Search Documents

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

  Underground positioning and communication are essential technologies for the future of underground mining operations. In contrast to other positioning and communication technologies such as wireless local area network (WLAN) or radio frequency identification (RFID), ultra-wideband (UWB) radio technology provides significant benefits like accurate and robust positioning of mobile machine equipment, which is indispensable for future autonomous systems in underground mining processes, such as production, transportation and auxiliary operations. Among these technologies, UWB offers many advantages, including higher accuracy, robustness, resistance against noise and multipath effects, and low power consumption [1,2]. Underground automation and localization systems benefit from these advantages and use the technology to improve efficiency and safety. There are many studies being carried out on this technology to increase the results’ accuracy, energy sufficiency and more. Two robust UWB modules that were developed for underground positioning and collision avoidance with regard to human safety in underground mining operations are introduced. The measurement results of tests carried out in an underground mine are discussed as well to confirm the functionality of the system.

By Lloyd B. Underwood

In the event of a sudden nuclear attack upon the United States, it is imperative that vital command and control centers have a high probability of survival. One such vital facility is the North American Air Defense Command Combat Operations Center at Colorado Springs, Colorado. Known briefly as NOW, this installation when completed will be housed in large chambers excavated out of granite beneath the eastern slope of Cheyenne Mountain (Figure 1). The NORAD COC, a U. S. Air Force sponsored project, will serve as the primary collection and evaluation center for data concerning unknown aircraft, missiles, or space vehicles, which might bring destruction to North America. The data will be fed into high-speed computers and electronic equipment from outpost sources - radar, ballistic missile early warning stations and picket ships throughout the world. Electronically controlled display boards will make it possible to evaluate the tracking data instantaneously and to take appropriate defensive action1.

Jan 1, 1965

By J. Lyndon Rosenblad

This chapter describes the development of a rocklike model material for use in tests with a rock-blocks model to investigate the failure mechanism of a discontinuum. In order to provide reliable results, the model material must be characteristic of natural rock and obey the laws of similitude. Initially, the development of such a material does not appear to be a difficult problem. Only when one undertakes such a task does he realize how little is actually known, and that there is considerable work yet to be done. A material that simulates rock in all of its physical properties probably will never be developed. There is now and probably always will be room for improvement. Improvement is needed not only in the component materials but also in the technique of preparation. The material developed and subsequently described in this chapter simulates rock in general and a schistose gneiss rock in particular. The material possesses many rocklike physical properties not found in previously used model materials. One of the most significant improvements of this material is that there is an increase of Young's modulus with an increase in confining pressure as determined by triaxial compression tests. A change in the usual procedure of material preparation was used to develop this material and is also described. MODEL MATERIALS USED IN THE PAST Intact Materials Numerous materials have been used by investigators in models in the past to simulate a wide range of prototype materials. Some of the materials used include cork, plastic, concrete, plaster of Paris, portland

Jan 1, 1972

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the NIOSH-designed roof bolter canopy air curtain (CAC) has gone through many iterations demonstrating successful dust control performance under controlled conditions. J.H. Fletcher & Co. (Fletcher), an original equipment manufacturer of mining equipment, has further developed the CAC concept by incorporating it into the design of its roof bolting machines. A new CAC design has been developed incorporating the results of testing of the NIOSH design and the recent Fletcher design. Observations from smoke testing conducted on this new CAC design in a laboratory setting show promise for improved performance. INTRODUCTION Exposure to respirable coal mine dust can cause coal workers’ pneumoconiosis (CWP) otherwise known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit (on an MRE basis) for respirable coal mine dust is 2.0 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities [30 CFR 70.100 2015]. Recently enacted legislation changes this standard beginning in August 2016 to 1.5 mg/m3 for a full working shift [Federal Register, 2014]. If the respirable coal mine dust contains more than 5% silica, the applicable respirable dust standard is reduced; calculated as 10 divided by the percent quartz present [30 CFR 70.101] so that the effective exposure limit for respirable quartz is 0.1 mg/m3 for a full working shift. Sources of exposure to respirable coal mine dust for the roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind (in the return air) of the continuous miner [Goodman and Organiscak, 2003]. Recent studies have demonstrated that vacuum dust collection systems are effective in capturing bolter-generated dust, if maintained and operated correctly and if proper face ventilation techniques are used. However, most exposure to respirable coal mine dust for the roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner [Potts et al., 2011; Colinet et al., 2013]. Because of this higher exposure downwind of the continuous miner, the roof bolter is generally limited to working downwind of the miner only once during a production shift"

Jan 1, 2016

By W. R. Reed, G. J. Joy, B. Kendall, A. Bailey

"Testing of the roof bolter canopy air curtain (CAC) designed by the U.S. National Institute for Occupational Safety and Health (NIOSH) has gone through many iterations, demonstrating successful dust control performance under controlled laboratory conditions. J.H. Fletcher & Co., an original equipment manufacturer of mining equipment, further developed the concept by incorporating it into the design of its roof bolting machines. In the present work, laboratory testing was conducted, showing dust control efficiencies ranging from 17.2 to 24.5 percent. Subsequent computational fluid dynamics (CFD) analysis revealed limitations in the design, and a potential improvement was analyzed and recommended. As a result, a new CAC design is being developed, incorporating the results of the testing and CFD analysis.IntroductionExposure to respirable coal mine dust can cause coal workers’ pneumo-coniosis (CWP), also known as black lung. If silica is present in the dust, the miner may develop silicosis in addition to CWP. CWP and silicosis are occupational respiratory diseases that are ultimately fatal and have no cure. The only method of prevention is to eliminate exposure to respirable coal mine dust and crystalline silica, or quartz. The occupational exposure limit on a Mining Research Establishment (MRE) basis for respirable coal mine dust had been 2 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities. Under recently enacted legislation, this standard was changed in August 2016 to 1.5 mg/m3 for a full working shift (The Office of the Federal Register, 30 CFR 70.100, 2015). When respirable quartz is present, the mine must maintain its average concentration at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percentage of quartz present (The Office of the Federal Register, 30 CFR 70.101, 2015).The sources of exposure to respirable coal mine dust for roof bolting occupations include infrequent maintenance and cleaning of the vacuum dust collection system and operating the bolter downwind — in the return air — of the continuous miner (Good-man and Organiscak, 2003). Recent studies have demonstrated that vacu-um dust collection systems are effective in capturing bolter-generated dust if maintained and operated correctly and if proper face ventilation techniques are used. However, most expo-sure to respirable coal mine dust for a roof bolter occurs when the roof bolter machine is operated downwind of the continuous miner (Potts, Reed and Colinet, 2011; Colinet, Reed and Potts, 2013). Because of this higher exposure downwind of the continuous miner, the roof bolter is often limited to working downwind of the miner only once during a production shift."

Jan 1, 2017

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

By M. Gonzalez Fernandez

"Commercially introduced in 2004, the SAGDesign™ test has today proved its efficiency for sizing SAG mills for a wide variety of ores, from very soft to very hard ones. The interest of building a model using the SAGDesign™ test specific energy is the introduction of such a model into a complete process simulator making it possible to predict a complete material balance. The developed model compares the required specific energy with the energy provided by the mill. This energy calculation is derived from the Austin Power Formula. The specific energy provided by the test is corrected, using various parameters, such as the Ball Mill Work Index, to take into account the true operating conditions, the feed and product sizes. The core of this model allows the determination of the product d80 using the mill geometry, its operating conditions and of course the SAGDesign™ test results. To be included in a simulator, the model must also predict the overall size distribution of the SAG mill discharge. Assumptions to answer this point are presented here. The model has been implemented in the USIM PAC simulator. It is used either to predict the product size distribution for a given SAG mill, but also to size a SAG mill for getting a required reduction ratio. INTRODUCTION Over the last few years several types of new comminution machines have been introduced in the market. The most notable newcomer was the HPGR (Morley, 2006). But, even when these machines have some advantages, they have not earned the trust of the mining industry. That is why the established technologies still being the first choice. And, in comminution, that first choice are SAG and ball mills. The design of ball mills has been well understood for a long time. The Bond Ball Mill Work Index is the standard test which helps to describe the ore in terms of energy requirements for milling. Unfortunately, the development of an equivalent test to characterize the ore subject to SAG milling has taken some time. As of today, several tests are available in the market, like the MacPherson test, the MinnovEX SAG Power Index (SPI™), the JK Drop Weight Test, the SMC Test® and the SAGDesign™ test (Verret et al., 2011). The SAGDesign™ test, developed by John Starkey in Canada in the early 2000s (Starkey et al., 2008, 2015), has become one of the standards to assess the grindability of an ore in a SAG mill. One of its advantages is the reduced sample mass needed to perform it, hence, the reduced cost. The second one is that the output of the test is straightforward, it is the energy required to grind the ore between two sizes. Because of this energetic approach, the results provided by the test can be directly applied to size a new mill or to assess the performance of an existing mill."

Jan 1, 2018

By S Kost, R Nievergelt, F Cortes

In recent years, the use of steel fibre-reinforced concrete (SFRC) for segmental tunnel linings has become increasingly popular due to numerous advantages including durability, resistance to spalling, reduced cracking at corners and edges and significant cost-saving potential. One of the key parameters for measuring the performance of SFRC is the residual (post crack) flexural strength. A problem often faced in design and quality control of SFRC is the high variability of results obtained by standard beam test methods, with reported coefficients of variability (CoV) in the order of 25 per cent. The high test variability results in a relatively low permissible design strength relative to the average flexural strength of the material and commonly leads to non-conformances with respect to residual flexural strength during production testing.This paper presents the implementation of an alternative testing method using large round determinate panels (RDPs) for quality control testing of the SFRC used in the segmental lining of the City East Cable Tunnel (CECT) in Sydney. The alternative RDP test method was found to correlate well with standard beam tests and significantly reduce the variability of test results, minimising the risk of outlying residual flexural strength results, with zero non-compliant test results reported during the production period.This successful implementation of an alternative test for post-crack flexural strength with lower variability in results constitutes a relevant precedent to demonstrate the feasibility of this approach which contributes to the development of more cost-effective concrete mixes and minimises the risk for non-compliant results and the contractual disputes that commonly arise from these.CITATION:Cortes, F, Nievergelt, R and Kost, S, 2014. Development of a segmental lining specification for steel fibre reinforced concrete flexural strength testing using round panel tests, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 461–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By B. Govindarajan, T. C. Rao

A simulation of batch-flotation experiments was carried out using a simple empirical model to identify the process parameters that would give maximum yield at any given ash level. The relationship between the maximum yield values and the percentage ash-reduction ratio (ARR) has shown two regions where the collector and the frother dosages have individual influences on the flotation performance. Based on this observation, a simple "selection-criterion diagram" is proposed. This diagram can he used to select the process parameters to achieve maximum yield, for a given ash content of the concentrate and at any given flotation period.

Jan 1, 1997

By D. C. Reid

This paper describes the latest results in research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. This research delivers enabling technologies that are essential in achieving increased roadway development rates as well as providing a safer working environment for underground mine personnel. Details are presented on technical developments and results of large-scale above-ground experiments conducted under field-realistic conditions. These experiments demonstrate the performance of the ?self-steering? capability which will enable a continuous miner (CM) to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the CM in real-time. Test results of a high performance navigation system utilising vehicle motion aiding technologies are presented. This system combines high performance inertial sensors, and custom-developed radar to achieve a navigation-grade guidance system. Comprehensive performance evaluation has been conducted using a scale skid-steer mobility platform operating autonomously through a typical roadway development mining pattern with a total path length of 2700 m and mission duration of 112 min. Results from this evaluation demonstrate that the sustained accuracy of the navigation system exceeds the original project expectations and is well suited to the requirements for this underground mining application. There are presently no known alternative methods for providing a practical and accurate three-dimensional guidance solution in this application. This achievement represents a significant milestone in delivering a step change improvement in underground coal mining roadway development.

Aug 1, 2013

By A. J. Davidson

A Cu-conducting solid electrolyte was used to develop the sensor. Instead of measuring the potential across the electrolyte from the reference material to the Cu-containing phase, a potential was applied and the stable current measured. This gave reasonable readings for copper-tin alloys, which agreed with the theoretical calculations, but was less satisfactory in the case of mattes because the surface area of electrolyte presented to the matte phase varied from sensor to sensor. To overcome this problem the potential was applied, the current was measured and then reversed and remeasured and the ratio of the currents was calculated. The current ratio is shown to be independent of the resistance of the electrolyte and the surface area of the electrolyte offered to the melt, but strongly dependent on the activity of the copper

Jun 21, 1905

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By Victor Rudenno

Feasibility studies for mining projects traditionally involve in their final stages a lengthy process of repetitive trial and error discounting, in calculating the discounted cash flow rate of return resulting from the respective yearly after-tax cash flows. Also, probability analysis and sensitivity analysis (in particular) require extensive additional calculations with each change of any project parameter . These inefficient repetitive procedures have two unacceptable results: 1. they are not flexible enough to allow ready analysis of dependent parameters , and 2. they require resort to high-capacity centralised computing facilities with their inherent impersonality, rather than a convenient and available desk calculator - a factor of particular importance to top mining management. Such problems can be overcome if the mining project can be represented by a reasonable straightforward mathematical economic model. The most flexible and appropriate model has been found to be one in which a maximum and minimum value for each of n parameters are supplied to a program which determines a large number of systematic combinations of parameter events and then statistically analyses them to determine the resulting coefficients of the model. In this paper the authors discuss the selection of the most appropriate type of model and outline the steps followed in its development and application.

Jan 1, 1977

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By Bill A. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six-head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin.The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill.The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator's station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt, and mesh sump.The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in tum lowers the miners' roof exposure per cut. This design reduces the operator's exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore, the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely."

Jan 1, 2016

By B. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin. The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill. The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and then two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator’s station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt and mesh sump. The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in turn lowers the miners’ roof exposure per cut. This design reduces the operator’s exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely. INTRODUCTION When mining underground it is necessary to support the roof quickly to prevent it from collapsing after an area has been mined. Since the 1950s, the primary method for supporting the roof has been the installation of roof bolts. Roof bolting is one of the most basic functions yet one of the dangerous jobs in the underground mining operation (1). The Mine Safety and Health Administration’s (MSHA) Health and Safety Accident Classification injury database showed an average of 660 roof bolter operator accidents per year over a 5-year period (1999-2003) (2). The numbers show that roof bolting is the most hazardous machine-related job in underground mining. It represents 39 percent of all machine-related accidents in underground coal mines. In 1993, the U.S. Bureau of Mines conducted a study that has shown the activity of drilling as the most hazardous job task performed by a roof bolter operator, accounting for 31 percent of all roof bolting injuries (3). Almost half (46%) of these drilling injuries were due to falling rocks or coal from the roof. All of these injuries occurred under supported roof. The majority of these injuries (about 99%) are not caused by a major roof collapse but from falls of smaller rock from the immediate roof. This type of roof failure has also been termed “skin fall.”"

Jan 1, 2017

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By John Bullock

Limestone and dolomite quarries were mapped to determine specific failure mechanisms for the various geologic and structural conditions. Algorithms for analyzing these mechanisms were incorporated into a software package together with ranges of physical properties such as joint shear strength, angle of internal friction, and cohesion for specified lithologic units. Reliability options using Monte Carlo sampling and sensitivity studies are included to evaluate alternative highwall designs. The package is designed to facilitate progressive stability evaluation of quarry highwalls as mining continues. This package includes an optimum design protocol that can be followed to avoid the potential of massive failure. The program was developed in conjunction with the quarry industry and is demonstrated using case studies.

Jan 1, 1993

Papua New Guinea is geologically prospective for large, medium and small mineral discoveries. All profitable developments to date have been very large mines but for every large mine there should be many small mines which could be developed under appropriate circumstances.The Papua New Guinea Government should, with appropriate changes to fiscal, legislative and policy regimes, create a favourable exploration envir-onment to encourage a major increase in exploration by small exploration companies and subsequent discoveries and mine development.

Jan 1, 1994

By Paul Worsey, Matthew Coy

In the blasting industry, many different techniques are used to estimate and examine the effects of varying explosives and blast designs on the breakage of a rock mass. The overall objective is to find a cost-minimized blasting solution that also conforms to the legal and environmental concerns related to blasting. A major drawback to current blasting methods is the inability to account for "caprock," or a thick overlying layer found in sedimentary rocks that creates large amounts of oversize blasted material, especially on the top of a muck pile. This can lead to underestimating oversize in shots with massive top layers. A better fundamental understanding of blasting processes with caprock is required.

Jan 1, 2018