Search Documents

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988

By C. J. Johnson, C. J. Bise

Abstract - As the US coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face- ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 68% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing techno- logical climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1990

By Richard Deakin

This case study describes aspects of the design of bridge foundations using 320mm diameter steel tube piles in the vicinity of Montréal, Canada. In this area, these piles are a very commonly used and cost effective solution for deep foundations. Typically they are driven through thick Champlain Sea Clay to bear onto stiff, strong rock. However, in some locations there is a layer of glacial till between the base of the clay and the rock which cannot always be fully penetrated by the piles. There is currently little published information, about the bearing capacity of these piles in the local till, and this paper presents and discusses some pile-test data from a recent project. The nature of the glacial deposits in the study area is presented using information gained from published geological data, the project ground investigations and site observations. The design approach and assumptions are discussed, together with the aims and outcomes of preliminary field driving trials and pile tests. The paper then discusses the results of dynamic tests undertaken on production piles. Bearing capacity factors are back analysed from the dynamic test results and compared against values assumed within the design. Observations are made that designers of future foundations in similar conditions may find informative.

Jan 1, 2011

By and M. V Roper, H. N. Engelbrecht

Quality control interventions emanate from process upsets and trends that move product quality beyond the natural variation expected in a stable process. The ability to detect upset conditions and react in an effective manner protects both resource utilisation and compliance to specifications. Product quality control on coal processing plants traditionally relies on the reference (combined sampler and laboratory) system to measure product qualities. The introduction of online analyser (OA) technology, applied in different configurations, creates a second source of measurement information for control decision making. The case study was done on the primary sample stream of the final product stream at Exxaro’s GG7 and 8 plants, part of the Grootegeluk complex. It explores the OLA system’s ability to meet the OEM performance guarantee, perform equally to the reference system without analytical delay time, and assesses the effort to achieve this performance in a by-line analyser (BLA) configuration. In the paper, a conceptual comparison of the two measurement systems is done and the theoretical and practical comparison of measurement performance is discussed. Results demonstrate that the OA outperformed the OEM’s performance guarantee and achieved similar levels of performance to the reference system without the response delay. Keywords: Online analyser (OLA), by-line analyser (BLA), coal quality measurement, measurement performance

Jan 1, 2020

By Layton C. Binon

Exploration budgets are commonly determined by "rules of thumb" such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve the goals of the company. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1981

By L. C. Binon

Exploration budgets are commonly determined by rules of thumb, such as a percentage of earnings or other fiscal measure. An appropriate exploration budget is the amount needed to achieve company goals. It can be determined by discounting the income expected from achieved goals. Budgets for individual projects are determined in a similar manner except that risk of failure is included in the computation.

Jan 1, 1984

By B. Genc, P. Malepfane

This study proposes a new approach to reduce the environmental impact during surface mining by improving environmental factors through the incorporation of carbon footprint into strategic mine planning. Two key variables were analysed by contrasting and comparing the baseline and optimised models generated. These variables include net present value, which helps determine the financial feasibility of the mining models and their carbon emissions. The variables were analysed by using linear regression, Spearman’s correlation, a P-value hypothesis, and an exponential decay test. Results show that at Mine A the projected net present value was 62% higher than when running a baseline model. Furthermore, the net present value from the baseline model portrayed a high rate of decay at 0.667 versus 0.118 from the optimised model. This indicates the baseline model’s sensitivity to long-term project timelines and fluctuating markets. The optimised method presents an opportunity to manage emissions during the high operational costs phases. It is represented by a 31% improvement in carbon emissions during the periods of high operational costs, whilst maintaining a positive net present value when compared with the baseline model. It was shown that the optimised model presents a better chance of achieving financial feasibility and balancing environmental impact, thereby ensuring that Mine A can align with the environmental aspect of economic, social, and governance principles through lowering the carbon footprint resulting from its hauling operations.

Jan 30, 2026

By J. P. Nairn, C. M. McCulloch

More and more underground mining is being conducted using the long wall method. Likewise, many new surface mines use area or mountaintop removal methods. These methods can have a significant impact on surface and ground water resources. The overall study of the effects on surface and ground water from mining is referred to as the probable hydrologic consequences (PHC) determination of mining and reclamation. Collection and interpretation of information concerning ground water and surface water quality and quantity, as well as detailed geologic analysis, is required to adequately define the impacts of mining. This paper discusses the present day requirements and methodology of preparing a PHC for a large mining operation in the eastern coalfields.

Jan 1, 1997

By C. M. McCulloch

More and more mining underground is being conducted using the longwall method. Likewise, many new surface mines use area or mountaintop removal methods. These methods can have a significant impact on surface and groundwater resources. The overall study of the effects on surface and groundwater from mining is referred to as the probable hydrologic consequences (PHC) determination of mining and reclamation. Collection and interpretation of information concerning groundwater and surface water quality and quantity, as well as detailed geologic analysis, is required to adequately define the impacts of mining. This paper discusses the present day requirements and methodology of preparing a PHC for a large mining operation in the eastern coalfields.

Jan 1, 1995

By R Mann, R Prasad, S Vink, V Nanjappa

The level of salinity that various aquatic organisms can tolerate without incurring any adverse effects is dependent on several environmental and evolutionary factors. These factors include the relative concentrations of different types of dissolved salts in the water that makes up their habitat, the regimes to which organisms are exposed to waters of differing salinity levels (including naturally derived variations), the degree to which an organismÆs life history stages have adapted to salinity, an organismÆs ability or behaviour to avoid adverse levels of salinity and an organismÆs capacity for osmoregulation.Release of saline water into rivers of the Fitzroy catchment has created concern about the impact on aquatic organisms. Not only is salinity itself a stressor on organisms but different ionic compositions will moderate the effects. Ecotoxicology experiments were conducted using artificial saline water based on mine water chemistry using sensitive macroinvertebrates collected from the catchment, as well as a range of laboratory organisms in accordance with the ANZECC and ARMCANZ (2000) guidelines. The 95 per cent ecosystem protection value calculated from species sensitivity distribution derived from the commercial tests was estimated to be ~2.0 mS/cm. For the protection of 99 per cent of the species the salinity has to be reduced by more than 50 per cent to 0.91 mS/cm. The electrical conductivity (EC) values, derived by commercial testing and species sensitivity distribution in this study suggests that salinity contaminant trigger values previously developed using a referential approach for protection of aquatic ecosystems from saline mine water releases in the Fitzroy may be conservative.CITATION:Vink, S, Mann, R, Nanjappa, V and Prasad, R, 2013. Determining the impacts of salinity on freshwater organisms, in Proceedings Water in Mining 2013 , pp 149-154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By E. Heikkinen, J. Suikkanen, T. Siren, J. Valli, M. Hakala

Diametrically faced borehole breakout observations are a fairly good indication of magnitude of the secondary stresses acting perpendicular to the borehole. In cases of low in situ stresses, where borehole breakouts are not observed naturally, it is possible to increase the prevailing stress state around the borehole by increasing the rock temperature. When the temperature is increased sufficiently, thermally induced borehole breakouts will occur. By implementing the temperature increase in boreholes located at excavated tunnels, it is also possible to study the effect of the near-field stresses caused by the excavation. The near-field stress state changes as a function of borehole depth, thus increasing the information available from experiment. To study the feasibility of this proposed low cost method, a Borehole Thermal Spalling (BTS) experiment was executed in ONKALO Underground Rock Characterization Facility, in Western Finland in 2014. The first borehole pilot test with the method was conducted in ONKALO at the POSE niche in already at May 2010, with the second pilot test following in August 2010 at Äspö HRL. The major objective of the experiments was to define the trend of the maximum in situ stress component, while also providing knowledge of the in situ spalling strength of the ONKALO rock mass. The stress state in ONKALO is nearly isotropic in horizontal layer, causing problems for the use of more traditional stress measurement methods. With boreholes heated over long interval, the weakest rock parts are observed to fail, thus providing statistical confidence. For these reasons, continuous test sections have an advantage in ONKALO, compared to spatially limited stress measurement methods such as overcoring and hydraulic fracturing. The BTS experiment is conducted in 9 meter deep vertical boreholes located at the POSE niche, situated -345 m depth below the ground surface. The boreholes used within the BTS experiment are located in migmatitic granite, in an experiment area where the surrounding stress state and the rock strength are fairly well known. The prior knowledge of the stresses is favourable for the experiment, as it requires careful planning and iterations to determine the appropriate heating power domain. Too low heating power will not be sufficient to cause borehole breakout, while too high heating power causes breakout in all directions thus making determination of stress direction hard or impossible. The initial state of the borehole and induced borehole breakouts will be monitored using acoustic televiewer logging (ABI) and optical borehole logging (OBI) imaging techniques. Fracture mechanics modelling is used in planning of the experiment, also in back-analysis to link the observed breakout angle to stress state. Both the pilot test in 2010 and BTS test in 2014 resulted in similar borehole breakout direction. The results are in line with so called EDZ & VT1 stress interpretation, revealed the maximum horizontal component bearing the magnitude of 21.5 MPa, with the trend of 166°.

Jan 1, 2015

By Robert J. Timko, R. Lincoln Derick

The Bureau of Mines evaluated the integrity of escapeways in a three entry underground coal mine. A center conveyor belt entry (secondary escapeway), was flanked by an intake (primary escapeway) and a return entry. Diesel equipment was used throughout the mine for material and personnel haulage. A carbon monoxide monitoring system, tied to a data recording computer on the surface, was deployed throughout the belt entry and at selected sites in the intake and return entries. Previously, the company had a fire of unknown origin in another mine, which prompted an interest in the performance of their escapeways. An initial, qua1itative evaluation was performed by burning approximately 14 kg of coal at the mouth of the intake entry. The first test was followed by a similar burn at the mouth of the belt entry. These initial trials showed a high quantity of leakage between entries. In several follow-up evaluations, simulated fires, using a tracer gas, were set in the intake and belt entries. Tracer gas concentrations were obtained in all entries at four different underground locations. The results of these tests showed that permanent stoppings could not guarantee isolated, contaminant-free escapeways.

Jan 1, 1989

By K. C. Corin, M. S. Manono

The mining and mineral concentration of Cu-Ni-PGM sulfide ores in South Africa occurs in semiarid regions. The scarcity and availability of water resources in these regions has become one of the biggest challenges facing mineral concentrators.S Owing to this challenge, concentrators have to find ways through which they can manage and control their water usage. Recycling and re-use of process water in mineral concentrators has therefore become common practice. This practice is beneficial in that it reduces reliance on municipal water, harnesses compliance to stringent environmental regulations on water usage, and it also offers a better response to the Sustainable Development Goals. This could however be somewhat concerning to the operator as recirculated water often has higher concentrations of ions compared to fresh or potable water. The unintended change in the process water quality may potentially affect critical aspects of flotation such as the stability of the froth. This has led to the need to find those process water ions that have the greatest impact on froth stability. Thus, this paper investigates the effect of various ions common in process water of a typical Cu-Ni-PGM concentrator on froth stability. Bubble size, water recoveries, foam height, and dynamic froth stability in both twophase and three-phase flotation systems are used as proxies for froth stability. Findings of this study are deemed crucial towards the development of a process water management protocol in sulfidic Cu-Ni- PGM ore concentrators. Keywords: Bubble diameter, electrolytes, flotation, froth stability, water quality

Jan 1, 2020

Present value maximisation studies are a useful aid in enhancing the economic performance of open pit mining operations. Maximising present value helps to reduce the risk of financial failure. Maximisation of present value also means that the capital invested is being used most efficiently. A characteristic step in determining the present value of an open pit mining operation is to set out the sequence in which increments of material (ore of various grades and waste rock) are mined. Traditionally, present value maximisation has been performed by selecting a cut-off grade for each increment so as to maximise the present value of the total operation, by an iterative process using computers. Kenneth F Lane has developed a method and applied it to many mining operations. An alternative method for determining the maximum present value of an open pit mining operation is given. In this method the maximum present value is determined by working backwards from the end of the operation life, progressively asking the question of each increment `what cut-off grade maximises the the present value at the start of mining of that increment?' The method allows calculations to be performed by a `spreadsheet' package. Present value determinations are characteristically performed under constant conditions (eg prices, costs) throughout the operation life. Unfortunately real life circumstances are rarely constant, with the costs of mining inputs rising at variable rates. The prices received for mineral products have been shown to broadly trend downwards with time in real terms. Treatment of such changes in the determination of the maximum present value of an operation is discussed.

Jan 1, 1994

By J. D. Bosman, L. J. Gardner

"The Bushveld Complex is a large layered igneous intrusion, located in the northern parts of the Republic of South Africa. The complex hosts the largest known reserves of Platinum Group Metals in the world. On the western limb of the complex, mining of the Merensky economic horizon and UG2 chromitite layer has been conducted for many years by several mining companies, including Impala Platinum Limited. Over the past decade, Impala has planned a new generation of greenfield vertical shafts, commencing with comprehensive geological and geotechnical studies. As part of the geotechnical studies, numerous tests have been conducted to quantify the mechanical properties of the various near-reef rock types. These tests include point load tests conducted in the field, as well as uni-axial compressive strength, triaxial compressive strength, and Brazilian disc tensile strength tests conducted in specialist laboratories. The authors have compiled an extensive database containing a large number of tests for different rock types, ranging from felsic Anorthosite to mafic Pegmatoid. The database was analysed to quantify the mechanical properties and values for Mohr Coulomb and Hoek Brown failure criteria for each rock type typically exposed by mining. The paper will provide a data set of rock mechanical properties typically used in numerical modelling and other design processes. Using the significant number of tests available, data describing the variability of the various parameters will be included."

Jan 1, 2015

By L. Chunpongtong

ABSTRACT The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By L. Chunpongtong

The mining limit in oil sands is regulated by the ratio of total mining volume (ore, interburden, and overburden) one has to mine per volume of bitumen in place (TV/BIP). This paper presents a mathematical solution for creating the most economical pit outline where the TV/BIP ratio upper limit is 12, by combining mining economic theory and the Lerchs-Grossmann (LG) algorithm.

Jan 1, 2014

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. M. Mutmansky, Y. J. Wang, H. L. Hartman

Procedures for determining the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques have been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the many mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To simplify the development of procedures for determining the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well, and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1986

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988