Search Documents

By Ludy C. Motta, Denise C. O. Nascimento, Sergio N. Monteiro

"Natural cellulose-based fibers are nowadays of growing interest for modern industrial composites. Relatively unknown fibers like piassava, curaua and gourde have shown promising behavior as reinforcement of polymeric composites. However, the hydrophilic characteristics of the natural fibers impair its adhesion to the normally hydrophobic polymeric matrix. Surface treatments can, in principle, improve this adhesion and the fiber/matrix interfacial strength. In this paper, the effect of alkali treatment of the surface of piassava (Atallea funifera) waste fibers was investigated in terms of the change in strength of epoxy composites reinforced with these waste fibers.IntroductionThe consequences of global warming and the increase in the price of petroleum are motivating the use of natural materials as substitute for energy intensive synthetic materials [1]. In particular, natural fibers obtained both, from cultivated plants such as jute, sisal, hemp and flax as well as from industrial waste such as sugar come bagasse and coir, are being considered to replace synthetic glass fibers [2,3]. These natural fibers, also known as lignocellulosic fibers, present the comparative advantages of being renewable, recyclable and biodegradable. Moreover, lignocellulosic fibers require less amount of processing energy and are neutral with respect to CO2 emission, which causes the atmospheric greenhouse effect responsible for the global warming [4]. Low cost is another important economical advantage of the natural fibers over the synthetic ones and the application of lignocellulosic is also associated with a lower wear of processing equipment and better finishing of molded components [5]. Moreover, for some fibers, properties such as the mechanical strength and impact resistance can be superiors to the corresponding properties of synthetic glass fiber [6]. The characteristics and properties of several lignocellulosic fibers are, nowadays being extensively discussed in the literature. It is beyond the scope of this work to comment on the hundreds of papers dealing with this subject. However, there are still less known fibers with great potential as engineering material that deserves investigation."

Jan 1, 2008

By J. F. T. Agapito

Stability in Exxon's Colony Pilot Mine in the Piceance Creek Basin, Colorado has been monitored by periodic pillar stress-determinations End roof-to-floor convergence measurements since 1971. Pillar failure has caused marginal stability in some areas of the mine. Measurements taken during the process of failure provided valuable information on the in-situ pillar strength and long-term behavior of the mine structure. Four pillars were reinforced by 32 mm (1-1/4 in) diameter tensioned grouted bolts to increase long-term stability in the northern area of the mine. Stability of this area is necessary because future plans envision its use as an exit/access and ventilation exhaust. Computer analyses were performed to help evaluate the effect of pillar reinforcement on long-term stability. Results indicate that bolting is particularly useful in stabilizing failed pillars, but its effects are significant only in the immediate area of the pillar. The projected significant decrease in deformation of two extensively failed pillars near a main entry indicates that bolting reinforcement will assist the long-term stability of the opening.

Jan 1, 1985

By Robert Lindsay

A NUMBER of detailed investigations of the physical changes accom-panying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theo-retical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suit-able variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions.

Jan 1, 1939

By Charles David

This work aimed at evaluating the effect of pre-strain of Lean Duplex UNS S32304 on anodic dissolution and hydrogen evolution reaction rates in acidic chloride media. Interrupted tensile testing was employed in order to generate different deformation levels. Potentiodynamic experiments allowed to detect a decrease on the cathodic and anodic reaction rates as a consequence of plastic deformation. A non-linear evolution of corrosion rates was observed, probably as a consequence of the evolution of specific dislocation structures in the material. Strain also caused a slight ennoblement of the ferritic phase, while austenite became a little less noble. These behaviors are analyzed in terms of residual stresses, characterized by X-ray diffraction.

Aug 17, 2017

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By K. A. Natarajan, I. Iwasaki

The effect of poisoning on the behavior of platinum electrodes in redox potential measurements in metallurgical systems was studied in the presence of such inorganic surfactants as cyanide and sulfide and such organic surfactants as dodecylammonium acetate, trimethyldodecylammonium chloride, potassium ethyl xanthate, and potassium diethyl dithiophosphate (Aerofloat®). These chemical species represent, more or less, typical constituents encountered in leaching, flotation, and sewage treatment systems. Triangular wave voltammetry was used as the experimental technique to study the nature of poisoned surfaces. Among the species studied hydrogen sulfide and dodecylamine were found to form a resistant surface film affecting charge transfer. Platinum electrodes appeared to have a weaker tendency to adsorb sulfide species in alkaline pH ranges, while cyanide, xanthate, and dithiophosphate affected the normal electrode behavior differently. Possible methods of reactivation of a poisoned electrode by mechanical cleaning are suggested.

Jan 1, 1974

By K. Adam

Grinding in steel mills adversely affects the flotation of pyrrhotite. The electrochemical nature of inter action between pyrrhotite and active metals was investigated by contacting pyrrhotite with platinum at different applied potentials. Flotation tests, scanning electron microscopy, Auger electron spectroscopy, and X-ray photoelectron spectroscopy were wed to examine the surface properties of pyrrhotite. The formation of hydroxide or oxide and sulfate species of iron through the oxygen reduction reaction at the cathodically polarized surface of pyrrhotite was shown to be the mechanism responsible for the reduced floatability of pyrrhotite.

Jan 1, 1985

By S. Kelebek

DETA exhibits a highly selective depressant action on pyrrhotite without adversely affecting the collectorless flotability of pentlandite and chalcopyrite in nickel-copper ores of the Sudbury region. A simplified Eh-pH diagram has been constructed to illustrate the extended stability of elemental sulphur and to explain the collectorless flotation of pentlandite and chalcopyrite. Cu and Ni ions, which are known to exist on the surface of pyrrhotite, promote the flotation of this mineral whether a collector is present or not. Thermodynamic calculations indicate that the action of DETA involves the sequestration of Cu and Ni ions from surfaces under a wide range of redox conditions; analysis of flotation test filtrate indicates as much as a 20-fold increase in the concentration of Ni and Cu ions. It appears that DETA may enhance the self-hydrophobicity of chalcopyrite and pentlandite by exposing more of the sulphur-rich surface sites for bubble contact in flotation. There are various possible explanations for its depression of pyrrhotite

Jun 18, 1905

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

By H. Fukushima, T. Ohgai, N. Baba

The electrodeposition behavior of Zn and the morphology of the deposited Zn were studied in electrowinning solutions containing polymer additives such as gelatin and polyethylene glycol (PEG). The cathode potential was shifted in a less noble direction and the polarization resistance for Zn deposition increased with increasing concentrations and molecular weights of both gelatin and PEG added to the electrolytic solutions. However, when the molecular weights of these additives exceeded about lxlO4, the cathode was depolarized and the polarization resistance for Zn deposition decreased with increasing molecular weight. The crystal grain size and the (002) orientation of the deposited Zn became smaller when the concentration and molecular weight of the additives increased, and the cathode was polarized.

Jan 1, 2000

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation's industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By Ven Mercade

The flotation and, more importantly, the depression of calcite has been extensively studied, especially in terms of collector, pH, and metal ions. A basic laboratory study was undertaken to determine the effect of metal cation, pH, and hydrosol concentration on the flotation of calcite. Results indicate that at constant pH and soluble-silicate and metal-ion concentration, flotation of calcite decreases in the order: [ ] In the case of metal-silicate hydrosols, a higher pH of formation results in higher calcite flotation recovery. Data are insufficient to permit any conclusions regarding the behavior of mono- and trivalent ions. Possible theories to explain the foregoing observations are developed in the paper.

Jan 1, 1981

By G. M. Zhao

The gasification of lump coke with CO2 was studied in a fixed-bed reactor. The effective diffusivity of the gas was evaluated from measurements of the reactivity of the lump coke, produced by BHP Steel in New South Wales, and from kinetic parameters that were determined from the reactivity of fine grains. The grain model of effective diffusion in porous media was adopted to express the gasification rate of the lump coke and was found to fit the experimental data well. The relationship between reactivity and textural characteristics of the coke was examined

Jun 18, 1905

By S. S. Rahman, A. Gholami, M. A. Aghighi

"This paper provides a foundation for studying the growth of fractures in presence of other discontinuities and different anisotropies of low permeable hydrocarbon formations and helps to improve the design strategies for multistage fracturing.The multistage fracturing technology has recently been used to exploit low permeable hydrocarbon reservoirs. However, the mechanism of hydraulic fractures interaction and the impact of local heterogeneities on ultimate trajectory of the growing hydraulic fractures are not yet understood in depth. A fully coupled poroelastic Finite Element based model is developed to investigate the mixed mode propagation behaviour of growing hydraulic fractures. This model takes advantage of an explicit representation of the fracture which enables us to take the effects of rock and fluid related parameters into account. Moreover, impact of fracture geometry and leak-off phenomenon is investigated. The refined mesh around the crack provides the added advantage of more detailed stress distribution, pore pressure change and back stress in the vicinity of the fracture and in particular at the fracture tip. The potential deviation propensity of the fractures is evaluated based on the fundamental rule that fractures propagate perpendicular to the direction of the minimum horizontal stress.This study shows that pressurization of transverse hydraulic fractures results in the reorientation of local principal stresses, particularly in vicinity of fracture tips. Variation of flow patterns clearly influences the evolution of shear stress around the fracture tips which will potentially lead to mixed-mode I and II fracturing and consequently, fracture deviation. The presence of local heterogeneities such as preexisting fissures and/or fractures is a main source of such pore pressure induced stress redistribution and reorientation and potential deviation of hydraulic fractures.Most existing models ignore or simplify the effect of pore pressure/stress coupling as well as the fracture geometry and fluid flow within the fracture. Also, the fluid leak-off from the hydraulic fracture into the formation, which is a controlling factor in fracture growth, is often considered using analytical models. Taking advantage of a fully coupled porelastic model along with an explicitly discretized fracture, this study provides a more realistic insight into the complex fracture propagation processes of multistage fracturing operations particularly in presence of reservoir geo-mechanical complexities."

Jan 1, 2015

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By Gheorghe Marin, Franco Chiesa, David Levasseur, Bernard Duchesne

Over the past 20 years, pressure die casting has evolved to a point where structural parts can now be produced by this process. This has been made possible by the development of vacuum die casting and by the development of die-castable, low iron content alloys. This resulted in the production of low porosity, weldable die-cast parts on which heat treatment may be applied. In the present paper, the influence porosities on the tensile properties of as-cast A360 tensile test bars was evaluated. This was done by casting 24 clusters, comprising three 6mm diameter test bars each, in a 280T cold chamber pressure die casting machine after a steady dynamic equilibrium had been reached. Modeling of filling allowed to explain the differences in porosity observed in the 3 samples of a same cluster while the results of solidification modeling were related to the microstructure. Tensile samples were radiographed on a real time X-cube apparatus and separated into 2 lots: samples where no porosity defect were visible and samples with visible defects. By measuring the tensile properties of the 2 lots it was possible to quantify the drop in tensile properties brought about by porosity, which is the most common defect observed in pressure die-cast parts.

Jan 1, 2015

By Chih-Huey Lin

The Au/?-Al2O3 catalyst prepared by AuCl3 impregnation is subjected to the influence of residual chlorine after an oven drying. A post-impregnation NH4OH treatment was able to eliminate chlorine, and to reduce the cluster size of Au moiety. However, the CO oxidation activity was not increased by this post-impregnation NH4OH treatment. This suggests that certain metal-support interaction (MSI) is the determining factor for the activity of Au catalysts. Thermal treatment under H2, O2 or He was attempted to increase MSI of the prepared catalyst with or without the post-impregnation NH4OH treatment. No significant activity enhancement was found but the TPD analysis suggests that a H2 treatment has a higher chance to induce MSI.

Oct 1, 2003

By Yang Hong-ying, Yu Juan

Electrochemical behavior of natural chalcopyrite in electrolyte solution at pH value of 6.97 was studied by cyclic voltammetry, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. The results showed that the electrochemical processes occurred on electrode surface were controlled mainly by the growth of sulfur species at lower applied potentials (<0.35Vvs.SHE), and the oxidative dissolution of sulfur species and the hydroxylation of iron at higher applied potential (>0.45V). The EIS spectra of oxide product layers could be illustrated by the equivalent circuit of Re(QdlRct(QfRf)), and the degree of hydrophilicity for chalcopyrite was higher when the value of charge transfer resistance Rct. was greater. The optimum potential range for the floatation of chalcopyrite in collectorless solution at pH value of 6.97 was between OCP (0.165V) and 0.35V.`

Jan 1, 2015

By D. S. Fuerstenau, S. Chander

The results of a preliminary investigation undertaken to explore the possibility of treating potential in sulfide mineral flotation systems as an external variable are reported in this note. Two different methods were used to assess floatability. One involved measurement of contact angles at a mineral electrode in reagent solutions, and the other involved direct measurement of flotation recoveries in a Hallimond tube flotation cell that had been modified such that mineral particles were in electrical contact with a gold electrode. Fairly good correlation between the contact angles and flotation recoveries has been obtained.

Jan 1, 1976