Search Documents

By Oliver Bowles

Dimension stone is a term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, contrasted with crushed, broken and pulverized stone covered in another chapter. Dimension stone includes cut stone, rough building stone, ashlar,* rubble, monumental stone, paving blocks, curbing, flagging, and many types of ornaments and novelties carved from stone. Riprap-large, irregular blocks used for shore protection-is classed with crushed and broken stone. Composition, Varieties, and Properties Dimension stones are of many kinds. The principal varieties are granites, trap rock (diabase, basalt, and gabbro), sandstone, limestone, and marble. Slate is covered in a separate chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. The basaltic rocks are darker in color than the granites. They contain little or no quartz and consist largely of plagioclase feldspar, augite, pyroxene, and hornblende. They are classed commercially as black granites. Limestone consists essentially of calcium carbonate. Dolomites and magnesian limestones used as dimension stone are classed with the high-calcium limestones. Marble is a crystalline form of limestone, but in the trade, any carbonate rock which will take a polish is called a marble. Many limestones which are fossiliferous but which will take a polish are sold as a decorative stone for lobbies of hotels and office buildings. Sandstone consists essentially of silica in the form of sand grains cemented into a coherent mass. Although rock occurrences are numerous and widespread, the exacting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced joints or planes of weakness can be used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive colors or color pattern, and freedom from impurities that may cause stains or deterioration usually are demanded. Hardness is a variable property. Granites and diabases are as hard as or harder than steel, while limestones and marbles may be scratched with a knife. The hardness of sandstone depends upon the degree of cohesion of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except where stones are subjected to abrasion as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains. Stones are of many colors and thus can satisfy a variety of tastes. For monumental stone, a marked contrast between polished and tooled surfaces is preferred in order that inscriptions may be read easily. Strength requirements usually may be disregarded because any sound structural stone suitable in other respects is almost invariably many times as strong as would be required for any ordinary use. The pressure on the base course of the Washington Monument, Washington, D. C., is less than 700 psi, and highgrade granites, limestones, sandstones, and marbles will sustain a crushing load of 10,000 to 25,000 psi. A structure made of stone with a crushing strength of 15,000 psi would have to be nearly 21h miles high before crushing of the lower courses would occur. However, stone disintegrates more readily under severe

Jan 1, 1960

By Oliver Bowles

DIMENSION stone is a convenient term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, as contrasted with crushed, broken and pulverized stone, discussed in another chapter. Dimension stone includes cut stone, rough building stone, ashlar, rubble, paving blocks, curbing and flagging. Riprap-large, irregular blocks used for shore protection-is classed more properly with crushed and broken stone. COMPOSITION, VARIETIES AND PROPERTIES Stones used as blocks or slabs are of many kinds. The principal varieties are granite, sandstone, limestone and marble. Slate is covered in another chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. Limestone consists essentially of calcium carbonate, with which may be associated certain impurities such as clay, sand, or iron oxide. Dolomites and magnesium limestones used as dimension stone are classed with the high- calcium limestones, as they are used in the same way. Marble is a crystalline form of limestone. Sandstone consists essentially of silica in the form of sand grains cemented together into a coherent mass. Although rock occurrences are numerous and widespread, the ex- acting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced cracks, lines of weakness, or joints can be so used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive color, and freedom from impurities that may cause stains or deterioration usually are required also. Hardness is a variable property. Granites are as hard as or harder than steel while limestones and marbles may be scratched easily with a knife. The hardness of a sandstone depends upon the degree of cementation of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except when stones are subjected to severe abrasion, as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains.

Jan 1, 1949

By L. P. Meade

Dimension stone and salt are two of the oldest industrial minerals utilized. Salt has been and still is a necessity to the well being of man. Dimension stone on the other hand has been utilized by man to glorify conquests - both in the battlefield and corporate arena. Both commodities are important, but dimension stone has an additional use in that the survival lessons learned by the domestic industry can be applied to other contemporary industrial minerals, Specialization in the market place and customer service have allowed domestic producers to survive: subsidized foreign competition, obsolete equipment, and lack of capital.

Jan 1, 1986

By G. M. Schwartz, G. A. Thiel

THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snelling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipestone and elsewhere in southwestern Minnesota: The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation, in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowled and by Thiel and Dutton.2 The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.3 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on' the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1-Central Minnesota in the region of the city of St. Cloud, 2-the upper Minnesota River valley region, 3-the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in. their dis-

Jan 1, 1952

By Stephen P. Case, Stephen Castellucci, William Parsons

In this paper, the authors present a step-by-step discussion of dimension stone production at a New England granite quarry. The quarry mines a rare pink granite which is used for facings and panels in the construction of high rise buildings around the world. The discussion includes geological considerations, block layout, drilling, explosives loading, block handling, and mobile equipment utilization.

Jan 1, 1990

By I. Ashmole

The dimension stone industry is not widely known or appreciated within the mainstream mining industry. This is in spite of the fact that the industry has grown at an average of over 7% per annum since 1980, and is estimated to now have a global turnover in excess of US$ 60 Billion per annum. Production technologies, particularly in the developed world where labour costs are high, have developed rapidly over the past two decades. Aligned with this, there has been a significant trend in adoption of a more professional mining approach in the exploration for and operation of dimension stone quarries. In fact, in the experience of the authors, mining a dimension stone deposit successfully if often more challenging from a mining engineering point of view than many conventional surface mines. This paper gives an overview of the industry and then proceeds to discuss best practice in exploration for dimension stone and to outline the latest technologies applied in mining of dimension stone. These technologies are varied and the specific combination of technologies applied in any given quarry is determined by both the physical properties of the material as well as the influence of geology which significantly impacts on the recovery of saleable material and hence the economics of the quarry.

Jan 1, 2008

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By V. J. Ramirez, A. M. E. Noguez, M. J. Navarrete, B. G. Salas, N. T. Robert

"The close die forging stress in truncated conical cavities is evaluated with dimensional analysis. Five dimensionless groups are proposed from the process variables in order to simplify the forging stress determination. These groups are experimentally related and graphically expressed. This methodology can be used to predict the actual forging stress in industrial close die forgingThe use of the dimensionless groups allow to comprise more cases than the presented here, provided similar geometries and operational conditions.Introduction.Closed die forging is essentially a plastic deformation inside a two piece mold (forging die) with the inverted shape of the actual forging geometry. This plastic deformation will always be the result of a compressive stress. There are theoretical models which include complex calculations for the analytical determination of stresses (1, 2, 3, 4). Results of these calculations are approximate, requiring generally ulterior tests to obtain the true operational conditions(5).In this paper, it is presented a simplified approach to the actual compression stress needed in the forging. A well known tool in engineering: the Buckingham's Pi theorem in conjunction with dimensionless groups and a working piece scale model is used. Dimensional analysis will give the dimensionless terms needed to experiment with a selected scale model geometry to make the stress determination. The results presented demonstrate the reliability of this methodology."

Jan 1, 1997

By W. B. Lewis, M. E. True, M. C. Leverett

Tars paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, perm ability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of sell completion and the effects of various factors on recovery of oil from layered sands.

Jan 1, 1942

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992

By N. Arbiter

The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter ratio. This is in spite of the fact that practice varies substantially in this area: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia; historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to/the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills; on the occurrence of the overload phenomenon; and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape face or is of major importance in this area; and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type.

Jan 1, 1990

By José Cuadros

"El presente trabajo describe la aplicación del ""método gráfico de estabilidad"" como herramienta de diseño en el dimensionamiento de tajeos a través de técnicas geomecánicas que pueden ser aplicadas en otros yacimientos con similares condiciones que la mina Chupa a fin de mejorar la productividad y y mantener adecuadas condiciones de estabilidad de las excavaciones. En consecuencia, el dimensionamiento de los tajeos de Chupa fue uno de los varios trabajos que la Empresa Minera Iscaycruz S.A. realizó para el inicio de la explotación de este yacimiento a través del método de minado “tajeos por subniveles” con la utilización de taladros largos, sostenimiento con cables y relleno cementado. "

Sep 13, 2001

By Samuel Canchaya Moya

Si bien en las últimas décadas se aplicó el estudio de la geoestadística en la minería, el uso de la técnica no ha logrado una mayor difusión. En ese sentido, el presente texto señala la aplicación de los paquetes de software en la minería a través de los módulos de geoestadística. En este punto, la optimización del muestreo, se convierte en un problema tanto en la etapa de exploración como de producción. Por ello, es necesario conocer y comprender los conceptos y métodos geoestadísticos que se apliquen a la medida de muestreo de la veta, ver distancia y ubicación de taladros, costos de campaña de exploración, entre otras medidas, etc.

Jul 31, 2003

By J. Mácsik, J. Lindblom, C. Maurice, Susanne Nigéus

Using non-hazardous industrial residues in mine waste remediation is beneficial not only for the mining industry where substantial amounts of the waste generated have potential to produce acid rock drainage and pollute the environment, but also the providing industry, minimizing the waste landfilled. In this study green liquor dregs (GLD), residue from 15 different paper mills were characterized to valorize it as a potential product as a cover material. In another part of the study, one of the GLDs and a local till were characterized to determine the optimal mixture of GLD amended till to be used in a field application at the closed Näsliden Mine in northern Sweden. The study concluded 10% GLD-amended till to be the optimal recipe and was successfully applied at the Näsliden mine waste dump. However, the great variability in the characteristics of GLD creates challenges if it is to be valorized as a product.

Dec 7, 2023

By P. Wittke-Gatterman

ABSTRACT: A three dimensional constitutive law for swelling rock is presented. It can be applied to the osmotic swelling of mudstone as well as to the swelling of rocks containing anhydrite. It describes the development of time-dependent strains and stresses due to swelling considering elastic and viskoplastic behaviour. Furthermore an anisotropic swelling behaviour can be considered. This constitutive model was implemented within a numerical computation program according to the finite element method and calibrated on the basis of the results of measurements in the investigation drift of the Freudenstein tunnel which is completely located in the unleached Gypsum Keuper. A parameter combination could be found which results in a good agreement between numerical solutions and results of measurements. Therewith an analysis procedure which enables the design of tunnels in swelling rock is available. ZUSAMMENFASSUNG: Im vorliegenden Beitrag wird ein dreidimensionales Quellgesetz vorgestellt, das nach derzeitigem Kenntnisstand sowohl auf das osmotische Quellen von Tonsteinen als auch auf das Quellen anhydrithaltiger Ton- beziehungsweise Schluffsteine anwendbar ist. Das Stoffgesetz wurde in ein Finite-Elemente-Programm implementiert und anhand von Meßergebnissen des im unausgelaugten Gipskeuper liegenden Untersuchungsstollens des Freudensteintunnels kalibriert. Es ist gelungen, eine Kennwertkombination zu finden, mit der alle Meßergebnisse gut beschrieben werden können. Damit steht ein Bemessungsverfahren für Tunnel in quellfähigem Gebirge zur Verfügung. RÉSUMÉ: Dans l'article présent un loi de gonflement à trois dimensions est présenté, qui peut être appliqué aussi bien au gonflement osmotique de l'argile compactée q'au gonflement de l'argile compactée ou du limon compacté contenant de l'anhydrite. Le loi de comportement était implémenté dans un programme numérique d'éléments finis et calibré avec des résultats de mesures de la galerie de recherche du tunnel de Freudenstein, situé dans le Keuper de gypse non lessivé. On est réussi à trouver une combinaison de paramètres avec laquelle tous les résultats de mesures peuvent être bien décrits. Par ce moyen, une méthode de dimensionnement existe pour des tunnels dans de la roche capable de gonfler.

Jan 1, 2003

By V. Ogarlaci

Over 90% of the Romania's lignite reserve is located in the region of Oltenia, which is why this area is given special attention in the country's coal resources. Because the lignite deposit of Oltenia is comprised of 1-8 exploitable coal layers, their capitalizing calls for urgent arrangements to ensure rational exploitation under conditions of total safety, minimum losses and efficiency. The technology used the coal pits of North-Western Oltenia is the technology of excavation, transport and dumping in a continuous flow by using the complexes of excavation, transport and high-capacity dumping. The theme of this paper is of particular importance because the rhythmic operation in complete safety, is necessary both for sizing and keeping within the bounds of acceptable values, throughout the process of excavation of the geometric elements of the coal faces, marked by: the height of benches, slope angle and width of berms. Geometric dimensions of the benches of the open pits, the height of benches, slope angle and width of berms shall be calculated and shall be based on: the massif structure that forms the benches; physical-mechanical characteristics of rocks from the bench; working conditions, characterized mainly by mining and extraction methods applied; functional parameters of the mechanical equipment used to perform various operations on the coal face etc. For this study it was necessary a broad field for task tracking, measurement, research and design elements of the coal face, for land survey and a desk activity by: processing of topographic data, laboratory analyses on physical and mechanical properties of rocks and numerous specialized studies. In the final part, we bring some contributions to elucidating the issues of special importance for the lignite coal pits of Oltenia, coming up with data, graphics, formulas, solutions and concrete dimensioning of coal faces in terms of using technology in a continuous flow.

Aug 1, 2013

By R. Hurman Eric

The flow of molten slag and matte and the estimation of the mass of settled matte in electric furnaces is discussed and the action of the electric furnace as a settler is considered. Particle size of the concentrate and its grade are major contributors to settler dimensions. Discussion on the production capacity of the electric furnace with reference to operating current, power input, furnace dimensions such as width and length and electrode diameter are given. These discussions are based on considerations derived mainly from experimentally determined properties of the slag such as its resistivity, viscosity and liquidus temperature. Extension of the design and operating considerations to circular furnace symmetry is also discussed.

Jan 1, 1995

By R. Hurman Eric

The electrode in a slag-resistance electric furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power, i.e. heat needed for the operation. The control parameters are the size and positioning in the slag bath which are defined by slag resistivity, furnace resistance, cell constant and power input sequence all of which are closely interrelated. The flow of heat generated by the electrode current determines the energy distributions and thus the furnace dimensions. Heat flow models concerning vertical, horizontal and combined two-dimensional flows are discussed. All these considerations are based on the experimentally determined slag properties such as its resistivity.

Jan 1, 1995

By Richard H. Mote, W. C. Schroeder

The endlessly changing pattern of mineral supply and demand offers opportunity to the alert and can bring disaster to the unwary. The discovery of ore bodies, the invention of extractive processes, the provision of new transport facilities, the political stabilization of underdeveloped areas, and many other changes can increase supply dramatically. Such new outpourings of mineral wealth from ore bodies bring fortunes to their developers, and consumers frequently find their competitive positions decidedly improved by new and cheap sources of supply. On the other hand, operators of marginal properties can find competition from newly opened high-grade mines intolerable. Consumers that have depended on the products of nearby, high-cost mines may find new, remote, low-cost supplies advantageous only to their competitors. The invention of new prospecting methods can have spectacular effects. Shortly after World War I the discovery rate of petroleum pools began to decline. The leading prospecting technique of that day, the projection downward of surface reflections of geologic structure, was proving less rewarding. Prophets foretold an oil shortage in the near future. But at that very moment scientists were perfecting the application of seismic waves to reveal underground oil-bearing geologic structures. As these geophysical methods were put into commercial use the whole outlook changed-the problem of the 1930's became how to cope with the surplus from discovery, not how to meet the ever rising demand. Many lead mines were being abandoned as unprofitable about this same time because the penalties charged by smelters for the zinc in the ores and concentrates more than counterbalanced the payments for lead and silver. Then selective flotation (at the time called differential flotation) appeared,

Jan 1, 1959