Search Documents

By Richard M. Chamberlin

Perlite is an altered rhyolitic glass with 2 to 5 wt % water that expands or "pops" when heated quickly to plasticity while evolving steam to form lightweight, glass foam. Commercial perlite deposits in New Mexico are well-developed zones of chemical weathering (hydration) superimposed on highly permeable and thick glassy zones at the chilled upper surface and toes of high-silica-rhyolite lava flows and lava domes. The maximum tonnage of glass in these volcanoes was predetermined by their unique eruptive histories. New Mexico perlite production (80% of US production of 571,00 st) is mostly from the 3.9 Ma high-silica-rhyolite lava flows at the No Agua Peaks volcanic center. The primary vent at No Agua is defined by a 900 ft-high rubidium-rich composite lava dome, known as West Peak, that contains minor perlite reserves. Slightly less rubidium-rich lava squeezed out from under the west flank of the dome to form relatively thin (250 ft) but highly vesicular lobate flows that now consist of about 50 % recoverable perlite. Finally, rubidium-poor lavas were extruded from a radial dike on the northeast flank of the dome. These thicker (400 ft) flow lobes contain about 20 % recoverable perlite. The largest mass of lava does not always contain the most perlite. The thinner (west) flow at No Agua yields the largest perlite reserves rather than the large composite lava dome or thicker (east) flow.

Jan 1, 1994

By M. A. Alan

The Bellavista Gold Deposit lies 75 Kms north west of San Jose, the capital of Costa Rica, Central America and 3 Kms north east of Miramar, in the Province of Puntarenas. The total road distance from San Jose to the deposit is 120 Kms all paved road except for a 2.5 Km graded, gravel road on the property (Figure 1). Infrastructure services in the Miramar-Puntarenas area are well developed with electrical power distribution, a modern port facility and community services being available. The deposit lies on the south west flank of the Tilaran Mountain Range between an elevation of 550 and 800 meters above sea level. The local topography is steep, originally covered with pre-montaine, tropical wet forest vegetation which has been largely destroyed due to clearing for cattle grazing. The annual rainfall is approximately 2,950 mms, 90% of which occurs between May and October.

Jan 1, 1992

By F. Harold Weber

On July 13, 1967 the San Bernardino County Planning Commission approved publicly a request by American Smelting and Refining Company for a zone variance to conduct a silver mining and milling operation in the Calico district, southern California, Coincidentally, on July 14 the U.S. Treasury halted its sales of silver, and the U.S. free market price quoted rose immediately from $1.30 to $1.77 per ounce. In its request to the commission Asarco stated that about 13,500 to 15,000 tons of rock would be moved daily by surface mining, including 7,000 tons of ore. The ore would be crushed to minus three-quarters inches and the silver recovered "by a chemical process." The grade of the ore was not given, but the company said that it might also recover barite as a byproduct, The operation would employ 150-160 people. Additional activity in the district includes exploration programs by Superior Oil Company and Calico Silver Mines, Ltd. History and production: In retrospect, as the price of silver began to rise in 1961 from 91 cents an ounce, and as Asarco began its exploration program in late 1964, a new era for an old bonanza silver district would seem to have begun. The Calico district has been mined for silver only on a very, very small scale since 1882 to 1896, when an estimated $12 to $20 million (perhaps 15 to 20 million troy ounces) of that metal was produced from the 50-odd mines of the district and vicinity. These mines include the Silver King, Oriental, Waterloo, Garfield, Odessa and Waterman (which is about 8 miles west of the district). Much smaller-valued amounts of barite, gold, lead, and copper also have been produced from the ore deposits of the district; and from 1884 to 1907 the region yielded about $9 million worth of borate minerals.

Jan 1, 1967

By Cotton R. E, Cox R

Digger Rocks is one of several nickel-bearing sulphide deposits localised within komaLiitic volcanics of the Forrestania Greenstone Bell within the Archaean YiIgam Block of Western Australia. Exploration and evaluation to April 1990 have delineated a resource, at a nominal cut-off grade of 0.5 per cent Ni, of 1.9 Mt at 1.1 per cent Ni within a lensoid sulphide body which strikes NW, dips 50°SW, and occurs at a depth of 30 - 110 m below surface. There has been no production from any of the Forrestania nickel deposits to-date. The deposit, comprising both disseminated and massive sulphides, has maximum dimensions of 400 m strike, 115 m vertically and 90 m true width. Generally the massive sulphides occur at the base of the disseminated sulphides, on or close to the base of the Digger Rocks dunite. The two main massive sulphide lenses have maximum dimensions of 120 m strike, 75 m vertically and 16 m true width (northern lens) and 60 m strike, 25 m vertically and 4 m true width (southern lens). The average grades of the massive and disseminated sulphides are 5.9 per cent i and 1.2 per cent i respectively. The massive sulphides generally have sharp hangingwall and fOOlwall contacts and display strong internal grade anisolropy.The massive sulphides are mainly within the supergene zone and consist of violarite, pyrite and marcasite. The disseminated sulphides are mainly within the primary zone and consist of pentlandite, pyrrholite, pyrite and minor chalcopyrite. Alteration zones, up to six in number, are complex in detail. The sulphides are capped by an average of 30 m of sub-economic, leached, siliceous, oxidised material.A genetic model for the deposit is described which places Digger Rocks in Category 2 (sulphides in large layered dunite bodies) of the latest classification of komatiitic nickel sulphide deposits in the Yilgam Block of Western Australia by Hill and Gole (1990).

Jan 1, 1992

By Graylin R. K, dea T. R, O&apos

The Wolgan Seam of the Upper Permian IlIawarra Coal Measures of the Western Coalfield of New South Wales consists of high volatile, low sulphur, medium hard coking coal with high fluidity. This seam, 1·8-2·4m thick, in the Wolgan area, dips gently at 1°_20 ENE and lies at 160-440m below the deeply dissected surface of the western margin of the Blue Mountains plateau.A detailed study of the deposit has revealed that the Wolgan Seam consists of four main coal plies separated by three distinct stone bands. Each of these subunits is lenticular and displays individual physical, chemical and mineralogical characteristics which exhibit distinct spatial distribution patterns across the area. Most noticeable is the presence of long linear ESE-trending zones of low ash - high volatiles - high fixed carbon - high fluidity which delineate the major distributary pattern within the deltaic environment of coal formation.This seam contains some of the highest fluidity coal in the world.The Wolgan area, close to the western margin of the Sydney Basin, is characterized by:I. a regional, closely spaced, homogenous joint fracture pattern dominated by an orthogonal pair set trending 3400 and 0700, to which the face- and butt-cleat directions respectively of the Wolgan Seam are sub-parallel, and2. a more widely spaced, heterogenous, cross-cutting pattern of regional structural fractures. Zones of bad roof conditions are probably associated with these lineaments which are subvertical and trend in three majordirections, viz., 005°,035° and 115°.

Jan 1, 1980

By Thomas W. Mitcham

A program of geological research in support of mineral exploration efforts is outlined. Specific goals are stated, approaches to accomplish their attainment are described, and the type of useful results to be expected are outlined. Because mineral exploration or prospecting has intensely practical goals, research in support of it must be applied research, applied to the problem of maintaining or increasing the discovery rate of the exploration effort. To attain research goals, attention to personnel selection, group structure, and program are critically important, and in about that order. A large percentage of the professional personnel should have had experience in mining geology or mineral exploration, and they all should be prospector-oriented. Structuring in the group should be at a minimum, with wide allowance for the kind of independent research which is essential to the nurturing of on-target creativity. The program should be field-oriented, and it should include a wide representation of those subdisciplines of geology which are applicable to mineral exploration. The types of results to be anticipated include improved or new conceptual models for various types of orebodies and their settings from which new ore guides can be derived, new exploration techniques, and the development of a knowledge bank for various aspects of the exploration effort.

Jan 1, 1968

By Brian W. Mackenzie

The paper addresses five questions concerning the economic of gold exploration in the western Canadian shield. Can historical footprints be used to project future gold prices for exploration planning? Experience suggests that gold price forecast are too clo ely tied to current market events to provide meaningful guidelines. What range of breakeven gold price will typically be required to ju tify gold exploration in Canada? Minimum price requirements. initially asses ed at $540 to $1080 per ounce, probably lie in the range of $480 to $760 per ounce (expressed in 1985 Canadian dollar). Within Canada, what role do regional conditions and taxation policies play in determining the viability of prospective gold exploration targets? Striking interprovincial differences are found to exist, given the same geological circum tance -Nova Scotia, ew Brunswick, and Quebec rank towards the top in term of motivating exploration, Briti h Columbia provides the least investment incentive, while Saskatchewan and Manitoba place around the middle of the Canadian league. How can minimum acceptable tonnage-grade conditions for gold targets in the western shield be established and, then, constructively applied to provide exploration planning guidelines? Minimum target conditions, realis tically defined in terms of a broad band of doubt, can be used judiciously to help balance the direct costs of uneconomic exploration with the opportunity costs associated with rejecting economic deposits. How does the average cost per ounce of gold discovered in the western shield compare with the overall Canadian experience? Average discovery costs for the we tern shield, apprai ed at $100 per ounce, are shown to compare favourably with the Canada-wide record.

Jan 1, 1986

By Toshihide Ito, Jie Liu, Takashi Nishiyama

"Human society evolved from an agricultural to industrial and, subsequently, to a service society. As the resource requirements for each stage of this development differ, trends of metal and energy consumption are related to shifts in society. The increase pattern of supplemental energy is similar to that of mineral production throughout the world. Low positive and stable long-term increasing occurred before 1950, whereas they increased quickly after 1950, especially between 1950 and 1973. A substantial decline in· the growth of energy and mineral production began in 1973 and lasted until the early 1980s. Production of energy resources has recently begun to increase again at a high growth rate in the world. Observing the consumption trends of energy and key metals, it is clarified that increasing patterns can be thought in three stages.IntroductionHuman society evolved from an agricultural to industrial and, subsequently, to a service society. As the resource requirements for each stage of this development differ, trends of metal and energy consumption are related to shifts in society [1-3]. Humphreys [4] described that both the non-ferrous metal consumption and the construction material consumption showed a similar trend dropping markedly in the UK over the period 1960-1992. On the other hand, per GDP (Gross Domestic Product) consumption, that is, the intensity of use of construction materials has declined sharply over the past 30 years, more so than the intensity of metal use in the USA [5]. Nishiyama [6] observed that increase pattern of supplemental energy is similar to that of mineral production throughout the world."

Jan 1, 2000

By Carlos Gualdron, Elizabeth Gomez, Rafael Bolivar

The productivity index of the Coopracarcegua Ltda., a mid-size coal mining company of Norte de Santander, Colombia, was related absenteeism using accident, productivity and profit data four years. The analysis was based on type, severity and frequency of accidents, number of absentee days; price per metric ton, and other relevant parameters. The enterprise is formed by 5 different mines of thermic coal, each one with different exploitation technologies and different productivity. Each mine was analysed separately and the loss of profit due to absenteeism was calculate for each one. The study showed that the foregone earnings due to absenteeism in terms of the whole productivity of the enterprise was about of 6.6% of the total profit average the 4 years, with calculated values of 14.7%, 3.5%, 8.4% and 4% per year in the evaluated period. The study identified that the most important cause of absenteeism was "General Disease". The foregone earnings in 2009, the highest loss for the analysed period, was about US$ 0.937 million and during the whole evaluated period was US$ 2.46 million.

Jan 1, 2014

By W C. Burton, J S. Kuszma, T O. Aspinall

The environmental impact of mining and evolving environmentallegislation has received increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental regulatory agencies and members of the public. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. There is thus the need to increase the base of knowledge on the existing practices of spoil dump design and rehabilitation. Efficient engineering design and systematic economic evaluation of spoil dump reshaping techniques for mine rehabilitation assists in maintaining the expected standards of environmental compliance. As part of the overall approach for effective engineering design ofspoil dumps, a comprehensive, computational and efficient tool isrequired for assessing the economics and productivity of existing spoil dump reshaping practices for efficient mine rehabilitation. Such a design tool is useful in linking current spoil dump environmental management practices with engineering design planning and economic impact evaluation. This paper identifies the processes for the economic impact evaluation for existing spoil dump reshaping practices and proposed final site dump designs. Selection of an efficient spoil dump design at optimum costs will ensure operational efficiency. A case study is presented identifying economic impact evaluation in earthmoving equipment selection and the costs involved for the reshaping of spoil dumps to that of varying final site designs.

Jan 1, 2000

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Stanley G. Butcher

"The methods generally applied to predict performance and financially evaluate beneficiation options are reviewed.Typical costs f or a western Canadian thermal coal operation are examined. Preparation-from truck dump to loadout-frequently amounts 10 over a quarter of total minesite costs. Failure to achieve projected yield-whether caused by mine or plant problems-s-substantially increases production costs because more coal has 10 he mined to meet a specific market demand. Problem identification by mass/ash balances is recommended.Thorough characterization of the coal and associated waste materials and more reliable prediction of beneficiation process performance are therefore essential to determine a project 's financial viability.IntroductionWestern Canadian coal prep a ration plant capacity is partway through a massive expansion program . In 198 1 potential product ion was 14 million tonnes, by 1985 it will be 26 million tonnes per year. Only two years ago the industry was concerned whether it could sustain this rate of growth to meet market demands : now with diminished market demand and lower coal prices being offered by our international competitors there are doubts whether t his potential will be fully employed , even by 1990.One direct consequence o f the occurrence of a variety of coals in a stunningly beautiful but complex geo logical setting such as the Rocky Mountains and their Foothills is that each project is unique. Coal is a low value per tonne product. To supply distant markets from geographically isolated deposit s necessitates expensive , dedicated , infrastructure . T o be profitable these operations must achieve eve ry advantage of the economy of scale.Each of the mi ne complexes commissioned in the 1970s experienced severe problems in the area o f co a l preparation . Most bought their way out , paying for major plant modifications by increasing the scale of their total operation . The current market recession may not allow new operations this route to profitability.The objective of this paper is to illustrate the economic impact of coal preparation problems on the profitability o f the total minesite operation and thus provide a sound basis for decision making process."

Jan 1, 1985

By Wayne Hilgedick

Peabody Coal Company is the nation's largest producer of coal and is headquartered in St. Louis, Missouri. In 1978 Peabody divisionalized its operations to establish more responsive and effective mine management. Peabody Coal Company's Arizona Division operates two large surface mines, the Black Mesa and Kayenta Mines. Both are located in northeastern Arizona, approximately 30 miles from Kayenta, Arizona, on the Navajo and Hopi Indian Reservations. The Black Mesa Mine produces 4 to 5 million tons of coal per year and the Kayenta Mine produces 7 to 8 million tons per year. Coal from the Black Mesa Mine is transported 274 miles by coal slurry pipeline to the Mohave Generating Plant located on the Nevada/Arizona border at Bullhead City, Arizona. This plant is jointly owned by Southern California Edison, the Los Angeles Department of Water and Power, Nevada Power Company and Salt River Project Agriculture Improvement and Power District.

Jan 1, 1983

By J. C. Agarwal

Do large-scale projects in mining and smelting start up and achieve expected capacity on schedule? In most cases not. Regardless of worldwide location, company know-how, or financial backing, unforeseen delays occur. A comprehensive CRA study for the World Bank shows that delays are the rule, not the exception, in most mining and smelting projects. When delays are not factored into analysis and planning, financial projections are, literally, not to be believed. Returns on investment will seldom achieve their targeted level because of startup delays. This paper reviews the results of our analysis of startup of new mines, mills, and smelters; provides a detailed discussion of why delays occur in the smelters and refineries; presents the cash flow implications of startup delays; and discusses preventive measures that should be taken to avoid financial shortfalls,

Jan 1, 1983

By J. C. Agarwal

Most metals are produced from minerals containing one or more of the desired metals, some contaminating metals, silicate, oxides, carbonates, and sulfides. Therefore, in the production of metals, there is generally a gaseous effluent in pyrometallurgical processes and a liquid effluent in hydrometallurgical processes. There are also solid residues such as waste ore, tailings, dust, and slag, created by the metal recovery processes. There are two important distinctions between the effluents and the residues: I. Effluents ? gases and liquids ? affect the neighboring environment for miles from the point of emission, while residues affect only the soil on which they are stored or dumped. 2. The environmental and economic effects of effluents are known and felt essentially immediately. By contrast, the environmental effects of the residues may not be known for a long time. For these reasons, the economic impact and the potential corrective actions required are very different for effluents and residues.

Jan 1, 1992

By Chris Weyand

Throughout the past 40 years we have been drawing inevitably closer to the conclusion that coal will be our chief source of energy. Our reserves of natural gas and petroleum, on which we depend, are dwindling. Knowing that we will soon reach our physically extractable limit of these energy sources. The US government has created many incentives to encourage energy companies to transfer technology and resources from natural gas and petroleum to coal. Such encouragement is stimulated through taxation methods. Coal mining engineers deal mainly with production, which involves planning and design throughout the acquisition, exploration, development, production, and reclamation of a mine. Though taxation is not one of the areas analyzed by the engineer, it should be considered and understood as it is involved in the mine life cycle. This paper will discuss coal taxation in the five stages of mining and will explore certain tax saving decisions.

Jan 1, 1983

By G. Richard Dreese, Harold L. Bryant

The coal mining industry has had a long history of successfully externalizing part of its costs. Thus the private or internal costs of coal mining have been minimized and the social or external costs have been ignored. The externalized costs have largely taken the form of water pollution from acid mine drainage and sedimentation of stream channels from eroding spoil banks and gob piles. The environmental problems created by strip mining are very conspicuous, so the public demand for legisla-

Jan 1, 1975

By G. Richard Dreese

Most coal mining states have passed or amended laws restricting strip ruining in the past two years. In light of this and in anticipation of further restrictions by the states and the federal government on strip mining this paper attempts to show the Impact of these new laws on the structure of the coal mining industry in Ohio and specifically on one small stripping firm in Ohio. The implications of the study are applicable to other states under similar circumstances and to other industries which are being caught up in the ecological-economic struggle.

Jan 1, 1973

By H. L. Bourne

The sand dunes which line the east shore of Lake Michigan resulted after the last, or Wisconsin, glacial period in Michigan. Melt-water streams carried vast quantities of glacial debris to the near shore areas of predecessors to Lake Michigan. As the lake levels receded, these vast quantities of sand were exposed to the prevailing westerly winds, which was the last major process that acted upon the sand and resulted in the formation of the dunes. 1 These dunes are one of the significant natural resources within the state. Michigan dune sands supply about 90% of the foundry sand used in the automotive industry, and 40% of the foundry sand used 2 for all purposes within the United States. The deposits owe their importance to the following factors: grain size distribution, grain shape, mineral composition and location with respect to the foundry sand market. In spite of their economic significance these I deposits are in jeopardy through legislative preemption.

Jan 1, 1975

By W. Trask

The state of the art in crawler transporters for loads to 3 kt (3300 st) is sufficiently advanced to allow compilation of job cost figures showing the economics of tracked vehicle use under a wide variety of circumstances. Initial costs, cost per ton of capacity, and operational and maintenance expenses are presented. Data is derived from participation by the Neil F. Lampson Co. in more than 3 Mt - km (2.05 million st - mile) of crawler operation during the past 16 years. The effects of economics on future design trends will be examined with particular reference to versatility, portability, and capacity.

Jan 1, 1987