Search Documents

By W. D. Watson

"Early in mine development at Quintette Coal Limited major problems were encountered with the fleets of primary equipment which seriously hampered production. These major fleets (cable shovels, hydraulic shovels, hydraulic drills and electric trucks) have consequently been the focal point of maintenance efforts. Some were prototypes in the Canadian mining scene and brought with them new concerns to test their skills. The problems were studied and the category and areas which were having the greatest impact on the reliability of the equipment were determined. Once defined, priorities were established and a program was initiated which was designed to accomplish a resolution. Resulting from implementation of this systematic approach, over the past three and one-half years, the fleets are now giving good reliability and industry standard availabilities. Along with these significant achievements, cost per operating hour on some of the equipment fleets has decreased substantially and continue a downtrend through 1987. This paper identifies the problems and describes the resolutions. IntroductionIn the early years of the mine development, Quintette Coal Limited (QCL) experienced production shortfalls due to problems with the major excavator and haulage fleets. A large fleet of hydraulic excavators had been purchased, and QCL was among the first northern users of all hydraulic blasthole drills. They were also using some prototype equipment and encountered problems which were not common on other types of equipment or were unknown.Because of these unique problems and lack of experience from other mines to draw on, an analytical approach was taken to areas and associated causes of the delays affecting the availability and reliability of equipment. This was done by dividing the equipment downtime into seven classifications of delays, i.e. maintenance, electrical, hydraulic, mechanical, damage, service and preventative maintenance, and tires; and then each was expressed as a percentage of total downtime. Subsequently each of the delay classification was divided into categories e.g. electrical to six categories - wheel motors, main alternator, relays, cards, no propel, lighting and 24 V system. Then, the basis for further study had been established.From this preliminary analysis of historic records, it was possible to determine the areas which were causing the majority of the downtime. These areas were then analyzed to evaluate causes and to determine possible solutions to the problem s. This paper addresses the major fleets, their problems and eventual solutions. Plea se bear in mind that the over-all objectives were to increase physical availability and reliability."

Jan 1, 1988

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

By N. Vayenas

Modern mines possess a wide variety of capital intensive equipment. Equipment failures and the associated down time contribute significantly to the overall maintenance, operating and production costs of a mine. Reliability investigations are becoming a standard practice, as the equipment becomes more complicated and the effective use of resources is critical for achieving higher productivity and mine safety. In view of the recent global initiative for sustainable development in the mineral industries, reliability of capital intensive machinery should be considered as a key indicator for sustainable development and growth. This paper discusses the application of equipment reliability as a sustainability indicator and proposes a methodology for its practical use. Reliability of equipment systems is useful for product life cycle assessment, mine performance measurement and evaluation.

Jan 1, 2007

By J. J. Sense

10.2-1. Equipment Scheduling. In any earth-moving operation, more profit may be earned or lost by equipment scheduling than by any other single facet of the project. Many now-defunct earth movers would have survived the cost-profit squeeze had they followed an efficient, cost saving, equipment scheduling program. The ideal program would have every item of the equipment fleet working all of the time. In practice for many obvious reasons, principally mechanical conditions, operating conditions, and human nature-this ideal situation is not possible. The cost-conscious organization strives to keep as many pieces of equipment of the fleet working efficiently as much of the work day as possible. Operating efficiency requires the minimum equipment to move the predetermined tonnages in the prescribed period of time. In the case of a shovel-truck operation this would mean the scheduling of the minimum shovel and truck shifts to excavate and transport the necessary tonnage to the processing plant or waste dump. To accomplish this goal, the operator must work from the predetermined production established by the requirements of the plant, stripping ratio, mine plan, etc. This production schedule may be in terms of tons or yards per year, per month, or per hour, but must eventually be translated into tons or yards per ma- chine per unit of time. In this regard, the reader is referred to Sections 8.0, Excavation and Loading, and 9.0, Haulage and Transportation. The trend to larger and faster, and as a result more costly, equipment requires that the operator consider every possibility to keep the equipment operating around the clock, seven days per week. In some areas seven day operation may not be feasible economically, because of premium pay for Sunday work. Mine labor agreements are generally written without premium pay penalties for weekend work, and such scheduling is possible and most often desirable.

Jan 1, 1968

The selection of the mining fleet can have as much of an effect on the efficiency and effectiveness of an operation as the mining method. This is not to say that inefficiencies are only attributable to inappropriate equipment selections, these aspects have many factors but are not the subject of this paper.This paper will give an overview of equipment selection processes that have been utilised to date. It will also look at the increase in application of study programs/simulations from an aspect of accuracy, as well as the importance of enabling the analysis of multiple sensitivity scenario planning. An aspect that is increasingly important in project planning with commodity market movements.Another aspect that is increasing in popularity is that of automation, what effect does this have on equipment selection? What additional aspects need to be taken into consideration when assessing Automation of equipment from the beginning of a project as well as introduction into an operating mine?Once the selection process has been finalised and equipment implemented, how do we, as an industry, 'close the loop' through analysis of estimated versus actual equipment application?

Dec 6, 2010

By Jean-Michel Rendu

Equipment capital operating costs represent a significant portion of the total cost of most mining operations, and a variety of computerized methods have been developed to assist in the selection and effective use of this equipment. The questions to be answered and the tools available to answer these questions vary with the type of mine to be analyzed, the stage of development of the mining venture, the size of the operation, the details required, and the technical or economic objectives to be reached. Even though a majority of publications are directed towards open pit mining operations, the underground environment is not neglected. In the early planning stages of a mining venture, equipment selection is the problem to be solved. The simplest computer systems are designed to' automate time consuming manual tasks. A data base is supplied to and maintained by the user, which describes the technical and economic characteristics of available equipment. The user specifies the physical environment within which the equipment will be used and chooses from the data base a combination of loading and transport equipment. The role of the computer is to detemine the production which will be likely reached, the associated costs, and other relevant statistics. This approach is most helpful when modeling small operations or isolated parts of larger operations.

Jan 1, 1989

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By Max B. Holfeltz

[Many factors impact the selection of one mining method over another for deep seated, thick seam coat deposits. Generally if an operating mine is recovering coal at high volumes from thick seams then a truck/shovel fleet is required for coal loading. The next consideration is how to remove the associated burden. If an operation has relatively small amounts of burden associated with the coal then a truck/shovel fleet may be employed for burden removal simply to standardized the entire mine equipment concept. On the other hand large amounts of burden associated with the coal can justify employment of draglines for burden removal. Specific economic, productive, and physical factors contribute to the final decision.]

Jan 1, 1983

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By H. Aykul

The choice of which mining method to use at many large surface coal mines is often dicated by what machinery is available or what experience the mine management can offer. One of the most significant surface coal mines in Turkey is owned and operated by the Turkish National Coal Board, located to the west of the city of Kütahya. The Seyitömer Lignite Enterprise (SLE) extracts low quality coal, the majority of which is supplied to an adjacent power station. The coal seems at SLE contain bands of ash which under normal mining conditions are extracted with the coal. This increases the ash content of the run of mine coal and results in lower efficiency at the power station and financial penalties for SLE. In this paper, therefore, selection of the best possible equipment and production method was identified to achieve high selective mining at SLE. The research found that two different high selective mining methods were suitable for selective excavation of the B3 seam, which were hydraulic excavator and truck and surface miner and truck combinations. It was also found that high selective excavation could provide the desired coal quality at 52% lower costs when the whole process (excavation, transportation, processing, etc.) was considered. Keywords: coal mining, surface mining, selective mining.

Jan 1, 2007

By Hare G

The emphasis in Australia, until recently, has been on large scale mining methods with drive sizes in excess of 4.5 metres square and the acceptance of high dilution ratios, even when working in relatively narrow orebodies. The rising cost of extracting and treating the recovered ore and the lower prices available in the world markets has seen a growing trend to narrow mining methods.Traditionally narrow orebody mining has been carried out using hand held drilling methods and rail mounted boggers. Recent advances in mobile equipment now offers the operator of narrow method mines the opportunity to completely mechanise the mine from the drilling, through bogging to haulage, while maintaining minimal dilution in drive sizes to two metres wide or less.

Jan 1, 1993

By Wright G. N

Curragh Queensland Mining Limited, a co-venture of Australian and overseas interests, operates an open cut coal mine 13 km north of the township of Blackwater in Central Queensland, refer attached location map.

Jan 1, 1992

By Matthew J. Hrebar

Dragline stripping operations account for over one-half of the U.S. bituminous coal production mined by surface coal mining methods. The dragline is a popular stripping tool because of its flexibility in varying overburden depths and relatively low operating costs per cubic yard of overburden. Because of the relatively high capital costs of the machines and their use as a primary stripping tool, the selection process is an important step in the mine planning procedure.

Jan 1, 1979

By I KylmSkorpi, H Mansikkaviita

The traditional direct-heated drying process has been replaced by the steam drying process in non-ferrous metal smelters, where steam is available from waste heat boilers. Many recent projects have selected Kumera Steam Dryers in equipping a new production line or modifying an old production line. The industrial performance of the steam dryers has shown significant energy saving and emission reduction. The steam dryers have been operated at high availability and long maintenance interval. As the process principle of Kumera Steam Dryer is different from other equipment, the set-up for steam dryer plants is configured to fit the smelter site and operation conditions to achieve optimal performance. This article discusses the equipment involved in the steam drying process and their combination options.

Jan 1, 2008

By M. Lotfi

The criteria for evaluating equipment operator performance were identified as the changes in reaction time, the changes in physiological responses, and the changes in subjective reporting of stress. Data were collected while the Subjects operated a front-end loader simulator. This report out-lines the components and the tasks generated by the simulator. It explains the simple and basic assumptions underlying the design of the simulator and the methods of data collection. Improvements that can facilitate the collection of data, including the connection of the simulator to a portable personal computer for on site use are discussed. Statistical analysis of data showed significant deterioration in performance. The report concludes that operator performance can be measured and improved. This report shows that the operator tasks can be simulated by means of simple simulators, the complexity of which is determined by the availability of funds and the area of interest of the investigator.

Jan 1, 1989

By James J. Scott

INTRODUCTION This paper presents the basic principles which must be followed to create a truly inherently safe mining system. The need to relate the support mechanism to be employed to the ground reaction curve and basic rock mechanics principles will be pointed out. The support system must function in concert with the deformations that are inherent in the selected mining system. Following the support selection, the mechanics for installing support must be developed. This is best done through a cooperative effort between mine engineers, mine operators, safety personnel, equipment sup- pliers, and government inspectors both state and federal. Accident statistics, near miss statistics, review of equipment used by others, geologic features, etc. will necessarily have to be studied. The goal of equipment development and selection should be to develop inherent safety by removing the miner from the hazard area or by providing absolute protection for the miner if he must work in close proximity to the potential fall of ground. The role of good productivity in reducing the numbers of men exposed to hazards is emphasized as a good safety measure ROCK MECHANICS PRINCIPLES A thorough understanding of the ground reaction curve surrounding openings to be created is essential in the

Jan 1, 1982

By Christopher J. Bise

The potential of the coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints which have tended to limit the development of these reserves which can only be deep-mined are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short- term the industry has to incorporate presently available equipment which were not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment that are in use today and their possible application to thick-seam mining. The paper also addresses the various ground control and safety considerations that are unique to thick-seam extraction.

Jan 1, 1981

By R. V. Ramani, C. J. Bise

The potential of deep-mineable coal reserves in the western United States for meeting future energy needs has been recognized for quite some time. However, two of the major constraints tending to limit the development of these underground reserves are the great thicknesses of the coal seams encountered and their high pitch. Although new mining methods may need to be developed to recover these reserves, at least in the short-term the industry has to incorporate presently available equipment not originally designed for thick-seam mining. The purpose of this paper is to present an analysis of the various equipment in use today and their possible application to thick-seam mining. The paper also addresses various ground control and safety considerations unique to thick-seam extraction.

Jan 1, 1984

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By Ismael Marquez

El presente texto describe la tecnología realizada en los equipos utilizados (pala, draga, camión, perforadora) en la minería peruana de cielo abierto. Respecto al diseño de perforadoras se debe considerar tres criterios: fáciles de transportar y manejar, poder y velocidad en la perforación para la producción requerida y el fácil acceso a sus componentes para darle mantenimiento. En el caso de las palas se considera: el uso de aleaciones en componentes críticos para mantener una relación de potencia estable, el uso de común de ciertos elementos para reducir el inventario de partes de repuesto, la instalación de sistemas automáticos de lubricación en áreas críticas, el uso de sistemas hidráulicos para facilitar la operación y mantenimiento y el uso de componentes eléctricos modulares para reducir el tiempo muerto debido a reparaciones. Finalmente, en el análisis del uso de energía o hidráulica (draga, camión) debe incluir los siguientes criterios: se debe permitir al operador el control absoluto sobre la máquina, asegurar la calidad y confiabilidad de los componentes y determinar el sistema de los más bajos costos de operación y mantenimiento.

May 1, 1980