Search Documents

By Don Kay

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By Carter J. P

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By C Zhang, I Canbulat, S Saydam, H Yu, H Chen

Natural rocks are frequently exposed to groundwater and complex geological conditions. Environments with water presence are more susceptible to chemical corrosion, which notably affects rock’s micro properties. Generally, the pH of acid mine drainage in hard rock mines can be low to 5, and the pH of quarrying waste deposits can be below 3. With the expanding scope of mining engineering in aquifers and salty areas, chemical corrosion can also caused by different types and concentrations of anions. The anions can significantly affect rock’s mechanical properties. Therefore, it is critical to emphasise the impact of anion and acid on the mechanical and micro characteristics of rock. This paper commences with an introduction to representative corrosive environments. Then the UCS tests are conducted on granite samples corroded by chloride ions and sulfate ions. Anion has negative effects on the strength of granite. The reason is that certain minerals can react and be dissolved by anions and hydrogen ions, such as Al2O3. Furthermore, the scanning electron microscope (SEM) shows that the roughness of the fracture surface increases with the anion concentration. The effect of acid is notably more pronounced than anion on the micro properties of granite. The initiated fissures and pores also increase with the concentration of SO42- and Cl- ions, which is the micro explanation for the impact of anion on rock strength and stability. Subsequently, the permeability of the granite specimens is tested. The reason that granite performs insensitivity to acid and anion is attributed to its low permeability and high content of inactive oxides, such as quartz. To summarise, anionic and acidic conditions can slightly deteriorate the mechanical and micro properties of granite. While SO42- demonstrates a higher level of corrosiveness on granite than Cl-.

Sep 1, 2024

By M. Sadegh Safarzadeh, Erich U. Petersen, Jan D. Miller

"An acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2•4H2O, PbSO4 and Cu0.47Fe0.53SO4•H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 hours with a sulfuric acid-toconcentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different concentrations. The purpose of this paper is to present our examination of the effects of sulfuric acid dosage on the extractions of Cu, Fe, and As from an enargite concentrate. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.IntroductionThe occurrence of enargite (Cu3AsS4) in copper ores and concentrates and the associated high arsenic values in such resources have resulted in a considerable decrease in the demand for such concentrates because they cannot be economically processed using conventional technologies such as smelting and atmospheric leaching (Mihajlovic et al., 2011). The exploitation of such problematic deposits through competitive treatment strategies will be required in the near future in order to satisfy increasing pressure from the copper market. It is expected that the average arsenic grade of copper concentrates will increase from 0.17% in 2008 to 0.22% by 2020 (Mayhew et al., 2011).The acid bake-leach process was identified and selected for further investigation at the University of Utah as a possible process alternative for the treatment of enargite concentrates. In this case, adequate amounts of concentrated sulfuric acid are mixed with the concentrate and heated to the temperature range 150-300°C. Subsequently, the baked material is leached with water/weak acid and the acid bake-leach process has some advantages over conventional sulfuric acid leaching (Prater et al., 1970). During water leaching, metal sulfates are released in solution, after which they can be extracted through well-known hydrometallurgical techniques. While the majority of the work has been done on oxide minerals, there is a limited record of sulfuric acid baking of sulfides."

Jan 1, 2015

This paper describes basic parameters, such as surface forces and film elasticity, affecting the stability of foams (two-phase froths). We used the thin film pressure balance (TFPB) technique to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG). The results were compared with the foam stabilities measured experimentally and the film elasticities calculated using a new model developed by Wang and Yoon (2006). It was found that at low electrolyte (NaCI) concentrations foam stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother type and concentration. Further, the kinetics of film thinning was studied at a high electrolyte concentration. The results obtained in the present work showed that the major role of a frother is to decrease the hydrophobic force rather than to increase the film elasticity. This conclusion is drawn from the observation that at the typical frother (MIBC) concentrations employed in flotation, frother additions cause sharp decreases in hydrophobic force while causing relatively little changes in film elasticity.

Jan 1, 2006

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By Michael K. Phang, Thomas A. Simpson

Field studies at an underground mine site were conducted to evaluate and monitor blast-induced vibrations on an underground coal mine roof. The vibration data were evaluated so that a suitable damage criteria or guidelines from which a safe operating distance between surface blasting and underground mine operations can be established.

Jan 1, 1984

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

This paper describes the scientific data acquisition, data interpretation, and sophisticated 3-dimensional modeling processes of an ongoing gas well stability research program by the National Institute for Occupational Safety and Health (NIOSH). Results from the NIOSH field instrumentation programs and the parallel 3-dimensional numerical modeling programs indicate that overburden depth, overburden geology, surface topographic relief, strata dip of the coal measure rocks, and casing cementing alternatives are the dominant factors affecting longwall-induced subsurface deformations and gas well casing stresses. Topographic relief could produce localized longwall-induced deformations if weak-to-strong rock interfaces are present near the bottom of stream valleys. Strata dip has significant impact on longwall-induced subsurface deformations. Cementing alternatives are found to have significant impacts on longwall-induced deformations and gas well casing stresses.

By Serhat Özdemir, Derya Öz Aksoy, Pınar Aytar Çelik, Ahmet Çabuk, Sabiha Koca, Hüseyin Koca

In carbonate flotation, oleate has been used for many years as a collector in industrial scale. Compared to sulfide minerals, the flotation of carbonate minerals requires more collector consumption and has lower yield and selectivity. It has been previously shown that surfactin provides higher yields in smaller amounts than oleate in the bioflotation of calcite as one of the carbonate minerals. In this study, the usability of surfactin as a flotation collector for magnesite was investigated. For this purpose, the adsorption of surfactin on the magnesite surface was inspected with analyses such as FTIR, SEM–EDS, contact angle, and zeta potential measurements. In addition, the effect of surfactin on the surface tension of water was also revealed. The same analyses were also performed for oleate as a reference point. All flotation experiments were performed without optimizing with both collectors. FTIR results showed that the surfactin, like oleate, was chemically adsorbed on the magnesite surface. Surface tension analyses showed that the surface tension of water decreased to approximately 32 N m− 1 at 10− 4 M oleate concentration, and this value decreased to below 25 N m− 1 at the same surfactin concentration. According to contact angle measurement results, the contact angle of magnesite was 85° after the surfactin adsorption of 2 × 10− 4 M concentration, while this value remained at 46° for oleate. Finally, according to flotation experiments, high temperatures and high collector dosages are necessary for acceptable flotation recovery with oleate, yet surfactin can produce the desired result at ambient temperatures and lower collector amounts.

Dec 13, 2022

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey’s test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By Sutham Niyomwas

The Fe-TiC composite powder was synthesized in situ by carbothermal reduction of ilmenite. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of the reaction temperature (1300 °C - 1500°C) and milling time of precursors on the Fe-TiC conversion and powder morphologies were investigated using XRD and SEM method. The synthesized products showed that composite with iron matrix and titanium carbide as a reinforced phase was formed.

Jan 1, 2006

By R. Floyd Farris

A THOROUGH knowledge of the behavior of cement slurries under elevated tempera-tures and pressures is necessary in order to solve properly the many problems pre-sented in deep-well cementing operations. In the earlier days of the petroleum indus-try the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being given, for the present, to details of tech-nique and equipment for oil-field use. More specifically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries.

Jan 1, 1940

By Guilherme Corrêa Soares

The effects of temperature and strain rate on the mechanical behavior of a superelastic NiTi wire were investigated by uniaxial tensile testing. A universal testing machine with an attached heating chamber was used for the tensile tests. Temperature influence was studied through straining of samples until rupture at a fixed strain rate and temperatures of 25, 50, 75, 100, 125, 150, 175 and 200 °C. Strain rate effects were investigated by straining samples until rupture at room temperature and strain rates of 10-2, 5 x10-3 , 10-3, 5 x 10-4 and 10-4 s-1. The effects of temperature and strain rate on NiTi mechanical behavior were discussed in terms of critical stress to induce martensite and austenite yield strength, when applicable; upper plateau stress, transformation plateau length and ultimate plateau stress. It was found that increasing test temperature and strain rate shifted the stress-strain curve upwards, albeit temperature displayed a greater influence. Plateau length increased with temperature, but no significant changes were detected as a result of different strain rates.

Aug 17, 2017

By Charles Austin

IN an earlier series of studies on 18-8 stainless steel at 600°, 700°, and 800°C.1 one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manu-factured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in, dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0,07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recom-mended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 750°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8 -in. dia., air cooling followed the annealing treatment. These treatments per-mitted two direct comparisons: (1) between the 1150° and 950°C. treat-ments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950° and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940

By L. Douglass Anderson

Fox some years past the annual reviews of the metallurgy of lead have almost uniformly stated that there have been no great changes, such as there were, being more particularly noticeable in the refinement of details. While this is quite true, nevertheless these changes in details are gradually bringing about a condition that, taken as a whole, constitutes a considerable advance in the art. Local circumstances have often -compelled metallurgists to adopt certain peculiarities of practice which -upon trial have been found advantageously applicable to more than the restricted district of origin. This paper will deal with some of the more novel features developed in recent years at the United States smelter, Midvale, Utah, particularly with reference to the influence of the bag house. The plant is equipped with six blast furnaces, 48 by 160 in., mechanically fed; four Wedge furnaces for roasting matte and sulphide ores; four Dwight-Lloyd sintering machines; 20 converter boxes for blast roasting; storage bins for ore, fuel, and fluxes; "oxide" and "sulphide" sampling mills; bag house taking all the gases of the plant; arsenic plant for treating the dust gathered there; laboratory, shops, etc. The most marked feature of the plant is its complete bag-house system. Of the many schemes thus far tried for preventing damage to surrounding agricultural interests the writer is aware of none as yet quite as efficient as the bag house. A common remark of visitors upon approaching the plant and viewing the clear stacks is that it appears to be shut down, whereas once inside all the evidences of industry are found.

Jan 7, 1914