineral zone are established by conventional methods, such as mapping, ground magnetic surveys, diamond drilling or underground exploration. The value of the contained asbestos fibre Is dependent on numerous physical properties such as fibre length, strength, flexibility, as well as the actual amount of fibre present. The determination of grade is difficult. The Quebec Standard Test (Q.S.T.) is used to grade fibre according to the proportionate lengths of fibre present. A method of visual vein counting allows calculation of an approximate percent fibre together with a simulated Q.S.T. Various drilling methods are discussed, diamond drilling is favored. Bulk sampling is required to determine fibre quality. Correlation of visual techniques and laboratory methods are often difficult. Reasons for any variance are discussed. Underground bulk sampling of most potential ore zones is strongly recommended to confirm the viability of the property. Evaluation of slip fibre deposits requires greater reliance on laboratory testing as visual methods are difficult to apply. Cross fibre has greater inherent strength.

Jan 1, 1971

By Neha Shukla, Nikhil Dhawan

The current study examines the extraction of rare-earth elements from trichromatic phosphor of discarded tube lights via baking processes. The Y2O3: Eu3+ (YOX) and BaMgAl10O17: Eu2+ (BAM) phases completely decomposed during acid and alkali baking with > 90% Eu and Y extraction. Prior, selective acid leaching of the YOX phase enhanced the acid baking process at a lower temperature (< 230 ℃). Feed acid baking showed a maximum 87% Tb, 36% La, and 17% Ce extraction at 500 °C, 0.5 h, 1 ml/g H2SO4, and alkali baking yielded 16.1% Tb, 86% La, and 73% Ce at 300 ℃, 0.5 h, 50 wt.% NaOH. The acid baking of the acid-leached phosphor yielded 72% Tb, 95% La, 63% Ce, ~ 95% Y, and Eu extraction at 300 °C, 0.5 h, 1.05 mL/g H2SO4. Lower Tb extraction during the acid baking of acid-leached phosphor can be attributed to the formation of Ba3Tb( PO4)3 and BaTbO3 phases. Insoluble Si3Tb5 phase formation and partial decomposition of CeMgAl11O19: Tb3+ (CMAT) phase in the alkali baking route leads to lower Tb extraction. The acid baking process is suitable for extracting Tb, Eu, and Y, whereas the alkali baking process is suitable for La and Ce. The thermal analysis of phosphor and flux interaction depicts that alkali baking is less energy-intensive than acid baking. In comparison, the one-step acid baking process and the two-step alkali baking process yielded desirable extraction results (87% Tb, total RE (rare earth) 78.5% and 50.4% Tb, total RE 59.3%). The product yield in the acid and alkali baking route of feed, acid-leach phosphor is 36%, 29%, and 39%, 28.2%, respectively, with ~ 98% mixed rare-earth oxide purity.

May 5, 2022

By William G. Freeman

In comparison to many mineral commodities, barite has a low unit value. It is mined and sold in low volumes in high-grade (90-98% BaSO4) forms to basically one industry that uses approximately 75% of the free world production. Based upon the above criteria, all factors must be considered in determining if a barite deposit is economical; such as, the type of deposit, mining and milling methods required, transportation to the markets, tariffs, local political conditions, etc. In other words, barite mines are made--not found. The length of this paper precludes any indepth discussion of geology, mining and metallurgy of barite. Most of this information can be found in data already published, such as D. A. Brobst&apos;s bulletin1 on the Barite Resources of the United States.

Jan 1, 1971

By K. G. Black, B. P. Faulkner

Laboratory batch flotation rests are used for comparison of the floatability of ores and for comparison of the effect of various treatments on ore floatability. Although it is difficult to predict exact recoveries for continuous flotation on the basis of batch tests, considerable quantitative information can be obtained through their use. A simple method is presented which provides a convenient means of quantitatively evaluating results from laboratory batch tests. The information obtained is in the form of a discrete flotation rate distribution, which, if desired, can be used directly in a simulation of continuous flotation. Equation of Batch Flotation The validity for batch flotation of the first-order kinetic equation is accepted: [ ] where k is flotation rate of a class of articles and W (t) is weight of particles of the class in cell at time t. Thus, at time t, the fraction of the original amount of the class of particles still remaining in the cell is [ ] where W (0) is weight of class of particles in cell at time zero. If there are several classes of particles in the cell, each with its own flotation rate, k4, the fraction of the particles remaining is [ ] where W (t) is now the total weight of n classes, a, being the original fraction of W (0) belonging to the ith class. Accordingly, [ ] [Fig. 1] shows the result of a typical batch test. Such result can be characterized by a set of particle classes, each set described by a flotation rate, [ki,] and a corresponding fractional magnitude, [ai.] [ ] Multiple Regression Equation Eqs. 3 and 4 may be combined to give

Jan 1, 1973

By Askari-Nasab, D. Checkel, K. Awuah-Offei

Life Cycle Assessment (LCA) is an emerging environmental management tool for examining environmental impacts from cradle to grave. In this paper, LCA is used to evaluate the acidification potential (AP) and global warming potential (GWP) of belt conveyors and truck haulage systems in a surface gold mine using the ISO 14040 standards. The results show that, for AP, the truck system has 32 kg of equivalent SO2 per functional unit, compared to 8 kg for the conveyor system. However, for GWP, the conveyor has 2,820 kg of equivalent CO2 per functional unit, compared to 648 kg for the truck option.

Jan 1, 2009

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By Jack S. Greber

The mining industry generates an estimated 2.3 billion tons of solid waste each year and the total accumulated mineral resource solid waste at both active and inactive mine sites, approaches 30 billion tons. Five industries generate 85 percent of mine solid waste: copper, phosphate, iron, uranium, and coal. Over the past several years, the Federal government has shown increasing interest in the proper disposal of solid wastes generated by the mining industry. Three new pieces of federal legislation have been passed recently beginning with the most comprehensive regulatory authorization passed in 1976, the Resource Conservation and Recovery Act (RCRA) which has been amended to the Solid Waste Disposal Act Amendments of 1980. RCRA is implemented and enforced by the Environmental Protection Agency (EPA) and intended to control municipal and industrial solid wastes. Next came the passage of the Surface Mining Control and Reclamation Act (SMCRA) of 1977 which is implemented and enforced by the Department of Interior to control coal surface mining and the surface effects of underground coal mining, and finally, the recent Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 implemented by EPA and enforced by the Nuclear Regulatory Commission (NRC) to control uranium mill tailings disposal.

Jan 1, 1981

By Hung Tran, Denis Fleury, (Ken) Qian Liu

Pastefill technology has gained an increasing popularity over the past decade. The main advantages are: environmental performance (mainly in tailings disposal), low operation costs and ease of operation, as well as homogeneous properties. However, its weaker nature compared to other types of fill makes it more vulnerable to blast damage. In the last few years, Louvicourt Mine has experienced some cases of pastefill sloughage during the mining of secondary stopes. In order to reduce pastefill sloughage, some studies have been undertaken to investigate the causes and to find possible solutions by looking at stope design, extraction sequence, ground support and blast design. This paper presents the results of a blast damage study carried out at Louvicourt on the 860m level. The instrumentation included vibration monitors (using 6 sets of triaxial geophones grouted in the pastefill), a borehole camera to observe the damage in the pastefill, and a cavity monitoring system for three-dimensional surveys of the blasted stope. The test stope was mined out by four slot blasts and three mass blasts. Most of the damage was created by the mass blasts. It was found that the accumulation of ground vibration was mainly due to the low seismic velocities in the pastefill and the relatively tight delay between blastholes. In addition, there was a substantial difference between the critical PPV in the confined and unconfined pastefill. In practice, these findings have led to modifications of blast design to minimise the exposure time of pastefill walls to air. Such modifications included changes of blast sequence in secondary stopes and delay layout between heavily loaded blastholes. Over the paste two years, the implementation of new blast sequence has shown encouraging results in terms of reduced pastefill sloughage and dilution.

Jan 1, 2000

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

Graded macadam slag base has been used successfully by the Department of Main Roads, N.S.W., in the construction of Expressways. However, the use of graded macadam in urban conditions introduces problems which can be avoided by the use of material meeting the specification outlined in M.R. Form 744. This paper outlines the rationale behind the technical requirements of the specification for the "Supply of natural gravel or crushed rock for road pavement (bitumen surfaced) M.R. Form 744". A blend of materials produced from slag is proposed as a potential solution for the production of slag base which would be suitable for use in urban construction or maintenance of roads.

Jan 1, 1979

By H. Bilgin, Sedat Esen

In this paper, the ground vibrations induced by blasting for stripping work at Sekkoy Open Cast Coal Mine belonging to TKI Yenikoy Lignite Mine (YLI) are investigated and the procedures for monitoring and control of ground vibrations are presented. Ground vibration measurements are conducted in the direction of Turkish Electricity Authorities’ Yenikoy Establishment and social facilities because of the complaints and annoyance arising from this site. Forty ground vibration records are taken in this direction and the vibrations are measured in transverse, vertical, longitudinal components together with peak vector sum. After then the scaled distance relationship is determined at 95% confidence value. Further, Fast Fourier Transform analyses are carried out to determine dominant frequencies for both ground and the structures and amplification factors. When the records taken at four different structures together with the ground are evaluated, it is observed that one of the apartment buildings is amplified the amplitude of longitudinal component 4.3 times. The maximum allowable amount of explosive that can be fired safely at this mine is calculated and recommended on. In the determination of safe amount, 95% confidence line, USBM RI8507 and OSMRE criteria, the dominant frequencies of both ground and the structure, amplification factor and the human response are taken into account.

Jan 1, 2001

By K. H. Singh

The addition of new data and corrections can be made under the control of a simple editing session. All programs for this system are written in FORTRAN and executabe "MACROS".. After the addition of new data, the whole file Is reinitialized to update the binary file and cross-reference tables. Updating the binary file involves rerunning the initializing program. The creation of graphic plots like cross sections and plan views is menu-driven from a terminal and very user-friendly. Small files containing not more than 10,000 entries (survey and assay points) are suitable for this setup, particularly for computers with less than 2 Megabytes of real and virtual memory. The largest file processed contained 35,000 lines of survey and assay information and required 4 megabytes of virtual memory. Working with this size file slows down the time for the creation of plots and cross sections. Another independent system is more akin to a financial type of data base. It was installed in one Anaconda mine as part of the operation&apos;s inventory, warehouse, day-pay payroll, and purchasing data bases. It is a highly hardware-dependent system, in particular, IBM&apos;s CICS/VS (Customer Information Control System/Virtual Storage). This is a true relational data base that optimizes storage requirements, supports online inquiry, update, data entry, and data security. While this system has been tested and proven in accounting applications, it requires programming expertice in PL/I and other CICS utility programs. It is well suited for huge data bases (like the 35,000 lines of data), but cumbersome for small engineering files.

Jan 1, 1985

By K. Perry, R. Eades

"Highwall miners continue to be implemented by operations to increase recovery, improve margins, and justify higher stripping ratios as high quality surface reserves become increasingly rare. Many times, operations facilitate projected underground operations by leaving an intact highwall for development purposes. These facts result in larger highwalls that are left standing for increased periods of time prior to reclamation. As a consequence, worker exposure and risk is also elevated, resulting in higher potential for accidents or fatalities relating to surface highwalls. Highwall stability is a complex issue, dependent on both geologic and mining factors. Dynamic numerical modeling offers the capability to assess possible stability issues related to blasting-induced ground vibrations. Research has been conducted to evaluate the effect of highwall stability due to ground vibrations from blasting events. Additionally, the relationship of amplitude and frequency, and their impact on highwall stability is investigated. The results of this modeling indicate that amplitude has little impact on stability. However, frequency has a significant impact on highwall stability. INTRODUCTION The number of mining fatalities has declined since 2010, and 2016 is currently on pace to continue this trend (MSHA 2016). This decline can be directly correlated to the decline in surface mining activity and the overall decline of the coal industry. However, since 2002 the percentage of surface coal mine fatalities associated with highwall activities remains relatively high, constituting approximately 15% of all surface mine fatalities. 2014 was the first year with a highwall failure fatality since 2011. Most recent surface coal mining fatalities are associated with machinery and haulage. Table 1 provides a summary of the total surface coal mining fatalities, and the number of highwall failure fatalities dating back to 2010.Highwall stability is a complex issue, dependent upon geology and geologic discontinuities within the rock mass, along with highwall geometry, standing time, and applied stresses. Another possible concern that has not been previously investigated is the effect of blasting-induced stresses on highwall stability and the stability of web/barrier pillar systems as a result of ground vibrations from blasting events. Many modern surface coal mines employ numerous extraction fronts that rely on blasting for primary rock breakage. This results in highwall and highwall pillar systems experiencing blasting-induced stresses of many different types and magnitudes."

Jan 1, 2017

By F. Schott, M. James, G. May, E. Baker, C. Johnson, R. Bauer

Explosive demolition typically utilizes cutting charges to sever columns, detonating cord to time charges and provide an initiation path, and dynamite as a kicker charge. The kicker charges of dynamite are used to “move” columns out of alignment, causing collapse. Demolition projects involving dynamite can pose significant health and safety risks to workers and the public. Nitroglycerin in dynamite can cause dizziness, fainting, and other health problems. Moreover, dynamite placed directly on columns can result in fragmentation and cutoffs, preventing other charges from being initiated and resulting in incomplete demolition. Fragmentation can occur from columns and travel significant distances from the initiation point, sometimes reaching hundreds of meters away. This fragmentation can pose serious dangers to anyone in the vicinity, including workers and members of the public, as the debris can cause severe injuries and property damage. The force and velocity of the fragmented material can be unpredictable and difficult to control, making it important to take proper safety precautions and consider alternative demolition methods that minimize the risk of fragmentation. Previous work concluded that casing charges in water showed that a reduced dynamite charge mass could still successfully kick the charge out of alignment. This study aims to investigate the use of Pentolite boosters in water-cased charges as a safer alternative to dynamite-based demolition. The research involved testing various amounts of dynamite and pentolite boosters in water to compare their effectiveness in moving a hanging W-beam, which swung freely like a ballistic pendulum. Water-cased charges consistently move the column at a higher velocity than the traditional dynamite charge placed directly on the column. The method of water-casing increased the area of impact and impulse felt by the column, improving demolition efficiency when compared to traditional demolition methods as found in previous studies. Pentolite water-cased charges moved the column at 7.8 meters/second (m/s) while the dynamite water charge moved the column at 5.9 m/s. The increased strength and explosive properties of the pentolite contributed to this increase in velocity. This study showed that it is feasible to remove dynamite from demolition projects by utilizing pentolite boosters and that when considering safety, explosive properties, and effectiveness, pentolite boosters can be cost effective as well.

Jan 1, 2024

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905