Search Documents

By P. P. Scott, George C. Howard

During the drilling of wells, fractures which are created or widened by drilling fluid pressure are suspected of being a frequent cause of lost circulation. A study of the variables which are believed by the authors to he related to fracturing led to the premise that the presence of an effective lost circulation material in a drilling mud stream would serve to plug small fractures at the moment they are encountered or created and thereby a a possible cause of lost Circula. tion by preventing fluid pressure from widening and extending the fractures. A large number of lost circulation materials were classified and tested in simulated fractures and in shallow wells. Granular type materials with a gradation of particle sizes were found to be the most effective for plugging. Within the limits of pumpahility, the concentration in mud of each lost circulation material tested was found to be a controlling factor in determining the maximum size fracture which could be sealed. A new type centrifugal sorter was given preliminary tests and found to be capable of concentrating cuttings for rejection and reclaiming lost circulation materials. INTRODUCTION The control and prevention of lost circulation of drilling fluids is a problem frequently encountered during the drilling of oil and gas wells. Lost circulation or lost returns may be defined as the loss to formation voids of the drilling fluids or cement slurries used in the process of rotary drilling and well completion. The loss may vary from n gradual lowering of mud level in the pits to a complete loss of returns. Not to be confused with lost circulation is the continuous reduction in mud volume caused by the loss of the fluid phase of muds as filtrate and the solid phase as filter cake during the continuous filt~ation process which occurs on permeable formation surfaces. The loss of drilling fluids and their costly constituents is only one of the detrimental effects experienced when circulation is lost. The loss of drilling time, plugging of potentially productive formations, stuck drill pipe, blow-outs, excessive inflow of water, and excessive caving of formatioils are other effects which contribute to make the control and prevention

Jan 1, 1951

By G. H. Bruce, C. E. Williams

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By C. E. Williams, G. H. Bruce

The trend toward deeper drilling, together with the attcndant increase in power requirements for circulation of the drilling fluid, has emphasized the need for a critical examination of the factors affecting the removal of bit cuttings from the hole by the drilling fluid. The ability of drilling fluids to lift cuttings is called their carrying capacity. A series of laboratory and field experiments has been conducted to determine the minimrim annular velocity necessary to remove cuttings, and to investigate the effects of properties of drilling fluids on their carrying capacities. Consideration of the results of these experiments led to the following conclusions: 1. Turbulent flow in the well annulus is most desirable from the standpoint of cutting removal. 2. Low viscosity and low gel are advantageous in removing cuttings. 3. Increase in mud weight is effective in increasing carrying capacity. 4. The carrying capacity is higher when the pipe is rotated than when it is not. 5. If turbulent flow can be maintained, an annular velocity slightly higher than the slip velocity of the largest cuttings to be transported should keep the bore hole clean. This implies velocities of 100 to 125 ft per minute rather than the presently used 175 to 225 ft per minute. INTRODUCTION Power Savings by Reduction of Annular Velocities A large portion of the power expended in drilling operations is consumed in circulating the drilling fluid. An important factor in establishing the rate of mud circulation is the minimum velocity in the annulus necessary to remove bit cuttings. Empirically, it has been found that average annular mud velocities of about 200 ft per minute will remove cuttings. It was not definitely known, however, whether annular velocities of about 200 ft per minute were just above the minimum necessary to remove cuttings, or whether such velocities could be materially reduced without sacrifice of the ability of the mud to remove cuttings. It is apparent that if annular velocities could be reduced without impairment of cutting removal, a considerable saving in power requirements would result. Need for Research on Carrying Capacity The ability of a drilling fluid to transport cuttings is called its carrying capacity. Although it has been recognized that the carrying capacity of a mud is affected by mud properties such as viscosity and density1,2,3,4 there have been various views in the industry as to the effects of these mud properties on carrying capacity. The economic importance of the problem of carrying capacity and the scarcity of information on the subject indicated that research on the problem was needed. THE FACTORS AFFECTING CARRYING CAPACITY Qualitative Determination of Factors The mechanism of cutting transport is closely related to that involved in the separation of material by settling processes. A considerable amount of research has been done on settling problems, and discussions of sedimentation theory can be found in standard texts.5,6 Consideration of the information available from these sources, together with consideration of the mechanism of cutting transport, leads to the conclusion that the factors affecting carrying capacity are the dimensions of the system, the physical properties of the cuttings. and the physical properties of the drilling fluid. system Dimensions and Their Effect The dimensions of the fluid circulating system of importance to carrying capacity are the bore hole size, drill pipe size, pump capacity, and pump speed. These dimensions determine the annular velocity of the drilling fluid. Physical Properties and Their Effects The physical properties involved in the interaction between mud and cuttings are the density and shape of the cuttings and the density, viscosity and gel strength of the drilling fluid. The effect of the density factor on carrying capacity is fairly obvious; high density difference between cuttings and fluid results in a low buoyant force and therefore decreases carrying capacity. The effect of cutting shape is less obvious. Although

Jan 1, 1951

By W. B. Lilienthal, J. C. Melrose

The application of Bingham's law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham's law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn' have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham's law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,' following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham's integration of Bingham's law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning's equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,' the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham's equation is defined

Jan 1, 1951

By J. C. Melrose, W. B. Lilienthal

The application of Bingham's law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham's law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn' have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham's law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,' following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham's integration of Bingham's law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning's equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,' the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham's equation is defined

Jan 1, 1951

By Ronald E. Walkington

The U.S. Department of Energy (DOE) is building the world's newest accelerator-based, pulsed-neutron system, called Spallation Neutron Source (SNS). The facility, located in Oak Ridge, Tennessee, is a partnership of six DOE national laboratories - Argonne, Brookhaven, Jefferson, Lawrence Berkeley, Los Alamos, and Oak Ridge. Oak Ridge has the responsibility for managing the partnership and ultimately operating SNS. SNS will provide opportunities for up to 2,000 researchers each year from universities, national laboratories and industry from around the world for basic and applied research and technology development in the fields of materials science, magnetic materials, polymers and complex fluids, chemistry and biology. When completed, this state-of-the-art research facility will provide neutron beams that are 12 times more intense than any other such source in the world. Most of the world's neutron sources were built decades ago. Therefore, it is easy to understand how SNS will provide new research opportunities unavailable elsewhere, and at the same time restore United States leadership in neutron sciences. Neutron scattering research provides valuable information about materials that cannot be obtained through microscopy, X-rays, spectroscopes, or other techniques. The information gained from neutron scattering research leads to improved materials that are used in high-temperature superconductors, powerful lightweight magnets, aluminum bridge decks, jet aircraft, compact and computer discs, magnetic recording tapes, shatter-proof windshields, and many other applications. SNS is like a flashing strobe light providing high-speed illumination of an object and will record the structure of physical and biological materials from plastics to proteins. Because neutrons have no charge, they can penetrate more deeply into materials than do X-rays, light, or electrons and thus reveal bulk structure and properties of materials. SNS will help to understand and "engineer" better materials and the manufacture of better products at the atomic level. Our high-technology society demands new materials that are stronger, lighter, and cheaper yet perform well under severe conditions. SNS, which is designed with the future in mind, will be the leading neutron research facility for many years to come.

Jan 1, 2001

By Raffaella Granata, Daniele Vanni

"This paper presents the drilling and grouting program performed at two abandoned landfills located into former calcarenite rock quarries in Manfredonia, Italy. Tests performed after the abandonment of the landfills detected leachate infiltration into the groundwater, which required the implementation of a remedial program. In order to seal the rock fissures and create an impervious basin at the base of the two landfills, sub-horizontal boreholes were drilled and grouted into the rock under the waste deposits. At the same time, sub-vertical boreholes were drilled and grouted along the perimeter, to laterally confine the landfills. Finally, the landfills were properly capped with an HDPE membrane, geogrid, geotextile and topsoil. The methodology implemented to create a watertight barrier under the two landfills was innovative and cost-effective. Moreover, the drilling and grouting minimized the environmental impact of the remedial work, since the waste remained in their original location and were not affected by the remedial process.IntroductionThe two landfills, “Pariti-1 RSU” and “Conte di Troia”, are located approximately 6 km (4 miles) southwest of Manfredonia, a small town close to Foggia, Italy (Fig. 1). These landfills are located into two rock quarries, formerly used for the extraction of calcarenite (i.e., a weak calcareous sandstone, in tuff facies), and were abandoned in the early 90s. The two landfills cover a total area of about 45,000 m2 (11.2 acres), and mainly include urban solid waste with a depth of up to 25 m (82 ft). The main characteristics of the two waste landfills are listed in Table 1."

Jan 1, 2016

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

By Fred H. Poettmann, J. K. Welchon, A. F. Bertuzzi

A series of gas-lift tests was made which verified conclusions reached from previous studies and which showed that gas-lift performance could be calculated if reasonably accurate data on the producing characteristics of the well are available.' The test installation is described. Its essential features consisted of a rate-of-flow controller to regulate the input gas and an auxiliary string of small diameter tubing to conduct the input gas to the point of injection in the eductor tubing. In general, it was shown that for continuous gas-lift operation, injection should be as deep as possible consistent with available gas pressure and rate of production desired. Calculated curves are presented which completely characterize the gas-lift performance of the well tested. INTRODUCTION A correlation based on field data from a large number of flowing and gas-lift wells, covering a wide range of oper- ating conditions, was developed which permitted the logical design and prediction of the performance of continuous gaslift installations.' The procedure made it possible to calculate the depth, pressure, rate at which to inject gas, horsepower requirements, and the effect of production rate and tubing size on these quantities. As a result of these calculations certain significant facts were brought to light or re-emphasized. The presence of efficient ranges of operation and an optimum injection depth for a given rate of production were shown to exist as well as the fact that the lower the tubing pressure the less the horsepower requirements to lift the reservoir fluids. The fact that the gas lift performance can be predicted by calculation does not mean that any given installation will perform over the entire range predicted. Many of the conventional continuous gas-lift installations will not permit operation over the entire range predicted by calculation (particularly in the efficient range of operation) because of the performance characteristics of the installation. Consequently, field tests were initiated for the purpose of investigating and arriving at a simple continuous gas-lift installation which would operate under all conditions predicted by calculation. The first series of tests involved the use of mechanically operated valves. These valves were slip-joint type valves which are opened and closed by lowering or raising the tubing at the surface by means of a hydraulic jack. These valves were chosen because it was hoped that they could be opened or closed at will and did not depend on the gas pressure in the annulus or the pressure of the fluid in the tubing for their operation. Unfortunately, the valves did not operate satisfactorily and it was imossible to open or close each valve at will. Some limited data were obtained, however, which verified the predicted benefits resulting from the use of lower tubing pressures. In the next series of tests the valves were removed and the gas was injected from the annulus through a 14/64-in. orifice equipped with a reverse check valve. A packer was set below the valve to seal off the space between the 2-in. tubing and 5-in. casing. The injection point was located at 3,810 ft. This arrangement provided satisfactory mechanical operation. However, it was impossible to obtain low rates of liquid production at low tubing pressures as predicted by calculation. A minimum gas injection rate existed below which steady flow was impossible. Liquid pro-

Jan 1, 1953

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By E. D. McMurry

INTRODUCTION Before discussing the use of the free piston; it may be well to explain briefly the type of gas lift valves with which the loo] is designed to function. The gas lift valve ii nothing more or less than a small back pressure regulator. It; construction consists of an outer hous ing covering a seamless metallic bellows in such a way as in form a sealed pressure vessel or pressure dome. To the bellow* in attached a stem and to this stem is attached a .rating member. When the valve is run into the hole, a pre-delermined pressure charge is placed in the pressure dome. As shown in Fig. 1. the valve is furnished in four different major assem-blies. to accomplish good results in different types of wells. The valve is mounted on a pup joint (Fig. 2a) : the eoin-plele assembly is entered into the tubing siring at the desired location. Each valve is furnished with a revere flow check valve (Fig. 2-b) to eliminate any back wash through the mechanism. Valve action is as follows: At any time the casing pressure is allowed to exceed the pressure forces within the pressure dome of the valve, the valve simply opens and passes gas from the rasing annulus into the tubing. When the casing pressure forces arc allowed to bleed to a force less than the pressure force within the dome, of the valve. the valve closes. With this type of construction. it is possible to open and close the valve or valves at will from the surface, the medium of the gas pressure in the rasing annnlus. The cycle of operation is governed by a tine cycle motor valve, commonly referred to as a gas lift interutitter or gas life surfacr controller (Fig. 3). In actual practice. after the well is unloaded only one valve is in operation . . . all other valve.: remain in the closed position. On pre-determined time cycles, it is possible to open and close this operating valve at will, and to pass the desired amount of gas through this valve wheneler needed. This method of gas lift is widelv used and has been found In be very efficient. However, it has long been known that even greater efficiency would be obtained if it were possible to place Piston between the injected gas and the fluid head. The free piston which will be discussed here was designed to accomplish this end and has been found to do so with very satisfactory results. DESIGN AND OPERATION OF THE FREE PISTON Basically. the free piston consist- of a telescoping assembly in which are incorporated the various control and operating parts (Fig. A set of sleeve valves which are opened and closed by movement of the telescoping section is contained in the. tool. A cross section of the free piston is shown in Fig. 4-11, 'rile main body cotain- a seamless monel bellows of the same type as that generally used in pressure charged gas lift valves (Fig. 4-c), and a valve core to permit placing a pressure charge in the bellows before the free piston is placed in service. The bellows is the main control unit of the free piston and performs two function: 1. It governs the opening and closing of the sleeve valves. a.: dictated by the producing activities of the well in which the piston is operating. 2. In its normal position, it holds a rubber packer in an elongated position to permit passage of fluid between the packer and the tubing walls. The lower section of the free piston contains a hydraulic shock absorber which cushions the return of the tool to its

Jan 1, 1953

By C. R. Sandberg, C. A. Connally, N. Stein

This paper describes the results of volumetric efficiency tests on oil well pumps handling gas oil mixtures. The work was performed in a large scale, above ground unit wherein test conditions could be accurately controlled and measured. The main variables studied were gas/oil ratio (including gas from solution and free gas mixed with oil), pump compression ratio, pump stroke length, pump speed, and clearance volume between the valves at their closest approach. Results are presented for two different pumps and for oils of two viscosities. Relatively small amounts of gas entering the pump resulted in large decreases in volumetric efficiency. Under conditions where the pump was operating at reduced efficiency because of the presence of gas, it was found that variation in the clearance volume between the standing and traveling valves had a considerable effect on pump efficiency level. This effect of the valve clearance volume was found to be significantly altered by the viscosity of the oil used in the tests. The effects on pump efficiency of the other variables studied were found to be relatively small over the range of conditions utilized. INTRODUCTION The production of oil by pumping is often hampered by low volumetric efficiency. A direct increase in lifting costs results from low volumetric efficiency. An indirect increase in lifting costs, probably greater than the direct increase, results from additional wear and tear on pumping equipment and from the down-time necessary for the repairs which can be traced to low-efficiency operation. Both increases in lifting costs tend to reduce economically recoverable oil. A number of different factors can contribute to low pump efficiency. A known basic cause of low efficiency is the presence of free gas in the pumped fluid. Pump volumetric efficiency is calculated only on the basis of liquid pumped and because any free gas pumped is discounted, this volume of free gas would represent a loss of pump efficiency. However, gas also causes a reduction in pump efficiency because it is a highly compressible fluid. It is known that pumps some- times "gas lock" because of excessive gas-to-liquid ratios in the pump barrel. Little is known of the role of gas compressibility in the intermediate case where the pump is operating at low efficiency. The opinion exists, however, that oil-well pumps tend to operate at higher efficiency with long stroke lengths at low speeds, but no quantitative studies of these pumping variables have been reported. It was believed that a much better understanding of the variables which control pump volumetric efficiency could be obtained and that possibly some suggestions as to the methods for increasing efficiency might be found from a study of the operation of pumps handling gas under closely controlled conditions. Previous investigators have studied the effects on pump efficiency of such factors as oil viscosity, oil temperature, slippage of oil. past pump plungers, pump submergence, valve size and spacing, pressure above pump plunger and fluid vapor pressure. However, none of these published investigations were conducted with pumps being subjected to large amounts of gas such as might be the case in a pumping well, nor did any of the investigations study the effect of variation in stroke length or pump speed. A large-scale teat unit was therefore constructed for studying the operation of pumps handling gas and for evaluating effects of such variables as pump stroke length and pump speed. PROCEDURE AND EQUIPMENT A schematic diagram of the pump testing equipment is given in Fig. 1. A 45-ft length of 6-in. casing is mounted vertically in a 65-ft tower. Sight ports are mounted in the casing at intervals near the location of the pump intake and the liquid level in the casing. These sight ports are fitted with Lucite windows sealed by neoprene "0" rings. The Lucite windows are machined to conform to the I.D. of the casing so that no obstruction to flow is present along the casing wall. The casing is fitted with a tubing head and 2-in. tubing is hung inside the casing. Pumps are seated in a shoe attached to the 2-in. tubing. A 1-in. polish rod is attacked directly to the pump without any intervening sucker rods. The top of the polish rod is attached to the weight carrier, which contains a number of weights to be used to force the polish rod in against tubing pressure on the down-stroke. This is necessary because a long string of sucker

Jan 1, 1953

By Richard F. Hinds, F. O. Reudelhuber

Application of the conventional depletion drive calculation methods to volatile oil reservoirs results in erroneous estimates of ultimate recovery. In view of the increasing number and importance of volatile oil reservoirs, a special technique has been developed which will result in more realistic predictions using laboratory data obtained from reservoir fluid studies of a specific type. The experimental data are designed to permit continuous material accounting and, therefrom, provide the hy-clrocarbon composition of both the flowing oil and gas phases. The resultant well-stream composition data are then used directly in surface recovery calculations utilizing equilibrium ratios. A step by step procedure, specifically designed for routine use by the practicing reservoir engineer, is presented in an appendix. An actual study performed on a deep Mid-Continent reservoir is used ay an il-lustrathe example. INTRODUCTION It has been a practice for many years to utilize the conventional ma- terial balance methods in conjunction with relative permeability concepts for the prediction of recovery from solution gas drive reservoirs.' Those who have performed such calculations recognize that compromises of several types are necessary in order to reduce the calculations to a reasonable degree of complexity. The most serious assumption involved results from the necessity of treating the produced oil and gas as separate fluids, independent of each other in their behavior. It is further assumed that the gas which is evolved in the reservoir as a result of pressure decline will not yield liquid upon the reduction of pressure and temperature resulting from production through surface equipment. Although these shortcomings have been recognized,' it has been difficult to attempt refinement of calculation procedures since the laboratory data available normally were not of the proper type or extent to permit such calculations. Three general procedures have been available for depletion drive calculations when laboratory fluid data are of the conventional type. Differential Procedure The most simple, and most widely used, method requires use of the formation volume factor and gas sol- ubility data obtained from a differential liberation performed at reservoir temperature. This procedure ignores the differences existing between the fluid behavior in the reservoir and its behavior as it is produced through surface separation equipment. The errors introduced are not serious when dealing with very low volatility fluids and this method may be utilized if the laboratory data indicate only slight differences between the differential data and the flash data obtained from separator tests. Modified Differential Procedure This method was developed when it became apparent that medium volatility fluids evidenced a wide difference between the flash and differential data. The differential data are adjusted by changing from a residual oil basis to a stock tank oil basis. All that is required is multiplication of the differential data by the ratio of residual oil to stock tank oil relative volumes existing for the original reservoir fluid at the determined saturation pressure. This procedure generally results in increased calculated ul-timate recovery; however, such results should be viewed critically. Upon examination it may become apparent that the results are influenced by errors in reservoir liquid

Jan 1, 1958

By G. W. Binkley, G. K. Dumbauld, F. A. Brooks, B. E. Morgan

In recent years, oil well cementing compositions have been developed with low densities, controlled set strengths, and satisfactory thickening times. With the introduction of the permanent-type well completion method for cementing wells, another property—that of rate of filtration or water loss to permeable formations— has become important. Laboratory data show that cement slurries prepared with oil, water, bentonite, and calcium lignosulfonate possess satisfactory thickening times, strengths, and filtration properties for primary cementing of casing and for squeeze cementing with the permanent-type well completion technique. Cementing compositions have been prepared with oil-in-water emulsions varying in composition from 60 cc water and 20 cc oil per 100 gm cement to 90 cc water and 45 cc oil per 100 gm cement. These compositions have contained from 0.4 to 5.0 per cent calcium lignosulfonate by weight of dry cement. Slurries prepared from these compositions weigh 11.4 to 13.1 lb/ga1 and have filtration rates of from 10 cc to approximately 100 cc in 30-min API tests at room temperature. The unfiltered emulsion cements develop one-day tensile strengths of 60 to 220 psi; and the filtered mass sets to tensile strengths of 60 to 150 psi in 12 hours and develops strengths of 320 to 515 psi in seven days when cured at 125° F. Field experience gained from 13 field mixing jobs demonstrates the utility of the emulsion cement for permanent-type squeeze cementing operations. INTRODUCTION In recent years, research in oil well cementing composition has been directed toward the development of cements having low densities, controlled set strengths, satisfactory thickening times, and low rates of water loss by filtration. Two well cementing compositions that have been developed with these properties are the modified cements containing, respectively, 12 and 25 per cent bentonite clay and various concentrations of calcium lignosulfonate1,2 In a search for other ways to incorporate these characteristics in a cementing composition, consideration was given to the rheological properties of oil-emulsion drilling fluids. Many of the desirable properties observed in oil-emulsion drilling fluids are equally advantageous in a cementing composition. For example, low water loss by filtration and low density, which are inherent characteristics of these oil-in-water emulsions, are desirable for many oil well cementing operations. Furthermore, oil-emulsion slurries have lubricating properties similar to those of oil-emulsion muds, a factor which should provide ease of rotation of casing during primary cementing operations. The properties of lubrication and low filtration may be of special value in both primary and squeeze cementing operations encountered in slim-hole drilling. Studies in the preparation of oil emulsion systems have pointed out the need for violent agitation in order to disperse the oil into the water phase. It was thought, therefore,

Jan 1, 1957

By R. H. Jacoby, V. J. Berry

Future depletion performance and ultimate oil recovery from reservoirs producing under volumetric control are often predicted with the aid of a material balance equation. When the reservoir fluid is very volatile, however, certain assumptions implicit in the use of the conventional methods are no longer valid. This is became laboratory differential vaporization test procedures do not adequately represent the reservoir depletion process and the performance of surface separation facilities. In such cases recovery of stock tank oil per unit of pressure decline can be predicted only from a detailed knowledge of the separator conditions and the over-all composition of the fluid entering the wellbore at each stage of depletion. Surface recovery is not simply related to the total quantity of liquid flowing into the well under reservoir conditions. In order to improve predictions for reservoirs which produce volatile oils, a step wise method of calculation has been developed. This method uses relative permeability data and multicomponent flash calculations to predict oil and gas production as a function of reservoir pressure. Calculations are presented for a reservoir containing a volatile crude oil, and predicted tank oil recovery by primary depletion is more than twice that predicted by conventional methods which are known to be adequate for ordinary black crude oils. Calculated maximum produced gas-oil ratio is less than one-fourth of the conventional prediction. Wellstream compositions have also been used to determine variation in stock tank oil composition and liquid content of the separator gas. This information is of particular importance for crude stabilization calculations and for design of gasoline plant facilities to recover LPG and natural gasoline. INTRODUCTION The estimation of oil reserves and the prediction of future recovery performance of petroleum reservoirs is a frequent task of the petroleum engineer. If the reservoir produces under volumetric control, performance calculations for primary depletion are made by combining oil and gas material balances with the gas-oil flow characteristics of the reservoir rock. For black oil reservoirs, the Schilthuis1 type material balance is commonly employed. For gas or gas-condensate reservoirs, where only one phase is flowing under bottom-hole conditions, a more simplified material balance is used. In the period in which these material balance methods were conceived and put into practice, it was common to classify reservoirs according to the type of fluid produced as (1) black oil reservoirs, or (2) gas or gas-condensate reservoirs. Recently, however, deeper drilling and more extensive studies of reservoir fluid properties have led to the recognition of reservoir fluids with phase characteristics between those of ordinary black oils, and gases or gas-condensate fluids. These intermediate fluids contain relatively large amounts of the hydrocarbons ethane through decane and are found in deep, high temperature (250°F) reservoirs. Such fluids are often referred to as high shrinkage crudes or "volatile oils." They are usually characterized by tank oil gravities above 45° API. high solution gas/oil ratios,

Jan 1, 1958

By C. A. Doh, R. Q. Fields, M. Lebourg

A formation tester run on logging cable is now available to the oil industry. It offers a method of safely and rapidly testing possible producing formations in uncased holes. These tests can be made up the hole after running the electric log. Reservoir pressure data is continuously recorded at the surface as the fluid sample is extracted. The tester may be assembled with a reservoir of 1-, 2.75-, or 5.5-gal capacity. A retaining pad on the body of the tool is expanded against the wall of the hole at the exact depth desired; this depth is determined by electrical log control. Two bullets are then fired through the center of the retaining pad which create a connection between the formation and a flow line to the sample chamber. When the chamber is filled, a valve is closed and the fluid sample sealed at maximum pressure. The tool is retracted to minimum diameter and brought out of the hole. Electrical circuits permit a complete recording at the surface of the mechanical operations of the tool as well as the formation pressure build-up and the hydrostatic mud pressure. The tool was introduced commercially during the latter part of 1955 in the Gulf Coasts of Louisiana and Texas. Over 1,000 operations have been made to date (Sept. 1, 1956); 50 per cent of which resulted in successful tests. Failures have been due mostly to ineffective sealing in unconsolidated sands. One major company had 41 successful tests out of 80 attempts with 23 ineffective pad seals. Results for this company were very gratifying as to pinpointing gas-oil ratios, indicating productive permeabilities and aiding in determination of fluid content where electrical log and side-wall coring information were inconclusive. Eight typical pressure curves are discussed (including misruns). Six types of fluid recoveries are interpreted. Eight actual field examples of electric logs, showing the problems solved by the formation tester, are illustrated. The present applications of the tool are discussed: 1. Determination of productive fluid—varticularlv differentiating between gas and oil. 2. Determination of reservoir pressure as an aid to: (a) safety in completion technique, (b) reduction in drilling costs, and (c) reservoir analysis. 3. Determination of minimum gas-oil ratios. 4. Location of gas-oil or oil-water contacts. 5. Recovery of samples for examination and analysis: oil (gravity); gas (hydrocarbon content); water (salinity). Additional applications envisioned for the future are also given: (I) subsurface exploration based on accurate pressure, (2) recovery of fluid samples from the undisturbed reservoir for PVT work, and (3) possible quantitative study of permeabilities or productivity index. Running the formation tester requires no special pre-cautionary measures. Because full hydrostatic mud pressure is maintained at all times, well depth is no problem. Thus, the method allows safe, economical testing in wells which heretofore could only be tested by setting casing. INTRODUCTION A new method of safely and rapidly testing possible producing formations in uncased holes is achieving considerable success. The method offers promise of further advances in reservoir study. Called the formation tester, the new instrument is unique in that it operates on logging cable. It thus offers all the advantages of wire-line operations and becomes an important adjunct to present logging and side-wall coring services. The tester is operated against the wall of the hole at any depth desired. Zones to be tested are usually determined by a study of the electrical and the micro-caliper surveys. Reservoir data, as well as the operating cycle of the tool in the hole, are continuously recorded at the surface during the operation. The tester, as it was originally designed, was capable of recovering a 1-gal sample of reservoir fluid per trip in the hole. Tools with reservoirs of 2.75- and 5.5-gal capacity are now available. The 5.5-gal reservoir is equipped with a segregating system, set before going in the hole, so that the last portion of the recovery (usually 1 gal) is automatically separated from the first portion. This makes it possible

Jan 1, 1958

By Dwight K. Smith

A new pozzolanic composition has been developed for cementing oil wells where moderate to high temperatures prevail. This material is an entirely different concept to other oil well cementing materials, such as portland cements, cements containing additives, or liquid resins. Its characteristics are such that it is not, at present, recommended for use at temperatures less than 140º F. It can he either accelerated or retarded across a wide range of well conditions. This new cement is composed of a pozzolanic material, hydrated lime, and a chemical activator to give it early initial strength. This material can be used in wells from 6,000 to 18,000 or more feet where temperature conditions are similar to those along the Gulf Coast. This cement, when set, has no soluble portion subject to leaching or any compounds that should be attacked by sulfate waters or brines. For this reason, it should be permanent when placed adjacent to formations carrying any type of fluid. The compressive strengths in 24 hours are more than adequate for wells where temperatures are 140°F and higher. These values ore in excess of many other types of cementing composition presently in use in the field. This pozzolanic composition does not retrogress in strength at high temperatures as do some other types of cementing materials. The slurry weights of this material will vary slightly according to the specific gravity and water requirements of the pozzolnn itself. The materials covered herein will mix from 13.5 to 14.3 lb/gal, and will have a waiting-on-cement time comparable to other materials used under the same conditions. Economically speaking, this composition is less expensive than either portland cements or retarded cements presently being used under deep well conditions. INTRODUCTION Pozzolans are siliceous material which, though not cementitious in themselves, contain constituents which at ordinary temperatures will combine with lime in the presence of water to form compounds which have a low solubility and possess cementing properties. The use of pozzolanic materials dates back many hundreds of years and both the ancient Greeks and Romans were aware that certain volcanic deposits, if finely ground and mixed with lime and sand, yielded a mortar which possessed special properties. Generally, the early strengths of such materials were rather weak and were considered insufficient for modern commercial usages. Pozzolanic materials have been used extensively with portland cement in mass concrete to obtain special properties. In recent years, large quantities of certain pozzolanic materials have been used successfully admixed into portland cements for oil well cementing. Pozzolans, being reactive silicates, will combine with the free lime that is an inherent component of set portland cements and thereby. becomes cementitious themselves. POZZOLANS FOR OIL WELL CEMENTING There are many types of pozzolans, some of which are more reactive than others. The quality of the pozzoIan depends on the degree of reactivity, chemical composition, fineness, and other less well understood factors. Some of the more widely accepted pozzolans are those classified as fly ashes, while others are certain materials of volcanic origin. pozzolans which require large vol-

Jan 1, 1957

By H. C. H. Darley

Particles of montmorillonite-type clays consist of plate-like clay crystals stacked face to face. Under certain conditions in a suspension, these particles disperse to individual platelets with the formation of diffuse double layers round each platelet. This action has a profound influence on the rheo-logical and other properties of the suspension. This paper describes a test for degree of dispersion and uses this test to correlate changes in dispersion with changes in viscosity and gel strength. The test is of practical value in determining and controlling dispersion in drilling muds. INTRODUCTION It has long been recognized that the hydration and dispersion of clays, particularly those of the montmoril-loilite type, strongly influences the rheological and other properties of drilling muds, but little has been done to measure either of these phenomena under conditions that exist in drilling muds. The hydration of clays as such has been extensively studied by those interested in clay mineralogy, but in drilling muds it is to be expected that dispersion is at least as important a factor as hydration because of the much higher water-to-clay ratios and the very high degree of mechanical agitation. The term dispersion as generally applied to colloidal systems means the subdivision of large particles to small. Particles of montmorillonitic clays, however, consist of plate-like particles stacked face to face. Dispersion of these aggregates to individual platelets may be expected to have an unusually large influence on the properties of the suspension because of the shape factor, the enormous increase in specific surface, and the pronounced surface phenomena exhibited by the crystal surfaces. It is this form of dispersion that is particularly considered in this paper, -and the term degree of dispersion is used to imply the number of platelets per particle. The term aggregation is used to denote the opposite of dispersion, the association of individual platelets face to face to form stacks. It is important, as Garrison' has pointed out, to distinguish between the deflocculation-flocculation phenomenon and the dispersion-aggregation phenomenon. Flocculation of clay suspensions is characterized by the formation of voluminous sediments that are stable under quite high centrifugal fields. This indicates an edge to plate association of particles to form an open network type of structure, which obviously will have quite a different influence on the properties of the suspension than aggregation of the platelets face to face. The work described in this paper was primarily concerned with developing a test for degree of dispersion in clay suspensions and by means of this test to follow changes of dispersion brought about by addition of electrolytes and to show the influence of dispersion on the rheological properties. The Clay-Volume Test This test is based on the assumption that the greater the number of particles per unit weight of clay in a suspension the greater will be the volume of sediment when it is flocculated under standard conditions and centrifuged. After considerable experimentation the following procedure was established: 1 cc of the test mud vigorously shaken with 100 cc of 1-N NaCl in an ASTM oil centrifuge tube and centrifuged for five minutes in an International No. 2 centrifuge at 2,000 rpm. When drilling fluids of different solids content are being compared, the clay volume is expressed in cc per gram of clay solids, but generally changes in dispersion in a given mud are being compared and it is more convenient to report as cc of sediment. The test is strictly a comparative test, so that it is not necessary to adhere to the conditions specified above, e.g., with field muds a stronger flocculant such as Al2(SO4)3 may be preferable to NaCl.

Jan 1, 1958

By D. Perry, G. W. Binkley, G. K. Dumbauld, F. A. Brooks

A new cementing technique has been developed which is particularly applicable to permanent-type well completion operations. The technique makes use of the accelerating effect of calcium chloride on setting time and strength development of cement cake deposited in squeeze cementing. An unique feature is that the accelerator is applied after the unaccelera-ted cement slurry has been squeezed and the excess has been reversed from the well. Laboratory data on the accelerating effect of calcium chloride applied to the fi1ter cakes of three low-water-loss cementing compositions demorzstrate that the procedure results in relatively rapid development of strength and impermeability of the cement cake. Simulated squeeze-ceinenting tests made in the laboratory likewise corroborated the practicality of the procedure. The laboratory tests showed that a newly developed oil-emulsion cemerzting composition is more susceptible to acceleration of set than are modified cements containing high percentages of bentonite. The acceleration procedure has been used successfully in field operations. INTRODUCTION Nature of Problem In squeeze-cementing operations, a substantial amount of time is consumed in waiting on the cement to develop strength after it has been squeezed into the well. Frequently, an interval of 18 to 24 hours or longer is required for the development of strength sufficient to prevent failure of the cement during subsequent operations in the well. Reduction of this waiting-on-cement time offers appreciable savings both in time and in money. A particular type of squeeze-cementing operation to which an increasing amount of attention has been given is encountered in permanent-type well completion operations wherein perforations are to be squeezed off1. In this procedure, it is customary to pump the cement slurry down the tubing and out into the perforated section through a retractable extension pipe. Squeeze pressure is then applied, which forces the cement slurry into the perforations and causes the build up of a compact filter cake of cement within the perforations. The excess slurry remaining in the hole is then removed by reverse circulation. The extension pipe is then retracted, and, if a new interval is to be perforated, a perforating gun is run through the tubing. The newly perforated interval may then be tested by swabbing. In such operations, it has been customary to allow approximately 20 hours or so for hardening of the cement squeezed into the perforations. This time interval is usually measured from the time that the cement is reversed out of the hole to the time that subsequent swabbing is started. If the cement has not developed strength at the commencement of swabbing, the pressure differential caused by swabbing results in failure of the squeeze job. At the time that the work described in this report was initiated, particular consideration was given to the reduction of waiting-on-cement time in squeeze cementing by the permanent-type completion technique. Consequently, much of the experimental work was directed to this specific objective, though the process which was developed for acceleration of strength development has possible application in other than permanent-type completion operations. Method of Attack Although quick-setting cements

Jan 1, 1957

By J. H. Faulk

An examination is made of the various factors influencing drilling rate and drill bit life in various diameter holes. It is concluded that drill bits in the size range 4% to 6 1/4 in. can be used to attain substantially the some daily drilling progress as conventional size bits in soft rock drilling operations. An examination of the most important factors influencing "hazard of losing the hole" in the different hole size results in the conclusion that the smaller hole sizes can probably be drilled at reasonably low risk. However, this risk will be somewhat greater in the smaller diameter holes, requiring that special drilling and mud engineering practices be used to make small diameter holes practicable in soft rock drilling operations. An engineering analysia is made of the power and hydraulic requirements of several drill string-hole combinations to test the feasibility of drilling .small diameter holes in soft rock areas. Large econormies in rig power requirements appear possible by drilling .smaller .size holes in these operations. INTRODUCTION The industry now is re-examining the utility of small diameter holes in the light of substantial technical advances made in recent years. Faced with increasing cost of finding reserves and with proration after developing them, the industry must either develop methods of economizing or receive a lower rate of return on investments. Small diameter holes appear to involve an attractive method of economizing. Our objective is to determine if this is technically possible in soft rock operations. Soft rock, as used in this report, refers to those formations of a "drill-ability" corresponding to that of all Gulf Coast formations shallower than and frequently including much of the Eocene rock system. An important phase of technology which we shall examine is relative drilling rate and bit footage which may be obtained with various size bits. Rig operating efficiency, particularly as influenced by hazard, is also discussed in detail. The technical conclusions resulting from these examinations are used to develop sample drill string design and rig horsepower requirements for drilling holes as smaH as 4 3/4 in. and larger. The principal criterion used for the drill string design is that approximately the same daily drilling progress would be possible in all size holes in soft rock operations. This facilitates a comparison of rig size required for drilling the hole sizes in the range between 4 3/4 and 8 3/4 in. BROAD PROBLEM OF DRILLING RATE AND BIT FOOTAGE The three factors controlling daily drilling progress are: (1) drilling rate of bit while on bottom turning, (2) bit footage, and (3) rig operating efficiency. Let us look now at the first two of these factors. Drilling technology has progressed to the point that a semi-quantitative analysis of the effect of various operating variables upon these factors can be made. Those factors which apparently limit both drilling rate and bit footage for bits now in use are: (1) bit design, (2) weight on bit, (3) hydraulic cleaning capacity for bit cutting surfaces and hole bottom, and (4) rotary speed. (We neglect the effect of mud and formation properties because these factors arc the same for the various size bits.

Jan 1, 1957