Search Documents

Professor Somasundaran has given an excellent presentation of the numerous problems which remain to be solved before the selective aggregation of fine particulates is likely to see broad commercial application in the beneficiation of mineral fines. However it is useful, I think, to reiterate some of the major problem areas. The over-riding factor which has limited the development of selective aggregation techniques is that processes such as coagulation and flocculation tend to be inherently non-selective. Conditions which favor the aggregation of one kind of fine particles usually favor the aggregation of all kinds of particles. As Professor Somasundaran has pointed out, the state of aggregation of a fine-particle dispersion is primarily determined by the forces of interaction between the individual particles. In most systems, the dominant forces are: 1. van der Waals - London Dispersion forces between the particles themselves 2. electrical double layer forces 3. steric forces between adsorbed layers on the surfaces of the particles. The London Dispersion forces between like particles are always attractive, but for dissimilar particles dispersed in a fluid medium can, in some cases, lead to a net repulsion. Electrical double layer forces always lead to repulsion between like particles but can, again, cause either attraction or repulsion for dissimilar materials. The steric forces, which are by far the least understood of the three types, can also lead to attraction or repulsion depending on condi-

Jan 1, 1979

T.P. 1958 D. H. DAVIS.*-Mr. Carris has ably pre¬sented the problems of coal preparation, particularly those brought about as the result of increased mechanical loading. Many mines are now crushing the run-of¬-mine raw coal through 12 or 15 in. immediately after it is dumped from the mine car and before it is handled by conveyors. At certain mines the removal of large slate mechanically has been solved by the installation of scalping screens consisting of bars or rails set at spacing of 12 to 15 in. on the top deck of the main raw-coal sizing screen. At the plants where these are in use, the plus 12 or I5-in. raw material contains 60 per cent or more free rock or slate, so that it is easier to pick coal than to pick rock. After the screening at 12 or 15 in. is accomplished, the oversize material is diverted to one side of the shaker, where a picker allows the refuse to pass off the shaker into a chute and guides the coal back onto the shaker. After the large rock has been removed, it is then advisable to reduce the size of rock by crushing before putting it onto a conveyor. A great saving in picking labor has been made by the use of such scalping screens, which in addition has maintained the plant capacity when handling a dirtier feed. The great increase in percentage of coal under 1/4 or 3/8 in., coupled with a greatly increased percentage of free impurities in this size, is the most serious problem that has been brought about by mechaniced loading. Many plants that formerly prepared good quality 1/4-in. to o or 3/8-in. to 0 slack by air¬cleaning are faced with installing facilities for wet-cleaning mechanical and heat-drying and water clarification. The change to wet prepa¬ration of fines usually affects the marketing problems for many coal companies. There will also be problems involving wastage of fine solids and stream pollution. Much work will be necessary for improvements in present practice. Pneumatic and electrostatic methods for cleaning fine coal should receive consider¬able attention in an attempt to avoid wet¬cleaning of fines. The preparation supervisor and the plant personnel should not be satisfied merely to run the cleaning-plant machinery and assume that the job will be done for them. Coal is a heterogeneous substance and in many instances is constantly changing. This is more true when full-seam methods are in use. Only persons trained to observe closely and make the necessary changes in plant operation will be able to solve the many problems that will be imposed on the preparation plants. The plants will require skillful and observant operating men. With full-seam mining methods, seams of roof coal will often be mined. Under the former mining systems these strata were not mined and frequently they contain a high per¬centage of bony and banded partings. The mining of this coal will greatly alter the washability and specific gravity characteristics of the feed to the plant. Often the percentage of 1.40 to 1.60 sp. gr. increased from 3.5 to 7.5 per cent, or nearly a 1.0 per cent increase in the ash content of the 1.60 sp. gr. float coal. Thus the cleaning problem is much more difficult, and it is unlikely the same ash content of cleaned coal can be produced as before without a decrease in recovery or the produc¬tion of a "middlings" product. Mr. Carris had this in mind when he said "The quality of the

Jan 1, 1946

By C. F. de Mendonca, T. Kater, R. P. de Souza

The authors are to be commended for finding a material for pellets binding that we were unable to uncover during the investigations that led to US Patent No. 3,748,116, “Method for producing metallic iron powder from iron ore concentrate, ” July 24, 1973, by G.G. Reed, Jr., J.M. Karpinski, and S.V. Fox. This patent concerns a method of processing “super’ ‘-concentrates prepared from magnetite or “blue dust” into molding-grade metallic iron powder for use as a bulk commodity, in contrast to current methods which produce small batches that are custom-blended with additives and/or alloye to customer specifications. The one thing we had not found at that time was an organic binder (mineral-matter-free ) that would allow induration to produce hardened pellets that would survive SL/RN Direct Reduction. Peridur appears to provide this missing link needed for large scale (200 t/a, or 220,460 stpy) single line plant capacity consistent with a low market price to ensure greatly broadened use of metallic iron powder. I hope that industry will adopt this combination so that metallic iron powder usage can fulfill its potential

Jan 9, 1985

By G. G. Reed

G.G. Reed, Jr. The authors are to be commended for finding a material for pellets binding that we were unable to uncover during the investigations that led to US Patent No. 3,748,116, "Method for producing metallic iron powder from iron ore concentrate," July 24, 1973, by G.G. Reed, Jr., J.M. Karpinski, and S.V. Fox. This patent concerns a method of processing "super"-concentrates prepared from magnetite or "blue dust" into molding-grade metallic iron powder for use as a bulk commodity, in contrast to current methods which produce small batches that are custom-blended with additives and/or alloys to customer specifications. The one thing we had not found at that time was an organic binder (mineral-matter-free) that would allow induration to produce hardened pellets that would survive SL/RN Direct Reduction. Peridur appears to provide this missing link needed for large scale (200 t/a, or 220,460 stpy) single line plant capacity consistent with a low market price to ensure greatly broadened use of metallic iron powder. I hope that industry will adopt this combination so that metallic iron powder usage can fulfill its potential. ?

Jan 1, 1986

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By E. L. Fidler, T. E. Finch

Wayne Anderson Regarding the technical paper by Thomas E. Finch and Edward L. Fidler, "Recovery of Stray (Thin) Seams in Western Coal Mining." I would like to comment on this subject. In western Canada, most strip mines encounter thin seam coal or rider seams. Although the paper addresses the problems and costs associated with the recovery of this coal, it does not take into account what the savings are. Without looking at the savings, the "Total Objective" is of course not clear. I feel that in a stripping operation the mine can spend per ton (of the thin seam) up to their dragline stripping costs per ton to recover a rider seam or thin seam. The reasoning behind this is simply that this is the price the mine will have to pay to expose an equivalent amount of coal without the recovery of these thin seams. If the mine can recover a rider seam or thin seam for less than the dragline operating costs per ton, a savings will be realized. By recovering a thin seam or rider seam, the life of an ore body is extended by that amount of coal not thrown away. In addition, the cost of land acquisition, associated permits, capital, and reclamation will be reduced as more coal is delivered for a given area. When the above points are considered, the recovery of these thin seams can be very profitable and indeed worth recovering.

Jan 11, 1982

By Wayne Anderson

Regarding the technical paper by Thomas E. Finch and Edward L. Fidler, "Recovery of Stray (Thin) Seams in Western Coal Mining." I would like to comment on this subject. In western Canada, most strip mines encounter thin seam coal or rider seams. Although the paper addresses the problems and costs associated with the recovery of this coal, it does not take into account what the savings are. Without looking at the savings, the "Total Objective" is of course not clear. I feel that in a stripping operation the mine can spend per ton (of the thin seam) up to their dragline stripping costs per ton to recover a rider seam or thin seam. The reasoning behind this is simply that this is the price the mine will have to pay to expose an equivalent amount of coal without the recovery of these thin seams. If the mine can recover a rider seam or thin seam for less than the dragline operating costs per ton, a savings will be realized. By recovering a thin seam or rider seam, the life of an ore body is extended by that amount of coal not thrown away. In addition, the cost of land acquisition, associated permits, capital, and reclamation will be reduced as more coal is delivered for a given area. When the above points are considered, the recovery of these thin seams can be very profitable and indeed worth recovering.

Jan 1, 1983

By S. C. Sun

This article by Spokes and Mitchell de- serves high commendation. For many years mineral dressers have been at a loss to explain the variation in magnetic susceptibility of the same mineral species obtained from different localities. In fact, they do not even have a list of accurately measured data on the specific magnetic susceptibility of weakly magnetic minerals to consult. Experience as a university teacher has firmly convinced me that the average student has more difficulty in acquiring a satisfactory knowledge of magnetism than of any other branch of mineral dressing. This is almost entirely because the subject has been treated far too much from a strict practical standpoint and far too little from a fundamental one. It is no exaggeration to state that almost all the published theoretical discussions are based on the experimental results of manufactured chemicals and alloys, but not of naturally occurring minerals. In an attempt to remedy this state of affairs, the author of this article not only set up a new magnetic balance in the Department of Mineral Preparation of The Pennsylvania State University, but also performed work of fundamental value, thus pointing the way to further research. This is evidenced by the fact that an investigation of the magnetic susceptibilities of manganese minerals was recently completed by S. G. Watt under the direction of David R. Mitchell, now acting dean of the College of Mineral Industries of the Pennsylvania State University. D. J. Cook is studying the magnetic susceptibility of titanium minerals under my supervision. It is hoped that our research program can be continued for several years and that similar investigations will be Initiated at other universities and research institutions.

Jan 4, 1958

I do not regard the criticism by Rankin of my work as valid or even meaningful. I strongly reject the assertion by Rankin that my results are invalid. As stated in my paper, the equation to solve (in e. m.u. ) is: [ ] where n2 =4 ps? . This may be rewritten as three scalar equations in Cartesian coordinates, one of which is [ ] The equation to be solved is the diffusion equation, and it is not appropriate to consider waves in this context. In the method a point-wise solution to the problem is approximated. As discussed in my paper the approach taken at discontinuities in conductivity is to choose the normal component of [E] at the discontinuity as the average of the normal components on either side of the discontinuity. This is similar to the well-known assumption made in obtaining Fourier series representations for piecewise continuous functions (Pipes, 1958; p. 51). In the geophysical problem this means that the discontinuity is approximated by a transition zone, which is a very good approximation for such cases. By using this approach, both the values of the function and its derivatives give a good estimate for those associated with the physical situation. It is not apparent and Rankin has not shown that "all the field components and the derivatives are grossly distorted in the region about the boundary" for geophysically realistic situations. He has given no evidence to support his assertation that the results are "invalid". Although Rankin declares that one cannot calculate the electric components from the magnetic, in his discussion he has not stated why this is so. After once calculating the magnetic components the electric components may be calculated, but one must insure that the initial solution is accurate enough to prevent significant round-off errors.

Jan 1, 1973

Contribution by W. Assibey-Bonsu I congratulate Mr N.O. Lotter on his paper. There are two main aspects of the paper on which I would like to comment. One aspect is his review of P. Gy's sampling theory under the heading 'Sampling the mill feed' (p. 153). The other aspect relates to his reference to one of our papers1 that was published in the Journal (p. 152). My comments on the former will be given elsewhere'. Authors' reply: Dr Assibey-Bonsu's contribution to the subject is appreciated.

Jan 1, 1996

By A. K. Bhasin

A. K. Bhasin, (Development Engineer, Marcona Corp., San Francisco, Calif)-The author suggests the use of the term "consistency" for apparent viscosity and accordingly calls his viscometer a "consistometer." However, he goes on to refer to "consistency" as a combination of plastic viscosity, yield stress, and stability (p. 104, col. 2, line 6). Unfortunately, such conflicting terminology is encountered too often in rheological

Jan 1, 1973

By Douglas R. Piteau

Douglas R. Piteau (Engineering Geologist, De Beers Corp., Kimberley, South Africa; Presently Consulting Specialist at Nchanga Mine Open Pit, Chingola, Zambia)-Mr. Lutton is to be commeneded on his analyses and presentation of such practical data which can be used for predicting a preliminary optimum slope angle in rock. It appears that he assumes all slopes analyzed to be straight. Although there are overriding factors which affect the general slope configuration, such as structural discontinuities, ground water, and other environmental factors such as weathering conditions, regional stress, etc.,8 the affects of plan geometry under certain conditions also can be of outstanding importance. In investigation of natural slopes, for example, the effects of plan geometry are not entirely appreciated and it is in this respect that discussion is given. Experience in southern Africa has shown that the overall geometry of surface openings in rock, particularly those with dimensions of the order of 1500 ft or less, i.e., where radii of curvature of the slopes are less than, say, 700± ft, must be considered in rational slope-stability analyses. That is, the slope angle is not only a function of slope height, strength of the mass, and geometry of structural discontinuities, but also is dependent upon the plan geometry of the local slopes and the plan shape of opening. Technically speaking, adequate analysis of the slope must be three-dimensional, the third dimension being that of overall plan configuration and the analysis must incorporate its subsequent effects. However, current theories of slope stability all deal with the slope as a two-dimensional problem, i.e., a slice of unit length of an infinitely long slope is considered for a condition of plane strain. In this the tacit assumption is made that the plan radii of the crest and toe of the slope are infinite and no attention is given to the plan geometry of the slope. Clearly this is not the condition encountered in practice, particularly in open pit mining where excavations, relatively speaking, can be small and where these radii of curvature accordingly can have important affects on the slope stability. This is illustrated by the analyses of Piteau and Jennings 9 of the natural slopes which had developed around pipes of four diamond mines in the semiarid Kimberley area of South Africa. Although these slopes consist of dolerite overlying shale, the values of the slope angles of all the pits were corrected for a height of slope of 320 ft assuming that no dolerite occurred. This brought the data onto a comparable basis. These data were analyzed statistically and a clear empirical relationship, as is shown [in Fig. 4], is seen to have formed between angle of slope and curvature of slope, i.e., the angles of slope are greatest where the radii of curvature are least. Also, it can be seen that the slope of each line is different, indicating that the plan shape of the open pits also are significant, the curve being steepest for the open pits which are more circular in shape in contrast to those which are more elongated. The effect of slope curvature on the average angle of slope for the two extreme radii of 200 ft and 1000 ft for all four open pits is 39.5° and 27.3°, respectively. Hence, the concave curvature effect represents an average increase in slope angle of 12.2° from the essentially straight slope. In quantitative terms in Mr. Lutton's Fig. 2, this represents displacing the curve for a 320-ft pit from the second curve from the bottom (i.e., shale in subtropical climate) to that of the third from the bottom (i.e., quartzite in temperate environment).

Jan 1, 1972

By A. W. Khair, S. S. Peng

Discussion by J. Parker Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa(4000 and 7000psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic'? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition of moisture, from sprays or from humid air? Did moisture weaken the rock? Did it cause the rock to expand quickly, thus to induce internal compressive stress? How can the near-vertical cutters, as shown in the photographs, be attributed to primarily horizontal stresses? Did the cutters follow any particular pattern in the development panels, which might be related to a particular stress pattern? For example, did they always appear alongside the stiffest pillar? Or always along the northwest rib? Was there any evidence of the pillars and entries "rotating" under the influence of differential horizontal stresses? How much did the entries and pillars rotate as the longwall face approached and passed? After rooffalls, did the openings assume shapes which would indicate a preferred shape in that stressfield and geology? Did crosscuts always survive without damage, as shown in the sketch?

Jan 1, 1992

By John Dasher

Extrapolation is a useful technique, but it can be overdone. Seldom is it justified to study over a range of 1 to 6 and extrapolate the results to 150,000. It is especially dangerous if the extrapolation is based on a false assumption. The authors assume settlers scale-up by residence time rather than by area, admit their result (a settler depth of 7 m) is "unreasonable" and suggest longer, wider, shallower settlers might be better. Various authors have noted for a copper-LIX system a total flow basis of 2 gpm per sq ft for sizing settlers. The results of this are compared with those in the paper in [Table 7]. The authors note that flooding of their settlers was never approached. Thus the smallest unit calculated is understandably twice too big. The largest however, is 5% of the required size. I note that the figures in [Table 6] for 1/min/cm2 are based on plan area rather than cross section as titled and are wrong by l0 4. A flow of 2050 1/min/cm2 is about Mach I. It is also 10 5/3 or 46.5 times that of the little one, although the abstract says the design was based on constant flow rate per unit cross section.

Jan 1, 1977

By John Dasher

Getting spodumene to float quickly and cleanly can be a problem. The author has presented an excellent account of a valid and useful approach to the scale-up of such problem floats. This indicated advantages for doubling retention time, i.e., buying another set of flotation cells. The author states that 21 pct of the spodumene floated in 2 min in the laboratory cell, that the grade of the rougher was about 75 pct spodumene, and that the final tailing contained 4 to 12 pct spodumene in different sizes with the present cells and 1 to 9 pct spodumene with twice as many cells.

Jan 6, 1959

This excellent paper by Dr. Colombo parallels quite closely the bench and pilot work done by the Hanna Research Laboratory on the Mesabi oxidized taconites. Because of the vast reserves and future ore requirements the need to perfect the selective flocculation-flotation process becomes very necessary. The selective flocculation process is a very efficient method of desliming, leaving a fairly clean, upgraded product for flotation. However, one of the problems that we have encountered in this process was some very fine, -2 micron liberated goethite in the slimes that did not flocculate. The complete slime removal is not necessary. We remove slimes to the extent of about 5% of the iron units. However, on difficult treating ores we would remove more slimes. The reclaimed water from our pilot plant has a turbidity of about 1000-3000 ppm. We can obtain lower turbidity water but to do this would involve additional lime as a tailing flocculant and we would run the risk of flocculating the entire ground pulp in the selective flocculation process because of the increased Ca level in the water. We have about seven different geological ore types out of 17 recognizable ore types that are treatable. All of these ore types require different degrees of dispersion and grinding which is a problem. The use of acrylic acid polymers as a selective flocculant has been patented by the American Cyanamid Co. This will-have to be

Jan 1, 1979

This excellent, concise paper by Dr. Iwasaki on the principles of selective flocculation for iron ores discusses many of the principles and problems which have occurred in our bench and pilot plant test-work. The use of sodium tripolyphosphate in combination with sodium silicate as a dispersant is very effective. However, this may cause a problem with the environmental groups as phosphorous is a nutrient. We have also established that the lower the Ca level in the pulp solutions the greater the dispersion. We have found that ores from the same geological strata, having the same general mineralogy and iron content will sometimes have widely different degrees of dispersion. There was-no difference in the gross mineralogy but the solubility of the Ca and SO ions was much less in the ores most easily dispersed. Research efforts should be directed towards a more practical means which would more easily enable one to predict the amount of dispersant required for the various ores. With regard to water quality we have found that waters having higher contents of SO4 and C1 ions hinder dispersion. This could be a method of controlling too much dispersion by the addition of sulfate or chloride ions. This would require further investigation. We have had no trouble with agitation speeds of up to 925 rpm in conditioning starch with the dispersed pulp prior to selective flocculation. We have found about 0.3Lb/LT of starch to be sufficient for selective flocculation on our ores. The increasing of the starch to 1.25Lb/LT has had no effect on the metallurgy of the selective floccula-

Jan 1, 1979

Insoluble slimes are present in nearly all sylvinite ore bodies and must be removed prior to potash flotation because they adsorb excessive amounts of potash flotation reagents and cause low potash recoveries and grades. The problems associated with insoluble slimes will become more pronounced as high grade-low insol potash ores are depleted and lower grade ores containing high insols are processed. The most common commercial practice for insoluble slimes removal is mechanical desliming (hydroclassification); however, most of these desliming circuits were designed to treat sylvinite ores containing less than 4 percent insoluble slimes. As Mr. Banks mentioned in his presentation, higher insoluble slimes concentrations (>4 pct) in the mill feed overtax the mechanical desliming circuit and result in excessive brine and potash losses. Increasing the capacity of the circuit would require redesigning of the entire potash circuit and additional costly equipment. Because of mineralization and liberation properties of the high insols sylvinite deposits, the expansion of the desliming circuit may not economically maintain high potash grades and recoveries. Selective flocculation-flotation is an excellent alternative for removing insoluble slimes from potash ores. Cominco's ore, containing 4.5 to 8 percent insoluble slimes, is particularly amenable to the slimes flotation process, probably because of the absence of expanding-type clays such as montmorillonite. The overall potash recovery of 86 percent and low slime flocculant and collector dosages of 0.03 to 0.04 pound reagent per ton of feed is good evidence of the success of the process. If appreciable montmorillonite were present, the metallurgy would not be as favorable and reagent consumptions would increase significantly.

Jan 1, 1979

My question relates to tundish nozzle plugging on aluminum-killed heats. North Star has avoided this problem by silicon deoxidation. What has been Inland's experience with this problem on open-pour and submerged nozzle pouring?

Jan 1, 1972

The evaluation of suppliers of BOP linings included only magnesitic and periclase compositions. Ford utilizes some dolomitic compositions. Do you care to comment on this subject?

Jan 1, 1972